Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

The effectiveness of D 2 pellet and gas injection in reducing intra-ELM tungsten erosion and heat flux in the DIII-D small angle slot divertor

Edge localized modes (ELMs) in H-mode plasmas can melt and erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes the use of D 2 pellet and gas injection for ELM mitigation on the DIII-D tokamak during the 2022 Small Angle Slot V-shaped Tungsten (W) (SAS-VW) divertor campaign, reducing W erosion and heat flux during ELMs. D α (656 nm) and WI (400.9 nm) filterscopes and Langmuir probes provide photon emission and electron density/temperature to estimate W atom erosion using the S/XB method, while surface eroding thermocouples measured ELM peak heat flux at the outer strike point (OSP). Thomson Scattering measurements of pedestal T e and n e provided input to predict W divertor erosion and heat flux during ELMs via the Free-Streaming plus Recycling Model (FSRM). While a greater D 2 mass injection rate decreased the ELM peak heat flux, the impact on W erosion was not monotonic. The average ‘large’ intra-ELM W erosion was lower for plasma shots with D 2 mass injection compared to the plasma shots without any D 2 mass injection in the SAS-VW divertor. However, plasma shots did not see significant changes in ‘large’ intra-ELM W divertor erosion as the D 2 mass injection rate increased. On average, the FSRM overestimated SAS-VW experimental intra-ELM W erosion by a factor of 6.9, but the overestimation is reduced to a factor of 3.6 with the implication of C deposition effects. Generally, experimentally measured and predicted quantities were worse for plasma shots with a lower D 2 mass injection rate and corresponding higher plasma carbon (C) impurity percentage (f C ). The discrepancies are postulated to be due to C/W material mixing, for which a simple analytic mixed-material model is presented. These results highlight the importance of incorporating and improving the robustness of a mixed-material layer model in the analysis of PFC erosion on present and future tokamak devices.

Carbon (C)↗
DOE OSTI2025

Comprehensive analysis of disruption mitigation methods using gas and pellet-like injections in ITER-like Tokamaks

Abstract Inert-gas shielding could be an effective mechanism for protection of plasma facing surfaces (PFS) against plasma particles impact and photon radiation heat loads during transient events in fusion devices. Neutral gas injection is one promising way to mitigate erosion of tokamak components and contamination. The objective of this work is to study and optimize mitigation methods using neutral gas and pellet-like injections to decrease the heat load to the divertor surfaces and to prevent vaporization of the various internal surfaces due to transient events in ITER-like devices. The integrated self-consistent models implemented in the HEIGHTS package was used for detailed analysis of the potential secondary plasma generation from the injected inert gas, its radiative characteristics, and shielding effectiveness. We varied the density, size, and location of an argon gas cloud to minimize the disruption energy deposited into the divertor components. We also investigated innovative ways for minor changes in ITER-like internal design to mitigate disruptions. We found the optimum parameters to fully protect ITER tokamak surfaces from erosion and vaporization during plasma instabilities. This preliminary analysis showed that using Ar gas injection methods could lead to enhancement in components lifetime in ITER-like and future DEMO devices with minor design changes.

Science & Technology - Other Topics↗
DOE OSTI2026

Effects of temperature and dose rate on ion-irradiated γ-LiAlO 2 pellets

Defect accumulation and microstructural evolution during ion irradiation at elevated temperatures are governed by competing processes of defect production, driven by the dose rate, and defect recovery, controlled by diffusion, interaction, and annihilation. Here, this study investigates the effects of irradiation temperature and the dose rate on microstructural evolution, deuterium retention, and lithium volatilization in γ-LiAlO 2 pellets subjected to sequential He + and D + ion irradiation. Experiments were performed to a total fluence of 3 × 10 17 (He + + D + )/cm 2 at 623, 673, 723, and 773 K with an average He + dose rate of 7.7 × 10 −4 dpa/s, and to 2 × 10 17 (He + + D + )/cm 2 at 773 K with dose rates of 6.8 × 10 −5 , 2.9 × 10 −4 , and 7.3 × 10 −4 dpa/s. At 623 K, the microstructure was dominated by cavities and fractures with no observable precipitate formation, while small precipitates emerged at 673 K. Increasing the irradiation temperature to 723–773 K promoted the formation of larger, faceted LiAl 5 O 8 precipitates, and surface amorphization, accompanied by pronounced lithium depletion and H–D isotopic exchange. At 773 K, medium and high dose rates produced an amorphized surface layer over a crystalline subsurface containing LiAl 5 O 8 precipitates and blisters at the crystalline–amorphous interface, whereas low-dose-rate irradiation preserved surface crystallinity with cavities distributed in the matrix, around precipitates, and along grain boundaries. Precipitate morphology was anisotropic with limited size dependence on the dose rate. These results elucidate the coupled effects of temperature and the dose rate and demonstrate that sequential He + and D 2 + irradiation at 773 K reproduces key microstructural features and H isotope behavior observed in neutron-irradiated γ-LiAlO 2 at 573 K.

