Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Normal form methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Application of the method of integral relations to laminar boundary layers in three dimensions

The method of integral relations is extended to general three-dimensional compressible laminar boundary layer flows. The transformation employed to transform the basic three-dimensional compressible boundary layer equations into quasi-incompressible form is an extension of the Howarth transformation. The resulting system of differential equations is integrated numerically by the method of integral relations as proposed by Dorodnitsyn. To demonstrate the accuracy of the method, it is applied to calculation of the parabolic flow over a flat plate and the boundary flow over an infinite yawed cylinder, for which solutions are known. It is then applied to the flow over a flat plate disturbed by a cylinder normal to the plate, for which a finite-difference solution is available for comparison. It is finally applied to calculating the crossflow velocity variation for supersonic flow over a swept wedge.

Holt, M.↗
NASA NTRS1989

Computational simulation of transition to turbulence through inverse modeling

The present investigation has focused on a computational methodology for the fundamental case of transition in channel flow, in which recently published experimental data are utilized both as a stimulus and as a measure of merit of the method. The research has proceeded along three avenues in parallel. The first task has consisted of the development and verification of a computer code which calculates the mean evolution of flow in a channel similar to the one employed experimentally by Blair and Anderson. An analytical test case was created for the dual purposes of code verification and of highlighting the interactions between the Reynolds stress and the mean velocity profile. This test case generated a Reynolds stress by the residue in the momentum equation which is produced by a typical analytical velocity profile. By a substitution of this Reynolds stress into the appropriate code module, the correctness of the code may be verified, along with the accuracy of the computational method. The second task pursued has involved the development of a triple layer model for the Reynolds stress profile, which was suggested and derived from experimental velocity profiles. It is demonstrated that the innermost length scale is based on the local friction velocity, the intermediate layer corresponds to the usual logarithmic law of the wall region in which the normalized Reynolds stress is approximately unity, and the outermost layer is represented by a closed mathematical form depending explicitly on the velocity profile in the wake region. The third task was comprised of scrutiny of the excellent databases developed by Blair and others, and the planning of its incorporation into the transition analysis. These extensive measurements indicate that turbulent statistics in the transition regime may be considered to alternate between laminar and fully turbulent types, the proportions of which are quantified by a measured intermittency function.

Sepri, Paavo↗
NASA NTRS2011

Early Oscillation Detection for DC/DC Converter Fault Diagnosis

The electrical power system of a spacecraft plays a very critical role for space mission success. Such a modern power system may contain numerous hybrid DC/DC converters both inside the power system electronics (PSE) units and onboard most of the flight electronics modules. One of the faulty conditions for DC/DC converter that poses serious threats to mission safety is the random occurrence of oscillation related to inherent instability characteristics of the DC/DC converters and design deficiency of the power systems. To ensure the highest reliability of the power system, oscillations in any form shall be promptly detected during part level testing, system integration tests, flight health monitoring, and on-board fault diagnosis. The popular gain/phase margin analysis method is capable of predicting stability levels of DC/DC converters, but it is limited only to verification of designs and to part-level testing on some of the models. This method has to inject noise signals into the control loop circuitry as required, thus, interrupts the DC/DC converter's normal operation and increases risks of degrading and damaging the flight unit. A novel technique to detect oscillations at early stage for flight hybrid DC/DC converters was developed.

Wang, Bright L.↗
NASA NTRS2004

GPS FOM Chimney Analysis using Generalized Extreme Value Distribution

Many a time an objective of a statistical analysis is to estimate a limit value like 3-sigma 95% confidence upper limit from a data sample. The generalized Extreme Value Distribution method can be profitably employed in many situations for such an estimate. . .. It is well known that according to the Central Limit theorem the mean value of a large data set is normally distributed irrespective of the distribution of the data from which the mean value is derived. In a somewhat similar fashion it is observed that many times the extreme value of a data set has a distribution that can be formulated with a Generalized Distribution. In space shuttle entry with 3-string GPS navigation the Figure Of Merit (FOM) value gives a measure of GPS navigated state accuracy. A GPS navigated state with FOM of 6 or higher is deemed unacceptable and is said to form a FOM 6 or higher chimney. A FOM chimney is a period of time during which the FOM value stays higher than 5. A longer period of FOM of value 6 or higher causes navigated state to accumulate more error for a lack of state update. For an acceptable landing it is imperative that the state error remains low and hence at low altitude during entry GPS data of FOM greater than 5 must not last more than 138 seconds. I To test the GPS performAnce many entry test cases were simulated at the Avionics Development Laboratory. Only high value FoM chimneys are consequential. The extreme value statistical technique is applied to analyze high value FOM chimneys. The Maximum likelihood method is used to determine parameters that characterize the GEV distribution, and then the limit value statistics are estimated.

