Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SpaceX”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Entry, Descent, and Landing technological barriers and crewed MARSvehicle performance analysis

Mars has been explored historically only by robotic crafts, but a crewed mission encompasses several new engineering challenges – high ballistic coefficient entry, hypersonic decelerators, guided entry for reaching intended destinations within acceptable margins for error in the landing ellipse, and payload mass are all critical factors for evaluation. A comprehensive EDL parametric analysis has been conducted in support of a high mass landing architecture by evaluating three types of vehicles −70° Sphere Cone, Ellipsled and SpaceX hybrid architecture called Red Dragon as potential candidate options for crewed entry vehicles. Aerocapture at the Martian orbit of about 400 km and subsequent Entry-from-orbit scenarios were investigated at velocities of 6.75 km/s and 4 km/s respectively. A study on aerocapture corridor over a range of entry velocities (6–9 km/s) suggests that a hypersonic L/D of 0.3 is sufficient for a Martian aerocapture. Parametric studies conducted by varying aeroshell diameters from 10 m to 15 m for several entry masses up to 150 mt are summarized and results reveal that vehicles with entry masses in the range of about 40–80 mt are capable of delivering cargo with a mass on the order of 5–20 mt. For vehicles with an entry mass of 20 mt to 80 mt, probabilistic Monte Carlo analysis of 5000 cases for each vehicle were run to determine the final landing ellipse and to quantify the statistical uncertainties associated with the trajectory and attitude conditions during atmospheric entry. Strategies and current technological challenges for a human rated Entry, Descent, and Landing to the Martian surface are presented in this study.

Prabhakar Subrahmanyam↗

Model Design and Pre-Test CFD Analysis for a Supersonic Retropropulsion Wind Tunnel Test

Future Mars human lander missions will require using powered descent beginning at supersonic conditions, something which has never been done before at Mars. Significant aerosciences challenges exist due to interactions between the retrorocket exhaust plumes and the freestream flow that alter the aerodynamic behavior of the powered descent vehicle. Historically, wind tunnel tests have been used to study supersonic retropropulsion with inert gas exhaust simulants. Also, SpaceX has successfully decelerated the Falcon 9 first stage numerous times by using powered flight at supersonic conditions. On the computational side, Reynolds-Averaged Navier-Stokes flowfield simulations are regularly completed at full-scale conditions. However, the available ground and flight data do not provide a basis for calibrating the computational uncertainties for aerodynamic interference forces and moments on proposed Mars descent vehicles, either because of insufficient data or dissimilar vehicles geometries and/or conditions. Thus, additional ground testing is needed to continue addressing the aerosciences risks for large-scale human Mars landers. To that end, a retropropulsion wind tunnel test will be conducted in the NASA Langley Unitary Plan Wind Tunnel in 2020. The test is designed to improve upon similar past tests, both in terms of model design and measured data. The test campaign will use subscale model geometries derived from the two current NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry. This paper covers the reference vehicles, test objectives, model design, scaling parameters, test matrix, and computational analysis to date.

Karl T Edquist↗

TPSAS-NF1676L-31567-DND

The Stratospheric Aerosol and Gas Experiment (SAGE) III is an external payload on the International Space Station (ISS) launched on SpaceX CRS-10 on 19 February 2017 and robotically installed on ExPRESS Logistics Carrier-4 (ELC-4). First light was acquired on 17 March 2017.

