Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrust Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

A parametric study of scramjet combustors for Mach 8 to Mach 20 flight

Performance trends for a combustor with ramp and slot fuel injectors are investigated through a three-dimensional parametric study at flight Mach numbers of 8, 10, 12, 16, and 20. Focus is placed on the mixing (combustion) efficiency, combustor loads, and thrust over the Mach number range. It is observed that the mixing efficiency decreases by 0.2 when a flight Mach number is increased from 8 to 12 but changes little for higher Mach numbers; the lower mixing is attributed more to a large decrease in the fuel-to-air velocity ratio and residence time over the Mach number range than to compressibility. It is pointed out that the ramp generates a shock impinging on the cowl, while a combined ramp and slot injection produces better mixing, both because of the action of this shock on the slot fuel and because of better fuel distribution in the duct.

Kamath, Pradeep S.↗
NASA NTRS1991

Experimental and computational studies of hovering rotor flows

HELIX-I, an essentially standard full-potential CFD helicopter rotor code, is unique in its use of the Clebisch kinematical flow description to specify a freely convecting wake and its capacity for predicting hover performance. A study is presently performed to assess the method's sensitivity to grids and solution-starting techniques. The effects of these parameters on thrust, power, load distribution, and wake geometry are ascertained and compared with an extensive rotor data base. The use of a fairly accurate starting solution yields no obvious advantage over the use of a novel starting method which employs a succession of diminishing artificial flows.

Nsi Mba, M.↗
NASA NTRS2000

Performance Optimization of a Rotor Alone Nacelle for Acoustic Fan Testing

This paper describes the techniques, equipment, and results from the optimization of a two-axis traverse actuation system used to maintain concentricity between a sting-mounted fan and a wall-mounted nacelle in the 9 x 15 (9 Foot by 15 Foot Test Section) Low Speed Wind Tunnel (LSWT) at the NASA Glenn Research Center (GRC). The Rotor Alone Nacelle (RAN) system, developed at GRC by the Engineering Design and Analysis Division (EDAD) and the Acoustics Branch, used nacelle-mounted lasers and an automated control system to maintain concentricity as thermal and thrust operating loads displace the fan relative to the nacelle. This effort was critical to ensuring rig/facility safety and experimental consistency of the acoustic data from a statorless, externally supported nacelle configuration. Although the tip clearances were originally predicted to be about 0.020 in. at maximum rotor (fan) operating speed, proximity probe measurements showed that the nominal clearance was less than 0.004 in. As a result, the system was optimized through control-loop modifications, active laser cooling, data filtering and averaging, and the development of strict operational procedures. The resultant concentricity error of RAN was reduced to +/- 0.0031 in. in the Y-direction (horizontal) and +0.0035 in./-0.001 3 in. in the Z-direction (vertical), as determined by error analysis and experimental results. Based on the success of this project, the RAN system will be transitioned to other wind tunnel research programs at NASA GRC.

Cunningham, C. C.↗
NASA NTRS2007

Conceptual Design and Feasibility of Foil Bearings for Rotorcraft Engines: Hot Core Bearings

Recent developments in gas foil bearing technology have led to numerous advanced high-speed rotating system concepts, many of which have become either commercial products or experimental test articles. Examples include oil-free microturbines, motors, generators and turbochargers. The driving forces for integrating gas foil bearings into these high-speed systems are the benefits promised by removing the oil lubrication system. Elimination of the oil system leads to reduced emissions, increased reliability, and decreased maintenance costs. Another benefit is reduced power plant weight. For rotorcraft applications, this would be a major advantage, as every pound removed from the propulsion system results in a payload benefit.. Implementing foil gas bearings throughout a rotorcraft gas turbine engine is an important long-term goal that requires overcoming numerous technological hurdles. Adequate thrust bearing load capacity and potentially large gearbox applied radial loads are among them. However, by replacing the turbine end, or hot section, rolling element bearing with a gas foil bearing many of the above benefits can be realized. To this end, engine manufacturers are beginning to explore the possibilities of hot section gas foil bearings in propulsion engines. This overview presents a logical follow-on activity by analyzing a conceptual rotorcraft engine to determine the feasibility of a foil bearing supported core. Using a combination of rotordynamic analyses and a load capacity model, it is shown to be reasonable to consider a gas foil bearing core section. In addition, system level foil bearing testing capabilities at NASA Glenn Research Center are presented along with analysis work being conducted under NRA Cooperative Agreements.

