SEARCH · Engineering Papers

Results for “Shaft Speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Incompressible flow in stepped labyrinth seals

A steped labyrinth seal was experimentally investigated to determine the effects of pressure ratio, shaft speed, number of teeth, and tooth/step location upon the leakage through the seal for incompressible flow. The dependence of the flow coefficient upon the number of throttles and pressure ratio are similar to those for straight-through labyrinth seals. It can be noted that the axial location of the throttle with respect to the step had a special effect upon the flow coefficient. That is, the dependency of the flow coefficient upon rotation rate and the number of throttles changes with axial location. It was found that the minimum flow coefficient was obtained when the seal teeth were centered on the step surface. Axial pressure distribution measurements show that when the teeth are centered on the step, the pressure drop from cavity to cavity is almost uniform. It is speculated that the obtaining of this uniform pressure gradient is the cause for the enhanced performance of the stepped labyrinth seal when operated in that configuration.

Morrison, G. L.↗

NASA NTRS1987

Braking System for Wind Turbines

Operating turbine stopped smoothly by fail-safe mechanism. Windturbine braking systems improved by system consisting of two large steel-alloy disks mounted on high-speed shaft of gear box, and brakepad assembly mounted on bracket fastened to top of gear box. Lever arms (with brake pads) actuated by spring-powered, pneumatic cylinders connected to these arms. Springs give specific spring-loading constant and exert predetermined load onto brake pads through lever arms. Pneumatic cylinders actuated positively to compress springs and disengage brake pads from disks. During power failure, brakes automatically lock onto disks, producing highly reliable, fail-safe stops. System doubles as stopping brake and "parking" brake.

Krysiak, J. E.↗

NASA NTRS1986

Advanced Gas Turbine (AGT) Technology Project

Engine testing, ceramic component fabrication and evaluation, component performance rig testing, and analytical studies comprised AGT 100 activities during the 1985 year. Ten experimental assemblies (builds) were evaluated using two engines. Accrued operating time was 120 hr of burning and 170 hr total, bringing cumulative total operating time to 395 hr, all devoid of major failures. Tests identified the generator seals as the primary working fluid leakage sources. Power transfer clutch operation was demonstrated. An alpha SiC gasifier rotor engine test resulted in blade tip failures. Recurring case vibration and shaft whip have limited gasifier shaft speeds to 84%. Ceramic components successfully engine tested now include the SiC scroll assembly, Si3N3 turbine rotor, combustor assembly, regenerator disk bulkhead, turbine vanes, piston rings, and couplings. A compressor shroud design change to reduce heat recirculation back to the inlet was executed. Ceramic components activity continues to focus on the development of state-of-the-art material strength characteristics in full-scale engine hardware. Fiber reinforced glass-ceramic composite turbine (inner) backplates were fabricated by Corning Glass Works. The BMAS/III material performed well in engine testing. Backplates of MAS material have not been engine tested.

Source record↗

NASA NTRS1987

Instability of an intershaft squeeze film damper in a two-spool rotor dynamics simulator

An instability associated with an intershaft squeeze film damper is described. The squeeze film is located between the intershaft bearing outer race and the low-speed shaft of a five-bearing, two-spool test rig. The instability is dominated by response of the third system mode to destabilizing excitation of the type described by Hibner, et al. Installing a spring cage in place of the intershaft damper removes the instability and produces satisfactory performance throughout the operating range.

Alderson, R. G.↗

NASA NTRS1987

Experiments on dynamic stiffness and damping of tapered bore seals

Stiffness and damping were measured in tapered bore ring seals with air as the sealed fluid. Excitation was provided by a known unbalance in the shaft which rotated in the test seals. Results were obtained for various seal supply pressures, clearances, unbalance amounts, and shaft speeds. Stiffness and damping varied little with unbalance level, indicating linearity of the seal. Greater variation was observed with speed and particularly supply pressure. A one-dimensional analysis predicted stiffness fairly well, but considerably overestimated damping.

Fleming, David P.↗

NASA NTRS1987

The design and analysis of single flank transmission error tester for loaded gears

To strengthen the understanding of gear transmission error and to verify mathematical models which predict them, a test stand that will measure the transmission error of gear pairs under design loads has been investigated. While most transmission error testers have been used to test gear pairs under unloaded conditions, the goal of this report was to design and perform dynamic analysis of a unique tester with the capability of measuring the transmission error of gears under load. This test stand will have the capability to continuously load a gear pair at torques up to 16,000 in-lb at shaft speeds from 0 to 5 rpm. Error measurement will be accomplished with high resolution optical encoders and the accompanying signal processing unit from an existing unloaded transmission error tester. Input power to the test gear box will be supplied by a dc torque motor while the load will be applied with a similar torque motor. A dual input, dual output control system will regulate the speed and torque of the system. This control system's accuracy and dynamic response were analyzed and it was determined that proportional plus derivative speed control is needed in order to provide the precisely constant torque necessary for error-free measurement.