Amy Rowell↗

On Orbit Flight Testing of the Roll-Out Solar Array

The Roll-Out Solar Array (ROSA) is an innovative, lightweight solar array with a flexible substrate that makes use of the stored strain energy in its composite structural members to provide deployment without the use of motors while still packaging efficiently. The ROSA flight experiment was launched to the International Space Station (ISS)on June 3rd, 2017 as a part of the eleventh SpaceX commercial resupply mission. After two weeks of storage, ROSA was extracted from the Dragon spacecraft, deployed, and put through a week of tests to verify its structural characteristics as well as the performance of photovoltaics. The structural dynamics experiments included active excitation of out-of-plane bending modes, and a study of the thermal-structural interaction of the structure during day-night transitions. Data was gathered from a small number of accelerometers located at key points on the solar array and from cameras observing numerous photogrammetry targets spread out over the structure and the photovoltaic blanket. The goal in this effort was to better understand the performance of ROSA and to improve modeling efforts for future designs of similar solar arrays. Of particular interest are the first few system modes and mode shapes of the array, the amount of structural damping present, and degree of structural-thermal interaction seen during eclipse exit.

ROSA↗

NASA’s Initial and Sustained Artemis Human Landing Systems

On March 26, 2019, in keeping with President Trump’s Space Policy Directive-1, Vice President Pence charged NASA with landing the first woman and the next man on the South Pole of the Moon by 2024, followed by a sustained presence on and around the Moon by 2028. NASA’s Human Landing System (HLS) Program is responsible for the final mode of transportation in deep space that will carry humans to and from the surface of the Moon, to be designed and developed by American companies for NASA’s Artemis lunar exploration program. This paper examines the approach for Artemis human landing systems for both the initial missions and future sustained missions. While achieving the 2024 goal requires a focus on speed and the use of mature technologies, planning toward sustained operations to and from the lunar surface requires a focus on reliability and reusability. The two approaches, however, are not mutually exclusive, as demonstrated by the HLS prime contractors’ integrated lander system proposals. On April 30, 2020, NASA announced that Blue Origin of Kent, Washington, Dynetics (a Leidos company) of Huntsville, Alabama, and SpaceX of Hawthorne, California, were the awardees for NASA’s Human Landing System contracts under Appendix H of the NextSTEP-2 Broad Agency Announcement. The companies began work in a 10-month base period during which NASA teams worked with the companies to streamline the review of required products and to share the agency’s expertise in human spaceflight systems development. Following the base period, NASA will determine which company or companies will develop the human landers for the initial missions, including the 2024 landing, and which companies will develop landers for future sustained missions toward the end of the decade.

HLS↗

NASA Electronic Parts & Packaging (NEPP) Program

The purpose of this presentation is to familiarize the people attending the JEDEC work meetings about the NEPP Program, and recent tasks we have undertaken. There is a description of the policy and testing guidelines in development and an explanation of the Government Working Group, a collaboration of several US government space agencies that come together to discuss topics relating to the reliable use of electronics. The presentation also includes a brief description of recent NASA accomplishments such as the launching/splash down of the SpaceX Crew Dragon and the launch of the next Mars rover.

reliability↗

Mercury Lander: A Planetary Mission Concept Study for the 2023–2032 Decadal Survey

Mercury holds unique clues to the distribution of elements at the birth of the solar system and how planets form and evolve in close proximity to their host stars. The Mercury Lander mission concept returns in situ measurements to: understand Mercury’s unique mineralogy and geochemistry; characterize the massive core’s structure; measure the planet’s active and ancient magnetic fields at the surface; investigate the processes that alter the surface and produce the exosphere; and provide groundtruth for remote datasets. The mission concept achieves one Mercury year (~88 Earth days) of surface operations with an 11-instrument, high-heritage payload delivered to a landing site within Mercury’s widely distributed low-reflectance material, and addresses science goals encompassing geochemistry, geophysics, the Mercury space environment, and geology. The spacecraft launches on an expendable SpaceX Falcon Heavy in 2035. The four-stage flight system uses a solar-electric propulsion cruise stage to reach Mercury in2045. The orbital stage brings the spacecraft into a thermally safe orbit, then performs orbital maneuvers to prepare for descent. During the orbital phase, a narrow-angle camera acquires images for selecting a low-hazard landing zone within our region of interest. The descent stage begins the braking burn ~120 s before landing. The lander continues to touchdown, using continuous LIDAR operations to support hazard detection and safely deliver the payload to the surface. Landing is at dusk to meet thermal requirements, permitting ~30 hours of sunlight for initial observations. The radioisotope-powered lander continues operations through the Mercury night. Direct-to-Earth communication is possible for the initial three weeks of landed operations, drops out for six weeks, and resumes for the final month. Thermal conditions exceed lander operating temperatures shortly after sunrise, ending operations. A total of ~11 GB of data are returned to Earth. The Phase A–D mission cost estimate (50% unencumbered reserves, excluding launch vehicle) is $1.2 B(FY25$), comparing favorably with past New Frontiers missions and to the cost cap in the New Frontiers4 call(~$1.1B FY25$). This cost estimate shows that a Mercury Lander mission is feasible and compelling as a New Frontiers-class mission in the coming decade.