Howard, Samuel A.↗
NASA NTRS2008

Preliminary Analysis for an Optimized Oil-Free Rotorcraft Engine Concept

Recent developments in gas foil bearing technology have led to numerous advanced high-speed rotating system concepts, many of which have become either commercial products or experimental test articles. Examples include Oil-Free microturbines, motors, generators and turbochargers. The driving forces for integrating gas foil bearings into these high-speed systems are the benefits promised by removing the oil lubrication system. Elimination of the oil system leads to reduced emissions, increased reliability, and decreased maintenance costs. Another benefit is reduced power plant weight. For rotorcraft applications, this would be a major advantage, as every pound removed from the propulsion system results in a payload benefit. Implementing foil gas bearings throughout a rotorcraft gas turbine engine is an important long-term goal that requires overcoming numerous technological hurdles. Adequate thrust bearing load capacity and potentially large gearbox applied radial loads are among them. However, by replacing the turbine end, or hot section, rolling element bearing with a gas foil bearing many of the above benefits can be realized. To this end, engine manufacturers are beginning to explore the possibilities of hot section gas foil bearings in propulsion engines. This paper presents a logical follow-on activity by analyzing a conceptual rotorcraft engine to determine the feasibility of a foil bearing supported core. Using a combination of rotordynamic analyses and a load capacity model, it is shown to be reasonable to consider a gas foil bearing core section.

Howard, Samuel A.↗
NASA NTRS2024

Considerations for Thrust Vector Control (TVC) In-Flight Load Predictions

This presentation communicates an overview of a methodology developed by the National Aeronautics and Space Administration (NASA) Marshall Space Flight Center (MSFC) Thrust Vector Control (TVC) Systems Integration & Components Branch (MSFC-ER63). The methodology is based on NASA heritage TVC design practices and is designed to analyze the summation of static and quasi-static environments acting on a gimbaled rocket engine/motor system. The analysis determines the maximum overall expected induced torque acting on the rocket engine/motor system about the gimbal center of rotation and assumes a mathematical 3-Dimensional (3D) 2-Degree-of-Freedom (DOF) rigid-body pendulum model over a predefined range of angular motion. Additionally, it calculates the associated reaction force acting along a TVC actuator line-of-action (LOA) to maintain thrust vector holding operations. This methodology is particularly useful for determining maximum overall design loads for TVC actuator design-space shaping and requirements determination.

Thrust Vector Control↗
NASA NTRS1973

The preliminary design of bearings for the control system of a high-temperature lithium-cooled nuclear reactor

The design of bearings for the control system of a fast reactor concept is presented. The bearings are required to operate at temperatures up to 2200 F in one of two fluids, lithium or argon. Basic bearing types are the same regardless of the fluid. Crowned cylindrical journals were selected for radially loaded bearings and modified spherical bearings were selected for bearings under combined thrust and radial loads. Graphite and aluminum oxide are the materials selected for the argon atmosphere bearings while cermet compositions (carbides or nitrides bonded with refractory metals) were selected for the lithium lubricated bearings. Mounting of components is by shrink fit or by axial clamping utilizing differential thermal expansion.

Yacobucci, H. G.↗
NASA NTRS1981

Effect of simulated in-flight thrust reversing on vertical-tail loads of F-18 and F-15 airplane models

Investigations were conducted in the Langley 16-Foot Transonic Tunnel to provide data on a 0.10-scale model of the prototype F-18 airplane and a 0.047-scale model of the F-15 three-surface configuration (canard, wing, and horizontal tails). Test data were obtained at static conditions and at Mach numbers from 0.6 to 1.2 over an angle-of-attack range from 2 deg to 15 deg. Nozzle pressure ratio was varied from jet off to about 8.0.

