Examining material constitutive response under dynamic compression and large plastic strains using in situ imaging of hole closure
Abstract not provided
Lind, Jonathan↗
SEARCH · Engineering Papers
Results for “STRAIN HARDENING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Unified Stress-Strain Model for Plasticity to the Structural Instability
A unified model for the work hardening Θσ Θ(σ) and stress-strain σε σ(ε) behavior is presented that accounts for deformation under tensile loading, from the onset of yielding at the proportional limit up to the ultimate strength as defined at the structural instability. The origin of this approach is based on a negative exponential formulation for an asymptotic-curvilinear work-hardening model that accounts for the rapid strengthening of metals as well as the continuation of steady-state deformation to the instability.
36 MATERIALS SCIENCE↗
On the Onset of Plasticity: Determination of Strength and Ductility
The analysis of the work hardening variation with stress reveals insight to operative stress-strain mechanisms in material systems. The onset of plasticity can be assessed and related to ensuing plastic deformation up to the structural instability using one constitutive relationship that incorporates both behaviors of rapid work hardening (Stage 3) and the asymptotic leveling of stress (Stage 4). Results are presented for the mechanical behavior analysis of Ti-6Al-4V wherein the work hardening variation of Stages 3 and 4 are found to: be dependent through a constitutive relationship; be useful in a Hall-Petch formulation of yield strength; and provide the basis for a two point-slope fit method to model the experimental work hardening and stress-strain behavior.
36 MATERIALS SCIENCE↗
Mechanical behavior and texture evolution of WE43 magnesium-rare earth alloy in Split-Hopkinson Pressure Bar and Taylor Impact Cylinder Testing
Mechanical behavior and texture evolution of Mg rare-earth alloy WE43 is investigated for strain-rates 10 -3 /s to upwards of 10 5 /s for the two material conditions - as-cast (AC) and T6 age hardened, rolled plate (RT6). The high strain-rate behavior is tested using both Taylor cylinder impact tests (TC) and split Hopkinson pressure bar tests (SHB) and bulk textures are obtained using neutron diffraction. Unlike the quasi-static strained material, AC and RT6 SHB retained high hardening rates throughout the test, even up to 30% true strain. Moreover, the high strain-rate data revealed that the RT6 material has a much higher strength than the AC material, but similar hardening rates despite significantly different initial texture. The flow stress near yield increased up to I 0% for RT6 and up to 30% for AC as the strain-rate increased six orders of magnitude from quasi-static rates 10 -3 /s to 10 3 /s. Neither material exhibited significant plastic anisotropy over the broad range of strain rates, despite the fact that the RT6 material had a moderately strong initial texture. In the TC tests, the geometric cross-sectional changes and texture along the cylinder from the cylindrical sample foot to head are measured and from the neutron diffraction texture analysis, upper-bound estimates of twin volume fraction are obtained as well as dislocation density from analyzing diffraction peak broadening. Recorded geometrical changes along several loading directions show that the material has deformed remarkably homogeneously under impact. Analysis of deformed textures indicates that {101¯2} extension deformation twinning occurred in the RT6 condition over the range of strain rates, with an upper bound estimate of 40% twin volume fraction for approximately 0.10-0.25 true strain. The peak texture components after the impact have their c-axes closely aligned with the impact direction. As a result, these observations are presented and rationalized in the paper.