Ott, Rick↗
NASA NTRS1973

Development and application of vibroacoustic structural data banks in predicting vibration design and test criteria for rocket vehicle structures

A method of predicting broadband random vibration criteria for components on space vehicles is presented. Large amounts of vibration and acoustic data obtained from flights and static firing tests of space vehicle were formulated into vibroacoustic data banks for structural categories of ring frame, skin stringer, and honeycomb. The vibration spectra with their associated acoustic spectra are normalized to a reference acoustic spectrum. The individual normalized spectra are grouped according to definite structural characteristics and statistically analyzed to form the vibroacoustic data banks described in this report. These data banks represent the reference vibration criteria available for determining the new vehicle vibration criteria.

Bandgren, H. J.↗
NASA NTRS1983

The extreme nearfield of an acoustic diffraction grating

An expression for the transmitted sound field near (within a fraction of a wavelength) an array of slits is derived under the assumption that the normal component of the particle velocity is the same, in the slits, as if no grating were present and zero everywhere else in the plane of the grating. The expression is in the form of an inverse Fourier transform and can be evaluated quickly using a standard fast-Fourier-transform (FFT) algorithm. Using this technique, the sound pressure on the axis of symmetry normal to the grating was evaluated for a plane-wave incident at various angles with respect to the normal to the grating, and the results were found to provide an excellent qualitative (and to a significant degree quantitative) description of some experimental measurements. Extensions of the method to oscillating pistons of arbitrary (but planar) configuration in a rigid baffle are indicated.

Ochs, R. L., Jr.↗
NASA NTRS2018

All-Elastomer 3-Axis Contact Resistive Tactile Sensor Arrays and Micromilled Manufacturing Methods Thereof

At least one tactile sensor includes an insulating layer and a conductive layer formed on the surface of the insulating layer. The conductive layer defines at least one group of flexible projections extending orthogonally from the surface of the insulating layer. The flexible projections include a major projection extending a distance orthogonally from the surface and at least one minor projection that is adjacent to and separate from the major projection wherein the major projection extends a distance orthogonally that is greater than the distance that the minor projection extends orthogonally. Upon a compressive force normal to, or a shear force parallel to, the surface, the major projection and the minor projection flex such that an electrical contact resistance is formed between the major projection and the minor projection. A capacitive tactile sensor is also disclosed that responds to the normal and shear forces.

Charalambides, Alexandros↗
NASA NTRS2001

Sound Emission of Rotor Induced Deformations of Generator Casings

The casing of large electrical generators can be deformed slightly by the rotor's magnetic field. The sound emission produced by these periodic deformations, which could possibly exceed guaranteed noise emission limits, is analysed analytically and numerically. From the deformation of the casing, the normal velocity of the generator's surface is computed. Taking into account the corresponding symmetry, an analytical solution for the acoustic pressure outside the generator is round in terms of the Hankel function of second order. The normal velocity or the generator surface provides the required boundary condition for the acoustic pressure and determines the magnitude of pressure oscillations. For the numerical simulation, the nonlinear 2D Euler equations are formulated In a perturbation form for low Mach number Computational Aeroacoustics (CAA). The spatial derivatives are discretized by the classical sixth-order central interior scheme and a third-order boundary scheme. Spurious high frequency oscillations are damped by a characteristic-based artificial compression method (ACM) filter. The time derivatives are approximated by the classical 4th-order Runge-Kutta method. The numerical results are In excellent agreement with the analytical solution.

