Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Calculation of Wing Bending Moments and Tail Loads Resulting from the Jettison of Wing Tips During a Symmetrical Pull-Up

A preliminary analytical investigation was made to determine the feasibility of the basic idea of controlled failure points as safety valves for the primary airplane structure. The present analysis considers the possibilities of the breakable wing tip which, in failing as a weak link, would relieve the bending moments on the wing structure. The analysis was carried out by computing the time histories of the wing and stabilizer angle of attack in a 10g pull-up for an XF8F airplane with tips fixed and comparing the results with those for the same maneuver, that is, elevator motion but with tips jettisoned at 8g. The calculations indicate that the increased stability accompanying the loss of the wing tips reduces the bending moment an additional amount above that which would be expected from the initial loss in lift and the inboard shift in load. The vortex shed when the tips are lost may induce a transient load requiring that the tail be made stronger than otherwise.

Boshar, John↗
NASA NTRS2001

Compressor Stall Recovery Through Tip Injection Assessed

Aerodynamic stability is a fundamental limit in the compressor design process. The development of robust techniques for increasing stability has several benefits: enabling higher loading and fewer blades, increasing safety throughout a mission, increasing tolerance to stage mismatch during part-speed operation and speed transients, and providing an opportunity to match stages at the compressor maximum efficiency point, thus reducing fuel burn. Mass injection upstream of the tip of a high-speed axial compressor rotor is a stability enhancement approach known to be effective in suppressing stall in tip-critical rotors if the injection is activated before stall occurs. This approach to stall suppression requires that a reliable stall warning system be available. Tests have recently been performed to assess whether steady injection can also be used to recover from fully developed stall. If mass injection is effective in recovering from stall quickly enough to avoid structural damage or loss of engine power, then a stall warning system may not be required. The stall recovery tests were performed on a transonic compressor rotor at its design tip speed of 1475 ft/sec using four injectors evenly spaced around the compressor case upstream of the rotor. The injectors were connected to an external air source. In an actual engine application, the injected air would be supplied with compressor bleed air. The injectors were isolated from the air source by a fast-acting butterfly valve. With the injectors turned off, the compressor was throttled into stall. Air injection was then activated with no change in throttle setting by opening the butterfly valve. The compressor recovered from stall at a fixed throttle setting with the aid of tip injection. The unsteady operating characteristic of the rotor was measured during these tests using high-response pressure sensors located upstream and downstream of the rotor. The figure shows the results, where the unsteady pressure and mass flow are superimposed on the steady operating characteristic. The total injected mass flow was equal to 1.3 percent of the compressor flow. The solid line with no solid squares on it denotes the operating point during the beginning of throttle closure and the initial drop into stall. The gray traces denote the operating point during an additional throttle closure that occurred over the next 1200 rotor revolutions (4 sec). The dashed line denotes the recovery from stall that occurred during 90 rotor revolutions (0.3 sec) after the injectors were activated with no change in throttle setting. Tip injection not only recovers the compressor from stall, but also restores the compressor to its pre-stall level of pressure rise. In contrast, standard stall recovery schemes such as compressor bleed, stator vane actuation, or engine throttle modulation result in a loss of pressure rise across the compressor, which results in a loss of engine power.

Suder, Ken L.↗
NASA NTRS1993

Sensor tip for a robotic gripper and method of manufacture

A sensor tip (10) for use in a robotic hand has a three-dimensional compliant elastomeric body (12) with an outer boundary (22) having a circular base (24) and a convex surface (26) extending therefrom. Four strain transducers (14, 16, 18, and 20) produce electrical signals indicative of the strain at various positions near the boundary of the elastomeric body (12) resulting from forces exerted upon the sensor tip (10) by an object which the robotic hand is manipulating. The transducers (14, 16, 18, and 20) are positioned about the convex surface (26) so as to produce signals that may be decoupled to determine the normal and tangential forces and the applied torque. A buffer amplifier circuit (34), one for each of the transducers (14, 16, 18, and 20), receives the signals and provides quasi-steady state force information. The circuit (34) connects the respective transducer (40) in a feedback loop around an amplifier (36) and has desirable attributes for static charge buffering. The sensor tip (10) is calibrated to determine proportionality constants for the decoupling algorithm for use of a force delivering system (60), which uses voice coils (74) to apply a force that is linearly related to the current introduced to each of the coils (74). A method of manufacture of the sensor tip (10) results in improved bonding between the transducers (14, 16, 18, and 20) and the elastomeric body (12) for better performance and longer life of the sensor tip (10).