C M Ernst↗

NASA's Initial and Sustained Artemis Human Landing Systems

On March 26, 2019, in keeping with President Trump’s Space Policy Directive-1, Vice President Pence charged NASA with landing the first woman and the next man on the South Pole of the Moon by 2024, followed by a sustained presence on and around the Moon by2028. NASA’s Human Landing System (HLS) Program is responsible for the final mode of transportation in deep space that will carry humans to and from the surface of the Moon, to be designed and developed by American companies for NASA’s Artemis lunar exploration program. This paper examines the approach for Artemis human landing systems for both the initial missions and future sustained missions. While achieving the 2024 goal requires a focus on speed and the use of mature technologies, planning toward sustained operations to and from the lunar surface requires a focus on reliability and reusability. The two approaches, however, are not mutually exclusive, as demonstrated by the HLS prime contractors’ integrated lander system proposals. On April 30, 2020, NASA announced that Blue Origin of Kent, Washington, Dynetics (a Leidos company) of Huntsville, Alabama, and SpaceX of Hawthorne, California, were the awardees for NASA’s Human Landing System contracts under Appendix H of the NextSTEP-2 Broad Agency Announcement. The companies began work in a 10-month base period during which NASA teams worked with the companies to streamline the review of required products and to share the agency’s expertise in human spaceflight systems development. Following the base period, NASA will determine which companies will develop the human landers for the initial missions, including the 2024 landing, and which companies will develop landers for future sustained missions toward the end of the decade.

Lisa Watson-Morgan↗

NASA’s Artemis Human Landing Systems: Enabling Lunar Exploration

On March 26, 2019, in keeping with Space Policy Directive-1, NASA was charged with landing the first woman and the next man on the South Pole of the Moon by 2024, followed by a sustained presence on and around the Moon by 2028. NASA’s Human Landing System (HLS) Program is responsible for the transportation in deep space to carry humans to and from the surface of the Moon, to be designed and developed by American companies for NASA’s Artemis lunar exploration program. On April 30, 2020, NASA announced the awardees for NASA’s Human Landing System contracts under Appendix H of the NextSTEP-2 Broad Agency Announcement: A Blue Origin-led team including Lockheed Martin, Northrup Grumman, and Draper; Dynetics (a Leidos company); and SpaceX. The companies began work in a multi-month base period during which NASA teams will work with the companies to streamline requirements, to establish standards and methods, to review required products and to share the NASA’s expertise in human spaceflight systems development. Following the base period, which ends in the spring of 2021, NASA will determine which company or companies will develop Artemis human landing systems for the initial demonstration missions, including the goal of landing on the Moon in 2024.This paper examines how the Human Landing System program is at the center of NASA’s Artemis lunar exploration program, designed to yield groundbreaking science, develop and utilize lunar surface resources and leverage the Moon as a proving ground for future Mars missions. While achieving the 2024 goal requires a focus on speed and the use of mature technologies, planning toward sustained operations to and from the lunar surface requires a focus on reliability and reusability.

