Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Giant increase of critical current density and vortex pinning in Mn doped K{sub x}Fe{sub 2−y}Se{sub 2} single crystals

We report a comparative study of the critical current density (J{sub c}) and vortex pinning among pure and Mn doped K{sub x}Fe{sub 2−y}Se{sub 2} single crystals. It is found that the J{sub c} values can be greatly improved by Mn doping and post-quenching treatment when comparing to pristine pure sample. In contrast to pure samples, an anomalous second magnetization peak (SMP) effect is observed in both 1% and 2% Mn doped samples at T = 3 K for H∥ab but not for H∥c. Referring to Dew-Hughes and Kramer's model, we performed scaling analyses of the vortex pinning force density vs magnetic field in 1% Mn doped and quenched pristine crystals. The results show that the normal point defects are the dominant pinning sources, which probably originate from the variations of intercalated K atoms. We propose that the large nonsuperconducting K-Mn-Se inclusions may contribute to the partial normal surface pinning and give rise to the anomalous SMP effect for H∥ab in Mn doped crystals. These results may facilitate further understanding of the superconductivity and vortex pinning in intercalated iron-selenides superconductors.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Variation of effective filament diameter, irreversibility field, anisotropy, and pinning efficiency in Bi-2212 round wires

Abstract In recent years Bi 2 Sr 2 CaCu 2 O x (Bi-2212) received increasing attention due to its round wire multifilamentary architecture, a unique feature in high- T c superconductor. In fact, round wires are preferable for magnet designs, including solenoids for nuclear magnetic resonance (NMR) or research purpose and accelerator magnets. However, due to the narrow over-pressure heat treatment conditions necessary to obtain high J c and to the peculiar microstructure of Bi-2212 wires, a full understanding of the correlations between the different properties has not yet been developed. In this paper we investigate the effect of a vital part of Bi-2212 optimization, the maximum heat-treatment temperature T max in the range of 885 °C–896 °C, on the variations of J c , effective filament diameter d eff , anisotropy γ , INTER- and intra-grain irreversibility fields and pinning energies U 0 , all critical parameters in unravelling the complex mix of vortex pinning and connectivity that ultimately determines the critical current density. We found that d eff of the higher J c wires heat-treated at lower temperature is much smaller than for the lower J c wires. Moreover, a systematic increase of the irreversibility field and a decrease of the intrinsic Bi-2212 anisotropy underpins the higher J c . The analysis of the pinning energies reveals that there is little sample-to-sample variation in the INTER-grain pinning, whereas in all samples the intra-grain pinning has an enhancement below ∼40–45 K becoming more and more evident with increasing J c . These results suggest that the overall J c performance are not only related to the wire microstructure and connectivity, which obviously affect the INTER-grain properties, but they are also intimately related to the intrinsic and intra-grain properties such as γ and U 0 .

Physics↗

Creep-enhanced vortex pinning revealed through nonmonotonic relaxation of the Campbell length

Here, we study the effects of flux creep on the linear AC response of the vortex lattice in single crystals Ca 3 ⁢Ir 4 ⁢Sn 13 by measuring the Campbell penetration depth, 𝜆 C ⁡(𝑇,𝐻,𝑡) . Thermal fluctuations release vortices from shallow pinning sites, only for them to become re-trapped by deeper potential wells, causing an initial increase of the effective Labusch parameter, which is proportional to the pinning well curvature. This effect cannot be detected in conventional magnetic relaxation measurements but is revealed by our observation of a nonmonotonic time evolution of 𝜆 C ⁡(𝑇,𝐻,𝑡) , which directly probes the average curvature of the occupied pinning centers. The time evolution of 𝜆 C ⁡(𝑇,𝐻,𝑡) was measured at different temperatures in samples with different densities of pinning centers produced by electron irradiation. The curves can be collapsed together when plotted on a logarithmic time scale 𝑡 → 𝑇 ⁢ln ⁡(𝑡/𝑡 0 ) confirming that the time evolution is driven by flux creep. The 𝜆 C ⁡(𝑇,𝐻,𝑡) is hysteretic with a noticeable nonmonotonic relaxation in the presence of a vortex density gradient (after zero-field cooling), but is monotonic after field cooling, where the vortex density is uniform. This result quantitatively corroborates the novel picture of vortex creep based on the strong pinning theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thickness Dependence of Magnetic Relaxation and E-J Characteristics in Superconducting (Gd-Y)-Ba-Cu-O Films with Strong Vortex Pinning

