Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PARTIAL PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Measurement of Hydrogen Purge Rates in Parabolic Trough Receiver Tubes: Preprint

The purpose of this research is to investigate and develop methods to remove hydrogen centrally from commercial parabolic trough power plants. A mathematical model was developed that tracks the generation and transport of hydrogen within an operating plant. Modeling results predicted the steady-state partial pressure of hydrogen within the receiver annuli to be~1 torr. This result agrees withmeasured values for the hydrogen partial pressure. The model also predicted the rate at which hydrogen must be actively removed from the expansion tank to reduce the partial pressure of hydrogen within the receiver annuli to less than 0.001 torr. Based on these results, mitigation strategies implemented at operating parabolic trough power plants can reduce hydrogen partial pressure to acceptablelevels. Transient modeling predicted the time required to reduce the hydrogen partial pressures within receiver annuli to acceptable levels. The times were estimated as a function of bellows temperature, getter quantity, and getter temperature. This work also includes an experimental effort that will determine the time required to purge hydrogen from a receiver annulus with no getter.

14 SOLAR ENERGY↗

Measurement of partial vapor pressures of salt mixtures via combined horizontal transpiration and thermogravimetric analysis

A method combining thermogravimetric analysis (TGA) and horizontal transpiration with elemental analysis via inductively coupled plasma mass spectrometry or ion chromatography enabled calculation of partial pressures of individual salts in molten mixtures. TGA quantified total mass loss, while transpiration identified vapor-phase composition. Furthermore, two chloride (NaCl-MgCl 2 , NaCl-MgCl 2 + UCl 3 ) salts and one mixed halide (LiCl-LiF + Li 2 O) salt were analyzed at 750 °C and 550 °C, respectively. NaCl and MgCl 2 vapor pressures were 2.19–2.61 × 10 -4 atm and 2.47–2.48 × 10 -5 atm (dependent upon the identity of the invesitgated mixture); UCl 3 was 1.42 × 10 -7 atm. LiCl and LiF vapor pressures at 550 °C were 1.53 × 10 -6 and 6.32 × 10 -6 atm, respectively. Additionally, the TGA method was validated against values from the literature for unary LiCl and LiF.

36 MATERIALS SCIENCE↗

Zero added oxygen for high quality sputtered ITO: A data science investigation of reduced Sn-content and added Zr

The authors demonstrate mobilities of >45 cm{sup 2}/V s for sputtered tin-doped indium oxide (ITO) films at zero added oxygen. All films were deposited with 5 wt. % SnO{sub 2}, instead of the more conventional 8–10 wt. %, and had varying ZrO{sub 2} content from 0 to 3 wt. %, with a subsequent reduction in In{sub 2}O{sub 3} content. These films were deposited by radio-frequency magnetron sputtering from nominally stoichiometric targets with varying oxygen partial pressure in the sputter ambient. Anomalous behavior was discovered for films with no Zr-added, where a bimodality of high and low mobilities was discovered for nominally similar growth conditions. However, all films showed the lowest resistivity and highest mobilities when the oxygen partial pressure in the sputter ambient was zero. This result is contrasted with several other reports of ITO transport performance having a maximum for small but nonzero oxygen partial pressure. This result is attributed to the reduced concentration of SnO{sub 2}. The addition of ZrO{sub 2} yielded the highest mobilities at >55 cm{sup 2}/V s and the films showed a modest increase in optical transmission with increasing Zr-content.