Lisa Watson-Morgan↗

Large Vehicle Lunar Landing Surface Interaction and In-Situ Resource Based Risk Mitigation

A key capability required for the exploration of planetary bodies is the ability to land on the surface. Previous work performed by NASA and other institutions has primarily focused on landing small spacecraft on planetary surfaces and the associated small-to-medium thrusters required for the soft landing. In the case of human exploration—particularly the establishment of long duration exploration and habitation outposts—the ability to land large landers, such as the SpaceX Starship, is necessary. These larger landing systems require the use of more powerful engines, with higher temperature engine exhaust and higher landing loads. Understanding the excavation of material by the engines, as well as the potential for the landing legs to sink into the subsurface, is key in ensuring reliable and safe landings. A further improvement in landing reliability can be achieved by constructing landing/launchpads, especially with in-situ resources.

Landing Pad↗

Large Vehicle Lunar Landing Surface Interaction and In-Situ Resource Based Risk Mitigation: Landing & Launch Pads

A key capability required for the exploration of planetary bodies is the ability to land on the surface. Previous work performed by NASA and other institutions has primarily focused on landing small spacecraft on planetary surfaces and the associated small-to-medium thrusters required for the soft landing. In the case of human exploration—particularly the establishment of long duration exploration and habitation outposts—the ability to land large landers, such as the SpaceX Starship, is necessary. These larger landing systems require the use of more powerful engines, with higher engine exhaust temperatures and higher landing loads. Understanding the excavation of material by the engines, as well as the potential for the landing legs to sink into the subsurface, is key in ensuring reliable and safe landings. A further improvement in landing reliability can be achieved by constructing landing / launch pads, especially with in-situ resources. Some material excavation by the plume is inevitable, leaving at least a portion of the surface scoured and uneven under the lander and ejecting regolith particles and rocks at very high velocities. One possible solution would be to robotically build landing / launch pads (ideally autonomously) at the destination using in-situ materials. In this case, the first one or few landers will need to land on unimproved surfaces at higher risk; however, they would bring the required equipment to build the landing pads with mostly local resources, thus increasing the reliability of safe landing for subsequent larger landers. A number of methods to build in-situ landing and launch pads have already been developed. These methods include no or some addition of required binder additives to the local regolith material, different processing approaches and result in varying landing pad strengths. A sub-scale rocket engine plume, was used to simulate some of the conditions of a landing on the Moon to assess the effectiveness of various materials for an in-situ built landing pad, The GO2/GCH4 rocket engine fired on 1m2 area coupons of representative pad materials. The results will allow continued development towards materials that satisfy the landing pad properties required for the effective risk reduction and increased reliability for landing people and equipment on the lunar surface. This work contained two parts: (1) computer modeling of a large rocket engine plume interacting with regolith on the Moon, using the Granular Gas Flow Solver (GGFS) provided by CFD Research Corporation as well as other computational fluid dynamics codes (CFD) such as Loci/CHEM. (2) Developing landing/launch pad materials that could be used for in-situ construction on the lunar surface in the future, to mitigate the calculated effects of a large vehicle rocket engine landing and launching on the Moon. The resulting computed values of plume impingement surface temperature, stagnation pressure, gas velocity, shear stress and heat flux were then matched as closely as possible in the Earth’s atmosphere in a sub-scale rocket engine GO2/CH4 test which was provided by Masten Space Systems in Mojave, California. The rocket engine was mounted on a test stand with vertical translation capabilities so that the landing operations of a lander could be simulated (Figure 1).The pad materials test coupons were placed at the surface of a large bin containing simulated lunar basalt regolith and subjected to a test firing as shown in Figure 2. The results of this testing will be presented with related findings, analysis and discussion.