The dependence of the critical current density Jc on temperature, magnetic field, and film thickness has been investigated in (Gd-Y)BaCu-oxide materials of 0.7, 1.4, and 2.8 m thickness. Generally, the Jc decreases with film thickness at investigated temperatures and magnetic fields. The nature and strength of the pinning centers for vortices have been identified through angular and temperature measurements, respectively. These films do not exhibit c-axis correlated vortex pinning, but do have correlated defects oriented near the ab-planes. For all film thicknesses studied, strong pinning dominates at most temperatures. The vortex dynamics were investigated through magnetic relaxation studies in the temperature range of 5 77 K in 1 T and 3 T applied magnetic fields, H || surface-normal. The creep rate S is thickness dependent at high temperatures, implying that the pinning energy is also thickness dependent. Maley analyses of the relaxation data show an inverse power law variation for the effective pinning energy Ueff ~ (J0/J) . Finally, the electric field-current density (E-J) characteristics were determined over a wide range of dissipation by combining experimental results from transport, swept field magnetometry (VSM), and Superconducting Quantum Interference Device (SQUID) magnetometry. We develop a self-consistent model of the combined experimental results, leading to an estimation of the critical current density Jc0(T) in the absence of flux creep.

42 ENGINEERING↗

Manipulation of individual superconducting vortices and stick-slip motion in periodic pinning arrays

We numerically examine the manipulation of superconducting vortices interacting with a moving trap representing a magnetic force tip translating across a superconducting sample containing a periodic array of pinning sites. As a function of the tip velocity and coupling strength, we find five distinct dynamic phases, including a decoupled regime where the vortices are dragged a short distance within a pinning site, an intermediate coupling regime where vortices in neighboring pinning sites exchange places, an intermediate trapping regime where individual vortices are dragged longer distances and exchange modes of vortices occur in the surrounding pins, an intermittent multiple trapping regime where the trap switches between capturing one or two vortices, and a strong coupling regime in which the trap permanently captures and drags two vortices. In some regimes we observe the counterintuitive behavior that slow moving traps couple less strongly to vortices than faster moving traps; however, the fastest moving traps are generally decoupled. The different phases can be characterized by the distances the vortices are displaced and the force fluctuations exerted on the trap. We find different types of stick-slip motion depending on whether vortices are moving into and out of pinning sites, undergoing exchange, or performing correlated motion induced by vortices outside of the trap. Finally, our results are general to the manipulation of other types of particle-based systems interacting with periodic trap arrays, such as colloidal particles or certain types of frictional systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical Flow Diagnostics of Counter Fluidization of Gravity-Driven Moving Packed Bed for a CSP Receiver Section Featuring Staggered Array of Cylindrical Pins

Particle fluidized beds have the potential to improve the efficiency of heat transfer in concentrated solar receiver furnace for use in next generation concentrated solar power (CSP) plants. This study presents an experimental investigation on the flow characterization of vertically downward moving packed bed with counter fluidization through an array of jets. To control the bubble size and its distribution in the bubbling fluidized bed, an array of cylindrical pin fins was arranged uniformly across the test article. The flow visualization was performed on the surface of transparent glass coated with electrically conductive materials for electrostatic dissipation purposes. The image acquisition was carried out via high-speed camera at a frequency of ~ 1kHz. The acquired images were analyzed in pairs with the help of a modern optical flow algorithm capable of calculating the movement of dense particle flow in the fluidized bed by tracking the light intensity of each predefined window of the frames. A comparison of fluidized beds with plane and pin-finned channels revealed distinct bubble behavior. Pin-finned channels were found to produce a larger number of small-sized bubbles, while plane channels generated fewer but larger bubbles at any given instant. The presence of pin fins was observed to reduce bubble size by preventing bubble merging and splitting larger bubbles when they encountered a pin.

concentrating solar power↗

Investigation of the decolorization efficiency of two pin-to-plate corona discharge plasma system for industrial wastewater treatment