36 MATERIALS SCIENCE↗

In Situ Measurement of Tritium Permeation Through Stainless Steel

The TMIST-2 irradiation experiment was conducted in the Advanced Test Reactor at Idaho National Laboratory to evaluate tritium permeation through Type 316 stainless steel (316 SS). The interior of a 316 SS seamless tube specimen was exposed to a 4He carrier gas mixed with a specified quantity of tritium (T2) to yield partial pressures of 0.1, 5, and 50 Pa at 292° and 330°C. In-situ tritium permeation measurements were made by passing a He-Ne sweep gas over the outer surface of the specimen to carry the permeated tritium to a bubbler column for liquid scintillation counting. An irradiation enhancement factor (IEF) was determined by comparing in-situ permeation data with a correlation for ex-reactor hydrogen permeation through austenitic stainless steel developed from literature data and reported by Le Claire. Nominal values for the IEF ranged between 3 and 5 for 316 SS. In-situ permeation data were also used to derive an in-reactor permeation correlation as a function of temperature and pressure. In addition, the triton recoil contribution to tritium permeation, which results from the transmutation of 3He to T, was also evaluated by introducing a 4He carrier gas mixed with 3He at a partial pressure of 1013 Pa at 330°C. Less than 3% of the tritium resulting from 3He transmutation contributed to tritium permeation.

In-Reactor↗

High rate reactive sputtering of MoN(x) coatings

High rate reactive sputtering of MoN(x) films was performed using feedback control of the nitorgen partial pressure. Coatings were made at four different target powers: 2.5, 5.0, 7.5 and 10 kW. No hysteresis was observed in the nitrogen partial pressure vs. flow plot, as is typically seen for the Ti-N system. Four phases were determined by X-ray diffraction: molybdenum, Mo-N solid solution, Beta-Mo2N and gamma-Mo2N. The hardness of the coatings depended upon composition, substrate bias, and target power. The phases present in the hardest films differed depending upon deposition parameters. For example, the Beta-Mo2N phase was hardest (load 25 gf) at 5.0 kW with a value of 3200 kgf/sq mm, whereas the hardest coatings at 10 kW were the gamma-Mo2N phase (3000 kgf/sq mm). The deposition rate generally decreased with increasing nitrogen partial pressure, but there was a range of partial pressures where the rate was relatively constant. At a target power of 5.0 kW, for example, the deposition rates were 3300 A/min for a N2 partial pressure of 0.05 - 1.0 mTorr.

Rudnik, Paul J.↗

Growth stress in tungsten carbide-diamond-like carbon coatings

Growth stress in tungsten carbide-diamond-like carbon coatings, sputter deposited in a reactive argon/acetylene plasma, has been studied as a function of the acetylene partial pressure. Stress and microstructure have been investigated by wafer curvature and transmission electron microscopy (TEM) whereas composition and energy distribution functions of positive ions were obtained by electron probe microanalyzer, elastic recoil detection analysis, and mass-energy analyzer (MEA). It has been observed that the compressive stress decreases with increasing acetylene partial pressure, showing an abrupt change from -5.0 to -1.6 GPa at an acetylene partial pressure of 0.012 Pa. TEM micrographs show that by increasing the acetylene partial pressure in the plasma from 0 to 0.012 Pa, the microstructure of the coating changes from polycrystalline to amorphous. MEA results show that the most probable energy of positive ions bombarding the substrate during deposition in pure argon and argon/acetylene atmosphere is the same. Based on the results, it is concluded that the huge variation in the compressive stress at low acetylene partial pressures is due to a change in the microstructure of the coating from polycrystalline to amorphous and not to the energy of positive ions bombarding the film.

36 MATERIALS SCIENCE↗

Physical conditions for UO formation in laser-produced uranium plumes

Laser-induced plasma spectroscopy is a powerful method for elemental detection and analysis, however the broadening and merging of densely packed spectral lines can make it especially challenging for studying high-Z elements such as uranium and other actinides. In order to understand the processes occurring in laser-induced plasma, it is necessary to evaluate the variation of its thermodynamic parameters. We performed spatiotemporal diagnostics of uranium species in plasma plumes produced by nanosecond near-infrared laser pulses in low- pressure environment. Spatially- and temporally-resolved emission spectroscopy experiments are supported by modeling of uranium emission and its persistence in the plume. Saha-Eggert equation as well as Boltzmann diagrams generated from numerous U I transitions are used to infer temperature. We report the rst measurements of uranium Stark broadening parameters for U I 499.01 nm and U II 500.82 nm transitions. The Stark widths of selected U transitions were measured by comparing their linewidths with the broadening of O I 777.19 nm line. Electron density was found to be on the order of 1016 cm??3, while the temperature was found to be in the range of 3000{8000 K. In addition to enhancing the fundamental understanding of high-Z plasmas under reduced-pressure environments, the knowledge of Stark broadening parameters could improve modeling capabilities and analytical performance of techniques that rely on emission plasma spectroscopy.