Lorenz, Robert D.↗
NASA NTRS1991

Sensor tip for a robotic gripper and method of manufacture

A sensor tip (10) for use in a robotic hand has a three-dimensional compliant elastomeric body (12) with an outer boundary (22) having a circular base (24) and a convex surface (26) extending therefrom. Four strain transducers (14, 16, 18, and 20) produce electrical signals indicative of the strain at various positions near the boundary of the elastomeric body (12) resulting from forces exerted upon the sensor tip (10) by an object which the robotic hand is manipulating. The transducers (14, 16, 18, and 20) are positioned about the convex surface (26) so as to produce signals that may be decoupled to determine the normal and tangential forces and the applied torque. A buffer amplifier circuit (34), one for each of the transducers (14, 16, 18, and 20), receives the signals and provides quasi-steady state force information. The circuit (34) connects the respective transducer (40) in a feedback loop around an amplifier (36) and has desirable attributes for static charge buffering. The sensor tip (10) is calibrated to determine proportionality constants for the decoupling algorithm for use of a force delivering system (60), which uses voice coils (74) to apply a force that is linearly related to the current introduced to each of the coils (74). A method of manufacture of the sensor tip (10) results in improved bonding between the transducers (14, 16, 18, and 20) and the elastomeric body (12) for better performance and longer life of the sensor tip (10).

Lorenz, Robert D.↗
NASA NTRS2014

Structural Health Monitoring on Turbine Engines Using Microwave Blade Tip Clearance Sensors

The ability to monitor the structural health of the rotating components, especially in the hot sections of turbine engines, is of major interest to aero community in improving engine safety and reliability. The use of instrumentation for these applications remains very challenging. It requires sensors and techniques that are highly accurate, are able to operate in a high temperature environment, and can detect minute changes and hidden flaws before catastrophic events occur. The National Aeronautics and Space Administration (NASA) has taken a lead role in the investigation of new sensor technologies and techniques for the in situ structural health monitoring of gas turbine engines. As part of this effort, microwave sensor technology has been investigated as a means of making high temperature non-contact blade tip clearance, blade tip timing, and blade vibration measurements for use in gas turbine engines. This paper presents a summary of key results and findings obtained from the evaluation of two different types of microwave sensors that have been investigated for use possible in structural health monitoring applications. The first is a microwave blade tip clearance sensor that has been evaluated on a large scale Axial Vane Fan, a subscale Turbofan, and more recently on sub-scale turbine engine like disks. The second is a novel microwave based blade vibration sensor that was also used in parallel with the microwave blade tip clearance sensors on the experiments with the sub-scale turbine engine disks.

Gas Turbine Engines↗
NASA NTRS1972

Preliminary performance of a low loading high tip speed fan stage

Limited data indicates the feasibility of designing fan stages for operation with weak oblique shocks in the rotor blade tip region. A 1600 ft/sec rotor tip speed fan indicated an overall efficiency of 0.846 at a pressure ratio of 1.51 even though the rotor blades had incurred damage in the leading edge tip region prior to obtaining the design speed performance. After the test it was observed that a number of the rotor blade mid-span dampers had failed, subsequently damaging a number of rotor blades in the leading edge tip region.

Bailey, E. E.↗
NASA NTRS1973

High-Tip-Speed, Low-Loading Transonic Fan Stage. Part 1: Aerodynamic and Mechanical Design

A high-tip-speed, low-loading transonic fan stage was designed to deliver an overall pressure ratio of 1.5 with an adiabatic efficiency of 86 percent. The design flow per unit annulus area is 42.0 pounds per square foot. The fan features a hub/tip ratio of 0.46, a tip diameter of 28.74 in. and operates at a design tip speed of 1600 fps. For these design conditions, the rotor blade tip region operates with supersonic inlet and supersonic discharge relative velocities. A sophisticated quasi-three-dimensional characteristic section design procedure was used for the all-supersonic sections and the inlet of the midspan transonic sections. For regions where the relative outlet velocities are supersonic, the blade operates with weak oblique shocks only.

