Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Refractory materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Evaluation of Geopolymer Concrete for Rocket Test Facility Flame Deflectors

The current paper presents results from a combined research effort by Louisiana Tech University (LTU) and NASA Stennis Space Center (SSC) to develop a new alumina-silicate based cementitious binder capable of acting as a high performance refractory material with low heat ablation rate and high early mechanical strength. Such a binder would represent a significant contribution to NASA's efforts to develop a new generation of refractory 'hot face' liners for liquid or solid rocket plume environments. This project was developed as a continuation of on-going collaborations between LTU and SSC, where test sections of a formulation of high temperature geopolymer binder were cast in the floor and walls of Test Stand E-1 Cell 3, an active rocket engine test stand flame trench. Additionally, geopolymer concrete panels were tested using the NASA-SSC Diagnostic Test Facility (DTF) thruster, where supersonic plume environments were generated on a 1ft wide x 2ft long x 6 inch deep refractory panel. The DTF operates on LOX/GH2 propellants producing a nominal thrust of 1,200 lbf and the combustion chamber conditions are Pc=625psig, O/F=6.0. Data collected included high speed video of plume/panel area and surface profiles (depth) of the test panels measured on a 1-inch by 1-inch giving localized erosion rates during the test. Louisiana Tech conducted a microstructure analysis of the geopolymer binder after the testing program to identify phase changes in the material.

Allgood, Daniel C.↗

High-Temperature Graphite/Phenolic Composite

Graphite-fiber/phenolic-resin composite material retains relatively high strength and modulus of elasticity at temperatures as high as 1,000 degrees F. Costs only 5 to 20 percent as much as refractory materials. Fabrication composite includes curing process in which application of full autoclave pressure delayed until after phenolic resin gels. Curing process allows moisture to escape, so when composite subsequently heated in service, much less expansion of absorbed moisture and much less tendency toward delamination. Developed for nose cone of external fuel tank of Space Shuttle. Other potential aerospace applications for material include leading edges, parts of nozzles, parts of aircraft engines, and heat shields. Terrestrial and aerospace applications include structural firewalls and secondary structures in aircraft, spacecraft, and ships. Modified curing process adapted to composites of phenolic with other fiber reinforcements like glass or quartz. Useful as high-temperature circuit boards and electrical insulators.

Seal, Ellis C.↗

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part B: required research in present tokamaks

Abstract The companion part A paper (Stangeby et al 2022) reports a number of independent estimates indicating that high-duty-cycle DT tokamaks starting with pilot plants will likely experience rates of net erosion and deposition of solid PFC, plasma facing component, material in the range of 10 3 to 10 4 kg yr −1 , regardless of the material used. The subsequent redeposition of such large quantities of material has the potential for major interference with tokamak operation. Similar levels and issues will be involved if ∼continuous low-Z powder dropping is used for surface conditioning of DT tokamaks, independent of the material used for the PFC armor. In Stangeby et al (2022) (part A) it is proposed that for high-duty-cycle DT tokamaks, non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for protecting the main walls, while reducing the risk of degrading the confined plasma. Assessment of whether such an approach is viable will require information, much of which is not available today. Section 6 of part A identifies a partial list of major physics questions that will need to be answered in order to make an informed assessment. This part B report describes R&D needed to be done in present tokamaks in order to answer many of these questions. Most of the required R&D is to establish better understanding of low-Z slag generation and to identify means to safely manage it. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Method of repairing surface damage to porous refractory substrates

A damaged porous refractory material coated with a glass coating is repaired by applying hydrolyzed tetraethyl orthosilicate to the damaged area and curing it. A pliable filler comprised of hydrolyzed tetraethyl orthosilicate and powdered refractory substrate is then applied to the area which is then heated.

Ecord, G. M.↗

Toward high laser power beam manipulation with nanophotonic materials: evaluating thin film damage performance

Nanophotonic materials enable unprecedented control of light-matter interactions, including the ability to dynamically steer or shape wavefronts. Consequently, nanophotonic systems such as metasurfaces have been touted as promising candidates for free-space optical communications, directed energy and additive manufacturing, which currently rely on slow mechanical scanners or electro-optical components for beam steering and shaping. However, such applications necessitate the ability to support high laser irradiances (> kW/cm 2 ) and systematic studies on the high-power laser damage performance of nanophotonic materials and designs are sparse. Here, we experimentally investigate the pulsed laser-induced damage performance (at λ ∼ 1 µm) of model nanophotonic thin films including gold, indium tin oxide, and refractory materials such as titanium nitride and titanium oxynitride. We also model the spatio-thermal dissipation dynamics upon single-pulse illumination by anchoring experimental laser damage thresholds. Our findings show that gold exhibits the best laser damage resistance, but we argue that alternative materials such as transparent conducting oxides could be optimized to balance the tradeoff between damage resistance and optical tunability, which is critical for the design of thermally robust nanophotonic systems. We also discuss damage mitigation and ruggedization strategies for future device-scale studies and applications requiring high power beam manipulation.