dose rate effects↗
DOE OSTI2022

Physics of runaway electrons with shattered pellet injection at JET

Runaway electrons (REs) created during tokamak disruptions pose a threat to the reliable operation of future larger machines. Experiments using shattered pellet injection (SPI) have been carried out at the JET tokamak to investigate ways to prevent their generation or suppress them if avoidance is not sufficient. Avoidance is possible if the SPI contains a sufficiently low fraction of high-Z material, or if it is fired early in advance of a disruption prone to runaway generation. These results are consistent with previous similar findings obtained with Massive Gas Injection. Suppression of an already accelerated beam is not efficient using High-Z material, but deuterium leads to harmless terminations without heat loads. This effect is due to the combination of a large magnetohydrodynamic instability scattering REs on a large area and the absence of runaway regeneration during the subsequent current collapse thanks to the flushing of high-Z impurities from the runaway companion plasma. This effect also works in situations where the runaway beam moves upwards and undergoes scraping-off on the wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Interpretive MHD modeling of dispersive shell pellet injection for rapid shutdown in tokamaks

Dispersive shell pellet (DSP) injection is modeled with the extended-MHD code NIMROD for interpretive insight into the results of recent DIII-D DSP experiments and to explore the dynamics of an inside-out thermal quench for disruption mitigation in tokamaks. Simulations of the pre-thermal quench (TQ) phase indicate that the upper bound for the quantity of ablated carbon shell material that will not perturb the flux surfaces is in the ballpark of, but somewhat below the experimental quantity. Even below this quantity, sufficient electrons are added to the plasma by the shell material to produce significant dilution cooling before the TQ is triggered. Simulations carried through the end of the TQ have very large amplitude MHD fluctuations (δB/B>10 -2 ) at the time of the plasma current spike associated with current profile redistribution. Finally, after the plasma current spike, which is of comparable amplitude to that measured in DIII-D experiments, none of the runaway electron test-particles whose orbits are tracked throughout the simulation remain confined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

3D radiation, density, and MHD structures following neon shattered pellet injection into stable DIII-D Super H-mode discharges

Six nominally repeat neon shattered pellet injection (SPI) shutdowns of stable DIII-D Super H-modes are studied to understand the 3D properties of the radiation and impurity transport. The radiation efficiency and radiation peaking determine whether first wall melting is expected following disruption mitigation in ITER. Previous studies make use of axisymmetric approximations to infer radiation efficiencies, but validating the high efficiency required by ITER necessitates improved accuracy, and this work contributes by exploring the 3D radiation and density structures that will inform forward modeling. When the neon shatter plume produced by the SPI reaches the plasma edge, m/n = 3/1 and 2/1 island O-points are observed to align with the injection trajectory in five out of six cases, suggesting that the injected material seeds the island O-points. Field aligned neon structures emitting Ne-I line radiation drift at 1 km/s in the ion diamagnetic drift direction during the pre-TQ, tracking the motion of the m/n = 2/1 island O-point. Neon fragments penetrate to the q = 2 surface by the time of the TQ. Techniques to constrain the 3D emissivity are explored, and one method constrains a 3D flux tube that is consistent with the radiation data, and when mapped to the interferometers, intersects the lasers that measure the highest density. The resulting structure derived from the radiation measurements exists near the 2/1 island X-point. In five repeatable discharges, the peak of the radiation in the toroidal direction exists in a 120° toroidal sector where the injection occurs, in contrast with the outlier discharge where the toroidal peak exists in the complementary 240° toroidal sector far from the injector, and where a 50% lower density rise is observed. In conclusion, the n = 1 phase behavior is markedly different in the outlier discharge, suggesting a possible dependence of the radiation structure and the assimilation efficiency on MHD.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Experimental evidence of runaway electron tail generation via localized helical structure in pellet-triggered tokamak disruptions

