Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structural components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Stress analysis and damage evaluation of flawed composite laminates by hybrid-numerical methods

Structural components in flight vehicles is often inherited flaws, such as microcracks, voids, holes, and delamination. These defects will degrade structures the same as that due to damages in service, such as impact, corrosion, and erosion. It is very important to know how a structural component can be useful and survive after these flaws and damages. To understand the behavior and limitation of these structural components researchers usually do experimental tests or theoretical analyses on structures with simulated flaws. However, neither approach has been completely successful. As Durelli states that 'Seldom does one method give a complete solution, with the most efficiency'. Examples of this principle is seen in photomechanics which additional strain-gage testing can only average stresses at locations of high concentration. On the other hand, theoretical analyses including numerical analyses are implemented with simplified assumptions which may not reflect actual boundary conditions. Hybrid-Numerical methods which combine photomechanics and numerical analysis have been used to correct this inefficiency since 1950's. But its application is limited until 1970's when modern computer codes became available. In recent years, researchers have enhanced the data obtained from photoelasticity, laser speckle, holography and moire' interferometry for input of finite element analysis on metals. Nevertheless, there is only few of literature being done on composite laminates. Therefore, this research is dedicated to this highly anisotropic material.

Yang, Yii-Ching↗
NASA NTRS1986

Greenstone belts: Their components and structure

Greenstone sucessions are defined as the nongranitoid component of granitoid-greenstone terrain and are linear to irregular in shape and where linear are termed belts. The chemical composition of greenstones is described. Also discussed are the continental environments of greenstone successions. The effects of contact with granitoids, geophysical properties, recumbent folds and late formation structures upon greenstones are examined. Large stratigraphy thicknesses are explained.

Vearncombe, J. R.↗
DOE OSTI2023

Initial Fracture Propagation Modeling of Graphite Components with Grizzly

Graphite has historically been extensively used in power reactor cores and will be used in multiple types of advanced reactors currently under development. These graphite structural components can experience significant stresses due to nonuniform volumetric strains induced by irradiation and thermal expansion, which can lead to fracture. Robust tools for predicting fracture initiation and propagation in graphite structural components in nuclear reactors are important for evaluating component integrity, developing design standards, and interpreting experimental results to characterize graphite performance. The U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation program has been developing degradation models for other structural components in nuclear reactors within the Grizzly and BlackBear codes. This report documents an effort to develop initial capabilities for modeling graphite fracture within these codes, building on prior efforts to model fracture in other materials. Major elements of this effort include developing a new system for modeling fracture nucleation and growth in two dimensions using the extended finite element method and incorporating a damage and plasticity model. These capabilities are applied here to model a representative graphite component and a splitting disc experiment used to obtain tensile strength.

36 MATERIALS SCIENCE↗
NASA NTRS2006

Bearing-Load Modeling and Analysis Study for Mechanically Connected Structures

Bearing-load response for a pin-loaded hole is studied within the context of two-dimensional finite element analyses. Pin-loaded-hole configurations are representative of mechanically connected structures, such as a stiffener fastened to a rib of an isogrid panel, that are idealized as part of a larger structural component. Within this context, the larger structural component may be idealized as a two-dimensional shell finite element model to identify load paths and high stress regions. Finite element modeling and analysis aspects of a pin-loaded hole are considered in the present paper including the use of linear and nonlinear springs to simulate the pin-bearing contact condition. Simulating pin-connected structures within a two-dimensional finite element analysis model using nonlinear spring or gap elements provides an effective way for accurate prediction of the local effective stress state and peak forces.

Knight, Norman F., Jr.↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbomachinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbopumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbomachinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test articles mimic a single inducer blade that is unwrapped from the hub, thus resembling a low aspect ratio cantilevered plate. To induce cavitation, the plates are oriented at a non-zero angle of attack and have rough strips near their leading edges. To control the extent of cavitation, the static pressure of the water tunnel is controlled between roughly 0.5 and 1.5 atm. A high-speed camera is used to quantify the coverage of the cavitations heet. The sheet coverage is then correlated to changes in fluid-added mass and hydroelstic damping. In addition, a corresponding two-way coupled CFD/FE model is under development for test/analysis correlation.

Ben Davis↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbomachinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbopumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbomachinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test article is a low aspect ratio cantilevered plate, thus mimicing a single inducer blade that is unwrapped from its hub. The test article is oriented at zero angle of attack and has a triangular trip at its leading edge to induce cavitation. To change the extent of cavitation, the static pressure of the water tunnel is controlled. A high-speed camera is used to quantify the coverage of the cavitation sheet.