36 MATERIALS SCIENCE↗

Anisotropic Hexagonal Boron Nitride Nanomaterials - Synthesis and Applications

Boron nitride (BN) is a synthetic binary compound located between III and V group elements in the Periodic Table. However, its properties, in terms of polymorphism and mechanical characteristics, are rather close to those of carbon compared with other III-V compounds, such as gallium nitride. BN crystallizes into a layered or a tetrahedrally linked structure, like those of graphite and diamond, respectively, depending on the conditions of its preparation, especially the pressure applied. Such correspondence between BN and carbon readily can be understood from their isoelectronic structures [1, 2]. On the other hand, in contrast to graphite, layered BN is transparent and is an insulator. This material has attracted great interest because, similar to carbon, it exists in various polymorphic forms exhibiting very different properties; however, these forms do not correspond strictly to those of carbon. Crystallographically, BN is classified into four polymorphic forms: Hexagonal BN (h-BN) (Figure 1(b)); rhombohedral BN (r-BN); cubic BN (c-BN); and wurtzite BN (w-BN). BN does not occur in nature. In 1842, Balmain [3] obtained BN as a reaction product between molten boric oxide and potassium cyanide under atmospheric pressure. Thereafter, many methods for its synthesis were reported. h-BN and r-BN are formed under ambient pressure. c-BN is synthesized from h-BN under high pressure at high temperature while w-BN is prepared from h-BN under high pressure at room temperature [1]. Each BN layer consists of stacks of hexagonal plate-like units of boron and nitrogen atoms linked by SP{sup 2} hybridized orbits and held together mainly by Van der Waals force (Fig 1(b)). The hexagonal polymorph has two-layered repeating units: AA'AA'... that differ from those in graphite: ABAB... (Figure 1(a)). Within the layers of h-BN there is coincidence between the same phases of the hexagons, although the boron atoms and nitrogen atoms are alternatively located along the c-axis. The rhombohedral system consists of three-layered units: ABCABC..., whose honeycomb layers are arranged in a shifted phase, like as those of graphite. Reflecting its weak interlayer bond, the h-BN can be cleaved easily along its layers, and hence, is widely used as a lubricant material. The material is stable up to a high temperature of 2300 C before decomposition sets in [2] does not fuse a nitrogen atmosphere of 1 atm, and thus, is applicable as a refractory material. Besides having such properties, similar to those of graphite, the material is transparent, and acts as a good electric insulator, especially at high temperatures (10{sup 6} {Omega}m at 1000 C) [1]. c-BN and w-BN are tetrahedrally linked BN. The former has a cubic sphalerite-type structure, and the latter has a hexagonal wurtzite-type structure. c-BN is the second hardest known material (the hardest is diamond), the so-called white diamond. It is used mainly for grinding and cutting industrial ferrous materials because it does not react with molten iron, nickel, and related alloys at high temperatures whereas diamond does [1]. It displays the second highest thermal conductivity (6-9 W/cm.deg) after diamond. This chapter focuses principally upon information about h-BN nanomaterials, mainly BN nanotubes (BNNTs), porous BN, mono- and few-layer-BN sheets. There are good reviews book chapters about c-BN in [1, 4-6].

36 MATERIALS SCIENCE↗

A Study on the Interfacial Reaction Between Liquid Iron and MgO-Based Refractories Containing TiO{sub 2}

The interfacial reactions between liquid iron and MgO-based refractories were investigated based on the TiO{sub 2} concentration values. Substrates comprising MgO, MgO-TiO{sub 2} (MT), MgO-Al{sub 2}O{sub 3} (MA), and MgO-Al{sub 2}O{sub 3}, at loadings of 3, 6, 9, 12, and 15 wt pct TiO{sub 2} (MAT3-15), were reacted with liquid iron at 1823 K by using the sessile drop technique. Microscopic analysis by SEM/EDX and the associated thermochemical calculations by Factsage 7.0™ confirmed the reaction mechanisms of different refractory materials. MgO and MT showed higher resistance against liquid iron penetration compared with MA and MAT3-15, which was attributed to the formation of a magnesiowustite (MO (M = Fe, Mg)) layer formed at the interfaces. Increasing the levels of TiO{sub 2} up to 6 wt pct contributed to the denser microstructure of MA. However, the contact angle was lowest for 9 wt pct of TiO{sub 2} and then gradually increased up to 15 wt pct. Chemical reactions generating a liquid slag phase contributed to the fluctuations in contact angle with respect to TiO{sub 2}.

