The Effects of Chromophore Halogenation on the Stability of UV-Absorbing Organic Solar Cells
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
SEARCH · Engineering Papers
Results for “active layer”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Research into the feasibility of metal- and oxide-film capacitors
Thin film capacitors with up to twenty-two active layers have been deposited by RF sputtering. The materials were aluminum electrodes of 1200 to 1500 angstrom thickness and silica dielectric layers of 3000 to 6000 angstrom thickness. The best electrical characteristics were capacitances of nearly 0.1 microfarad for an active area of 1.25 square centimeters, dissipation factor of less than 0.01 over a frequency range of 0.5 to 100 kilohertz and energy density of approximately 70 millijoules per cubic centimeter of active deposited material at a working voltage of 40 volts. These aluminum-silica capacitors exhibit excellent electrical stability over a temperature range from -55 C to +300 C.
Jorgenson, G. V.↗
Hybrid Damping System for an Electronic Equipment Mounting Shelf
The objective of this study was to design and construct a vibration control system for an electronic equipment shelf to be evaluated in the NASA Dryden FTF-11. The vibration control system was a hybrid system which included passive and active damping techniques. Passive damping was fabricated into the equipment shelf using ScothDamp(trademark) damping film and aluminum constraining layers. Active damping was achieved using a two channel active control circuit employing QuickPack(trademark) sensors and actuators. Preliminary Chirp test results indicated passive damping smoothed the frequency response while active damping reduced amplitudes of the frequency response for most frequencies below 500Hz.
Voracek, David↗
Hybrid Damping System for an Electronic Equipment Mounting Shelf
The objective of this study was to design and construct a vibration control system for an electronic equipment shelf to be evaluated in the NASA Dryden FTF-II. The vibration control system was a hybrid system which included passive and active damping techniques. Passive damping was fabricated into the equipment shelf using ScothDamp(trademark) damping film and aluminum constraining layers. Active damping was achieved using a two channel active control circuit employing QuickPack(trademark) sensors and actuators. Preliminary Chirp test results indicated passive damping smoothed the frequency response while active damping reduced amplitudes of the frequency response for most frequencies below 500Hz.
Voracek, David↗
Nanotube Film Electrode and an Electroactive Device Fabricated with the Nanotube Film Electrode and Methods for Making Same
Disclosed is a single wall carbon nanotube (SWCNT) film electrode (FE), all-organic electroactive device systems fabricated with the SWNT-FE, and methods for making same. The SWCNT can be replaced by other types of nanotubes. The SWCNT film can be obtained by filtering SWCNT solution onto the surface of an anodized alumina membrane. A freestanding flexible SWCNT film can be collected by breaking up this brittle membrane. The conductivity of this SWCNT film can advantageously be higher than 280 S/cm. An electroactive polymer (EAP) actuator layered with the SWNT-FE shows a higher electric field-induced strain than an EAP layered with metal electrodes because the flexible SWNT-FE relieves the restraint of the displacement of the polymeric active layer as compared to the metal electrode. In addition, if thin enough, the SWNT-FE is transparent in the visible light range, thus making it suitable for use in actuators used in optical devices.
Kang, Jin Ho↗
Methods for Making an Electroactive Device Fabricated with a Nanotube Film Electrode
Disclosed is a single wall carbon nanotube (SWCNT) film electrode (FE), all-organic electroactive device systems fabricated with the SWNT-FE, and methods for making same. The SWCNT can be replaced by other types of nanotubes. The SWCNT film can be obtained by filtering SWCNT solution onto the surface of an anodized alumina membrane. A freestanding flexible SWCNT film can be collected by breaking up this brittle membrane. The conductivity of this SWCNT film can advantageously be higher than 280 S/cm. An electroactive polymer (EAP) actuator layered with the SWNT-FE shows a higher electric field-induced strain than an EAP layered with metal electrodes because the flexible SWNT-FE relieves the restraint of the displacement of the polymeric active layer as compared to the metal electrode. In addition, if thin enough, the SWNT-FE is transparent in the visible light range, thus making it suitable for use in actuators used in optical devices.