Plume Surface Interaction↗

Large Vehicle Lunar Landing Surface Interaction and In-Situ Resource Based Risk Mitigation: Landing & Launch Pads

A key capability required for the exploration of planetary bodies is the ability to land on the surface. Previous work performed by NASA and other institutions has primarily focused on landing small spacecraft on planetary surfaces and the associated small-to-medium thrusters required for the soft landing. In the case of human exploration—particularly the establishment of long duration exploration and habitation outposts—the ability to land large landers, such as the SpaceX Starship, is necessary. These larger landing systems require the use of more powerful engines, with higher engine exhaust temperatures and higher landing loads. Understanding the excavation of material by the engines, as well as the potential for the landing legs to sink into the subsurface, is key in ensuring reliable and safe landings. A further improvement in landing reliability can be achieved by constructing landing / launch pads, especially with in-situ resources. Some material excavation by the plume is inevitable, leaving at least a portion of the surface scoured and uneven under the lander and ejecting regolith particles and rocks at very high velocities. One possible solution would be to robotically build landing / launch pads (ideally autonomously) at the destination using in-situ materials. In this case, the first one or few landers will need to land on unimproved surfaces at higher risk; however, they would bring the required equipment to build the landing pads with mostly local resources, thus increasing the reliability of safe landing for subsequent larger landers. A number of methods to build in-situ landing and launch pads have already been developed. These methods include no, or some, addition of required binder additives to the local regolith material, different processing approaches and result in varying landing pad strengths. A sub-scale rocket engine plume, was used to simulate some of the conditions of a landing on the Moon to assess the effectiveness of various materials for an in-situ built landing pad, The GO2/GCH4rocket engine fired on a 1m2area coupons of representative pad materials. The results will allow continued development towards materials that satisfy the landing pad properties required for the effective risk reduction and increased reliability for landing people and equipment on the lunar surface. This work contained two parts: (1) computer modeling of a large rocket engine plume interacting with regolith on the Moon, using the Granular Gas Flow Solver (GGFS) provided by CFD Research Corporation as well as other computational fluid dynamics codes (CFD) such as Loci/CHEM. (2) Developing landing/launch pad materials that could be used for in-situ construction on the lunar surface in the future, to mitigate the calculated effects of a large vehicle rocket engine landing and launching on the Moon.

Lunar↗

Developing a Finite Element Soyuz Seat Environment and Investigating Occupant Injury Metrics for Accelerative Loading Across Spaceflight Vehicle Designs

Landings in the Soyuz vehicle have generated more injuries than models have predicted, and the reason for this remains unknown. Presently, 3 new capsule-type spacecraft—the Orion, the SpaceX Dragon2, and the Boeing CST-100—are in various stages of development. To better understand the injury risk to Soyuz crewmembers, and to mitigate risk of future injuries onboard the new vehicles, we conducted a finite element (FE) modeling effort. At the outset of this study, previously developed FE models were available for the seats in the 3 new vehicles, whereas the Soyuz environment had not been modeled in an extensible manner. Thus, a model of the Soyuz seat was necessary to facilitate comparisons of all seat types.

D. A. Jones↗

Preparation for and Performance of a Pseudomonas aeruginosa Biofilm Experiment On Board the International Space Station