Fluid-Structure Interaction↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbo machinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbo pumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbo machinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test article is a low aspect ratio cantilevered plate, thus mimicing a single inducer blade that is unwrapped from its hub. The test article is oriented at zero angle of attack and has a triangular trip at its leading edge to induce cavitation. To change the extent of cavitation, the static pressure of the water tunnel is controlled. A high-speed camera is used to quantify the coverage of the cavitation sheet.

Structural Dynamics↗
DOE OSTI2023

Deconvoluting Structures of Component Plant Biopolymers Using Deuterium Labeled Brassica oleracea Stems

Several Brassica species are cultivated globally for the production of seed oils as food, lubricants, and increasingly biofuels. The stem and leaf residues of these herbaceous dicotyledonous crops constitute another feedstock for biofuels and other products. Plant cell walls are complex, multipolymeric structures that consist primarily of polysaccharides and lignin. Cellulose chains coalesce to form crystalline microfibrils while the amorphous biopolymers, hemicellulose, and lignin form a network structure and fill the interstitial space. Neutron scattering has been used for the structural study of the assembly and deconstruction of the plant cell walls. However, similar neutron sensitivity of the different amorphous biopolymers has made structural association to individual component biopolymers nontrivial and ambiguous. To improve the association of structural features to specific biopolymer components, partial deuteration of the plant cell wall can be employed to increase the difference in the neutron scattering length density between amorphous carbohydrate and lignin plant polymers. Vegetative stems from partially deuterated Brassica oleracea acephala (kale) plants were obtained commercially, and the plant cell wall structures were studied by contrast-variation small-angle neutron scattering (CV-SANS) and Fourier-transform infrared spectroscopy (FTIR). FTIR results indicated that deuterium substitution for hydrogen in the carbohydrates was higher than that in lignin. By combining CV-SANS and FTIR results, the neutron scattering length density (nSLD) of the polysaccharides and lignin was determined to match nSLD of 65%:35% and 48%:52% D 2 O/H 2 O solvent mixtures, respectively. These nSLD values were higher than the nSLD values of polysaccharides and lignin for H 2 O grown biopolymers. The nSLD increase correlates to replacing about 42.5% of hydrogens present as both C–H and O–H groups in cellulose with deuterium atoms, while only 21% for lignin. In conclusion, this study lays the foundation to use partially deuterated plants to deconvolute structural features of the different component biopolymers, especially cellulose, hemicellulose, and lignin, of the plant cell wall without introducing unintended structural modifications due to the pretreatment extraction processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1999

Control Design Strategies to Enhance Long-Term Aircraft Structural Integrity

Over the operational lifetime of both military and civil aircraft, structural components are exposed to hundreds of thousands of low-stress repetitive load cycles and less frequent but higher-stress transient loads originating from maneuvering flight and atmospheric gusts. Micro-material imperfections in the structure, such as cracks and debonded laminates, expand and grow in this environment, reducing the structural integrity and shortening the life of the airframe. Extreme costs associated with refurbishment of critical load-bearing structural components in a large fleet, or altogether reinventoring the fleet with newer models, indicate alternative solutions for life extension of the airframe structure are highly desirable. Increased levels of operational safety and reliability are also important factors influencing the desirability of such solutions. One area having significant potential for impacting crack growth/fatigue damage reduction and structural life extension is flight control. To modify the airframe response dynamics arising from command inputs and gust disturbances, feedback loops are routinely applied to vehicles. A dexterous flight control system architecture senses key vehicle motions and generates critical forces/moments at multiple points distributed throughout the airframe to elicit the desired motion characteristics. In principle, these same control loops can be utilized to influence the level of exposure to harmful loads during flight on structural components. Project objectives are to investigate and/or assess the leverage control has on reducing fatigue damage and enhancing long-term structural integrity, without degrading attitude control and trajectory guidance performance levels. In particular, efforts have focused on the effects inner loop control parameters and architectures have on fatigue damage rate. To complete this research, an actively controlled flexible aircraft model and a new state space modeling procedure for crack growth have been utilized. Analysis of the analytical state space model for crack growth revealed the critical mathematical factors, and hence the physical mechanism they represent, that influenced high rates of airframe crack growth. The crack model was then exercised with simple load inputs to uncover and expose key crack growth behavior. To characterize crack growth behavior, both "short-term" laboratory specimen test type inputs and "long-term" operational flight type inputs were considered. Harmonic loading with a single overload revealed typical exponential crack growth behavior until the overload application, after which time the crack growth was retarded for a period of time depending on the overload strength. An optimum overload strength was identified which leads to maximum retardation of crack growth. Harmonic loading with a repeated overload of varying strength and frequency again revealed an optimum overload trait for maximizing growth retardation. The optimum overload strength ratio lies near the range of 2 to 3 with dependency on frequency. Experimental data was found to correlate well with the analytical predictions.