In this article, a dual pin-to-plate high-voltage corona discharge system is introduced to study experimentally the gap distance, the contact time, the effect of pin and plate materials, the thickness of ground plate and the conductivity on the amount of Acid Blue 25 dye color removal efficiency from polluted water. A study for the optimum air gap distance between dual pin and surface of Acid Blue 25 dye solution is carried out using 3D-EM simulator to find maximum electric field intensity at the tip of both pins. The outcomes display that the best gap for corona discharge is approximately 5 mm for 15-kV source. This separation is constant during the study of other factors. In addition, an investigation of the essential reactive species responsible for oxidation of the dye organic compounds (O{sub 3} in air discharge, O{sub 3} in water, and H{sub 2}O{sub 2}) during the experimental time is conducted. Three various materials such as: stainless steel, copper and aluminum are used for pins and plate. The maximum color removal efficiencies of Acid Blue 25 dyes are 99.03, 82.04, and 90.78% after treatment time 15 min for stainless steel, copper, and aluminum, respectively. Measurement results for the impact of thickness of an aluminum ground plate on color removal competence show color removal efficiencies of 86.3, 90.78, and 98.06% after treatment time 15 min for thicknesses of 2, 0.5, and 0.1 mm, respectively. The increasing of the solution conductivity leads to the reduction of decolorization efficiency. A kinetic model is used to define the performance of corona discharge system. The models of pseudo-zero-order, pseudo-first-order, and pseudo-second-order reaction kinetics are utilized to investigate the decolorization of Acid Blue 25 dye. The rate of degradation of Acid Blue 25 dye follows the pseudo-first-order kinetics in the dye concentration.

36 MATERIALS SCIENCE↗

Critical and Subcritical Californium Source Driven Noise Analysis Experiments with Fresh PWR Fuels Pins

These experiments were performed in 1983 between August 1 and September 16 and used 35 operational days of critical facility time at the Babcock & Wilcox critical facility in Lynchburg, Va. These measurements were to assess the capability of the Cf source driven noise analysis method to measure the subcriticality of light water reactor fresh fuel configurations. This report documents the experiments of 1983 that were not reported at that time. These measurement with 2.459 wt. % 235 U enriched uranium oxide fresh fuel pins started at the delayed critical configuration of the fully assembled pressurized water reactor (PWR) core configuration with 1511 parts per million (ppm) natural boron (19.8 wt. % 10 B) in the water. This was a cylindrical configuration of 4961 fuel pins. After the initial measurements at delayed criticality, subcritical measurements by the Cf source driven noise analysis method were performed in which the number of detectors and Cf source locations were varied. Additional boron was added to the water moderator and reflector to reduce the neutron multiplication factor, with resulting boron concentrations of 1561, 1613, 1765, 1880, 2104, 2384, 2975, 3606, and 4303 ppm. After the completion of these measurements the increased, the boron concentration was returned to that at delayed critical (1511 ppm) and the reactivity was decreased by reducing the number of fuel pins in steps to 3713, 2553, 1281, 749, and 333 fuel pins and then to that (289) of a s ingle square 17 x 17 pin array, corresponding to a single PW fuel element. For all measurement that started at delayed criticality and then reduced the neutron multiplication factor to various subcritical states, inverse kinetics rod drop measurements at the higher reactivities were also performed but not reported here. At all subcritical states the break frequency noise analysis data was fitted to obtain the prompt neutron decay constant. Some data presented in this report are from notes not in the logbook. The purpose of this report is to document the experimental information for the measurements performed so that a later date someone could perform the required uncertainty and calculational analyses and documentation to use these data for an International Nuclear Criticality Safety Benchmark Program (INCSBEP) or Nuclear Energy Agency (NEA) benchmark. The data from these measurements is available from the Laboratory Records Department of Oak Ridge National Laboratory and the logbook is available from INCSBEP at Idaho National Laboratory.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fluctuations and Pinning for Individually Manipulated Skyrmions

We numerically examine the dynamics of individually dragged skyrmions interacting simultaneously with an array of other skyrmions and quenched disorder. For drives just above depinning, we observe a broadband noise signal with a 1/ f characteristic, while at higher drives, narrowband or white noise appears. Even in the absence of quenched disorder, the threshold force that must be applied to translate the driven skyrmion is finite due to elastic interactions with other skyrmions. The depinning threshold increases as the strength of the quenched disorder is raised. Above the depinning force, the skyrmion moves faster in the presence of quenched disorder than in a disorder-free system since the pinning sites prevent other skyrmions from being dragged along with the driven skyrmion. For strong pinning, we find a stick-slip motion of the driven skyrmion which produces a telegraph noise signature. The depinning threshold increases monotonically with skyrmion density in the absence of quenched disorder, but when pinning is present, the depinning threshold changes nonmonotonically with skyrmion density, and there are reentrant pinned phases due to a competition between pinning induced by the quenched disorder and that produced by the elastic interactions of the skyrmion lattice.