Wright, L. C.↗
NASA NTRS1974

Experimental investigation of model variable-geometry and ogee tip rotors

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a model rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that properly selected variable geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance. Axial spacing of alternate blades was found to provide the greatest performance benefit, and further improvements were achieved by combining azimuth spacing with axial spacing. The performance benefit appears to be related to the relief of local adverse aerodynamic phenomena produced by vortex interference. The ogee tip design was found to substantially reduce the concentrated core intensity of the tip vortex, and could thus prove beneficial for the relief of blade-vortex interaction problems. However, the ogee tip was found to reduce hover performance at model scale.

Landgrebe, A. J.↗
NASA NTRS1974

Some effects of tip fins on wing flutter characteristics

A wind tunnel investigation has been conducted over the Mach number range from about 0.6 to 1.2 to determine the effects of large tip fins on the flutter characteristics of a swept wing. The basic wing configuration had an aspect ratio of 0.95, leading-edge sweep of 40 deg 0, and trailing-edge sweep of 21 deg. Two of these configurations were modified with tip fins of 60 deg dihedral and had effective aspect ratios of 1.5 and 2.2. In general, the results indicate that the addition of tip fins reduces the flutter speed, with the larger fin having the greater effect. Comparison of the experimental flutter speeds at Mach numbers between 0.60 and 0.90 with calculated values obtained by using doublet-lattice unsteady aerodynamic theory was good. Analytical results where structural and aerodynamic effects of the tip fins were isolated indicated that the reduction in flutter speed produced by the addition of the fins was caused by both effects, with the structural effect being the more pronounced.

Goetz, R. C.↗
NASA NTRS1974

Limitations to the small scale yielding approximation for crack tip plasticity

Recent finite-element results by S. G. Larsson and A. J. Carlsson suggest a limited range of validity to the 'small scale yielding approximation,' whereby small crack tip plastic zones are correlated in terms of the elastic stress intensity factor. It is shown with the help of a model for plane strain yielding that their results may be explained by considering the non-singular stress, acting parallel to the crack at its tip, which accompanies the inverse square-root elastic singularity. Further implications of the non-singular stress term for crack tip deformations and fracturing are examined. It is suggested that its effect on crack tip parameters, such as the opening displacement and J-integral, is less pronounced than its effect on the yield zone size.

Rice, J. R.↗
NASA NTRS1974

Fatigue crack propagation and cyclic deformation at a crack tip

The fatigue crack propagation relation da/dN = f(R) Delta K squared can be derived with three assumptions: small-scale yielding, material homogeneity, and that crack tip stresses and strains are not strongly affected by plate thickness. The function f(R) is a constant at a given stress ratio, R. The effects of plate thickness and stress ratio on crack tip deformation and fatigue crack growth in 2024-T351 aluminum alloy were studied. High Delta K level in a thin specimen causes crack tip necking. Necking is more pronounced at high stress ratio. Necking causes high maximum strain near a crack tip and fast crack growth rate.

Kang, T. S.↗
NASA NTRS1976

A plane strain analysis of the blunted crack tip using small strain deformation plasticity theory

A deformation plasticity analysis of the tip region of a blunted crack in plane strain is presented. The power hardening material is incompressible both elastically and plastically, in order to simulate behavior of a stress freezing material above critical temperature. Stress and displacement fields surrounding the crack tip are presented. The results indicate that the maximum stress seen at the crack tip is indeed limited and is determined by the tensile properties; however, the scale over which the stresses act is dependent on the loading. Comparisons are good between the forward crack tip displacement and micro-fractographic measurments of stretch zones observed in plane strain fracture toughness tests.

Mcgowan, J. J.↗
NASA NTRS1978

Performance with and without inlet radial distortion of a transonic fan stage designed for reduced loading in the tip region

A transonic compressor stage designed for a reduced loading in the tip region of the rotor blades was tested with and without inlet radial distortion. The rotor was 50 cm in diameter and designed for an operating tip speed of 420 m/sec. Although the rotor blade loading in the tip region was reduced to provide additional operating range, analysis of the data indicates that the flow around the damper appears to be critical and limited the stable operating range of this stage. For all levels of tip and hub radial distortion, there was a large reduction in the rotor stall margin.