Polifke, W.↗
NASA NTRS2002

Thermocouple Boundary Layer Rake

Apparatus and method for providing a velocity flow profile near a reference surface. A measuring device utilizes a plurality of thermojunction pairs to provide the velocity flow profile in accordance with behavior of a gas relative to a constant thickness strut which stands vertically from the reference surface such that the span is normal to the surface, and the chord is parallel to the surface along the initial flow direction. Each thermojunction is carried on either side of a heater formed on a measuring surface in a constant thickness portion of a strut. Additionally, each thermojunction of a given pair is located at a predetermined height from the reference surface. Gas velocity data obtained from temperature differentials from one side of the heater to the other at each successive height is utilized to generate the velocity and turbulence level profiles.

Danny P Hwang↗
NASA NTRS2000

Monolithic integrated high-T.sub.c superconductor-semiconductor structure

A method for the fabrication of active semiconductor and high-temperature superconducting device of the same substrate to form a monolithically integrated semiconductor-superconductor (MISS) structure is disclosed. A common insulating substrate, preferably sapphire or yttria-stabilized zirconia, is used for deposition of semiconductor and high-temperature superconductor substructures. Both substructures are capable of operation at a common temperature of at least 77 K. The separate semiconductor and superconductive regions may be electrically interconnected by normal metals, refractory metal silicides, or superconductors. Circuits and devices formed in the resulting MISS structures display operating characteristics which are equivalent to those of circuits and devices prepared on separate substrates.

Burns, Michael J.↗
NASA NTRS2000

Method for making a monolithic integrated high-T.sub.c superconductor-semiconductor structure

A method for the fabrication of active semiconductor and high-temperature perconducting devices on the same substrate to form a monolithically integrated semiconductor-superconductor (MISS) structure is disclosed. A common insulating substrate, preferably sapphire or yttria-stabilized zirconia, is used for deposition of semiconductor and high-temperature superconductor substructures. Both substructures are capable of operation at a common temperature of at least 77 K. The separate semiconductor and superconductive regions may be electrically interconnected by normal metals, refractory metal silicides, or superconductors. Circuits and devices formed in the resulting MISS structures display operating characteristics which are equivalent to those of circuits and devices prepared on separate substrates.

Burns, Michael J.↗
NASA NTRS2024

Double Power-law Formation by Sequential Particle Acceleration

Spectral double power laws are common in solar high-energy phenomena such as flares and interplanetary energetic-electron events. However, the physical mechanism that produces the changes in power-law index within a single spectrum is unclear. We developed a fully analytical method of forming single power-law spectra from sequential acceleration of particles orbiting inside and hopping between simulated large-scale magnetic islands formed by flare reconnection. Here, we extend the analytical method to the formation of double power-law spectra by assuming sequential acceleration in two successive regions with different acceleration and particle-transport rates. The resulting spectral distribution is continuous and smooth, with a flattening at low energies, two power-law regions at mid-energies, and a steep rollover at high energies. The model provides analytical expressions for the spectral indices, all energy breaks, and normalization constants as functions of just three physical parameters of each acceleration region: (1) the energy gain in each accelerator, (2) the percentage of particles transferred between accelerators, and (3) the number of accelerators visited. One of the most salient predictions of our work is that the spectral index at high (low) energies is determined by the parameters of the first "seed" (second) acceleration region. By constructing the spectral distribution through an iterative analytical process, the evolution toward a double power law is easily characterized and explained. Our analytical model provides tools to interpret space- and ground-based observations from RHESSI, FOXSI, NuSTAR, Solar Orbiter/STIX, EOVSA, and future high-energy missions.

Solar flares↗
NASA NTRS1999

Investigation of Sooting in Microgravity Droplet Combustion: Fuel-Dependent Effects