Bare, E. A.↗
NASA NTRS2011

Pulsed Electric Propulsion Thrust Stand Calibration Method

The evaluation of the performance of any propulsion device requires the accurate measurement of thrust. While chemical rocket thrust is typically measured using a load cell, the low thrust levels associated with electric propulsion (EP) systems necessitate the use of much more sensitive measurement techniques. The design and development of electric propulsion thrust stands that employ a conventional hanging pendulum arm connected to a balance mechanism consisting of a secondary arm and variable linkage have been reported in recent publications by Polzin et al. These works focused on performing steady-state thrust measurements and employed a static analysis of the thrust stand response. In the present work, we present a calibration method and data that will permit pulsed thrust measurements using the Variable Amplitude Hanging Pendulum with Extended Range (VAHPER) thrust stand. Pulsed thrust measurements are challenging in general because the pulsed thrust (impulse bit) occurs over a short timescale (typically 1 micros to 1 millisecond) and cannot be resolved directly. Consequently, the imparted impulse bit must be inferred through observation of the change in thrust stand motion effected by the pulse. Pulsed thrust measurements have typically only consisted of single-shot operation. In the present work, we discuss repetition-rate pulsed thruster operation and describe a method to perform these measurements. The thrust stand response can be modeled as a spring-mass-damper system with a repetitive delta forcing function to represent the impulsive action of the thruster.

Wong, Andrea R.↗
NASA NTRS1998

Bulk-Flow Analysis of Hybrid Thrust Bearings for Advanced Cryogenic Turbopumps

A bulk-flow analysis and computer program for prediction of the static load performance and dynamic force coefficients of angled injection, orifice-compensated hydrostatic/hydrodynamic thrust bearings have been completed. The product of the research is an efficient computational tool for the design of high-speed thrust bearings for cryogenic fluid turbopumps. The study addresses the needs of a growing technology that requires of reliable fluid film bearings to provide the maximum operating life with optimum controllable rotordynamic characteristics at the lowest cost. The motion of a cryogenic fluid on the thin film lands of a thrust bearing is governed by a set of bulk-flow mass and momentum conservation and energy transport equations. Mass flow conservation and a simple model for momentum transport within the hydrostatic bearing recesses are also accounted for. The bulk-flow model includes flow turbulence with fluid inertia advection, Coriolis and centrifugal acceleration effects on the bearing recesses and film lands. The cryogenic fluid properties are obtained from realistic thermophysical equations of state. Turbulent bulk-flow shear parameters are based on Hirs' model with Moody's friction factor equations allowing a simple simulation for machined bearing surface roughness. A perturbation analysis leads to zeroth-order nonlinear equations governing the fluid flow for the thrust bearing operating at a static equilibrium position, and first-order linear equations describing the perturbed fluid flow for small amplitude shaft motions in the axial direction. Numerical solution to the zeroth-order flow field equations renders the bearing flow rate, thrust load, drag torque and power dissipation. Solution to the first-order equations determines the axial stiffness, damping and inertia force coefficients. The computational method uses well established algorithms and generic subprograms available from prior developments. The Fortran9O computer program hydrothrust runs on a Windows 95/NT personal computer. The program, help files and examples are licensed by Texas A&M University Technology License Office. The study of the static and dynamic performance of two hydrostatic/hydrodynamic bearings demonstrates the importance of centrifugal and advection fluid inertia effects for operation at high rotational speeds. The first example considers a conceptual hydrostatic thrust bearing for an advanced liquid hydrogen turbopump operating at 170,000 rpm. The large axial stiffness and damping coefficients of the bearing should provide accurate control and axial positioning of the turbopump and also allow for unshrouded impellers, therefore increasing the overall pump efficiency. The second bearing uses a refrigerant R134a, and its application in oil-free air conditioning compressors is of great technological importance and commercial value. The computed predictions reveal that the LH2 bearing load capacity and flow rate increase with the recess pressure (i.e. increasing orifice diameters). The bearing axial stiffness has a maximum for a recess pressure rati of approx. 0.55. while the axial damping coefficient decreases as the recess pressure ratio increases. The computer results from three flow models are compared. These models are a) inertialess, b) fluid inertia at recess edges only, and c) full fluid inertia at both recess edges and film lands. The full inertia model shows the lowest flow rates, axial load capacity and stiffness coefficient but on the other hand renders the largest damping coefficients and inertia coefficients. The most important findings are related to the reduction of the outflow through the inner radius and the appearance of subambient pressures. The performance of the refrigerant hybrid thrust bearing is evaluated at two operating speeds and pressure drops. The computed results are presented in dimensionless form to evidence consistent trends in the bearing performance characteristics. As the applied axial load increases, the bearing film thickness and flow rate decrease while the recess pressure increases. The axial stiffness coefficient shows a maximum for a certain intermediate load while the damping coefficient steadily increases. The computed results evidence the paramount of centrifugal fluid inertia at low recess pressures (i.e. low loads), and where there is actually an inflow through the bearing inner diameter, accompanied by subambient pressures just downstream of the bearing recess edge. These results are solely due to centrifugal fluid inertia and advection transport effects. Recommendations include the extension of the computer program to handle flexure pivot tilting pad hybrid bearings and the ability to calculate moment coefficients for shaft angular misalignments.