36 MATERIALS SCIENCE↗

Results of a preliminary experimental investigation of a vapor transport fuel pin

In-Pile experimental tests were conducted on two fuel pins mounted side-by-side in a holder assembly. The fuel pins consisted of stacked fully enriched UO2 pellets enclosed in a type 316 stainless steel clad 1/2 inch outside diameter and 3 inches in length. Each fuel pin contained four pellets for a total of 22 grams of fuel weight. The experiment was operated to maintain the maximum clad temperature at 395 K corresponding to a fuel temperature at the central void surface of 2350 K. Total primary coolant water flow past the pin holder was calculated to be 110 gallons per minute. Forty-four gallons per minute at a velocity of 36.5 feet per second flowed around each fuel pin. Calculations indicated the maximum heat flux was at the point of the highest temperature and was equal to 0.24 kW/sq cm or 7.62 Btu/hr sq ft. A series of high resolution neutron radiographs of the nuclear fueled vapor transport capsule was taken. The thermal neutrons emitted from the core of the 60 megawatt Plum Brook reactor facility were used.

Lanzo, C. D.↗

Irradiation of TZM: Uranium dioxide fuel pin at 1700 K

A fuel pin clad with TZM and containing solid pellets of uranium dioxide was fission heated in a static helium-cooled capsule at a maximum surface temperature of 1700 K for approximately 1000 hr and to a total burnup of 2.0 percent of the uranium-235. The results of the postirradiation examination indicated: (1) A transverse, intergranular failure of the fuel pin occurred when the fuel pin reached 2.0-percent burnup. This corresponds to 1330 kW-hr/cu cm, where the volume is the sum of the fuel, clad, and void volumes in the fuel region. (2) The maximum swelling of the fuel pin was less than 1.5 percent on the fuel-pin diameter. (3) There was no visible interaction between the TZM clad and the UO2. (4) Irradiation at 1700 K produced a course-grained structure, with an average grain diameter of 0.02 centimeter and with some of the grains extending one-half of the thickness of the clad. (5) Below approximately 1500 K, the irradiation of the clad produced a moderately fine-grained structure, with an average grain diameter of 0.004 centimeter.

Mcdonald, G. E.↗

Examination of T-111 clad uranium nitride fuel pins irradiated up to 13,000 hours at a clad temperature of 990 C

The examination of 27 fuel pins irradiated for up to 13,000 hours at 990 C is described. The fuel pin clad was a tantalum alloy with uranium nitride as the nuclear fuel. Two nominal fuel pin diameters were tested with a maximum burnup of 2.34 atom percent. Twenty-two fuel pins were tested for fission gas leaks; thirteen pins leaked. Clad ductility tests indicated clad embrittlement. The embrittlement is attributed to hydrogen from an n,p reaction in the fuel. Fuel swelling was burnup dependent, and the amount of fission gas release was low, generally less than 0.5 percent. No incompatibilities between fuel, liner, and clad were in evidence.

Slaby, J. G.↗

Stepped-Pin Clevis Resists Jamming

Pin modification allows pyrotechnic release devices to operate more smoothly. New clevis pin has stepped diameters to prevent bending as it exits yoke. In contrast, conventional unstepped clevis pin bends and jams as it is withdrawn. Stepped pin design suitable for explosive and possible hammer driven pin sullers.