Kumagai and coworkers first performed microgravity droplet combustion experiments [Kumagai, 1957]. The primary goal of these early experiments were to validate simple 'd(sup 2)-law models [Spalding, 1954, Godsave, 1954] Inherent in the 'd(sup 2) -law' formulation and in the scope of the experimental observation is the neglect of sooting behavior. In fact, the influence of sooting has not received much attention until more recent works [Choi et al., 1990; Jackson et al., 1991; Jackson and Avedisian, 1994; Choi and Lee, 1996; Jackson and Avedisian, 1996; Lee et al., 1998]:. Choi and Lee measured soot volume fraction for microgravity droplet flames using full-field light extinction and subsequent tomographic inversion [Choi and Lee, 1996]. In this investigation, soot concentrations were measured for heptane droplets and it was reported that soot concentrations were considerably higher in microgravity compared to the normal gravity flame. It was reasoned that the absence of buoyancy and the effects of thermophoresis resulted in the higher soot concentrations. Lee et al. [1998] performed soot measurement experiments by varying the initial droplet diameter and found marked influence of sooting on the droplet burning behavior. There is growing sentiment that sooting in droplet combustion must no longer be neglected and that "perhaps one of the most important outstanding contributions of (micro)g droplet combustion is the observation that in the absence of asymmetrical forced and natural convection, a soot shell is formed between the droplet surface and the flame, exerting an influence on the droplet combustion response far greater than previously recognized." [Law and Faeth, 1994]. One of the methods that we are exploring to control the degree of sooting in microgravity is to use different fuels. The effect of fuel structure on sooting propensity has been investigated for over-ventilated concentric coflowing buoyant diffusion flames. (Glassman, 1996]. In these investigations, the fuel flowrate was increased until smoke was observed to escape from the "luminous visible flame" [Glassman, 1996]. A total of 29 fuels were used in order to characterize relative sooting propensity. The sooting propensity of a particular fuel was assessed by comparing the flowrates for soot emission from the tip of the flame. It was reported that the sooting tendency for diffusion flames increased for fuels with higher rates of pyrolysis. Randolph and Law [1986 and not 1994] also examined the effect of fuel structure on droplet sooting behavior. In their experiments the droplets were separated from the bulk gas stream and quenched with nitrogen prior to gravimetric measurements. A variety of fuels were studied, namely aromatics, phenyl-alkanes and alkanes. The results were in qualitative agreement with the work of Glassman [1986]. Vander Wal et al. [1994] performed relative soot concentration measurements using laser-induced incandescence for heptane and decane fuel droplets burning under normal-gravity conditions. It was found that soot volume fractions for decane was more than a factor of two larger than that for heptane. Although the normal-gravity investigations have provided some important insights regarding the influence of fuel structure on the sooting behavior of droplet flames, results cannot be easily extrapolated for microgravity studies since increased residence times and thermophoretic effects must be considered in greater detail. Several studies have compared sooting behavior of different fuel droplets burning under microgravity conditions [Card and Choi, 1990; Jackson et al., 1991; Jackson and Avedisian, 1994], however, detailed quantitative results were not provided. In all of these previous studies, the degree of sooting was only visually assessed from an incandescent backlighted image of the soot containing region. Such techniques can provide misleading results regarding sooting behavior [Choi, 1996].

Manzello, Samuel L.↗
NASA NTRS1983

Method and technique for installing light-weight, fragile, high-temperature fiber insulation

A method of installing fragile, light weight, high temperature fiber insulation, particularly where the insulation is to be used as a seal strip providing a high order of thermal barrier insulation is discussed. The process is based on provision of a strip of the mineral batting cut oversize by a predetermined amount, saturated in a fugitive polymer solution, compressed in a mold, dried and cured to form a rigidized batting material which is machined to required shape. The machine dimensions would normally be at least nominally less than the dimensions of the cavity to be sealed. After insertion in the cavity, which may be a wire-mesh seal enclosure, the apparatus is subjected to baking at a temperature sufficiently high to cause the resin to burn off cleanly, leaving the batting substantially in its original condition and expanded into the cavity or seal enclosure.