SanAndres, Luis↗
NASA NTRS1978

Dynamics of gas-thrust bearings

Computer program calculates load coefficients, up to third harmonic, for hydrostatic gas thrust bearings. Program is useful in identification of industrial situations where gas-thrust bearings have potential applications.

Stiffler, A. K.↗
NASA NTRS2022

Conceptual Design of a Tiltduct Reference Vehicle for Urban Air Mobility

NASA is establishing a fleet of conceptual air vehicle designs to support research and development for Urban Air Mobility (UAM). This fleet of vehicles will enable examination of the sensitivity of UAM vehicle designs to technology assumptions, identify key research and development needs for UAM aircraft, and provide the UAM community with reference vehicles that are publicly available and based upon known assumptions. To date, five six-passenger UAM reference vehicles have been published: a single-main-rotor helicopter, a side-by-side helicopter, a quadrotor, a lift-plus-cruise, and a tiltwing. To increase the breadth of vehicle technologies encapsulated in the fleet of NASA UAM reference vehicles, this paper establishes a tiltduct vehicle as an addition to the fleet. The fleet will continue to evolve as future analyses and trade studies are performed. The tiltduct UAM reference vehicle has six tilting ducted proprotors. This paper describes the initial configuration downselection; discusses ducted proprotor design rules of thumb as they applied to the conceptual design of the reference vehicle; describes the vehicle sizing, trade studies, and tuning of models performed; and finally, compares the resulting tiltduct vehicle against the other six-passenger NASA UAM reference vehicles. The high-level analyses performed for this study did not indicate significant differences in performance between the tiltduct and tiltwing reference vehicles, and so vehicle performance alone may not be a key driver in the selection of a tiltduct vehicle over a tiltwing vehicle. However, if ducts are found to have significant acoustical benefits, then acoustical priorities may provide a compelling reason to incorporate ducted proprotors. One significant limitation of the design presented in this paper is that the ducted proprotor performance was tuned based upon performance characteristics observed during historical tests with disk loadings (defined as thrust divided by proprotor disk area) of 125-250 lb/ft$^2$. The tiltduct vehicle designed in this study has a disk loading of 30 lb/ft$^2$, to be more representative of UAM vehicles; further studies to understand performance of ducted proprotors at representative disk loadings are warranted.