42 ENGINEERING↗
Chapter 4: Physically informed deep learning networks for simulating microstructure evolution of 3D polycrystals
As discussed in the previous chapter, high energy diffraction microscopy (HEDM) is used to study the micromechanical evolution of a material during in situ loading. HEDM experiments have been used to verify crystal plasticity (CP) simulations [119, 91, 90, 120], for experimental planning, material design, and to further analyze experimental results. However, Fast Fourier transform-based CP (CP-FFT) or finite element-based CP (CP-FE) methods are often too slow to be used in real-time during an experiment. CP-FFT is faster than CP-FE simulations due to the absence of meshing, but can still take hours to simulate the response of a single volume depending on the size and number of strain steps [127]. Reducing computation time would create a larger exploration space in planning and design, and enable faster analysis of experimental results and real-time feedback during an experiment. This research expands upon previous works to develop a workflow for predicting the full-field evolution of a 3D polycrystal. The workflow is simplified from previous works to predict only orientation and elastic strain tensors (from which stress tensors are calculated). The network is physically informed through loss functions and network architecture for a more robust model. The orientation predictions are informed about the cubic crystal symmetry of the material by incorporating disorientation and misorientation information into the network architecture and loss. The Von Mises stress is used to enforce the correct stress-strain trends in the strain tensor predictions. Additional total strain steps from the elastic and elastoplastic region are included to better capture the stress-strain evolution at smaller total strain steps. Material and hardening parameters are additional inputs into the networks to further inform the network and to study the network’s ability to predict different materials other than those used for training.
36 MATERIALS SCIENCE↗
Uniaxial tensile mechanical properties from a scratch on ultra-fine grained tungsten
We demonstrate that surface-based mechanical testing can be used to quantify a wide range of mechanical properties determined using traditional uniaxial tension experiments. These include mapping of dynamic stress–strain behaviour, which can be used as a screening tool for uniaxial tensile ductility (uniform elongation), fracture toughness (K C ), which is shown to be in good agreement with reported plane-strain K IC , as well work-hardening exponents (n), activation volumes (V) energies (Q) and strain-rate sensitivity (m) exponents as a function of temperature. Advantages of the surface-based approach are the ability to work with significantly smaller volumes and accommodate processing defects like pores, voids and cracks. These methods are applied to ultra-fine grained tungsten (average grain size of 650 nm), as it is an ideal candidate for alloy development efforts in advanced energy systems. Tungsten is a useful baseline as it exhibits a near-ambient temperature (approx. 200°C) ductile-to-brittle transition temperature (DBTT), enabling validation efforts for the proposed methods, and extraordinary material properties, including the highest melting temperature of any metal and complex temperature and strain-rate dependencies linked to transitions in dislocation mechanisms.
36 MATERIALS SCIENCE↗
A System-Level Model for Estimating Residual Strain and Life of Nuclear Reactor Coolant System Components Under Connected-System-Thermal–Mechanical Boundary Conditions
Background: Environmental-assisted fatigue (EAF) is a major issue for the long-term survival of nuclear power plant fleets in the U.S. and worldwide. Multi-material welded regions (e.g., nozzles) and other high-stress regions of reactor coolant system (RCS) components are prone to EAF-related damage. Objective: The discussed work describes a system-level finite element (FE) model of RCS components of a pressurized water reactor (PWR). This is with the goal of predicting the stress hotspots, strain residuals, strain amplitudes and the resulting fatigue lives. Methods: Herein, the FE model was developed considering system-level loading conditions (under connected system thermal-mechanical boundary conditions). Thermal-mechanical stress analysis was performed considering thermal stratification and a design-basis reactor loading cycle. Based on the FE model results, the strain residuals, strain amplitudes and resulting fatigue lives of RCS components were predicted. Results: The results show that some of the RCS components can have significantly different strain amplitudes, residual strain, and fatigue lives, despite having similar geometry and material. Higher residual strain can lead to accelerated cyclic hardening of material and the associated effect of EAF. The simulated component-level strain profile (under realistic multi-axial-multi-physics loading cycle) can guide the selection of appropriate test inputs for conducting laboratory-scale EAF tests, which is a focus of future works. Conclusions: Despite similar geometry and material the RCS component can have significantly different strain profiles and resulting fatigue lives. The discussed approach can help to identify and prioritize the RCS components for conducting expensive nondestructive evaluation (NDE) inspections.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Plasticity in irradiated FeCrAl nanopillars investigated using discrete dislocation dynamics
