Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRIBOLOGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Structure and Tribological Properties of CrTiAlCN Coatings with Various Carbon Contents

Multi-component CrTiAlCN coatings with different carbon contents were deposited on AISI M2 high-speed steels using unbalanced magnetron sputtering via adjusting the C{sub 2}H{sub 2} flow rates, and their microstructures and mechanical properties were characterized by using SEM, EDS, XRD, Vickers hardness tester and scratch tester, respectively. The tribological properties of CrTiAlCN coatings sliding against SUS440C high carbon martensitic balls were performed using ball-on-disk tribo-tester. The results showed that CrTiAlCN coatings were mainly comprised of (111) and (200) crystal orientation. The maximum hardness of coatings was 29.4 ± 1.5 GPa as the carbon content was 22.5 at.%. With an increase in the carbon content of coatings, the friction coefficients and wear rates of CrTiAlCN/SUS440C tribo-pairs were significantly reduced, and the wear mechanism of coatings changed from adhesive wear to abrasive wear.

36 MATERIALS SCIENCE↗

A Comparative Study on Microstructure, Mechanical and Tribological Properties of A4, AE41, AS41 and AJ41 Magnesium Alloys

Microstructure, tensile and wear properties of as-cast A4 (Mg-4Al), AE41 (Mg-4Al-0.5Ce-0.5La), AS41 (Mg-4Al-1Si) and AJ41 (Mg-4Al-1Sr) alloys were investigated, and the results were compared with each other in this study. Microstructures were investigated by XRD, optical and scanning electron microscopes. Tensile tests were conducted at both room and elevated temperatures. Tribological properties were examined by pin-on-disk wear tests under different applied loads. Microstructure characterizations revealed that the volume fraction of second phases considerably increased by alloying additions of 1 wt.% Ce/La, Si and Sr. The microstructure of A4 alloy consisted of α-Mg grains and divorced β-Mg{sub 17}Al{sub 12} phases. After individual alloying additions of 1 wt.% Ce/La, Si and Sr, the secondary phases were primarily replaced by needle-shaped and massive blocky-shaped Al{sub 11}(Ce,La){sub 3} phases in AE41 alloy, Chinese-script-type Mg{sub 2}Si phases in AS41 alloy and divorced globular-like and massive blocky-shaped Al{sub 4}Sr and (Mg,Al){sub 17}Sr{sub 2} phases in AJ41 alloy. The tensile tests showed that at both room and elevated temperatures alloying additions of 1 wt.% Ce/La, Si and Sr resulted in an increase in the strength but a decrease in the ductility. Among the studied alloys, AS41 alloy exhibited the best strength. Wear test results showed that AE41 and AJ41 alloys similarly exhibited the best wear resistance owing to the presence of hard and dense intermetallics. Abrasion was the main wear mechanism under low applied loads while delamination, adhesion and oxidation mechanisms were majorly observed under high applied loads.

36 MATERIALS SCIENCE↗

A Synergetic Effect of Silver and Carbon Nanotubes on the Tribological Behavior of TiAl-Based Composites

This work explores the addition of silver and multiwalled carbon nanotubes (MWCNTs) for acquiring a better tribological property at the lowest cost. The friction and wear behavior of TiAl-Ag-MWCNTs at 0-160 min is estimated on a HT-1000 ball-on-disk tribometer. The friction coefficients and wear rates of TAMs-E at 0-160 min are smaller than those of TAMs-D and TAMs-F. At 0-20 min, the MWCNTs are pulled out from a TAMs-E to be exposed on the wear scar, and then, they are well combined with silver. For accumulation of silver, it is helpful to form a lubrication film to achieve a decrease of 4.51-1.63 × 10{sup −4} mm{sup 3} N{sup −1} m{sup −1} in wear rate and a reduction of 0.37-0.24 in friction coefficient. The lubrication film at 20-160 min can accomplish low friction and low wear. Close to 0.5 wt.%MWCNTs and 7.5 wt.%Ag are used in this study for small values of 0.19-0.26 in friction coefficient and 2.36-4.43 × 10{sup −4} mm{sup 3} N{sup −1} m{sup −1} in wear rate. It jointly satisfies the lowest cost for the fabrication of TiAl-based composites.