Kang, Jin Ho↗
Boosting the Oxygen Evolution Reaction by Tuning the Interfacial Iron Adsorption on Layered Double Hydroxide
Understanding the interaction between ions in the electrolyte and electrode materials plays an important role in optimizing the water electrolysis performance for hydrogen production. Herein, the synergistic effect of iron (Fe) in the electrolyte and interlayer anions within the layered structure on the oxygen evolution reaction (OER) has been investigated by combining material synthesis with controlled structure, multiple characterization techniques, and first-principles calculations. Nickel aluminum layered double hydroxides (NiAl-LDHs) with different interlayer anions (CO 3 2– , Cl – , and Br – ) show similar oxygen evolution activity in the absence of Fe species in the electrolyte. The addition of Fe into the electrolyte results in improved performance for all of the NiAl-LDHs, following the rank LDH-Br > LDH-Cl > LDH-CO 3 , under all of the conditions with varied concentration of Fe. X-ray absorption spectroscopy and identical location electron microscopy analyses show that the LDH structure remains unchanged after the OER activity test, while in situ stationary probe rotating disk electrode inductively coupled plasma mass spectrometry (SPRDE-ICP-MS) measurements show partial dissolution of the intercalating halide ions during cycling, with less dissolution for Br-intercalated materials. Insights from theoretical calculations demonstrate the thermodynamic preference of Br – to remain intercalated in the presence of Fe, while the stronger adsorption of Fe(OH) 3 species on the LDH-Br sample promotes the OER activity. In conclusion, these results provide mechanistic insights into the rational design of active layered materials with an enhanced OER performance for efficient water electrolysis.
58 GEOSCIENCES↗
Optimization of the electron transport layer in quantum dot light-emitting devices
Quantum dot light-emitting devices have emerged as an important technology for display applications. Their emission is a result of recombination between positive and negative charge carriers that are transported through the hole and electron conductive layers, respectively. The selection of electron or hole transport materials in these devices not only demands the alignment of energy levels between the layers but also balances the flow of electrons and holes toward the recombination sites. In this work, we examine a method for device optimization through control of the charge carrier kinetics. We employ impedance spectroscopy to examine the mobility of charge carriers through each of the layers. The derived mobility values provide a path to estimate the transition time of each charge carrier toward the emitting layer. We suggest that an optimal device structure can be obtained when the transition times of both charge carriers toward the active layer are similar. Finally, we examine our hypothesis by focusing on thickness optimization of the electron transport layer.
36 MATERIALS SCIENCE↗
Conversion efficiency improvement of ELO GaAs solar cell, deposited on water soluble sacrificial buffer
Here, we demonstrate the improvement of power conversion efficiency of an epitaxially-lifted-off single junction GaAs solar cell deposited on a water-soluble sacrificial buffer architecture by introducing an additional germanium (Ge) interlayer between GaAs and the fluoride buffer. The epitaxial lift-off (ELO) technique has been extensively used to separate III-V device layers from their single crystal GaAs substrates. However, conventional ELO requires the use of concentrated hydrofluoric acid (HF) for extended times to etch out the sacrificial layer, subsequently degrading the surface roughness of the parent wafer. As a result, the wafer has to undergo expensive and intensive chemical mechanical polishing (CMP) processes, costing about 25% of a pristine 6-inch GaAs substrate. In our previous work, we demonstrated a method to eliminating the need for CMP post-processing by using water-assisted ELO (H 2 O-ELO). A water-soluble, 3-layer buffer architecture was developed using alkaline earth compounds. However, devices suffered low performance due to a high defect density in the GaAs active layers. A Ge interlayer was introduced to provide a more favorable surface energy for GaAs growth, which leads to an improvement of GaAs crystal quality. The Ge deposition conditions were optimized to achieve a high-quality Ge layer on triple-layer fluoride buffer. Single junction GaAs devices fabricated on Ge/(Ca,Sr)F 2 /BaF 2 /(Ca,Sr)F 2 showed improvement of solar cell performance parameters featuring increases in V oc by 23.7%, and fill factor (F.F.) by 4.9%, which results in an overall improvement of power conversion efficiency from 10.3% to 12.69%.
14 SOLAR ENERGY↗
AlGaAs/GaAs transverse junction stripe lasers with distributed feedback
Transverse junction stripe (TJS) lasers with periodic feedback were fabricated in two geometries. An interferometric and wet chemical etching technique was used to create a feedback grating across the entire pumping region for the distributed feedback (DFB) TJS laser and to create the separate distributed Bragg reflectors/DBR) for the TJS/DBR laser. The TJS/DFB laser was a double heterostructure device grown by liquid phase epitaxy (LPE) and had a third order grating etched in the top ALO.2GaO.8As layer. The grating was buried by growing an ALO.35GaO.65As layer on the grating by metal organic chemical vapor deposition (MO-CVD). The TJS/DBR laser was also fabricated in an LPE double heterostructure. The top AlGaAs layer was thinned to 0.1 micron over more than half of the laser so that the grating would be close to the GaAs active layer and optical field. Single mode operation in both configurations was obtained. The thermal shift of the laser wavelength in both cases was less than 1 Angstrom/deg K, compared to the 3 Angstrom/deg K shift of the spontaneous emission peak.