Patel, B. C.↗
NASA NTRS1995

Ab Initio Characterization of Triatomic Bromine Molecules of Potential Interest in Stratospheric Chemistry

The equilibrium structures, harmonic vibrational frequencies, quadratic force fields, dipole moments, and IR intensities of several triatomic bromine compounds of known or potential importance in stratospheric ozone depletion chemistry have been determined using the CCSD(T) electron correlation method in conjunction with a basis set of triple zeta double polarized (TZ2P) quality. Specifically, the molecules included in the present study are HOBr, HBrO, FOBr, FBrO, BrNO, BrON, Br2O, BrBrO, BrCN, BrNC, ClOBr, ClBrO, and BrClO. Very accurate isomeric energy differences have also been determined at the CCSD(T) level with atomic natural orbital basis sets that include through g-type functions. In most cases, the isomer with a normal neutral Lewis dot structure is the lowest energy form, with the single exception that FBRO is predicted to be 11.1 kcal/mol (0 K) lower in energy than FOBr. In all cases, however, the hypervalent isomer is more stable relative to the isomer with a normal Lewis dot structure as compared to the chlorine analogs. Consistent with this observation, the energy of the last three molecules given above increases in the order ClOBr less than ClBrO less than BrClO. The CCSD(T)/TZ2P geometries and vibrational frequencies are in good agreement with the available experimental data. Heats of formation are determined for all species using a combination of theoretical isomeric, homodesmic, and isodesmic reaction energies. The accuracy of these quantities is ultimately dependent on the reliability of the experimental heat of formation of HOBr.

Lee. Timothy J.↗
NASA NTRS1995

Ab Initio Characterization of Triatomic Bromine Molecules of Potential Interest in Stratospheric Chemistry

The equilibrium structures, harmonic vibrational frequencies, quadratic force fields, dipole moments, and IR intensities of several triatomic bromine compounds of known or potential importance in stratospheric ozone depletion chemistry have been determined using the CCSD(T) electron correlation method in conjunction with a basis set of triple zeta double polarized (TZ2P) quality. Specifically, the molecules included in the present study are HOBr, HBrO, FOBr, FBrO, BrNO, BrON, Br2O, BrBrO, BrCN, BrNC, ClOBr, ClBrO, and BrClO. Very accurate isomeric energy differences have also been determined at the CCSD(T) level with atomic natural orbital basis sets that include through g-type functions. In most cases, the isomer with a normal neutral Lewis dot structure is the lowest energy form, with the single exception that FBrO is predicted to be 11.1 kcal/mol (0 K) lower in energy than FOBr. In all cases, however, the hypervalent isomer is more stable relative to the isomer with a normal Lewis dot structure as compared to the chlorine analogs. Consistent with this observation, the energy of the last three molecules given above increases in the order ClOBr less than ClBrO less than BrClO. The CCSD(T)/TZ2P geometries and vibrational frequencies are in good agreement with the available experimental data. Heats of formation are determined for all species using a combination of theoretical isomeric, homodesmic, and isodesmic reaction energies. The accuracy of these quantities is ultimately dependent on the reliability of the experimental heat of formation of HOBr.

Lee, Timothy J.↗
NASA NTRS1989

An experimental study of near wall flow parameters in the blade end-wall corner region

The near wall flow parameters in the blade end-wall corner region is investigated. The blade end-wall corner region was simulated by mounting an airfoil section (NACA 65-015 base profile) symmetric blades on both sides of the flat plate with semi-circular leading edge. The initial 7 cm from the leading edge of the flat plate was roughened by gluing No. 4 floor sanding paper to artificially increase the boundary layer thickness on the flat plate. The initial flow conditions of the boundary layer upstream of the corner region are expected to dictate the behavior of flow inside the corner region. Therefore, an experimental investigation was extended to study the combined effect of initial roughness and increased level of free stream turbulence on the development of a 2-D turbulent boundary layer in the absence of the blade. The measurement techniques employed in the present investigation included, the conventional pitot and pitot-static probes, wall taps, the Preston tube, piezoresistive transducer and the normal sensor hot-wire probe. The pitot and pitot-static probes were used to obtain mean velocity profile measurements within the boundary layer. The measurements of mean surface static pressure were obtained with the surface static tube and the conventional wall tap method. The wall shear vector measurements were made with a specially constructed Preston tube. The flush mounted piezoresistive type pressure transducer were employed to measure the wall pressure fluctuation field. The velocity fluctuation measurements, used in obtaining the wall pressure-velocity correlation data, were made with normal single sensor hot-wire probe. At different streamwise stations, in the blade end-wall corner region, the mean values of surface static pressure varied more on the end-wall surface in the corner region were mainly caused by the changes in the curvature of the streamlines. The magnitude of the wall shear stress in the blade end-wall corner region increased significantly in the close vicinity of the corner line. The maximum value of the wall shear stress and its location from the corner line, on both the surfaces forming the corner region, were observed to change along the corner. These observed changes in the maximum values of the wall shear stress and its location from the corner line could be associated with the stretching and attenuation of the horseshoe vortex. The wall shear stress vectors in the blade end-wall corner region were observed to be more skewed on the end-wall surface as compared to that on the blade surface. The differences in the wall shear stress directions obtained with the Preston tube and flow visualization method were within the range in which the Preston tube was found to be insensitive to the yaw angle.