(140.3440) Laser-induced breakdown, (280.4788) Opt↗

Accelerated oxidation of epoxy thermosets with increased O 2 pressure

Polymer oxidation is usually accelerated with temperature, which is therefore applied in nearly every experimental approach dealing with predictive materials aging. Because of this simple approach, we may tend to neglect that the effective concentration of oxygen also acts as a rate multiplier for oxidation. Increasing the oxygen partial pressure in an aging environment accelerates oxidation, and while there is often a near proportional increase initially, the effect of additional oxygen usually transitions to a saturation level at some elevated pressure. This has been theoretically described in the general autoxidation scheme and is well recognized. However, for many materials the exact rate behavior under moderately increased oxygen concentration remains to be established. We therefore review epoxy oxidation and offer a broader overview of its behavior under increased O 2 partial pressure. Experimental data are given for a few thermoset materials demonstrating their rate behavior under O 2 partial pressure up to 4 atm, meaning approximately 20 times more than under standard atmospheric conditions. Confirmative evidence suggests that epoxy materials will reach saturation oxidation rates only at significantly higher O 2 partial pressure. In such a high-pressure regime it is theoretically possible to not only accelerate oxidation, but to transition into a condition where O 2 diffusion can be increased without further accelerating the oxidation rate. Finally, this can reduce diffusion limited oxidation effects under specific accelerated aging conditions as a combination of temperature and O 2 partial pressure.

36 MATERIALS SCIENCE↗

Oxidation and Condensation of Zinc Fume From Zn-CO 2 -CO-H 2 O Streams Relevant to Steelmaking Off-Gas Systems

Here the objective of this research was to study the condensation of zinc vapor to metallic zinc and zinc oxide solid under varying environments to investigate the feasibility of in-process separation of zinc from steelmaking off-gas dusts. Water vapor content, temperature, degree of cooling, gas composition, and initial zinc partial pressure were varied to simulate the possible conditions that can occur within steelmaking off-gas systems, limited to Zn-CO 2 -CO-H 2 O gas compositions. The temperature of deposition and the effect of rapidly quenching the gas were specifically studied. A homogeneous nucleation model for applicable experiments was applied to the analysis of the experimental data. It was determined that under the experimental conditions, oxidation of zinc vapor by H 2 O or CO 2 does not occur above 1108 K (835 °C) even for highly oxidizing streams (CO 2 /CO = 40/7). Rate expressions that correlate CO 2 and H 2 O oxidation rates to gas composition, partial pressure of water vapor, temperature, and zinc partial pressure were determined to be as follows: Rate $ \left(\frac{mol}{m^2s}\right) $ = 406 exp $ \left(\frac{-50.2 kJ/mol}{RT}\right) $ (pZnpCO 2 $-$ PCO/K eq CO 2 ) $\frac{mol}{m^2 x s}$ Rate $ \left(\frac{mol}{m^2s}\right) $ = 32.9 exp $ \left(\frac{-13.7 kJ/mol}{RT}\right) $ (pZnPH 2 O $-$ PH 2 /K eq H 2 O) $\frac{mol}{m^2 x s}$. It was proven that a rapid cooling rate (500 K/s) significantly increases the ratio of metallic zinc to zinc oxide as opposed to a slow cooling rate (250 K/s). SEM analysis found evidence of heterogeneous growth of ZnO as well as of homogeneous formation of metallic zinc. The homogeneous nucleation model fit well with experiments where only metallic zinc deposited. An expanded model with rates of oxidation by CO 2 and H 2 O as shown was combined with the homogenous nucleation model and then compared with experimental data. The calculated results based on the model gave a reasonable fit to the measured data. For the conditions used in this study, the rate equations for the oxidation of zinc by carbon dioxide and water vapor as well as the homogeneous nucleation model of metallic zinc were applicable for various temperatures, zinc partial pressures, CO 2 :CO ratios, and H 2 O partial pressures.