A novel detector, using stacked BGO crystals, is developed for runaway electron (REs) studies in the DIII-D tokamak. It is able to resolve fast dynamics of high-energy tail formation of REs with an ultra-high time resolution of ~1 μs. As a cost, the detector estimates the `effective' energy of a given shape of γ-ray spectra and sacrifices the energy resolution. In aid of the new measurement capability, a rapid, inhomogeneous growth of RE tail is observed in detail during a major disruption triggered by an argon pellet. It is found that both the population and energy of a well-confined RE tail significantly oscillate at the early period of the growth. The oscillation phase is locked to a slow rotating magnetohydrodynamic instability, which is briefly destabilized for only ~1 ms at the early period of the current quench. The oscillation ceases promptly, when the mode disappears. As a result, the data suggests that the high-energy RE tail is well-confined and accelerated via a localized helical structure in the plasma core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

[LCA UP] Biomass Pelletization (2022)

This unit process quantifies the energy requirements that are expected to result from woody biomass or torrefied woody biomass pelletization.

Group - Basic Process↗
DOE OSTI2020

Documenting Development of Processing Parameters for Fabrication of Doped and Undoped Fuel Pellets (Summary Report)

Early FY20 restructuring of the TREAT work package FT-20LA02020608 Enriched Fuel Fabrication for Safety Testing, and associated deliverables necessitated the rescoping of existing LANL deliverables. This rescoped carryover report summarizes work to date on doped and undpoped fuel pellet fabrication development of proceeding parameters. This summary also includes a status update of intended research activities that fall under the activity associated with this work package.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Challenges and Advances in Aqueous Processing of Corn Stover Pellets into High Concentration Slurries

Significant progress has occurred in developing combined enzyme hydrolysis and fermentation technologies for transforming lignocellulosic feedstocks into ethanol and other bioproducts. Various routes described in the literature show that low carbon footprint processes efficiently convert the cellulose and hemicellulose fractions of pretreated corn stover, wood chips, and sugarcane bagasse to sugars and to ethanol.Combinations of different pretreatments at high or low pH or in liquid hot water, followed by enzyme hydrolysis and fermentation or direct conversion of cellulose to ethanol (i.e., by consolidated bioprocessing)have been demonstrated. These successes have brought the need to preparing the feedstock – before it enters the biorefinery – into focus. This paper summarizes recent developments in liquefying corn stover,before pretreatment, so that slurries with yield stresses below 200 Pa are obtained and a “pumpable” corn stover slurry results at initial solids loadings of up to 300 g/L. The manner in which corn stover pellets are combined with water and enzyme in an agitated bioreactor is described, and properties that define slurry behavior are presented. Implications on biorefinery operations are explained in terms of particle properties and the preprocessing of corn stover as well as the team approach used to obtain these results.

Wassgren, Carl↗
DOE OSTI2020

Coated U3Si2 pellets with enhanced water and steam oxidation resistance

A method of forming a water resistant boundary on a fissile material for use in a water cooled nuclear reactor is described. The method comprises coating the fissile material, such as a pellet of U3Si2 and/or the grain boundaries, to a desired thickness with a suitable coating material, such as atomic layer deposition or a thermal spray process. The coating material may be any non-reactive material with a solubility at least as low as that of UO2. Exemplary coating materials include ZrSiO4, FeCrAl, Cr, Zr, Al—Cr, CrAl, ZrO2, CeO2, TiO2, SiO2, UO2, ZrB2, Na2O—B2O3—SiO2—Al2O3 glass, Al2O3, Cr2O3, carbon, and SiC, and combinations thereof. The water resistant layer may be overlayed with a burnable absorber layer, such as ZrB2 or B2O3—SiO2 glass.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Simulating Catalysis with Realistic Pellet Geometries Using Mesoflow: A Case Study of Catalytic Propane Dehydrogenation