36 MATERIALS SCIENCE↗

Emission spectrometric arcing procedure with minimal effect of chemical form of sample

Matrix effects related to the chemical form of analyzed materials were studied. An arc in argon was used which was buffered with silver chloride. The effect of chemical form was minimal for a variety of metals, oxides, and carbides representing the most refractory compounds and thermally stable metal-containing molecules. Only four of the most refractory materials known showed significant emission depressions due to incomplete volatilization in the arc system. These results are discussed in terms of vapor pressures of the solid materials placed on the anodes and dissociation reactions of the molecules in the gaseous environment.

Gordon, W. A.↗

Emission spectrometric arcing procedure with minimal effect of chemical form of sample

This paper describes a study of matrix effects related to the chemical form of materials analyzed. The study was made using an arc in argon buffered with silver chloride. The effect of chemical form was minimal for a variety of metals, oxides, and carbides representing the most refractory compounds and thermally stable metal-containing molecules. Among these, only four of the most refractory materials known showed significant emission depressions due to incomplete volatilization in the arc system. These results are discussed in terms of vapor pressure of the solid materials placed on the anodes and dissociation reactions of the molecules in the gaseous environment.

Gordon, W. A.↗

Reducing energy consumption and carbon emissions of magnesia refractory products: A life-cycle perspective

China is the largest producer of magnesia refractory materials and products in the world, resulting in significant energy consumption and carbon emissions. This paper analyzes measures to reduce both the energy consumption and carbon emissions in the production phase and use phase, providing a theoretical basis for a sustainable magnesia refractory industry. Results show that the total carbon emissions of carbon-containing magnesia bricks produced with fused magnesia are much higher than those of other products, and the total carbon emissions of both general magnesia brick and magnesia-carbon spray are lower than those of other products. Carbon emissions of magnesia products are mainly concentrated in the production process of magnesia. Manufacturers should select materials with lower environmental impacts and emphasize saving energy and reducing carbon emissions in the magnesia production process. Through scenario analysis we found that CO 2 capture is an effective measure to reduce carbon emissions compared with just improving energy consumption. However, a robust CO 2 market does not currently exist. Policy makers should plan on integrating CO 2 capture in the magnesia industry into a regional CO 2 capture and storage development planning in the long term. In particular, magnesia production is concentrated in a single geographical area which would and thus could take advantage of significant scale effects. Finally, in the use phase, extending the service lifetime reduces carbon emissions over the product lifetime, thus users should attempt to extend the service lifetime of a furnace as a whole. However, results show that it is not advisable to add a large number of repair refractories to extend the lifetime of existing furnaces.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Innovative techniques for the production of energetic radicals for lunar materials processing including photogeneration via concentrated solar energy

A technique for photo generation of radicals is discussed that can be used in the recovery of oxygen and metals from extraterrestrial resources. The concept behind this work was to examine methods whereby radicals can be generated and used in the processing of refractory materials. In that regard, the focus is on the use of sunlight. Sunlight provides useful energy for processing in the forms of both thermal and quantum energy. A number of experiments were conducted in the chlorination of metals with and without the aid of UV and near UV light. The results of some of those experiments are discussed.

Osborn, D. E.↗

Hugoniot equation of state of anorthite glass and lunar anorthosite

Twenty-one Hugoniot experiments were conducted on an amorphous material of anorthite composition, in the pressure range 8-120 GPa, using both routine and new methods. Two Hugoniot measurements at about 120 GPa were made on lunar gabbroic anorthosite (Apollo 15,418). Theoretical Hugoniots are constructed for both materials assuming they are disproportionate to their component oxides. These accurately predict the P-p behavior of the lunar anorthosite Hugoniot at 120 GPa and the anorthite glass Hugoniot above 50 GPa, but overestimate the shock temperatures of anorthite glass. The mixed oxide model fails to predict the release paths of either material. It is concluded that the mixed oxide model is a good description of the bulk properties of the high-pressure phases of anorthite, but does not represent the actual phases. A significant enrichment of calcic refractory material in the earth's lower mantle is not precluded by the bulk properties of the anorthite high-pressure phases.