36 MATERIALS SCIENCE↗

Synthesis of low core loss Finemet/Ni0.5Zn0.5Fe2O4 composites by co-precipitation method

Highlights: • Finemet/NiZn ferrite composites were synthesized by co-precipitation method. • Magnetic properties can be adjusted by controlling oxygen partial pressure. • It shows lower core loss about 30.5 mW/cm{sup 3} at 100 kHz and 100 mT. - Abstract: Finemet/Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} core/shell structure composites have been prepared by a co-precipitation method followed by a high temperature sintering process. The formation mechanism of the core/shell structures and the effects of oxygen partial pressure during the sintering process on the phase structure, microstructure, and magnetic properties were discussed. Low and high oxygen partial pressures resulted in the formation of crystal defects and a reduction of the magnetic properties of the composites. The magnetic properties could be adjusted by controlling the oxygen partial pressure and the optimal magnetic properties of the composites were obtained by sintering under an oxygen partial pressure of 10%. The resulting composite exhibited a high permeability of 61, a high saturation magnetization of 135.5 emu/g and a low core loss of approximately 30.5 mW/cm{sup 3} at 100 kHz and 100 mT.

36 MATERIALS SCIENCE↗

Solution chemistry of Mo(III) and Mo(IV): Thermodynamic foundation for modeling localized corrosion.

To investigate the behavior of molybdenum dissolution products in systems that approximate localized corrosion environments, solubility of Mo(III) in equilibrium with solid MoO{sub 2} has been determined at 80 C as a function of solution acidity, chloride concentration and partial pressure of hydrogen. The measurements indicate a strong increase in solubility with acidity and chloride concentration and a weak effect of hydrogen partial pressure. The obtained results have been combined with literature data for systems containing Mo(III), Mo(IV), and Mo(VI) in solutions to develop a comprehensive thermodynamic model of aqueous molybdenum chemistry. The model is based on a previously developed framework for simulating the properties of electrolyte systems ranging from infinite dilution to solid saturation or fused salt limit. To reproduce the measurements, the model assumes the presence of a chloride complex of Mo(III) (i.e., MoCl{sup 2+}) and hydrolyzed species (MoOH{sup 2+}, Mo(OH){sup 2+}, and Mo(OH){sub 3}{sup 0}) in addition to the Mo{sup 3+} ion. The model generally reproduces the experimental data within experimental scattering and provides a tool for predicting the phase behavior and speciation in complex, concentrated aqueous solutions. Thus, it provides a foundation for simulating the behavior of molybdenum species in localized corrosion environments.

08 HYDROGEN↗

Steady-State Plant Model to Predict Hydroden Levels in Power Plant Components

The National Renewable Energy Laboratory (NREL) and Acciona Energy North America developed a full-plant steady-state computational model that estimates levels of hydrogen in parabolic trough power plant components. The model estimated dissolved hydrogen concentrations in the circulating heat transfer fluid (HTF), and corresponding partial pressures within each component. Additionally for collector field receivers, the model estimated hydrogen pressure in the receiver annuli. The model was developed to estimate long-term equilibrium hydrogen levels in power plant components, and to predict the benefit of hydrogen mitigation strategies for commercial power plants. Specifically, the model predicted reductions in hydrogen levels within the circulating HTF that result from purging hydrogen from the power plant expansion tanks at a specified target rate. Our model predicted hydrogen partial pressures from 8.3 mbar to 9.6 mbar in the power plant components when no mitigation treatment was employed at the expansion tanks. Hydrogen pressures in the receiver annuli were 8.3 to 8.4 mbar. When hydrogen partial pressure was reduced to 0.001 mbar in the expansion tanks, hydrogen pressures in the receiver annuli fell to a range of 0.001 mbar to 0.02 mbar. When hydrogen partial pressure was reduced to 0.3 mbar in the expansion tanks, hydrogen pressures in the receiver annuli fell to a range of 0.25 mbar to 0.28 mbar. Our results show that controlling hydrogen partial pressure in the expansion tanks allows us to reduce and maintain hydrogen pressures in the receiver annuli to any practical level.