Tiltduct↗
NASA NTRS1981

Effect of time-dependent flight loads on turbofan engine performance deterioration

An analytic evaluation of the dynamic effects of two flight load conditions of the JT9D-7/747 propulsion system is conducted. Predicted performance changes associated with a once-per-flight vertical gust and a typical revenue service landing are calculated. The predicted dynamic load effects on thrust specific fuel consumption are found to be negligible. The results indicate that the quasi-steady state approach to flight loads modeling is adequate to investigate the factors important to the deterioration process.

Lewis, B. L.↗
NASA NTRSDate not supplied

Conceptual Design of a Tiltduct Reference Vehicle for Urban Air Mobility

NASA is establishing a fleet of conceptual air vehicle designs to support research and development for Urban Air Mobility (UAM). This fleet of vehicles will enable examination of the sensitivity of UAM vehicle designs to technology assumptions, identify key research and development needs for UAM aircraft, and provide the UAM community with reference vehicles that are publicly available and based upon known assumptions. To date, five six-passenger reference vehicles have been published: a quadrotor, a side-by-side, a lift-plus-cruise, a single-main-rotor helicopter, and a tiltwing. To increase the breadth of vehicle technologies encapsulated in the fleet of NASA UAM reference vehicles, this paper establishes a tiltduct vehicle as an addition to the fleet. The fleet will continue to evolve as future analyses and trade studies are performed. The tiltduct reference vehicle has six tilting ducted proprotors. This paper describes the initial configuration downselection; discusses ducted proprotor design rules of thumb as they applied to the conceptual design of the reference vehicle; describes the vehicle sizing, trade studies, and tuning of models performed; and finally, compares the resulting tiltduct vehicle against the other six-passenger NASA UAM reference vehicles. The high-level analyses performed for this study did not indicate significant differences in performance between the tiltduct and tiltwing reference vehicles, and so vehicle performance alone may not be a key driver in the selection of a tiltduct vehicle over a tiltwing vehicle. However, if ducts are found to have significant acoustical benefits, then acoustical priorities may provide a compelling reason to incorporate ducted proprotors. One significant limitation of the design presented in this paper is that the ducted proprotor performance was tuned based upon performance characteristics observed during historical tests with disk loadings (defined as thrust divided by proprotor disk area) of 125-250 lb/ft^2. The tiltduct vehicle designed in this study has a disk loading of 30 lb/ft^2, to be more representative of UAM vehicles; further studies to understand performance of ducted proprotors at representative disk loadings are warranted.

Tiltduct↗
DOE OSTI2025

Status Update for the Bearing Test Article Design Development – FY2025

Argonne National Laboratory’s (ANL) Mechanism Engineering Test Loop (METL) team has completed the design of a new Bearing Test Article (BTA) to test mechanical bearings for sodium fast reactor (SFR) mechanism applications. Recognition of the need for further bearing testing arose due to failure of rolling element bearings during testing of components for in-vessel fuel handling machines (FHMs) conducted at ANL in the METL facility. While the initial concept of the BTA arose from a need for bearing testing for FHM applications, the BTA design is configurable to test bearings of various sizes, types, and materials submerged in liquid sodium. Requirements for loading, shaft speed, temperature, and bearing size range were chosen based on requirements for SFR fuel handling. Modular components in the test bearing housings and shaft sleeves allow the design to accommodate a wide range of bearing sizes without modification to the larger assembly. Loading will be applied with screw jacks on the air side of the test article that will be adjusted to apply radial, thrust, or combined loading conditions. Applied force will be measured by load cells in-line with the loading mechanisms. In FY25 we have completed the design of the test article that will be fabricated and undergo testing at the METL facility. Drawing packages for the fabrication of the test article have been drafted and are being reviewed to add part tolerances and we have started ordering off-the-shelf components. The report will summarize the development of the Bearing Test Article design starting with an overview of the entire test article, then a more detailed examination of the bearing test section, loading mechanisms, test article ports and seals, and support structures, including analysis that went into significant design choices.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