Killgrove, T. O.↗

Stresses around holes in pin-loaded orthotropic plates

The effects of pin elasticity, pin/hole friction, and pin/hole clearance on the stresses around a hole in a pin-loaded orthotropic plate were studied. The problem was modeled as a planar problem, the pin and plate being two elastic bodies interacting through contact. Complex variable elasticity, a collocation scheme to enforce the pin/hole boundary conditions, and an iteration procedure to find the contact, slip, and no-slip regions were used to obtain numerical results. The results indicate that pin elasticity is not as important a variable as friction and clearance are. A rigid pin assumption, as opposed to the popular cosinusoidal radial traction, can be used without much error but clearance and friction should not be ignored.

Hyer, M. W.↗

Pin-loaded holes in large orthotropic plates

Pin-loaded holes commonly occur in engineering structures. However, accurate analysis of such holes presents formidable difficulties because of the load-dependent contact of the pin with the plate. Significant progress has recently been achieved in the analysis of holes in isotropic plates. This paper develops a simple and accurate method for the partial contact analysis of pin-loaded holes in composites. The method is based on an inverse formulation that seeks to determine loads in a given contact-separation configuration. A unified approach for all types of fit was used. Continuum solutions were obtained for infinitely large plates of various typical orthotropic properties with holes loaded by smooth rigid pins. These solutions were then compared with those for isotropic plates. The effects of orthotropy and the type of fit were studied through load-contact relationships, distribution of stresses and displacements, and their variation with load. The results are of direct relevance to the analysis and design of pin joints in composite plates.

Mangalgiri, P. D.↗

A technique for evaluating the application of the pin-level stuck-at fault model to VLSI circuits

Accurate fault models are required to conduct the experiments defined in validation methodologies for highly reliable fault-tolerant computers (e.g., computers with a probability of failure of 10 to the -9 for a 10-hour mission). Described is a technique by which a researcher can evaluate the capability of the pin-level stuck-at fault model to simulate true error behavior symptoms in very large scale integrated (VLSI) digital circuits. The technique is based on a statistical comparison of the error behavior resulting from faults applied at the pin-level of and internal to a VLSI circuit. As an example of an application of the technique, the error behavior of a microprocessor simulation subjected to internal stuck-at faults is compared with the error behavior which results from pin-level stuck-at faults. The error behavior is characterized by the time between errors and the duration of errors. Based on this example data, the pin-level stuck-at fault model is found to deliver less than ideal performance. However, with respect to the class of faults which cause a system crash, the pin-level, stuck-at fault model is found to provide a good modeling capability.

Palumbo, Daniel L.↗

Flux pinning characteristics and irreversibility line in high temperature superconductors

The flux pinning properties in high temperature superconductors are strongly influenced by thermally activated flux motion. The scaling relation of the pinning force density and the irreversibility line in various high temperature superconductors are numerically analyzed in terms of the flux creep model. The effect of two factors, i.e., the flux pinning strength and the dimensionality of the material, on these properties are investigated. It is speculated that the irreversibility line in Bi-2212 superconductors is one order of magnitude smaller than that in Y-123, even if the flux pinning strength in Bi-2212 is improved up to the level of Y-123. It is concluded that these two factors are equally important in determination of the flux pinning characteristics at high temperatures.

Matsushita, T.↗

Monolithically Integrated SiGe/Si PIN-HBT Front-End Transimpedance Photoreceivers

The demand for monolithically integrated photoreceivers based on Si-based technology keeps increasing as low cost and high reliability products are required for the expanding commercial market. Higher speed and wider operating frequency range are expected when SiGe/Si heterojunction is introduced to the circuit design. In this paper, a monolithic SiGe/Si PIN-HBT front-end transimpedance photoreceiver is demonstrated for the first time. For this purpose, mesa-type SiGe/Si PIN-HBT technology was developed. Fabricated HBTs exhibit f(sub max) of 34 GHz with DC gain of 25. SiGe/Si PIN photodiodes, which share base and collector layers of HBTs, demonstrate responsivity of 0.3 A/W at lambda=850 nm and bandwidth of 450 MHz. Based on these devices, single- and dual-feedback transimpedance amplifiers were fabricated and they exhibited the bandwidth of 3.2 GHz and 3.3 GHz with the transimpedance gain of 45.2 dB(Omega) and 47.4 dB(Omega) respectively. Monolithically integrated single-feedback PIN-HBT photoreceivers were implemented and the bandwidth was measured to be approx. 0.5 GHz, which is limited by the bandwidth of PIN photodiodes.

Rieh, J.-S.↗