36 MATERIALS SCIENCE↗

Tribological properties of PDA + PTFE coating in oil-lubricated condition

In this work the tribological properties of 45 ± 2 μm-thick polytetrafluoroethylene (PTFE) and polydopamine (PDA) + PTFE coatings in oil-lubricated conditions were investigated under a normal load of 10 N and a linear reciprocating speed of 0.1 m/s. Both the PTFE and the PDA + PTFE coatings were deposited using an in-house spray-coating method. The PDA + PTFE coating was five times more durable compared to the PTFE coating in oil-lubricated conditions. Both PTFE and PDA + PTFE coatings showed lower COF in oil-lubricated conditions than in dry conditions. The nanomechanical properties measured by PeakForce Quantitative Nanomechanical (PFQNM) characterization method showed an increase in Young’s modulus and adhesion force for the PDA + PTFE coatings compared to the PTFE coatings. Chemical analysis showed that the cross-linking between PDA and PTFE polymer chains occurred during the high-temperature sintering procedure. Finally, the higher adhesion of PDA + PTFE coating to the cast iron substrate and the stronger cohesion due to the cross-linking between PDA and PTFE contributed to the higher durability of the PDA + PTFE composite coatings.

36 MATERIALS SCIENCE↗

A novel fiber-fretting test for tribological characterization of the fiber/matrix interface

Ceramic matrix composites exhibit excellent high temperature properties and are candidate materials for structural applications from jet engines to nuclear fuel cladding. The strength and deformation behavior of these composites are intrinsically tied to the properties of the fiber/matrix interface. This research introduces a novel technique to evaluate the fundamental friction and wear characteristics of these interfaces. A case study on SiC f /PyC/SiC m composites applies in situ fiber fretting to investigate the kinetic friction coefficient and cyclic wear characteristics of the interphase. The experimental methodology is presented in explicit detail to encourage other researchers to explore the capabilities of this technique. Additionally, testing was carried out as a function of fiber roughness, PyC thickness (≈10, 500, 1200 nm), cycle count (10, 100, 1000), and frequency (1, 5, and 10 Hz). The friction coefficient and wear behavior changed with cycle length due to a transition from adhesive to abrasive mechanisms. SEM fractography provided insights to tribological evolution from adhesive sliding to three-body abrasive wear. The structural disorder at the tribo-surface relating to graphitic content and dangling bond density was investigated using Raman spectroscopy. Properties are contextualized with comparison to uniaxial tensile behavior of the parent composite.

36 MATERIALS SCIENCE↗

Effect of equal channel angular pressing on the mechanical and tribological behavior of Al-Zn-Mg-Cu alloy

Highlights: • The correlation of microstructure, mechanical and wear properties has been studied. • The correlation between tensile properties and shear properties has been also studied. • Mechanical and tribological properties have been improved through the ECAP process of the Al-7075 alloy. • The dominant wear mechanisms in the initial material were adhesive and oxidative wear as well as delamination. • Abrasive and oxidative wear were the dominant wear mechanisms in ECAP processed specimens. - Abstract: Microstructure, mechanical properties and wear behavior of severely deformed Al-7075 alloy by equal channel angular pressing (ECAP) were studied. Microhardness, tensile and shear strength tests were performed to evaluate the mechanical properties of the material. The relationship between tensile and shear strength was also extracted. In addition, with the aim of study the wear behavior, the wear tests were performed by using a pin-on-disk machine under different normal loads. The microscopic observations i.e. transmission electron microscopy (TEM) and scanning electron microscope (SEM), were used to analyze the microstructure of specimens as well as the surface, subsurface and debris of worn specimens. Mechanical properties results showed that the hardness and strength (tensile and shear) of the ECAP-processed alloy were higher than that of the annealed alloy and increased with the increment of pass number. The wear test data revealed that the wear rate and friction coefficient decreased with increasing ECAP passes. The SEM analysis of worn specimens demonstrated that the dominant wear mechanisms of the annealed alloy were adhesion wear and delamination and the dominant wear mechanisms of ECAP processed alloy were abrasive wear and plowing bands. Oxidative wear was also observed at both annealed and ECAPed alloy. Totally, these results demonstrated that ultrafine-grained structure fabricated by ECAP, improves the wear resistance of the Al-7075 alloy.

36 MATERIALS SCIENCE↗

Tribological properties of metal doped a-C film by RF magnetron sputtering method

We deposited various metal doped amorphous carbon (a-C:Me) films by radio frequency (RF) magnetron co-sputtering method. Tungsten (W), molybdenum (Mo), and chromium (Cr) were used as the doping metals in a-C film. The applied power on carbon and metal (W, Mo, and Cr) target were 150 W and 40 W, respectively. a-C:Me films exhibited smooth and uniform surface roughness and the hardness over 15 GPa. Specially, a-C:W film showed the maximum hardness of 18.5 GPa. The coefficient of friction of a-C:W film is relatively lower than that of other films and the critical load value of a-C:W film is higher. These results are related to the concentration of metal in the carbon matrix by the difference of sputtering yield and the change of the structure by the metal bonding. Consequently, W metal is good candidate as the doping metal for the improvement of tribological characteristics.