Hafich, M. J.↗
Investigating the effect of aluminum oxide fixed charge on Schottky barrier height in molybdenum oxide-based selective contacts
A tunneling atomic layer deposited (ALD) AlO x layer was inserted in a Si|SiO x |AlO x |MoO x |metal tunnel diode structure to investigate the impact of fixed interface charge on Schottky barrier height. ALD AlO x provides a synthesis-tunable fixed charge and can provide excellent field effect passivation at the SiO x |AlO x interface. A large (>1 × 10 12 q.cm –2 ) negative fixed charge density was expected to decrease Schottky barrier height on p-type silicon and increase Schottky barrier height on n-type silicon by up to 0.4 eV based on an electrostatic model. Fixed charge density and interface trap state density were measured using a thick layer of AlO x in metal oxide semiconductor capacitor structures (MOSCAPs); Schottky barrier height and specific contact resistivity were measured using a tunneling-active layer of AlO x in contacted structures with MoO x . In some samples, HfO x interface layers were inserted between AlO x and silicon to quench the fixed negative charge. The Schottky barrier height was found to vary with processing conditions but did not have a strong correlation with expected fixed charge density. Here, while fixed charge may play a role in determining the Schottky barrier height, other parameters also have significant affect. Further work is needed to minimize contact resistivity and elucidate other factors impacting the Schottky barrier height.
14 SOLAR ENERGY↗
Structure of Layers Formed by [2-(3,6-Disubstituted-9 H -carbazol-9-yl)ethyl]phosphonic Acids on Metal Oxides
[2-(9 H -Carbazol-9-yl)ethyl]phosphonic acid (2PACz) and its derivatives are being used extensively as hole-transport layers in organic and perovskite solar cells due to their ability to modify electrode work function, surface wettability, and in some cases, to improve active-layer adhesion, while minimizing interfacial energy losses. The orientation and coverage of surface modifiers significantly impact these functional properties; however, the detailed structure and packing in these overlayers are challenging to investigate, leading to a lack of understanding of how this structure and packing influence performance and limiting the ability to rationally design molecular modifiers. Here, we investigate monolayers of 2-(9 H -carbazol-9-yl)ethyl phosphonic acid derivatives (from here on referred to as X-2PACz) on indium tin oxide (ITO) and alpha phase aluminum oxide (α-Al 2 O 3 ) using a combination of X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, and X-ray reflectivity (XRR). By correlating elemental ratios, molecular orientation, and electron density profiles, we directly quantify surface coverage, layer thickness, and molecular tilt across a series of chemically related monolayers. We find that 2PACz and the X-2PACz derivatives form dense monolayers on α-Al 2 O 3 and ITO, with similar surface coverages on either substrate that are inversely proportional to molecular steric bulk. These surface coverage results indicate that X-2PACz is sterically limited in its monolayer surface packing density, as opposed to site limited. Despite surface packing density differences between molecules, the NEXAFS data show a constant average molecular orientation of 61° to 65° between the plane of the carbazole and the substrate for all the molecules on both substrates. These results increase our general understanding of 2PACz derivatives as they become increasingly useful in high performance solar cells.
NEXAFS↗
Extrinsic germanium Blocked Impurity Bank (BIB) detectors
Ge:Ga blocked-impurity-band (BIB) detectors with long wavelength thresholds greater than 190 microns and peak quantum efficiencies of 4 percent, at an operating temperature of 1.8 K, have been fabricated. These proof of concept devices consist of a high purity germanium blocking layer epitaxially grown on a Ga-doped Ge substrate. This demonstration of BIB behavior in germanium enables the development of far infrared detector arrays similar to the current silicon-based devices. Present efforts are focussed on improving the chemical vapor deposition process used to create the blocking layer and on the lithographic processing required to produce monolithic detector arrays in germanium. Approaches to test the impurity levels in both the blocking and active layers are considered.