Bassett, Duane E.↗

NASA NTRS1986

MSFC cryogenic turbopump bearing tester results and analysis

A full scale High Pressure Oxidizer Turbopump (HPOTP) bearing tester has been developed, and an existing test stand modified, to simulate turbopump operating conditions for Space Shuttle Main Engine HPOTP design. Following a description of test facilities and procedures, design certification and calibration tests, and tests at a moderate axial load, are discussed. Results show that a bearing life of about 4500 seconds is comparable to the life experienced in the engine pump at nominal high power level operating conditions, and that although increased coolant flow increased fluid viscous work and bearing loads, a net decrease in bearing temperature was noted. Increased coolant flow is found to improve bearing cooling for marginal conditions, and bearing temperatures are shown to become more sensitive to coolant flow as shaft speed is increased. For the 6.4 lbs/s test conditions, the heat generated in a bearing pair is determined to be about 67 percent viscous work and 33 percent contact friction.

Dolan, F. J.↗

NASA NTRS1987

Coatings for high-temperature bearings and seals

Criteria are discussed for predicting the probable lubricating ability of candidate solid materials from a consideration of their basic chemical and physical properties. The properties considered to be important in the model are thermochemical potential, adhesion, low hardness, plasticity, yield strength in shear, and brittle-to-ductile transition characteristics. A review of the selection and tribological testing of materials, which were selected for use in self-lubricating composite coatings by employing this model, is given. Two series of plasma-sprayed coatings with good tribological properties over a wide temperature spectrum are described. The PS 100 series of coatings contain oxidatively stable solid lubricants in a nichrome matrix. The PS 200 series contains the same solid lubricants in a very wear resistant metal-bonded chromium carbide matrix. Examples are given of applications of these coatings in high speed shaft seals, sliding contact bearings, and Stirling engine cylinder liners.

Sliney, Harold E.↗

NASA NTRS1988

Efficiency testing of a helicopter transmission planetary reduction stage

A parametric study of the efficiency of a 310-kW (420-hp) helicopter transmission planetary test section (four planets) was performed. The purpose was to determine the planetary contribution to the overall transmission power loss. Test parameters varied were oil flow rate, oil inlet temperature, lubricant type, shaft speed, and applied torque. The measured efficiency over all the test variables ranged from 99.44 to 99.75 percent. These experimental results were compared with other experimental and computational results.

Handschuh, Robert F.↗

NASA NTRS1987

Experiments on dynamic stiffness and damping of tapered bore seals

Fleming, D. P.↗

NASA NTRS1987

Theory versus experiment for the rotordynamic coefficients of labyrinth gas seals. II - A comparison to experiment

An experimental test facility is used to measure the leakage and rotordynamic coefficients of teeth-on-rotor and teeth-on-stator labyrinth gas seals. The test results are presented along with the theoretically predicted values for the two seal configurations at three different radial clearances and shaft speeds to 16,000 cpm. The test results show that the theory accurately predicts the cross-coupled stiffness for both seal configurations and shows improvement in the prediction of the direct damping for the teeth-on-rotor seal. The theory fails to predict a decrease in the direct damping coefficient for an increase in the radial clearance for the teeth-on-stator seal.

Childs, D. W.↗

NASA NTRS1988

Numerical and experimental evaluation of a new low-leakage labyrinth seal

The effectiveness of a recently developed leakage model for evaluating new design features of most seals is demonstrated. A preliminary assessment of the present stator groove feature shows that it gives approximately a 20 percent leakage reduction with no shaft speed effects. Also, detailed distributions of predicted streamlines, axial velocity, relative pressure and turbulence energy enhance one's physical insight. In addition, the interesting measured effect of axial position of the rotor/stator pair on leakage rate and stator wall axial pressure distribution is examined.