36 MATERIALS SCIENCE↗

Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power

Molten salts are considered as candidate heat transfer fluids and thermal energy storage media for next generation concentrating solar power (CSP). A molten salt circulates inside the piping and heat exchanger and also functions as a lubricant for the sleeve bearings of the CSP pump. Furthermore, wear- and corrosion-resistant high-temperature bearing materials are critical for the pump efficiency and durability. This study evaluated the tribological performance of candidate bearing materials in lubrication of a molten chloride salt mixture (20% NaCl + 40% MgCl 2 + 40% KCl) at 750 °C in an inert argon gas (a simulative CSP pump environment). Six ceramic-alloy pairs were tested, zirconia and silicon nitride against Haynes 244, Hastelloy C276, and Tribaloy T900 alloy, and ranked by the friction coefficient and wear loss. Characterization of worn surfaces suggested the wear mechanism as a combination of abrasion, adhesion, and tribocorrosion. Results from this study provide fundamental insight for the development and selection of bearing materials for molten salt powered CSP pumps.

14 SOLAR ENERGY↗

Post weld heat treatment and operating temperature effect on tribological behavior of laser cladded stellite 21 coating

This study intends to investigate the feasibility of using laser cladding as a potential process to repair hot working tools by a hardfacing process. A Stellite 21 alloy coating was printed on a 350 maraging steel via laser cladding and the coating microstructure and tribological performance were characterized in as printed conditions and after heat treatment. Such a laser-processed coating showed a high integrity with little porosity and good bonding with the substrate. The Stellite coating produced substantially lower friction and a smoother contact area but had inferior wear resistance compared with the maraging steel substrate. Post process heat treatment at 650 °C for 20 h led to significant amount of strain-induced FCC to HCP phase transformation but had little improvement in wear resistance. Detailed materials characterization using X-ray diffraction and electron microscopy provided fundamental insights to the underlying mechanisms. This study opens the door for future R&D for tool surface repair by laser cladding.

36 MATERIALS SCIENCE↗

Investigating Alkylsilane Monolayer Tribology at a Single-Asperity Contact with Molecular Dynamics Simulation

Chemisorbed monolayer films are known to possess favorable characteristics for nanoscale lubrication of micro- and nanoelectromechanical systems (MEMS/NEMS). Prior studies have shown that the friction observed for monolayer-coated surfaces features a strong dependence on the geometry of contact. Specifically, tip-like geometries have been shown to penetrate into monolayer films, inducing defects in the monolayer chains and leading to plowing mechanisms during shear, which result in higher coefficients of friction (COF) than those observed for planar geometries. In this work, we use molecular dynamics simulations to examine the tribology of model silica single-asperity contacts under shear with monolayer-coated substrates featuring various film densities. It is observed that lower monolayer densities lead to reduced COFs, in contrast to results for planar systems where COF is found to be nearly independent of monolayer density. This is attributed to a liquid-like response to shear, whereby fewer defects are imparted in monolayer chains from the asperity, and chains are easily displaced by the tip as a result of the higher free volume. This transition in the mechanism of molecular plowing suggests that liquid-like films should provide favorable lubrication at single-asperity contacts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phosphonium-Organophosphate Ionic Liquids as Lubricant Additives: Effects of Cation Structure on Physicochemical and Tribological Characteristics

In our previous work we suggest great potential for a phosphonium-organophosphate ionic liquid (IL) as an antiwear lubricant additive. In this study, a set of five ILs were carefully designed and synthesized, with identical organophosphate anions but dissimilar phosphonium cations, to allow systematic investigation of the effects of cation alkyl chain length and symmetry on physicochemical and tribological properties. Symmetric cations with shorter alkyl chains seem to increase the density and thermal stability due to closer packing. On the other hand, either higher cation symmetry or longer alkyl moieties induce a higher viscosity, though the viscosity index is dependent more on molecular mass than on symmetry. While a larger cation size generally increases an IL’s solubility in nonpolar hydrocarbon oils, six-carbon seems to be the critical minimum alkyl chain length for high oil miscibility. Both the two ILs, that are mutually oil miscible, have demonstrated promising lubricating performance at 1.04% treat rate, though the symmetric-cation IL moderately outperformed the asymmetric-cation IL. Moreover, characterizations on the tribofilm formed by the best-performing symmetric-cation IL revealed the film thickness, nanostructure, and chemical composition. Our results provide fundamental insights for future molecular design in developing oil-soluble ILs as lubricant additives.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Adhesion of tungsten carbide reinforced amorphous hydrocarbon thin films (WC/a-C:H) to steel substrates for tribological applications