Bhargava, Rakesh K.↗
NASA NTRS2004

Improved Phase-Mask Fabrication of Fiber Bragg Gratings

An improved method of fabrication of Bragg gratings in optical fibers combines the best features of two prior methods: one that involves the use of a phase mask and one that involves interference between the two coherent laser beams. The improved method affords flexibility for tailoring Bragg wavelengths and bandwidths over wide ranges. A Bragg grating in an optical fiber is a periodic longitudinal variation in the index of refraction of the fiber core. The spatial period (Bragg wavelength) is chosen to obtain enhanced reflection of light of a given wavelength that would otherwise propagate relatively unimpeded along the core. Optionally, the spatial period of the index modulation can be made to vary gradually along the grating (such a grating is said to be chirped ) in order to obtain enhanced reflection across a wavelength band, the width of which is determined by the difference between the maximum and minimum Bragg wavelengths. In the present method as in both prior methods, a Bragg grating is formed by exposing an optical fiber to an ultraviolet-light interference field. The Bragg grating coincides with the pattern of exposure of the fiber core to ultraviolet light; in other words, the Bragg grating coincides with the interference fringes. Hence, the problem of tailoring the Bragg wavelength and bandwidth is largely one of tailoring the interference pattern and the placement of the fiber in the interference pattern. In the prior two-beam interferometric method, a single laser beam is split into two beams, which are subsequently recombined to produce an interference pattern at the location of an optical fiber. In the prior phase-mask method, a phase mask is used to diffract a laser beam mainly into two first orders, the interference between which creates the pattern to which an optical fiber is exposed. The prior two-beam interferometric method offers the advantage that the period of the interference pattern can be adjusted to produce gratings over a wide range of Bragg wavelengths, but offers the disadvantage that success depends on precise alignment and high mechanical stability. The prior phase-mask method affords the advantages of compactness of equipment and relative insensitivity to both misalignment and vibration, but does not afford adjustability of the Bragg wavelength. The present method affords both the flexibility of the prior two-beam interferometric method and the compactness and stability of the prior phase-mask method. In this method (see figure), a laser beam propagating along the x axis is normally incident on a phase mask that lies in the (y,z) plane. The phase of light propagating through the mask is modulated with a spatial periodicity, p, along the y axis chosen to diffract the laser light primarily to first order at the angle . (The zero-order laser light propagating along the x axis can be used for alignment and thereafter suppressed during exposure of the fiber.) The diffracted light passes through a concave cylindrical lens, which converts the flat diffracted wave fronts to cylindrical ones, as though the light emanated from a line source. Then two parallel flat mirrors recombine the diffracted beams to form an interference field equivalent to that of two coherent line sources at positions A and B (virtual sources). The interference pattern is a known function of the parameters of the apparatus and of position (x,y) in the interference field. Hence, the tilt, wavelength, and chirp of the Bragg grating can be chosen through suitable adjustments of the apparatus and/or of the position and orientation of the optical fiber. In particular, the Bragg wavelength can be adjusted by moving the fiber along the x axis, and the bandwidth can be modified over a wide range by changing the fiber tilt angle or by moving the phase mask and/or the fiber. Alignment is easy because the zero-order beam defines the x axis. The interference is relatively stable and insensitive to the mechanical vibration because of the gh symmetry and compactness of the apparatus, the fixed positions of the mirrors and lens, and the consequent fixed positions of the two virtual line sources, which are independent of the translations of the phase mask and the laser relative to the lens.

Grant, Joseph↗