Newman, Brett A.↗
DOE OSTI2020

Soft buckling actuators

A soft actuator is described, including: a rotation center having a center of mass; a plurality of bucklable, elastic structural components each comprising a wall defining an axis along its longest dimension, the wall connected to the rotation center in a way that the axis is offset from the center of mass in a predetermined direction; and a plurality of cells each disposed between two adjacent bucklable, elastic structural components and configured for connection with a fluid inflation or deflation source; wherein upon the deflation of the cell, the bucklable, elastic structural components are configured to buckle in the predetermined direction. A soft actuating device including a plurality of the soft actuators and methods of actuation using the soft actuator or soft actuating device disclosed herein are also described.

42 ENGINEERING↗
DOE OSTI2023

Room Temperature Stamping of High-Strength Aluminum for Lightweight Structural Automotive Components

The use of aluminum (Al) 7xxx series in automobile structural applications is limited by factors such as its low room-temperature formability in T6 temper and the need for off-line artificial aging to regain high strength if it is formed in soft temper. In this study, two tempers were established that enable Al 7075 blanks to be room temperature stamped to create side impact beams that achieve near-T6 strength without post-forming artificial aging. It is shown that natural aging at room temperature, after solution treatment and before stamping, provides an alternative to high temperature pre-aging and hot stamping techniques in 7xxx alloys. Both tempers enabled room temperature stamping of the beams without cracking, indicating good formability. The Al beams were ~38% lighter than the benchmark boron steel beam. Further, the hardness in the low-deformation regions of the stamped Al beams were within 88% of a conventional 7075-T6 sheet. Paint-bake treatment of the beams appeared to cause over aging, lowering the ultimate tensile strength and ductility. Finite element three point bending simulations of the beams showed higher bending force and energy absorption before failure for the Al 7075 showing good promise for 7xxx series Al as a light-weight alternative to steel beams.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Remote sensing of row crop structure and component temperatures using directional radiometric temperatures and inversion techniques

A physically based sensor response model of a row crop was used as the mathematical framework from which several inversion strategies were tested for extracting row structure information and component temperatures using a series of sensor view angles. The technique was evaluated on ground-based radiometric thermal infrared data of a cotton row crop that covered 48 percent of the ground in the vertical projection. The results showed that the accuracies of the predicted row heights and widths, vegetation temperatures, and soil temperatures of the cotton row crop were on the order of 5 cm, 1 deg, and 2 deg C, respectively. The inversion techniques can be applied to directional sensor data from aircraft platforms and even space platforms if the effects of atmospheric absorption and emission can be corrected. In theory, such inversion techniques can be applied to a wide variety of vegetation types and thus can have significant implications for remote sensing research and applications in disciplines that deal with incomplete vegetation canopies.

Kimes, D. S.↗
NASA NTRS2004

Fracture Analysis of Semi-Elliptical Surface Cracks in Ductile Materials

Accurate life assessment of structural components may require advanced life prediction criteria and methodologies. Structural components often exhibit several different types of defects, among the most prevalent being surface cracks. A semi-elliptical surface crack subjected to monotonic loading will exhibit stable crack growth until the crack has reached a critical size, at which the crack loses stability and fracture ensues (Newman, 2000). The shape and geometry of the flaw are among the most influential factors. When considering simpler crack configurations, such as a through-the-thickness crack, a three-dimensional (3D) geometry may be modeled under the approximation of two-dimensional (2D) plane stress or plane strain. The more complex surface crack is typically modeled numerically with the Finite Element Method (FEM). A semi-elliptical surface crack is illustrated in Figure 1-1.