We have explored the adhesive interlayer structure for a tungsten carbide reinforced amorphous hydrocarbon thin film coating (WC/a-C:H) that demonstrated excellent coating adhesion under highly stressed tribological contact. Transmission electron microscopy (TEM) analysis including cross-sectional imaging, electron diffraction, and energy dispersive spectroscopy was performed on abrupt and gradient interfaces within the multilayer film architecture. Interpretation of these results is aided by quantum mechanical calculations that were performed to investigate bonding interactions of the Cr adhesive interlayer to the Fe substrate surface within a - 3 nm thick interfacial region. Low levels of oxygen present in the coating deposition chamber during deposition were found at the Fe-Cr interface using high-resolution TEM. Molecular orbital calculations for a linear three-atom molecular model Fe-O-Cr demonstrate the role of O in strengthening Fe to Cr bonding within that interfacial region.

36 MATERIALS SCIENCE↗

Impact of laser power density on tribological properties of Pulsed Laser Deposited DLC films

Fabrication of wear resistant and low friction carbon films on the engineered substrates is considered as a challenging task for expanding the applications of diamond-like carbon (DLC) films. In this paper, pulsed laser deposition (PLD) technique is used to deposit DLC films on two different types of technologically important class of substrates such as silicon and AISI 304 stainless steel. Laser power density is one of the important parameter used to tailor the fraction of sp{sup 2} bonded amorphous carbon (a-C) and tetrahedral amorphous carbon (ta-C) made by sp{sup 3} domain in the DLC film. The I(D)/I(G) ratio decreases with the increasing laser power density which is associated with decrease in fraction of a-C/ta-C ratio. The fraction of these chemical components is quantitatively analyzed by EELS which is well supported to the data obtained from the Raman spectroscopy. Tribological properties of the DLC are associated with chemical structure of the film. However, the super low value of friction coefficient 0.003 is obtained when the film is predominantly constituted by a-C and sp{sup 2} fraction which is embedded within the clusters of ta-C. Such a particular film with super low friction coefficient is measured while it was deposited on steel at low laser power density of 2 GW/cm{sup 2}. The super low friction mechanism is explained by low sliding resistance of a-C/sp{sup 2} and ta-C clusters. Combination of excellent physical and mechanical properties of wear resistance and super low friction coefficient of DLC films is desirable for engineering applications. Moreover, the high friction coefficient of DLC films deposited at 9GW/cm{sup 2} is related to widening of the intergrain distance caused by transformation from sp{sup 2} to sp{sup 3} hybridized structure.

36 MATERIALS SCIENCE↗

Microstructure and tribological performance of nanocomposite Ti-Si-C-N coatings deposited using hexamethyldisilazane precursor

Thick nanocomposite Ti-Si-C-N coatings (20-30 {mu}m) were deposited on Ti-6Al-4V substrate by magnetron sputtering of Ti in a gas mixture of Ar, N{sub 2}, and hexamethyldisilazane (HMDSN) under various deposition conditions. Microstructure and composition of the coatings were studied using scanning electron microscopy, x-ray diffraction, and energy dispersive x-ray spectroscopy, while the mechanical and tribological properties of these coatings were studied using Rc indentation, and micro- and nanoindentations, solid particle erosion testing, and ball-on-disk wear testing. It has been observed that the Si concentration of these coatings is varied from 0% (TiN) to 15% (Ti-Si-C-N), while the structure of these coatings is similar to the nanocomposite Ti-Si-N coatings and consists of nanocrystalline B1 structured Ti(C,N) in an amorphous matrix of SiC{sub x}N{sub y} with the grain size of 5->100 nm, depending on the coating preparation process. These coatings exhibit excellent adhesion when subjected to Rc indentation tests. The microhardness of these coatings varies from 1200 to 3400 HV25, while the nanohardness varies from 10 to 26 GPa. Both the microhardness and nanohardness are slightly lower than those of similar coatings prepared using trimethylsilane. However, the erosion test using a microsand erosion tester at both 30 deg. and 90 deg. incident angles shows that these coatings have very high erosion resistance and up to a few hundred times of improvement has been observed. These coatings also exhibit very high resistance to sliding wear with a low coefficient of friction of about 0.2 in dry sliding. There are a few advantages of using the HMDSN precursor to prepare the Ti-Si-C-N coatings over conventional magnetron sputtered deposition of Ti-Si-N coatings including composition uniformity, precursor handling safety, and high deposition rate. The coatings can be applied to protect gas turbine compressor blades from solid particle erosion and steam turbine blades from liquid droplet erosion, as well as other mechanical components that experience severe abrasion. These coatings may also be used in areas where both high wear resistance and low friction are required.

