Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Opacified silica reusable surface insulation /RSI/ for thermal protection of the Space Shuttle Orbiter

The present paper deals with a second-generation reusable surface insulation (RSI) material, termed LI-2200, which has been chosen for use on limited areas of the Orbiter heat shield. It is a rigid sintered fibrous silica containing about 3% by weight 1200 grit silicon carbide powder, capable of surviving multiple reentries at temperatures on the order of 1400 C. The lower thermal conductivity achieved by opacification with silicon carbide is demonstrated by radiant transmission measurements and thermal response tests.

Goldstein, H. E.↗
NASA NTRS1980

Performance of fused silica as a filter in a wide field-of-view earth radiation budget radiometer

The thermal response of the fused silica dome filter in an earth radiation budget WFOV shortwave channel conceptual design and the impact of that response on the channel measurement, is described. Attention is given to results from design definition and performance analysis studies. Consideration is given to problems associated with achieving the desired levels of confidence in a high accuracy filtered earth radiation budget WFOV radiometer. Finally, design approaches, ground calibration, and data reduction techniques that minimize measurement uncertainties are covered.

Cooper, J. E.↗
NASA NTRS1980

Dependence of growth rate of quartz in fused silica on pressure and impurity content

The effects of pressure, temperature, and some variations in impurity content on the growth rate u of quartz into fused silica were measured. Under all conditions the growth rate was interface controlled and increased exponentially with pressure with an activation volume averaging -21.2 cu cm/mole. The activation enthalpy for all specimens is extrapolated to a zero pressure value of 64 kcal/mole, within the experimental uncertainty. At a given stoichiometry the effect of hydroxyl content on growth rate is described entirely by a linear term C(OH) in the prefactor of the equation for the growth rate. The effect of chlorine impurity can be described similarly. Also u is increased as the ideal stoichiometry is approached from the partially reduced state.

Fratello, V. J.↗
NASA NTRS1980

Hot isostatic pressing of silicon nitride Sisub3n4 containing zircon, or zirconia and silica

A hydrothermal synthesis apparatus with a 10 KB cylinder was used to obtain a sintered body of silicon nitride. The sintering auxiliary agents used were zircon (ZrSiO4) and a mixture of zirconia (ZrO2) and silica (SiO2). Experiments were conducted with the amounts of ZrSi04 or ArO2 and SiO2 varying over a wide range and the results compared to discover the quantity of additive which produced sintering in silicon nitride by the hot pressing method.

Somiya, S.↗
NASA NTRS1980

Some characteristics of powder silica counters

Following the original idea of Peters, techniques have been developed to fabricate large area powder silica counters with refractive index between 1.06 to 1.12 in thicknesses of 1 cm and 2 cm respectively. The maximum size counter is 25 cm x 25 cm but the technique can be easily extended to 40 cm x 30 cm counters. Techniques have also been developed to dope this counter with the wavelength shifter p-terphenyl uniformly. The results of test runs at the Brookhaven National Laboratory and of laboratory runs using a superconducting magnet spectrometer on their performance are reported.

Badhwar, G. D.↗
NASA NTRS1981

Short-term stability of high-silica glasses

The devitrification characteristics of high-silica (70-90%) glasses for use in potential higher temperature coatings on advanced insulation systems for space vehicles were determined at 1260 C after 24 h. These data indicate that additives can be used to maintain the stability of these coatings relative to cristobalite formation.

Leiser, D. B.↗
NASA NTRS1983

Shrinkage of amorphous silica fibers

By the application of a new technique, the viscosity of amorphous silica fibers was determined in the 1100-1350 C temperature range. An equation was derived that describes the kinetics of shrinkage of the fibers in terms of their radius, viscosity, and surface tension.

Zaplatynsky, I.↗
NASA NTRS1983

Transmittance and reflectance of crystalline quartz and highand low-water content fused silica from 2 microns to 1 mm

The transmittances and reflectances of cultured crystalline quartz, Suprasil, Suprasil W, and Infrasil were compared over the wavelength region from 2 to 1000 microns. The high-water content of Suprasil and the low-water content of cultured crystalline quartz, Suprasil W, and Infrasil were determined by their transmittances measured at 2.73 microns where water content causes high absorption in optical materials. The fact that the fused silicas, both with high- and low-water content, had identical far-IR transmittances and that their transmittances were greatly inferior to that of crystalline quartz led to the conclusion that their inferior transmittance is due to their amorphous structure and not to their water content.