Schmidt, J. F.↗
NASA NTRS1978

Advanced optical blade tip clearance measurement system

An advanced electro-optical system was developed to measure single blade tip clearances and average blade tip clearances between a rotor and its gas path seal in an operating gas turbine engine. This system is applicable to fan, compressor, and turbine blade tip clearance measurement requirements, and the system probe is particularly suitable for operation in the extreme turbine environment. A study of optical properties of blade tips was conducted to establish measurement system application limitations. A series of laboratory tests was conducted to determine the measurement system's operational performance characteristics and to demonstrate system capability under simulated operating gas turbine environmental conditions. Operational and environmental performance test data are presented.

Ford, M. J.↗
NASA NTRS1978

Feasibility of wing shielding of the airplane interior from the shock noise generated by supersonic tip speed propellers

A high tip speed turboprop is being considered as a future energy conservative airplane. The high tip speed of the propeller, combined with the speed of the airplane, results in supersonic relative flow on the propeller tips. These supersonic blade sections could generate noise that is a cabin environment problem. The feasibility of using wing shielding to lessen the impact of this supersonic propeller noise was investigated. An analytical model is chosen which considers that shock waves are associated with the propeller tip flow and indicates how they would be prevented from impinging on the airplane fuselage. An example calculation is performed where a swept wing is used to shield the fuselage from significant portions of the propeller shock waves.

Dittmar, J. H.↗
NASA NTRS1979

Tone Noise of Three Supersonic Helical Tip Speed Propellers in a Wind Tunnel

Three supersonic helical tip speed propellers were tested in the NASA Lewis 8- by 6-foot wind tunnel. This is a perforated-wall wind tunnel but it does not have acoustic damping material on its walls. The propellers were tested at tunnel through flow Mach numbers of 0.6, 0.7, 0.75, 0.8, and 0.85 with different rotational speeds and blade setting angles. The three propellers, which had approximately the same aerodynamic performance, incorporated different plan forms and different amounts of sweep and yielded different near field noise levels. The acoustically designed propeller had 45 deg of tip sweep and was significantly quieter at M = 0.8 cruise than the straight bladed propeller. The intermediate 30 deg tip sweep propeller, which was swept for aerodynamic purposes, exhibited noise that was between the other two propellers. Noise trends with varying helical tip Mach number and blade loading were also observed.

Dittmar, J. H.↗
NASA NTRS1979

An experimental investigation of the effect of rotor tip shape on helicopter blade-slap noise

The effect of tip-shape modification on blade-vortex interaction-induced helicopter blade-slap noise was investigated. The general rotor model system (GRMS) with a 3.148 m (10.33 ft) diameter, four-bladed fully articulated rotor was installed in the Langley V/STOL wind tunnel. The tunnel was operated in the open-throat configuration with treatment to improve the semi-anechoic characteristics of the test chamber. Based on previous investigation, four promising tips (ogee, sub-wing, 60 deg swept-tapered, and end-plate) were used along with a standard square tip as a baseline configuration. Aerodynamic and acoustical data concerning the relative applicability of the various tip configurations for blade-slap noise reduction are presented without analysis or discussion.

Hoad, D. R.↗
NASA NTRS1979

Tone noise of three supersonic helical tip speed propellers in a wind tunnel

Three eight bladed supersonic helical tip speed propellers were tested in the NASA Lewis Wind Tunnel at through flow Mach numbers of 0.6, 0.7, 0.75, 0.8, and 0.85. Such propellers are being considered as propulsors for a future energy conservative aircraft. The three propellers of equal performance, incorporate different plan forms and different amounts of sweep in order to investigate their noise generation, which could cause a cabin environment problem. The acoustically designed propeller SR-3 had 45 deg of tip sweep and was significantly quieter at Mach 0.8 cruise than the straight bladed propeller, SR-2. An intermediate 30 deg tip sweep propeller, SR-1m exhibited a noise level between the other two. Enhanced pressure-time traces indicated that SR-2 and SR-1m exhibited shock-like pressure traces at Mach-0.8 cruise while the SR-3 did not. Noise trends with varying helical tip Mach number and blade loading were also observed.

Dittmar, J. H.↗