36 MATERIALS SCIENCE↗

Tribological behavior of Ti-Al-Si-C-N hard coatings deposited by hybrid arc-enhanced magnetron sputtering

Ti-Al-Si-C-N hard coatings are deposited on high speed steel by hybrid arc-enhanced magnetron sputtering, and the hardness, adhesion, and tribological behavior are studied. On account of the nanocomposite structure, the coatings possess hardness of more than 30 GPa. Failure of the coating during the scratch test is due to the buckling and wedge spallation failure mechanism. Compared to Ti-Al-Si-N, the presence of C in the Ti-Al-Si-C-N coatings leads to reduced friction coefficient and wear rate, indicating effective lubrication rendered by amorphous C. According to the wear tracks examined by scanning electron microscopy, the wear mechanism can be explained by plowing abrasion.

36 MATERIALS SCIENCE↗

Effect of microstructural evolution on mechanical and tribological properties of Ti-doped DLC films: How was an ultralow friction obtained?

This paper examined the evolution of microstructure and its effect on the mechanical and tribological properties of ultralow friction Ti-doped diamondlike carbon (DLC) films, by adjusting the CH{sub 4}/Ar ratio under constant radio frequency discharge power and bias. The Raman, high resolution transmission electron microscopy, atomic force microscope and nanoindentation measurements consistently reveal or indicate the formation of curved graphene sheets or fullerenelike nanostructures with increasing CH{sub 4}/Ar ratio. The superior frictional performance (0.008–0.01) of Ti-DLC films can be attributed to the special microstructure related to the development of embedded fullerenelike nanostructures as a result of incorporation of TiO{sub 2} clusters. The contributing factors include high hardness and cohesion, excellent toughness, high load-bearing capacity, as well as the ultralow shear resistance transform layer and the excellent antioxidation stability brought by the doped Ti.

36 MATERIALS SCIENCE↗

High Speed Tribology of the Head-Disk Interface by Computer Simulation Final Report CRADA No. TC-297-92-C

The purpose of this project is to develop and validate a molecular dynamics model of nanoscale tribological processes occurring inside the head-disk interface of magnetic recording devices. Within the three years of the project the partners will: write a new molecular dynamics computer simulation code for growth, sliding and impact inside the head-disk interface; identify accurate models for chemical bonding within coatings used to protect magnetic surfaces, especially amorphous carbon thin films; simulate the growth of amorphous carbon thin films and analyse the resulting chemical bonding; simulate friction and wear processes relevant to the head-disk interface; and validate the model through comparison with AFM and nanoindenter studies of friction and wear of amorphous carbon thin films.

36 MATERIALS SCIENCE↗

Tribological behavior of nuclear graphite in high-temperature inert environment

This report formally documents the completion of the Advanced Reactor Technologies Level 2 Milestone (M2AT-26OR0605058), “Complete initial wear/abrasion studies,” due June 1, 2026. The work presented in this report expend upon our previously published manuscript titled Sliding friction and wear behavior of nuclear graphite in high temperature inert environment: Influence of contact load, speed and temperature. The sliding friction and wear of self-mated ET-10 nuclear graphite were characterized across a range of elevated temperatures (650°C and 750°C), contact loads (20 N and 40 N), and sliding speeds (1 mm/s and 10 mm/s) within a controlled argon environment. Tribological data combined with advanced morphological characterization were used to provide a detailed mechanistic framework for the frictional and wear behavior of nuclear graphite in high-temperature inert conditions. Furthermore, the report evaluates the inherent limitations of bench-scale characterization and addresses the critical disparities between laboratory findings and the complex, in-service friction and wear behavior of fuel pebbles within a reactor environment.

36 MATERIALS SCIENCE↗