14 SOLAR ENERGY↗

Cloud base levels for Jupiter and Venus and the heteromolecular nucleation theory

For purified binary gas mixtures like NH3-H2O or HCl-H2O, partial pressures appreciably greater than the two saturation partial pressures are needed to condense the gas mixture into small solution droplets (homogeneous heteromolecular nucleation). Thus without foreign nuclei, clouds are not as easily formed as in the theories of Lewis; the latter should be valid only if large condensation nuclei are available. We calculate here from classical homogeneous heteromolecular nucleation theory the threshold partial pressures necessary to achieve droplet nucleation for the gas mixtures NH3-H2O (Jupiter), HCl-H2O (Venus), H2SO4-H2O (Venus), and C2H5OH-H2O (laboratory).

Stauffer, D.↗

Enhancing thermochemical energy storage density of magnesium‐manganese oxides

Abstract Three approaches for enhancing the energy density of magnesium‐manganese oxide porous reactive materials for thermochemical energy storage (TCES) are investigated: adjusting the mole ratio, lowering the oxygen partial pressure during thermal reduction, and transition metal oxide doping. The manganese‐to‐magnesium molar ratios are varied to determine the composition yielding maximal energy density. The increase in energy density by lowering the oxygen partial pressure during the reduction step is also studied. Volumetric oxygen exchange capacities are measured for every case considered. Finally, the effects of doping magnesium‐manganese oxide with cobalt oxide, iron oxide, zinc oxide, and nickel oxide on the TCES properties are examined. We found the optimal Mn/Mg ratio for maximum volumetric energy density is in the vicinity of 1/1, achieving 1813 ± 175, 2178 ± 204, and 2323 ± 281 MJ m −3 for oxygen partial pressures of 0.2, 0.05, and 0.01 atm during thermal reduction, respectively; lowering the oxygen partial pressure below atmospheric during thermal reduction enhances oxygen exchange capacities and improves the energy density between 10%‐42% and 24%‐55% for oxygen partial pressures of 0.05 and 0.01 atm, respectively, with the greatest increases observed for high manganese content samples; and, doped samples exhibit reduced oxygen exchange and questionable reactive stability, thus appearing to reduce energy density.

King, Keith↗

Proton transfer reactions from H3/+/ ions to N2, O2, and CO molecules

The rate constants for proton transfer from H3(+) ions to N2, O2, and CO have been measured as function of hydrogen-buffer-gas partial pressure. The rate constant for proton transfer from H3(+) to N2 shows a very large pressure dependence, increasing from 1.0 by 10 to the -9th power cu cm/s at low H2 partial pressures to 1.7 by 10 to the -9th power cu cm/s at high H2 partial pressures. The rate constants for proton transfer from H3(+) to O2 and CO are constant with partial pressure of H2. The roles of excess vibrational energy in H3(+) ions and of equilibrium between forward and back reactions are discussed. Back reaction is observed only for the reaction of H3(+) ions with O2, and an equilibrium constant of 2.0 (plus or minus 0.4) at 298 K has been determined. From these data, the proton affinity of O2 is deduced to be 0.47 (plus or minus 0.11) kcal/mole higher than that of H2.