Biofilms are a problem on Earth given their ability to degrade the materials upon which they grow and due to their relevance to infections. Remarkably, 65% and 80% of infections and chronic diseases on Earth are associated with biofilms, respectively. In space, these problems' impact is higher because the crew's lives and mission success depend on nominal operation of mechanical systems. Furthermore, the isolated confined environment nature of spaceflight may increase the rates of disease transmission. In the case of the International Space Station (ISS), biofilms are an identified problem on the Environmental Control and Life Support System (ECLSS), namely on the water processor assembly (WPA). In late 2019, the Space Biofilms experiment launched towards ISS to (i) characterize the mass, thickness, morphology, and gene expression of biofilms formed in space with respect to matched Earth controls, (ii) interrogate the expression of antimicrobial resistance genes, and (iii) test novel materials as potential biofilm control strategies for future ECLSS components. For this, 288 bacterial samples were prepared prior to the launch of the Northrop Grumman CRS-12 mission from NASA's Wallops Flight Facility. The samples were integrated into the spaceflight hardware, BioServe's Fluid Processing Apparatus (FPA) packed in sets of eight in Group Activation Packs (GAP). Half of these samples were activated and terminated on orbit by NASA astronauts Jessica Meir and Christina Koch, while the remaining half were processed equivalently on Earth. The spaceflight bacterial samples of Space Biofilms returned on board SpaceX' CRS-19 Dragon spacecraft, in early 2020. We here describe the test campaign implemented to verify the experiment design and confirm it would enable us to achieve the project's scientific goals. This campaign ended with the Experiment Verification Test (EVT), from which we here present example morphology and transcriptomic results. We describe in detail the sample preparation prior to flight, including cleaning and sterilization of the coupons of six materials (SS316, passivated-SS316, lubricant impregnated surface, catheter-grade silicone with and without a nanotopography, and cellulose membrane), loading and integration of growth media, bacterial inoculum, fixative and preservative to enable experiment termination on orbit. Additionally, we describe the performance of the experiment on board the ISS, including crew activities, use of assets, temperature profile, and experiment timeline; all leading to a successful spaceflight experiment.

Pamela Flores↗

Effects of Ambient Alcohol Levels on the Real-time Monitoring of the Atmosphere of the International Space Station

Effects of Ambient Alcohol Levels on the Real-time Monitoring of the Atmosphere of the International Space StationWilliam T. Wallace,1 Thomas F. Limero,1 Kenneth W. Clark,2 and Daniel B. Gazda31KBR, 2400 NASA Pkwy., Houston, TX 770582JES Tech, 16870 Royal Crest Dr., Houston, TX 770583NASA Lyndon B. Johnson Space Center, 2101 NASA Pkwy., Houston, TX 77058Monitoring of the spacecraft environment is required to ensure the safety of the crew and the health of the vehicle systems. For the ISS atmosphere, routine monitoring has been performed for many years by the Major Constituent Analyzer (MCA) and two Air Quality Monitors (AQMs), which, together, are used to monitor for trace (ppb) levels of 22 volatile organic compounds (VOCs). The target compounds measured by the AQMs include three types of chemicals: 1) those compounds that would be harmful to crew, 2) those compounds that have been detected regularly in archival samples, and 3) compounds that, while not necessarily harmful to crew health, could present problems for Environmental Control and Life Support Systems (ECLSS).In March 2019, following the docking of SpaceX-Demo1 (SpX-DM1), the on-board AQMs began to report extremely high levels of isopropyl alcohol (IPA). While elevated IPA is not abnormal following the docking of visiting vehicles (due to cleaning of the cargo prior to flight), the level measured by the AQM, and its continued presence following multiple days of scrubbing, caused concerns regarding the U.S. Water Recovery System. Following the departure of SpX-DM1, the IPA levels decreased to nominal levels, allowing the team to investigate the cause of the elevated measurements. Initially, based on the changes in the shape of the gas chromatograph (GC) traces in the IPA region during docked operations, it appeared that some unknown coeluting species was causing problems with quantification. However, with the docking of Northrup-Grumman-11 (NG-11), the elevated IPA concentrations returned, as well as the changes in GC traces. In contrast to the SpX-DM1 results, though, the AQM IPA results did not return to nominal levels following the departure of NG-11, suggesting that the changes could not be tied directly to the visiting vehicle.In this paper, we will discuss a number of potential causes for both the genuine (measured in archival samples) increases in IPA as well as the much higher levels measured by the AQM. Additionally, we will discuss methods being explored to decrease the potential for a reoccurrence in the future.