Boslough, M. B.↗

Metal- and intermetallic-matrix composites for aerospace propulsion and power systems

The requirements for high specific strength refractory materials of prospective military, civil, and space propulsion systems are presently addressed in the context of emerging capabilities in metal- and intermetallic-matrix composites. The candidate systems encompass composite matrix compositions of superalloy, Nb-Zr refractory alloy, Cu-base, and Ti-base alloy types, as well as such intermetallics as TiAl, Ti3Al, NiAl, and MoSi2. The brittleness of intermetallic matrices remains a major consideration, as does their general difficulty of fabrication.

Doychak, J.↗

Laboratory Studies of Extraterrestrial Ices and PAHs: Making an Astrobiological Silk Purse Out of An Interstellar Sow's Ear

Tremendous strides have been made in our understanding of interstellar material over the past twenty years thanks to significant, parallel developments in observational astronomy and laboratory astrophysics. Today, the composition of dust in the ISM is reasonably well constrained to cold, micron-sized particles of various refractory materials. Shrouded within the protective confines of cold, opaque molecular clouds--the birthplace of stars and planets--these particles secrete mantles of mixed molecular lees whose major components are also well constrained. Finally, amidst the molecular inventory of these ice mantles are likely to be found polycyclic aromatic hydrocarbons (PAHs), whose telltale infrared signature I is now recognized throughout the Universe. However, of what significance is this scenario to the origin of life in our solar system--or any other? The major components of the icy materials observed in interstellar clouds and in our own solar system are uniformly quite simple. In addition, despite the fact that PAHs likely represent the single largest molecular reservoir of organic carbon in evolving planetary systems, they are not what would be considered "biogenic" molecules. Although interesting from a chemical and astrophysical standpoint, in the absence of a mechanism by which these materials can be transformed into more biochemically significant structures, they are of little Astrobiological significance. In this talk, we will begin with a brief review of the nature and abundance of the "raw" population of PAHs and PAH-related materials in the ISM. From there, we will move on to explore our laboratory simulations of the photochemical evolution of realistic mixed molecular ices under conditions which simulate those encountered in the ISM and in evolving planetary systems. Particular attention will be paid to the surprisingly complex array of organic species that are produced in these ices from such a deceptively simple inventory of starting materials. In addition, we will explore the chemistry of PAHs under these conditions and consider its potential for transforming that rich repository of pre-biotic organic "ore" into materials of greater importance to Astrobiology.

Hudgins, Douglas M.↗

NBS: Materials measurements

Measurement of materials properties and thermophysical properties is described. The topics discussed are: surface tensions and their variations with temperature and impurities; convection during unidirectional solidification: measurement of high temperature thermophysical properties of tungsten liquid and solid; thermodynamic properties of refractory materials at high temperatures; and experimental and theoretical studies in wetting and multilayer adsorption.

Manning, J. R.↗

A high-pressure X-ray diffraction study of the crystalline phases in calcium aluminate cement paste

Calcium aluminate cement (CAC) has wide application in civil engineering and castable refractory materials. The main binding phases of hardened CAC paste, CaO·Al{sub 2}O{sub 3}·10H{sub 2}O (CAH{sub 10}), inevitably converts to 2CaO·Al{sub 2}O{sub 3}·8H{sub 2}O (C{sub 2}AH{sub 8}), 3CaO·Al{sub 2}O{sub 3}·6H{sub 2}O (C{sub 3}AH{sub 6}) and Al(OH){sub 3} (AH{sub 3}), leading to a significant change in the mechanical properties of the CAC matrix. This work investigates the mechanical properties of the main crystalline components in hydrated and/or converted CAC systems, using synchrotron-radiation-based high-pressure X-ray diffraction. The anisotropic deformations of CaAl{sub 2}O{sub 4} (CA), CAH{sub 10} and C{sub 3}AH{sub 6} along each crystallographic direction are investigated, along with their bulk moduli. The density-driven stiffening hypothesis is validated for the studied phases and other cement-based minerals. An atom-scale topological analysis is proposed to explain the unusually high stiffness of CAH{sub 10}. The results provide fundamental information to understand the mechanical properties of single cement-based phases at molecular level, and enable predicting the changing mechanical properties of converted CAC matrix using homogenization models.

36 MATERIALS SCIENCE↗

Attaching Metal Fasteners to Silica Tiles

Stress distributed so high load borne. Fastener bonded in densified hole or captured in plug of similar refractory material, which in turn bonded in hole in parent tile. Plug or bonding distributes mechanical load from fastener to broad region surrounding fastener, reducing local stress concentration and likelihood of breakage. Bonded-plug method has been successful in attaching mechanical fasteners to porous silica refractory tiles used on outer surface of Space Shuttle orbiter.

Holt, J. W.↗