Here, in this paper, we investigate plasticity in irradiated FeCrAl nanopillars using discrete dislocation dynamics simulations (DDD), with comparisons to transmission electron microscopic (TEM) in situ tensile tests of ion- and neutron-irradiated commercial C35M FeCrAl alloy. The effects of irradiation-induced defects, such as a/2<111> and a<100> type loops and composition fluctuations representative of phase separation in irradiated FeCrAl alloys, are investigated separately as well as superposed together in simulations. We explore the effects of defects on the stress-strain behavior, specifically yield strength and hardening response, of FeCrAl nanopillars. Our simulations confirm the widely accepted fact that irradiated alloys exhibit a stress-strain response with higher yield strength as compared to unirradiated alloys. However, our DDD calculations reveal an atypical superposition of the hardening contributions due to composition inhomogeneity and irradiation loops wherein composition inhomogeneity annihilates the hardening due to irradiation loops at small scales. As a result, we observe that the yield strength in irradiated alloys, after taking into consideration the effects of both composition inhomogeneity and irradiation loops, is smaller than the yield strength of the alloys with only irradiation loops and is approximately same for the alloy with composition inhomogeneity alone. This is referred to as “destructive interference” between the hardening contributions due to composition fluctuations and irradiation loops in the paper. We also identify this destructive interference in the superposition in our parallel TEM in situ tensile tests on unirradiated, ion-irradiated, and neutron-irradiated C35M FeCrAl alloy. This destructive interference in the hardening contributions contrasts with the dispersed barrier hardening (DBH) models widely utilized by the experimental community to model the hardening contributions due to different irradiation induced defects. The effects of the loading orientations on the yield strength and hardening are investigated and the mechanisms for the hardening in irradiated FeCrAl alloys are also reported.
36 MATERIALS SCIENCE↗
Distributed strain sensing using Bi-metallic coated fiber optic sensors embedded in stainless steel
Silica fiber optic sensors are resistant to corrosive environments and high temperatures, making them attractive candidates for harsh conditions found in nuclear and aerospace industries. Moreover, fibers can be deployed remotely for continuous measuring of spatially distributed temperatures and strains. Here, this study investigated embedding a Ni/Cu bi-metallic coated fiber in a stainless-steel 316 (SS316) matrix using laser powder bed fusion towards functionalizing metal components for site-specific health monitoring. The embedded fiber was continuously interrogated during controlled heating to 1000°C. The measured fiber strains were similar to the expected differential thermal strains between the fiber and the SS316 matrix, until divergent behavior was observed at temperatures >500°C. No debonding at the matrix–coating–fiber interfaces was observed during microscopy, but significant interactions between the coatings and matrix resulted in diffusion-driven chemistry variations and Kirkendall void formation. Applying the strain-lag theory revealed plastic behavior in the Ni coating at temperatures >500°C, limiting the strain transfer to the fiber at higher temperatures. It was estimated that the elastic modulus in the Ni coating had decreased from ~200 GPa at room temperature to below 40 GPa, starting at 600°C. The low elastic modulus above 600°C is within the margin of what the tangent modulus would be in the case of bilinear isotropic hardening. Regardless of the divergent strain transfer at higher temperatures, the fiber was exposed to the equivalent of 1.9 % engineering strain at 1000°C, but measured only a 0.7 % engineering strain due to the poor strain transfer. Although compensating for the plastic behavior of Ni proved challenging, the bonding of a brittle silica fiber to a metal matrix surviving to 1000°C invites potential iterations on coating material for future application. For example, the embedded fiber is sufficient for acoustic energy transfer, realizing high temperature distributed acoustic sensing.
36 MATERIALS SCIENCE↗
On the origin of stress-strain relationships, the evaluation of softening coefficients, and mechanistic models for work hardening
Not Available
Jankowski, Alan F. (ORCID:0000000317816957)↗
Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures
Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.