William T Wallace↗

Pathfinder Technology Demonstrator (PTD) Status

This paper will provide the status of the NASA Small Spacecraft Technology (SST) program’s Pathfinder Technology Demonstrator (PTD) series. Details on the development, launch, and operations of the recently completed PTD-1, as well as the planned operations of the upcoming PTD-3 and PTD-4 flights will be presented. Significant advances in the capabilities of nano-spacecraft over the past 15 years, coupled with improved access to space for CubeSats, have created new opportunities for scientific exploration using these high-value platforms. Continued development and demonstration of key technologies are improving the performance of the 1-unit (U) and 3U class CubeSats while expanding the reach of nano-spacecraft technologies into larger platforms, such as the 12-kilogram class “6U” buses. NASA’s PTD series is demonstrating a variety of new technologies on-orbit, providing proof of the maturity of these significant new technologies, and enhancing the performance of future CubeSats. Each of the four PTD flights consists of one 6U CubeSat weighing approximately 12 kilograms and measuring approximately 36 centimeters x 25 centimeters x 10 centimeters. Each flight is planned to characterize its payload within 90 days of insertion into low-Earth orbit. The PTD flights will demonstrate key technologies such as novel nano-spacecraft compatible propulsion systems, which enable deep space and maneuverable CubeSat flights; optical communications systems to facilitate high data rate collection and communications; and highly integrated systems that combine power and communication system elements to enable high power generation and novel integrated communication systems. The first PTD spacecraft, PTD-1, was placed in orbit by a SpaceX Falcon 9 launch in January of 2021 and demonstrated the functionality of the HYDROS propulsion system, developed by Tethers Unlimited of Bothell, Washington, over a period of six months. The PTD-3 flight, scheduled for launch in summer 2022, will demonstrate the TeraByte InfraRed Delivery, or TBIRD, optical communications payload developed by Massachusetts Institute of Technology Lincoln Laboratory in Lexington. The PTD-4 flight will demonstrate the Lightweight Integrated Solar Array and anTenna, or LISA-T, a payload that consists of an integrated solar array and transceiver developed by NASA’s Marshall Spaceflight Center in Huntsville, Alabama. The PTD spacecraft bus, integration and test, and flight operations services are provided by Tyvak Nano-Satellite Systems, Inc. (“Tyvak”) of Irvine, California. NASA’s SST program within the agency’s Space Technology Mission Directorate funds the PTD demonstration flights. The SST program rapidly develops and demonstrates capabilities for small spacecraft applicable to exploration, science, and the commercial sector. The program is based at NASA’s Ames Research Center.

Small Spacecraft↗

Why Mars: A Prologue

As the next wave of robotic exploration of Mars commences in the early 2020s, led by a multiplicity of space-faring nations and emerging commercial entities such as SpaceX and Blue Origin, the possibility of paradigm-shifting discoveries about the Red Planet is high. In this midst, the always-lurking question of “why Mars?” merits reconsideration. The answer ranges from seeking to enhance high-tech prowess and leadership, evolving our understanding of geology, chemistry, physics, and meteorology, to providing intellectual inspiration to a broad cross-section of the society.

James B Garvin↗

What would it take to manufacture perovskite solar cells in space?

Imagine, astronauts land on the moon. They verify their arrival with mission control, and perform system checks and validations. After the dust settles, they open the airlock of the landing vehicle and venture outside. A side hatch opens, and a flexible substrate slowly unfurls on a boom. A series of printer heads raster, hovering over the substrate and sequentially vapor-depositing the constituent layers of a perovskite solar module (Figure 1). In time, a 1-megawatt array has been manufactured on the moon and can now be connected to supply power to the Artemis Base Camp. This ambitious vision could someday become a reality. On August 29, 2021, a SpaceX Falcon 9 rocket launched a commercial resupply payload from Kennedy Space Center en route to the International Space Station (ISS). On board were perovskite solar cells that will fly for 6 months outside the ISS in low earth orbit (LEO) on the 15th Materials International Space Station Experiment (MISSE-15). This will be the first long duration flight of perovskite solar cell devices in LEO and a major step toward realizing the in-space operation and, potentially, manufacture of perovskite solar cells.

Lyndsey McMillon-Brown↗