Heaney, J. B.↗
NASA NTRS1983

Fused silica mirror evaluation for the Shuttle Infrared Telescope Facility (SIRTF)

The SIRTF optics are intended for operation at 20 K (or less); it will be extremely inconvenient, expensive, and time consuming if it becomes necessary to accomplish all of the optical element testing, assembly, and alignment at comparable temperatures. The thermal strain behavior, including potential anisotropies and inhomogeneities, of a mirror substrate between room temperature and 20 K thus becomes a major factor in the selection of the substrate material, structural configuration, and joining methods for lightweight structures. With support from Space Projects, NASA Ames Research Center, an optical figure evaluation of a 0.65-meter, lightweight, fused silica mirror at a low-temperature goal of 20 K is being conducted. The design details of a thermal shroud, provisions for extracting heat from the low-conductivity mirror, and wavefront error sources other than the mirror surface are discussed and preliminary test results presented.

Barnes, W. P., Jr.↗
NASA NTRS1984

Chemical substitution in silica polymorph

Ion and electron probe analyses are presented for trace elements (Al, Na, K, Li, Ti) in quartz, tridymite, cristobalite and melanophlogite. Quartz and melanophlogite show low levels of trace elements relative to tridymite and cristobalite. The previously determined alpha-beta inversion temperature decreases as the Al content of quartz increases. For all silica polymorphs, Al is greater than or equal to Na + K + Li on an atom basis, with the excess Al probably balanced by H.

Smith, J. V.↗
NASA NTRS1985

Waterproofing Agents for Silica Tiles

Waterproofing agent methyltrimethoxysilane applied to silica thermal insulation tiles in simple vapor-deposition process. Other waterproofing agents in same series include methylsiloxane and hexamethyldisilazane. Originally developed for insulating tiles for spacecraft, agents also find uses in roofing tiles, insulation for buildings or solar-energy systems, or solar reflectors.

Nakano, H. N.↗
NASA NTRS1984

Crystallization of calcia-gallia-silica glasses

A thermal image furance is presently used to study the critical cooling rate for glass formation, and the kinetics of crystallization, of the compositions 18.4CaO-(81.6-X)Ga2O3-XSiO2, where X = 3, 6, 9, and 13.8. Crystallization was studied nonisothermally, and the data were analyzed in light of the Avrami (1939) equation. Critical cooling rate and crystallization activation energy are both found to decrease with increasing silica content, and the results obtained by the present technique are noted to agree with those obtained on the basis of differential thermal analysis measurements.

Ray, C. S.↗
NASA NTRS1983

Infrared telescope design - Implications from cryogenic tests of fused-silica mirrors

A brief review of results from recent cryogenic tests of fused-silica mirrors is given with consideration of the implications for the design of cooled infrared telescopes. Implications include optical performance with a discusion of the top-down optical error budgeting for the Shuttle Infrared Telescope Facility (SIRTF), thermal properties of the mirrors, and mirror mounting.

Melugin, R. K.↗
NASA NTRS1985

Effect of processing treatments on strength of silica thread for quilted ceramic insulation on Space Shuttle

The effects of chemical, mechanical, and thermal processing treatments on the preflight strength properties of a silica sewing thread used to fabricate an external flexible Thermal Protection System (TPS) for the Space Shuttle vehicle are discussed. Below 540 C, loss of strength was observed for all treatments studied, but above conditioning temperatures of 540 C little change in strength properties was measured, indicating no appreciable mechanical damage to the yarn as a consequence of these processing treatments.

Sawko, P. M.↗
NASA NTRS1986

Attaching Metal Fasteners to Silica Tiles

Stress distributed so high load borne. Fastener bonded in densified hole or captured in plug of similar refractory material, which in turn bonded in hole in parent tile. Plug or bonding distributes mechanical load from fastener to broad region surrounding fastener, reducing local stress concentration and likelihood of breakage. Bonded-plug method has been successful in attaching mechanical fasteners to porous silica refractory tiles used on outer surface of Space Shuttle orbiter.

Holt, J. W.↗
NASA NTRS1985

Phenomenological study of the behavior of some silica formers in a high velocity jet fuel burner

Samples of four silica formers: single crystal SiC, sintered alpha-SiC, reaction sintered Si3N4 and polycrystalline MoSi2, were subjected to a Mach 1 jet fuel burner for 1 hr, at a sample temperature of 1375 deg C (2500 deg F). Two phenomena were identified which may be deleterious to a gas turbine application of these materials. The glass layer formed on the MoSi2 deformed appreciably under the aerodynamic load. A scale developed on the samples of the other materials which consisted of particular matter from the gas stream entrapped in a SiO2 matrix.

Cawley, J. D.↗
NASA NTRS1986

Solar-grade silicon prepared by carbothermic reduction of silica

An advanced carbothermic reduction (ACR) process was developed to produce solar grade (SC) silicon from high purity silica and carbon. Preparation of starting materials and operation of the arc furnace to product high purity silicon is described. Solar cells prepared from single crystal SG-Si had efficiencies of up to 12.3% practically identical to cells made from electronic grade silicon. The ACR process is not in the pilot stage for further evaluation.

Aulich, H. A.↗