Kim, J. K.↗

Hydrogen Permeability of Incoloy 800H, Inconel 617, and Haynes 230 Alloys

A potential issue in the design of the NGNP reactor and high-temperature components is the permeation of fission generated tritium and hydrogen product from downstream hydrogen generation through high-temperature components. Such permeation can result in the loss of fission-generated tritium to the environment and the potential contamination of the helium coolant by permeation of product hydrogen into the coolant system. The issue will be addressed in the engineering design phase, and requires knowledge of permeation characteristics of the candidate alloys. Of three potential candidates for high-temperature components of the NGNP reactor design, the hydrogen permeability has been documented well only for Incoloy 800H, but at relatively high partial pressures of hydrogen. Hydrogen permeability data have been published for Inconel 617, but only in two literature reports and for partial pressures of hydrogen greater than one atmosphere, far higher than anticipated in the NGNP reactor. The hydrogen permeability of Haynes 230 has not been published. To support engineering design of the NGNP reactor components, the hydrogen permeability of Inconel 617 and Haynes 230 were determined using a measurement system designed and fabricated at the Idaho National Laboratory. The performance of the system was validated using Incoloy 800H as reference material, for which the permeability has been published in several journal articles. The permeability of Incoloy 800H, Inconel 617 and Haynes 230 was measured in the temperature range 650 to 950 °C and at hydrogen partial pressures of 10-3 and 10-2 atm, substantially lower pressures than used in the published reports. The measured hydrogen permeability of Incoloy 800H and Inconel 617 were in good agreement with published values obtained at higher partial pressures of hydrogen. The hydrogen permeability of Inconel 617 and Haynes 230 were similar, about 50% greater than for Incoloy 800H and with similar temperature dependence.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An overview of Japanese CELSS research activities

Development of Controlled Ecological Life Support System (CELSS) technology is inevitable for future long duration stays of human beings in space, for lunar base construction and for manned Mars flight programs. CELSS functions can be divided into 2 categories, Environmental Control and Material Recycling. Temperature, humidity, total atmospheric pressure and partial pressure of oxygen and carbon dioxide, necessary for all living things, are to be controlled by the environment control function. This function can be performed by technologies already developed and used as the Environment Control Life Support System (ECLSS) of Space Shuttle and Space Station. As for material recycling, matured technologies have not yet been established for fully satisfying the specific metabolic requirements of each living thing including human beings. Therefore, research activities for establishing CELSS technology should be focused on material recycling technologies using biological systems such as plants and animals and physico-chemical systems, for example, a gas recycling system, a water purifying and recycling system and a waste management system. Japanese research activities were conducted and will be continued accordingly.

Nitta, Keiji↗

Automation of closed environments in space for human comfort and safety

The Environmental Control and Life Support System (ECLSS) for the Space Station Freedom and future colonization of the Moon and Mars presents new challenges for present technologies. Current plans call for a crew of 8 to live in a safe, shirt-sleeve environment for 90 days without ground support. Because of these requirements, all life support systems must be self-sufficient and reliable. The ECLSS is composed of six subsystems. The temperature and humidity control (THC) subsystem maintains the cabin temperature and humidity at a comfortable level. The atmosphere control and supply (ACS) subsystem insures proper cabin pressure and partial pressures of oxygen and nitrogen. To protect the space station from fire damage, the fire detection and suppression (FDS) subsystem provides fire sensing alarms and extinguishers. The waste management (WM) subsystem compacts solid wastes for return to Earth, and collects urine for water recovery. Because it is impractical, if not impossible, to supply the station with enough fresh air and water for the duration of the space station's extended mission, these elements are recycled. The atmosphere revitalization (AR) subsystem removes CO2 and other dangerous contaminants from the air. The water recovery and management (WRM) subsystem collects and filters condensate from the cabin to replenish potable water supplies, and processes urine and other waste waters to replenish hygiene water supplies. These subsystems are not fully automated at this time. Furthermore, the control of these subsystems is not presently integrated; they are largely independent of one another. A fully integrated and automated ECLSS would increase astronauts' productivity and contribute to their safety and comfort. The Kansas State University Advanced Design Team is in the process of researching and designing controls for the automation of the ECLSS for Space Station Freedom and beyond. The approach chosen to solve this problem is to divide the design into three phases. The first phase is to research the ECLSS as a whole system and then concentrate efforts on the automation of a single subsystem. The AR subsystem was chosen for our focus. During the second phase, the system control process will then be applied to the AR subsystem.

Source record↗