SEARCH · Engineering Papers
Results for “TEM”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Revealing the synergistic effects of sequential and simultaneous dual beam irradiations in tungsten via in-situ TEM
Elucidating the synergistic effects of different energetic beams on the radiation response of nuclear materials is critical for developing an improved methodology for their evaluation when exposed to extreme environments. This article describes in-situ sequential (He implantation followed by Kr irradiation and vice-versa) and simultaneous (heavy ion Kr irradiation and He implantation) dual beam irradiations performed on tungsten at 1223 K. Dislocation loop density, average area, and total loop damage as a function of irradiation history and dose/fluence are quantified. The loop Burgers vectors and cavity damage (cavity density, size and total change in volume) are also determined at the final maximum dose for each condition. The loop damage evolution was different in all cases, with the smallest loop damage observed in the simultaneous experiment. Annihilation of Kr generated dislocation loops during He implantation in the Kr + He experiment was an unanticipated observation that may be explained by the dynamic evolution of dislocation loop sink strengths and time-dependent defect fluxes. Dislocation loop raft formation, denuded zones near extended defects, and cavity damage are compared across the different conditions. The phenomena observed and discussed in this work will stimulate further experimental and computational modeling activities leading to improved fundamental understanding of the irradiation response of nuclear materials under reactor-similar environments.
Helium bubble nucleation and growth in alloy HT9 through the use of in situ TEM: Sequential he-implantation and heavy-ion irradiation versus dual-beam irradiation
The formation of He bubbles in Ferritic/Martensitic steel HT9 is investigated through the use of in situ Transmission Electron Microscopy coupled with He implantation and heavy ion irradiation. Of particular interest is the effect of increasing He appm/dpa ratio on the formation and growth of the bubbles, as well as the effect of the sequential order of ion irradiation i.e. He-pre-implantation followed by heavy-ion irradiation versus true dual-beam irradiation. Finally, the role of He is discussed.
TEM characterization of dislocation loops in proton irradiated single crystal ThO2
Not Available
Automated analysis of grain morphology in TEM images using convolutional neural network with CHAC algorithm
Not Available
Understanding and removing FIB artifacts in metallic TEM samples using flash electropolishing
Not Available
Creep properties of advanced austenitic steel 709 determined through short experiments under in-situ neutron diffraction followed by TEM characterization
Here in this study, the creep mechanisms at play in Alloy 709 (Fe-20Cr-25Ni) are investigated by performing short-term creep-type tests under in-situ neutron diffraction experiments. Short tests are performed in the temperature range of 500 to 900 °C under constant load with a load ranging from 50 to 150 MPa. The creep exponent and activation energy are determined using the Bird-Mukherjee-Dorn relation and compared to that obtained from conventional longer creep tests from the literature. Scanning transmission electron microscopy (S/TEM) of the post-creep microstructure indicates that interaction of dislocations with precipitates are a dominant mechanism at play. Furthermore, local elemental mapping indicated chemical segregation at grain boundaries and formation of complex precipitates.
In situ TEM observations of high-strain-rate deformation and fracture in pure copper
Not Available
Grain growth of nanocrystalline aluminum under tensile deformation: A combined in situ TEM and atomistic study
Nanocrystalline Al thin films have been strained in situ in a transmission electron microscope using two separate nanomechanical techniques involving a push-to-pull device and a microelectromechanical system (MEMS) device. Deformation-induced grain growth was observed to occur via stress-assisted grain boundary migration with extensive grain growth occurring in the necked region, indicating that the increase in local stress drives the boundary migration. Under applied tensile stresses close to the ultimate tensile strength of 450 MPa for a nanocrystalline Al specimen, measured boundary migration speeds are 0.2 – 0.7 nm s -1 for grains outside necked region and increases to 2.5 nm s -1 for grains within the necked region where the local estimated tensile stresses are elevated to around 630 MPa. By tracking grain boundary motion over time, molecular dynamics simulations showed qualitative agreement in terms of pronounced grain boundary migration with the experimental observations. The combined in situ observation and molecular dynamics simulation results underscore the important role of stress-driven grain growth in plastically deforming nanocrystalline metals, leading to intergranular fracture through predominant grain boundary sliding in regions with large localized deformation.
Precise measurement of activation parameters for individual dislocation nucleation during in situ TEM tensile testing of single crystal nickel
Not Available
Calibrating cryogenic temperature of TEM specimens using EELS
Cryogenic Scanning/Transmission Electron Microscopy has been established as a leading method to image sensitive biological samples and is now becoming a powerful tool to understand materials' behavior at low temperatures. However, achieving precise local temperature calibration at low temperatures remains a challenge, which is especially crucial for studying phase transitions and emergent physical properties in quantum materials. In this study, we employ electron energy loss spectroscopy (EELS) to measure local cryogenic specimen temperatures. Here we use the temperature-dependent characteristics of aluminum's bulk plasmon peak in EEL spectra, which shifts due to changes in electron density caused by thermal expansion and contraction. We successfully demonstrate the versatility of this method by calibrating different liquid nitrogen cooling holders in various microscopes, regardless of whether a monochromated or non-monochromated electron beam is used. Temperature discrepancies between the actual temperature and the setpoint temperatures are identified across a range from room temperature to 100 K. This work demonstrates the importance of temperature calibrations at intermediate temperatures and presents a straightforward, robust method for calibrating local temperatures of cryogenically-cooled specimens in electron microscopes.
Using in-situ TEM Triple Ion Beam Irradiations to Study the Effects of Deuterium, Helium, and Radiation Damage on TPBAR Components.
Abstract not provided.
In Situ TEM Investigation of the Spontaneous Hollowing of Alloy Anode Nanocrystals
Explore the source record for details and available documents.
In Situ TEM Investigation of Lithium Intercalation in Ti3C2TX MXenes for Energy Storage Applications
Explore the source record for details and available documents.
In-situ TEM laser heating for manipulation of cooling rates and observation of precipitate dissolution kinetics.
Abstract not provided.