36 MATERIALS SCIENCE↗
Dynamic Strength and Equation of State of Epon 828 and Diethanolamine (DEA) Polymer Epoxy Under Shock Loading
Polymers are increasingly utilized in engineering applications that can experience high loading rates, necessitating increased understanding of their response under such conditions. The tamped Richtmyer-Meshkov Instability (RMI) method was used to characterize the equation of state and dynamic strength of the polymer Epon 828 cured with Diethanolamine (DEA). Plate impact experiments that drove a uniaxial shock compression wave across a sinusoidally corrugated metal-polymer interface were performed to generate shock stresses from 4-12 GPa and strain rates of approximately 1/s in the polymer. X-ray phase contrast imaging recorded the shock motion in the polymer and subsequent interface evolution. Analysis of this data yielded the polymer equation of state and, in conjunction with numerical modeling, the dynamic strength. The equation of state was validated against one-dimensional plate impact experiments from existing literature. The dynamic strength was compared to prior data for Epon 828 and related polymers at lower strain rates and found to exhibit significant strain rate and pressure-hardening effects. The strength of the Epon 828 polymer at 10 6 1/s was found to be approximately 1.5 GPa, suggesting that it is comparable to the strength of high strength metals at these dynamic conditions.
Equation of state↗
Enhanced work hardening from oxygen-stabilized ω precipitates in an aged metastable β Ti-Nb alloy
High levels of oxygen in solid solution in Ti alloys are considered detrimental to mechanical properties because of embrittlement concerns. In metastable β titanium alloys, the formation of isothermal ω precipitates is also known to cause severe embrittlement and ductility reduction. However, oxygen has been shown to partition to the ω phase during ageing, and this partitioning behavior may potentially impact ω’s mechanical contribution. Using micropillar compression, we compared the deformation behavior of Ti-20Nb (at. %) with oxygen-stabilized ω precipitates to the behavior of oxygen-free specimens. The oxygen-stabilized microstructures showed increased compressive yield strength and enhanced work hardening behavior compared to oxygen-free specimens. In the absence of oxygen, the compressed pillars showed slip band formation and catastrophic failure, and transmission electron microscopy imaging revealed that ω precipitates were sheared within the continuous deformation channels resulting in slip localization. In contrast, oxygen-stabilized ω precipitates were harder to shear and the formation of continuous deformation channels was suppressed during compression, leading to improved work hardening behavior up to 15% strain. Furthermore, this counter-intuitive role of oxygen may offer design strategies to address the significant embrittlement and loss of ductility observed for ω-strengthened β Ti alloys without oxygen and avenues to expand the use of β Ti alloys.
36 MATERIALS SCIENCE↗
Modification of the MTS model for high strain-rate behavior of TI-6AL-4V
The Mechanical Threshold Stress (MTS) model provides excellent predictive capabilities for the material constitutive response for a wide range of temperatures and strain rates. However, the MTS model fails to capture the rapidly increasing yield stress at high strain rate behavior as the deformation controlling mechanism transitions from thermal activation to drag mechanisms, only capturing the linear behavior. Further, the model typically over predicts the flow stress behavior at yield and post yield due to its use of a constant work hardening rate parameter derived from the stress–strain response at constant saturation stress. An alternative approach to fitting portions of the MTS model is investigated and mathematical models are developed to address these issues. The results show that with appropriate experimental data, the mechanical threshold stress and work hardening rate parameters within the MTS model can quite easily and accurately be modified to extend applicability to high strain rate behavior and more accurately model the initial flow stress behavior at early work hardening rates without modification of the functions core to the MTS model itself.
36 MATERIALS SCIENCE↗
Probing multi-dimensional composition spaces in search of strong metallic alloys
Refractory complex concentrated alloys (RCCA) offer exceptionally high-temperature strength compared to pure metals and dilute alloys, but predictive theory for RCCA design is lacking. We present large-scale molecular Dynamics (MD) simulations of crystal plasticity to explore alloy compositions for maximum mechanical strength, focusing on Fe-Ta-W and Nb-Ta-Mo-W alloy families modeled with Embedded Atom Model (EAM) and Spectral Neighbor Analysis Potentials (SNAP). To efficiently guide the search for strong alloy compositions, we employ iterative optimization using Gaussian process regression. Many simulated RCCA compositions exhibit pronounced cocktail strengthening, with strengths surpassing their strongest constituent metal, tungsten. Contrary to expectations, the highest strength is found on binary edges of the RCCA composition space. Detailed analyses of atomistic simulations reveal that, similar to pure BCC metals, plastic response in RCCA is primarily governed by screw dislocations. However, at large strains, dislocation multiplication and interactions (Taylor hardening) become the dominant mechanisms contributing to RCCA strength.