We present a case study of catalytic propane dehydrogenation with our open-source multiphysics solver, Mesoflow. The solver was developed to simulate reactive flow coupled to heterogeneous catalytic reactions and deactivation in the context of complex, mesoscale geometry. The method leverages cartesian block-structured adaptive mesh refinement to capture realistic catalyst microstructural features acquired directly from X-ray computed tomography data. A kinetic model for propane dehydrogenation and catalyst deactivation was developed based on temporal analysis of products (TAP) reactor experiments. The TAP reactor experiments allow for precise characterization of intrinsic kinetic reaction steps which are implemented into Mesoflow simulations to model the spatial and temporal evolution of reactants, products, and catalyst active sites. The short-term and long-term deactivation behavior is studied by using XCT data collected from fresh and aged catalyst pellets, which exhibit different microstructural features. This study employs time-splitting algorithms to connect disparate reaction and flow timescales, enabling the simulations to achieve realistic deactivation timescales on the order of minutes while the flow time-scales for small particles (100 microns) are several milliseconds. We also introduce a flexible automated python script that writes the necessary files to construct a Mesoflow simulation from user-created chemical mechanisms. We will also introduce a few new features that are added to Mesoflow such as higher order schemes, implicit chemistry integrators and the ability to run on AMD and NVIDIA graphics-processing-units.

AMReX↗
DOE OSTI2024

Toolpath considerations for extrusion: Pellet, filament, concrete, and thermoset

There are a variety of extrusion and deposition-based processes for additive manufacturing, such as fused deposition modeling (FDM), fused filament fabrication (FFF), and directed energy deposition (DED). These processes can use a variety of materials, including thermoplastic pellets, thermoplastic filament, thermoset, concrete, metal wire, metal powder, and more. For all these processes and materials, the underlying toolpath strategies for 3D-printing an object are the same: the object to be printed is sliced into layers, then the layer is optimally fit with toolpaths of a given width, based on specific user settings. However, based on the specific process being used, additional modifiers and toolpathing strategies may be employed to maximize the capabilities of the process and successfully construct an object. This chapter explores the different pathing considerations and additional strategies to be employed in extrusion processes that use thermoplastics, thermosets, and concretes.

Roschli, Alex↗
DOE OSTI2024

Mechanical Response of Cr-Coated Zircaloy-4 Cladding to Pellet-Cladding Interactions

Chromium-coated zircaloy is a promising accident tolerant fuel (ATF) cladding design which can help mitigate high temperature oxidation. The mechanical response of the cladding during and after loading may be altered by the Cr coating throughout anticipated operational and accident occurrences such as a pellet-cladding interaction (PCI). In this work, the mechanical behavior of Cr-coated and uncoated cold worked stress-relieved (CWSR) Zircaloy-4 (Zry-4) cladding to PCI loading conditions are studied. Stress relaxation tests are performed on CWSR Zry-4 cladding using full-tube axial tension and internal pressurization to investigate mechanical anisotropy and rate-limiting deformation mechanisms of the uncoated Zry-4. These results are compared to internal pressure testing results of similar cladding with physical vapor deposition (PVD) Cr-coating to reveal how the Cr-coating affects the cladding mechanical response. Findings are discussed in the context of ATF cladding performance during operation and storage.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Structure of the pellet-cladding interaction layer of a high-burnup Zr-Nb-O nuclear fuel cladding

Here, structure of the pellet/cladding-interaction (PCI) layer of a high-burnup nuclear fuel with niobium-bearing cladding was investigated using modern transmission electron microscopy (TEM) techniques. Morphology of the PCI consisted of uniform zirconia layer on the cladding side and finger-like features towards to the ceramic fuel. The PCI layer showed a complex microstructure that constitutes three distinct zirconia layers formed by two zirconia phases. From cladding to fuel, monoclinic, tetragonal, and another tetragonal phase were determined via TEM diffraction patterns and precession electron diffraction (PED) using ASTAR microscopy platform (AMP). Characterizations showed that monoclinic and tetragonal phases close to the cladding were crack-free, but the tetragonal layer adjacent to the fuel contained cracks and pores. Presence of the monoclinic layer suggested that its formation involved the gaseous diffusion of oxygen below threshold dose of fission product damage before the fuel/cladding contact occurred. Furthermore, high-resolution TEM revealed compound phase of (U,Zr)O 2 at fringes of zirconia fingers on the fuel side.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