Krabach, Timothy N.↗
Multimodal microscopy of extended defects in β-Ga 2 O 3 (010) EFG crystals
Beta-phase gallium oxide (β-Ga 2 O 3 ) has attracted attention in recent years as a potentially low cost, large area substrate and active layer material for high power, high temperature power electronics and sensing devices. However, growth of β-Ga 2 O 3 crystals is complicated by easily activated (100) and (001) cleavage planes, the presence of low angle grain boundaries (LAGBs) and twins, and the potential formation of polycrystalline grains. In this study, β-Ga 2 O 3 crystals were grown by the edge-defined film-fed growth technique with an (010) principal face. Two crystals with apparently randomly formed high angle grain boundaries (HAGBs) were selected and analyzed by electron backscatter diffraction, electron channeling contrast imaging, and cathodoluminescence to investigate the nature of the LAGBs and the source of the HAGB formation. It was discovered that planar LAGBs lying parallel to the (010) plane exist in the region immediately preceding the start of an HAGB. Increased misorientation across the LAGB was observed, approaching the initiation of a new grain. We present multimodal microscopy characterization, correlating misorientation and variation in optoelectronic properties with LAGBs and the associated dislocations.
14 SOLAR ENERGY↗
Nanoscale Electronic Transparency of Wafer-Scale Hexagonal Boron Nitride
We report monolayer hexagonal boron nitride (hBN) has attracted interest as an ultrathin tunnel barrier or environmental protection layer. Recently, wafer-scale hBN growth on Cu(111) was developed for semiconductor chip applications. For basic research and technology, understanding how hBN perturbs underlying electronically active layers is critical. Encouragingly, hBN/Cu(111) has been shown to preserve the Cu(111) surface state (SS), but it was unknown how tunneling into this SS through hBN varies spatially. Here, we demonstrate that the Cu(111) SS under wafer-scale hBN is homogeneous in energy and spectral weight over nanometer length scales and across atomic terraces. In contrast, a new spectral feature-not seen on bare Cu(111)-varies with atomic registry and shares the spatial periodicity of the hBN/Cu(111) moiré. This work demonstrates that, for some 2D electron systems, an hBN overlayer can act as a protective yet remarkably transparent window on fragile low-energy electronic structure below.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Origin of layered perovskite device efficiencies revealed by multidimensional time-of-flight spectroscopy
Mixtures of layered perovskite quantum wells with different sizes form prototypical light-harvesting antenna structures in solution-processed films. Gradients in the bandgaps and energy levels are established by concentrating the smallest and largest quantum wells near opposing electrodes in photovoltaic devices. Whereas short-range energy and charge carrier funneling behaviors have been observed in layered perovskites, our recent work suggests that such light-harvesting processes do not assist long-range charge transport due to carrier trapping at interfaces between quantum wells and interstitial organic spacer molecules. Here, we apply a two-pulse time-of-flight technique to a family of layered perovskite systems to explore the effects that interstitial organic molecules have on charge carrier dynamics. In these experiments, the first laser pulse initiates carrier drift within the active layer of a photovoltaic device, whereas the second pulse probes the transient concentrations of photoexcited carriers as they approach the electrodes. The instantaneous drift velocities determined with this method suggest that the rates of trap-induced carrier deceleration increase with the concentrations of organic spacer cations. Overall, our experimental results and model calculations suggest that the layered perovskite device efficiencies primarily reflect the dynamics of carrier trapping at interfaces between quantum wells and interstitial organic phases.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Radio model of the transition layer in solar active regions
Radio model of brightness temperature and electron density in transition layer of solar active regions, using Laplace transformation and hydrostatic equilibrium equation
Chiuderi, C.↗
Light–matter coupling in large-area van der Waals superlattices
Two-dimensional (2D) crystals have renewed opportunities in design and assembly of artificial lattices without the constraints of epitaxy. However, the lack of thickness control in exfoliated van der Waals (vdW) layers prevents realization of repeat units with high fidelity. Recent availability of uniform, wafer-scale samples permits engineering of both electronic and optical dispersions in stacks of disparate 2D layers with multiple repeating units. In this study, we present optical dispersion engineering in a superlattice structure comprising alternating layers of 2D excitonic chalcogenides and dielectric insulators. By carefully designing the unit cell parameters, we demonstrate greater than 90% narrow band absorption in less than 4 nm of active layer excitonic absorber medium at room temperature, concurrently with enhanced photoluminescence in square-centimetre samples. These superlattices show evidence of strong light–matter coupling and exciton–polariton formation with geometry-tuneable coupling constants. Our results demonstrate proof of concept structures with engineered optical properties and pave the way for a broad class of scalable, designer optical metamaterials from atomically thin layers.
2D Crystals↗