Rhode, D. L.↗

NASA NTRS1989

Design and test of an oxygen turbopump for a dual expander cycle rocket engine

A liquid oxygen (LOX) turbopump with an 860 R gaseous oxygen (GOX) turbine drive was designed for a 3750 lb thrust dual expander cycle rocket engine. This turbopump, which requires no interpropellant seals or system purges, features a 156 hp, single stage, full admission, impulse turbine; an axial flow inducer; a two-stage centrifugal pump with unshrouded impellers; long-life, LOX-lubricated, self-aligning, hydrostatic bearings; and a subcritical rotor design. It is constructed of Monel, a nickel-copper alloy, which has low ignition potential in oxygen. The pump was designed to deliver 34.7 gpm of 4655 psia liquid oxygen at a shaft speed of 75,000 rpm. The dual expander cycle rocket engine and the performance it requires of the LOX turbopump will be discussed as well as the design of the pump, turbine, bearings, and the turbopump rotordynamics. The test program and preliminary test results will also be presented.

Buckmann, P. S.↗

NASA NTRS1989

Small Displacement, Long Life On-Orbit Compressor Design and Fabrication

The focus is the generation of technology and fabrication of prototype hardware applicable to seven Space Station compressor system applications. The compressors are of the single acting reciprocating piston type and, in general, may be termed miniature in size compared with normal commercially available equipment. The initial technology development is focused on improved valve designs, and the control of pulsations and heating effects in order to increase compressor efficiency and reduce cycle temperatures, thus permitting significantly increased stage pressure ratios. The initial test compressor was successfully operated at pressure ratios of up to 50:1, and this significant extension of allowable pressure ratio will result in a reduction of the number of required stages and, hence, total hardware thereby reducing system weight and volume. These experiments have also identified the need to employ low shaft speeds, on the order of 250 to 500 rpm, to enhance heat transfer and increase life. The prototype compressor currently being designed, is to be driven by a low-speed brushless dc motor sealed in a case common to the compressor drive mechanism case. The compressor and motor case will communicate with stage suction pressure so that any minor gas leakage past the piston rings will be returned to the suction. Emphasis in this prototype design is being placed on simplicity, durability, commonality of components, and high efficiency.

Gerlach, C. R.↗

NASA NTRS1989

Efficiency testing of a helicopter transmission planetary reduction stage

Handschuh, R. F.↗

NASA NTRS1991

Computer Simulation Of A Small Turboshaft Engine

Component-type mathematical model of small turboshaft engine developed for use in real-time computer simulations of dynamics of helicopter flight. Yields shaft speeds, torques, fuel-consumption rates, and other operating parameters with sufficient accuracy for use in real-time simulation of maneuvers involving large transients in power and/or severe accelerations.

Ballin, Mark G.↗

NASA NTRS1992

Unsteady aerodynamic interaction effects on turbomachinery blade life and performance

This paper is an attempt to address the impact of a class of unsteady flows on the life and performance of turbomachinery blading. These class of flows to be investigated are those whose characteristic frequency is an integral multiple of rotor shaft speed. Analysis of data recorded downstream of a compressor and turbine rotor will reveal that this class of flows can be highly three-dimensional and may lead to the generation of secondary flows within downstream blading. By explicitly accounting for these unsteady flows in the design of turbomachinery blading for multistage applications, it may be possible to bring about gains in performance and blade life.

Adamczyk, John J.↗

NASA NTRS1992

Turbulence measurements of high shear flow fields in a turbomachine seal configuration

The mean velocity and Reynolds stress tensor throughout a whirling annular seal are presented. The data was collected with a three dimensional laser Doppler velocimeter using phase averaging. Two axial flow conditions (Re = 12,000 and 24,000) were studied at one shaft speed (Ta = 6,600). The eccentricity and whirl ratios were 50 and 100 percent, respectively. There is a region of high axial momentum in this region is higher in the low Reynolds number case due to an axial recirculation zone that occurs on the suction side of the rotor at the inlet. The recirculation zone does not occur in the high Reynolds number case. At both Reynolds numbers, there is a recirculation zone on the rotor surface in the pressure side of the inlet. This recirculation zone extends from 20 to 200 degrees rotor zenith in the tangential direction, and is one third of a clearance wide radially. The high Reynolds number recirculation zone is 1.5 mean clearances long, while the low Reynolds number zone extends 2 mean clearances downstream. When compared to previous studies, it is apparent that the tangential momentum is no greater for a seal with whirl than for one without if other parameters are constant. Areas of high tangential momentum occur in the clearance where the axial momentum is low. Average exit plane tangential velocities in the high Reynolds number case are 1.5 times greater than those in the other flow case. These results are in general agreement with predictions made by other investigators.

Morrison, Gerald L.↗