Materials science↗
A Constitutive Structural Parameter for the Work Hardening Behavior of Additively Manufactured Ti-6Al-4V
The mechanical behavior of Ti-6Al-4V produced by additive manufacturing processes is assessed based on a formulation developed from the Kocks-Mecking relationship. A constitutive parameter derived for the microstructure is characteristic of the work hardening behavior determined by the plastic strain between the proportional limit and the strength at the instability point. The varied plasticity behavior associated with surface and build direction effects can be evaluated with this approach as presented for the case of Ti-6Al-4V under uniaxial tension.
36 MATERIALS SCIENCE↗
Self-equilibrated backstresses induce compensation between hardening and softening: Micromechanical and microstructural features
For crystal plasticity formulation neglecting the strain gradients at the dislocation scale, backstresses are necessary to satisfy the mesoscopic stress equilibrium and strain compatibility requirements. Backstresses in a material point and those between neighboring points are treated separately. Physically backstresses can dynamically induce either hardening or softening effects to adjust the dislocation hardening of slip systems, whereas the sum of the stresses resulting in backstresses in the representative volume element (RVE) is zero. Backstress hardening suppresses certain slip activities, while backstress softening triggers excess dislocations. A two-phase brass is studied. Backstresses make the hard phase deform smaller and the soft phase deform more than those without employing backstresses in a model. In the former, more homogeneous lattice strain and higher yield stress are obtained. Backstress has limited effects on the evolution of the critical resolved shear stress and crystallographic texture. Furthermore, it is a major cause of the banded structures featuring sharp crystallographic contrasts which are not parallel to the slip planes. Tests indicate that backstress induces a serrated behavior at the early stages of deformation and induces the geometrically necessary bands (GNBs), which are parallel to the macroscopic axes.
36 MATERIALS SCIENCE↗
Mechanical characterization of 304L-VAR stainless steel in tension with a full coverage of low, intermediate, and high strain rates
A 304L-VAR stainless steel is mechanically characterized in tension over a full range of strain rates from low, intermediate, to high using a variety of apparatuses. While low- and high-strain-rate tests are conducted with a conventional Instron and a Kolsky tension bar, the tensile tests at intermediate strain rates are conducted with a fast MTS and a Drop-Hopkinson bar. The fast MTS used in this study is able to obtain reliable tensile response at the strain rates up to 150 s -1 , whereas the lower limit for the Drop-Hopkinson bar is 100 s -1 . Combining the fast MTS and the Drop-Hopkinson bar closes the gap within the intermediate strain rate regime. Using these four apparatuses, the tensile stress-strain curves of the 304L-VAR stainless steel are obtained at strain rates on each order of magnitude ranging from 0.0001 to 2580 s -1 . All tensile stress-strain curves exhibit linear elasticity followed by significant work hardening prior to necking. After necking occurrs, the specimen load decreases, and the deformation becomes highly localized until fracture. The tensile stress-strain response of the 304L-VAR stainless steel exhibits strain rate dependence. The flow stress increases with increasing strain rate and is described with a power law. The strain-rate sensitivity is also strain-dependent, possibly due to thermosoftening caused by adiabatic heating at high strain rates. The 304L-VAR stainless steel shows significant ductility. The true strains at the onset of necking and at failure are determined. The results show that the true strains at both onset of necking and failure decrease with increasing strain rate. The true failure strains are approximately 200% at low strain rates but are significantly lower (~100%) at high strain rates. The transition of true failure strain occurs within the intermediate strain rate range between 10 -2 and 10 2 s -1 . A Boltzmann description is used to present the effect of nominal strain rate on true failure strain.
304L-VAR stainless Steel↗