Daniewicz, S. R.↗
NASA NTRS1989

LaRC computational dynamics overview

Present research centers on the development of advanced computational methods for transient simulation analyses. Aircraft, launch vehicles and space structure components are potential applications, but primary focus is presently on large space structures. There are both in-house and out-of-house activities. The in-house activity centers around the development of a multibody simulation tool for truss-like structures called LATDYN for Large Angle Transient DYNamics. Multibody analysis involves articulation of structural components as well as robotic maneuvers. These items are necessary for construction (erection or deployment) of large space structures in orbit and the carrying out of certain operations on board the space station. Thus, part of the in-house activity involves the development of methods which treat the changing mass, stiffness and constraints associated with articulating systems. The out-of-house activity involves subcycling, development of large deformation/motion beam formulation, constraint stabilization and direct time integration transient algorithms in parallel computing.

Husner, J. M.↗
NASA NTRS1993

An overview of the NASA textile composites program

The NASA Langley Research Center is conducting and sponsoring research to explore the benefits of textile reinforced composites for civil transport aircraft primary structures. The objective of this program is to develop and demonstrate the potential of affordable textile reinforced composite materials to meet design properties and damage tolerance requirements of advanced aircraft structures. In addition to in-house research, the program includes major participation by the aircraft industry and aerospace textile companies. The major program elements include development of textile preforms, processing science, mechanics of materials, experimental characterization of materials, and development and evaluation of textile reinforced composite structural elements and subcomponents. The NASA Langley in-house research is focused on science-based understanding of resin transfer molding (RTM), development of powder-coated towpreg processes, analysis methodology, and development of a performance database on textile reinforced composites. The focus of the textile industry participation is on development of multidirectional, damage-tolerant preforms, and the aircraft industry participation is in the areas of innovative design concepts, cost-effective fabrication, and testing of textile reinforced composite structural elements and subcomponents. Textile processes such as 3-D weaving, 2-D and 3-D braiding, and knitting/stitching are being compared with conventional laminated tape processes for improved damage tolerance. Through-the-thickness reinforcements offer significant damage tolerance improvements. However, these gains must be weighed against potential loss in in-plane properties such as strength and stiffness. Analytical trade studies are underway to establish design guidelines for the application of textile material forms to meet specific loading requirements. Fabrication and testing of large structural components are required to establish the full potential of textile reinforced composite materials. The goals of the NASA Langley-sponsored research program are to demonstrate technology readiness with subscale composite components by 1995 and to verify the performance of full-scale composite primary aircraft structural components by 1997. The status of textile reinforced composite structural elements under development by Boeing, Douglas, Lockheed, and Grumman are presented. Included are braided frames and woven/stitched wing and fuselage panels.

Dexter, H. Benson↗
NASA NTRS2016

Automated Generation of Finite-Element Meshes for Aircraft Conceptual Design

This paper presents a novel approach for automated generation of fully connected finite-element meshes for all internal structural components and skins of a given wing-body geometry model, controlled by a few conceptual-level structural layout parameters. Internal structural components include spars, ribs, frames, and bulkheads. Structural layout parameters include spar/rib locations in wing chordwise/spanwise direction and frame/bulkhead locations in longitudinal direction. A simple shell thickness optimization problem with two load conditions is used to verify versatility and robustness of the automated meshing process. The automation process is implemented in ModelCenter starting from an OpenVSP geometry and ending with a NASTRAN 200 solution. One subsonic configuration and one supersonic configuration are used for numerical verification. Two different structural layouts are constructed for each configuration and five finite-element meshes of different sizes are generated for each layout. The paper includes various comparisons of solutions of 20 thickness optimization problems, as well as discussions on how the optimal solutions are affected by the stress constraint bound and the initial guess of design variables.

Li, Wu↗
DOE OSTI2022

Formulations and processing of cementitious components to meet target strength and CO2 uptake criteria

Provided herein are compositions and methods of carbonation processing for the fabrication of cementitious materials and concrete products. Embodiments include manufacturing processes of a low-carbon concrete product comprising: forming a cementitious slurry including portlandite; shaping the cementitious slurry into a structural component; and exposing the structural component to a CO2 waste stream, thereby enabling manufacture of the low-carbon concrete product.

Sant, Gaurav↗
DOE OSTI2024

Formulations and processing of cementitious components to meet target strength and CO 2 uptake criteria

Provided herein are compositions and methods of carbonation processing for the fabrication of cementitious materials and concrete products. Embodiments include manufacturing processes of a low-carbon concrete product comprising: forming a cementitious slurry including portlandite; shaping the cementitious slurry into a structural component; and exposing the structural component to a CO 2 waste stream, thereby enabling manufacture of the low-carbon concrete product.

Sant, Gaurav↗