Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nonlinear reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

An active control system for helicopter vibration reduction by higher harmonic pitch

An analytical study defining the basic configuration of an active control system to reduce helicopter vibrations is presented. Theoretical results for a nonlinear four-bladed single rotor helicopter simulation are discussed, showing that vibration reductions on the order of 80-90% for airspeeds up to 150 kn can be expected when using a higher harmonic pitch in an active feedback control system. The rotor performance penalty associated with this level of vibration reduction is about 1-3% and the increase in rotor blade stresses is considered to be low. The location of sensor accelerometers proved to be significant for vibration reductions, and it is noted that the RTSA controller is tolerant of sensor signal noise.

Taylor, R. B.↗
DOE OSTI2024

Validation of a Tapered Impact Damper for Traffic Signal Structure Vibrations Using the Method of Harmonic Balance

Significant vibration amplitudes and cycles can be produced when traffic signal structures with low inherent damping are excited near one of their natural frequencies. For the mitigation of wind-induced vibrations, dynamic vibration absorbers coupled to the structure are often used. Here, this research investigates the performance of a tapered impact damper, consisting of a hanging spring-mass oscillator inside a housing capable of reducing vibration amplitude over a broader frequency range than the conventional tuned mass damper. A nonlinear, two degree-of-freedom model is developed with coordinates representing the traffic structure and the tapered impact damper. This research focuses on the application of the harmonic balance method to approximate the periodic solutions of the nonlinear equations to compute the nonlinear dynamics of the damped traffic signal structure. After designing and manufacturing a tapered impact damper, the traffic signal structure is tested with and without the damper using free vibration snapback tests. The experimental frequency and damping backbone curves are used to validate the analytical model, and the effectiveness of the damper is discussed.

42 ENGINEERING↗
DOE OSTI2024

Weak-form latent space dynamics identification

Recent work in data-driven modeling has demonstrated that a weak formulation of model equations enhances the noise robustness of a wide range of computational methods. In this paper, we demonstrate the power of the weak form to enhance the LaSDI (Latent Space Dynamics Identification) algorithm, a recently developed data-driven reduced order modeling technique. We introduce a weak form-based version WLaSDI (Weak-form Latent Space Dynamics Identification). WLaSDI first compresses data, then projects onto the test functions and learns the local latent space models. Notably, WLaSDI demonstrates significantly enhanced robustness to noise. With WLaSDI, the local latent space is obtained using weak-form equation learning techniques. Compared to the standard sparse identification of nonlinear dynamics (SINDy) used in LaSDI, the variance reduction of the weak form guarantees a robust and precise latent space recovery, hence allowing for a fast, robust, and accurate simulation. We demonstrate the efficacy of WLaSDI vs. LaSDI on several common benchmark examples including viscid and inviscid Burgers', radial advection, and heat conduction. For instance, in the case of 1D inviscid Burgers' simulations with the addition of up to 100% Gaussian white noise, the relative error remains consistently below 6% for WLaSDI, while it can exceed 10,000% for LaSDI. Similarly, for radial advection simulations, the relative errors stay below 15% for WLaSDI, in stark contrast to the potential errors of up to 10,000% with LaSDI. Moreover, speedups of several orders of magnitude can be obtained with WLaSDI. For example applying WLaSDI to 1D Burgers' yields a 140X speedup compared to the corresponding full order model.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

A Scale‐Adaptive Urban Hydrologic Framework: Incorporating Network‐Level Storm Drainage Pipes Representation

Abstract Below‐ground urban stormwater networks (BUSNs) significantly influence urban flood dynamics, yet their representation at the watershed or larger scales remains challenging. We introduce a scalable urban hydrologic framework that centers on a novel network‐level BUSN representation, balancing the needs for physical basis, parameter parsimony, and computational efficiency. Our framework conceptualizes an urban watershed into four interacting zones: hillslopes (natural), storm‐sewersheds (urban), a sub‐network channel (tributaries), and a main channel. We develop an innovative Graph Theory‐based algorithm to derive network‐level BUSN parameters from publicly available datasets, enabling efficient, scalable parameterization. We demonstrate this framework's applicability at nine representative watersheds in the Houston metropolitan region, USA, with urban imperviousness ranging from 0% to 64% and drainage areas ranging from 24 to 302 . Our model achieves satisfying computational efficiency, completing hourly time step simulations for 18 years in less than 5 sec per watershed on a standard PC. Validation against observed daily streamflow confirms that the model can capture small‐to‐large flood peaks and seasonal and annual water balance over these watersheds. Comparisons with the National Water Model show better performance in predicting flood peaks and overall water balance, underscoring the promises of our new framework for urban hydrologic modeling at large scales. Furthermore, analysis reveals nonlinear relationships between BUSNs' designed capacities and flood reduction effects. Our approach bridges the gap between detailed hydraulic and large‐scale hydrologic models, providing a valuable tool for urban flood prediction and management across broader spatial and temporal scales.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Local chromatic correction optics for Future Circular Collider e + e −

Local chromatic correction optics are proposed for the Future Circular e + − e − Collider. These new optics assume an identical layout of the magnets at all operation energies and include a new design for the arcs, for the straight sections, and for the final focus. The arcs design is a step forward from the classic FODO lattice that achieves near cancellation up to the fourth order of chromatic and geometric aberrations. Straight sections and the final focus benefit from the application of transparency conditions and are thus minimally impacting the global beam dynamics. The final focus design includes both vertical and horizontal chromaticity correction sections, crab sextupoles, and additional specific sextupoles and decapoles for the optimization of the dynamics off-energy. Decapoles are very effective in mitigating the reduction of dynamic aperture due to synchrotron radiation. Nonlinear magnet settings are further optimized with multiobjective algorithms. The overall properties of the new optics proposed are analyzed in the presence of errors and compared to other optics designs.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Weak-Form Latent Space Dynamics Identification

This software showcases the enhanced capabilities of the Latent Space Dynamics Identification (LaSDI) algorithm through the application of the weak form, resulting in WLaSDI. WLaSDI first compresses the data, then projects it onto test functions, and subsequently learns the local latent space models. Notably, WLaSDI demonstrates significantly improved robustness to noise. Using weak-form equation learning techniques, WLaSDI achieves local latent space modeling. Compared to the standard sparse identification of nonlinear dynamics (SINDy) used in LaSDI, the variance reduction of the weak form ensures robust and precise latent space recovery, enabling fast, robust, and accurate simulations. We demonstrate the efficacy of WLaSDI against LaSDI using several common benchmark examples, including viscid and inviscid Burgers', radial advection, and heat conduction. For instance, in 1D inviscid Burgers' simulations with up to 100% Gaussian white noise, WLaSDI maintains relative errors consistently below 6%, whereas LaSDI errors can exceed 10,000%. Similarly, in radial advection simulations, WLaSDI keeps relative errors below 16%, compared to potential errors of up to 10,000% with LaSDI. Additionally, WLaSDI achieves significant speedups, such as a 140X speedup in 1D Burgers' simulations compared to the corresponding full order model.

Choi, Youngsoo↗
DOE OSTI2021

Model Reduction by Generalized Falk Method for Efficient Field-Circuit Simulations

The Generalized Falk Method (GFM) for coordinate transformation, together with two model-reduction strategies based on this method, are presented for efficient coupled field-circuit simulations. Each model-reduction strategy is based on a decision to retain specific linearly-independent vectors, called trial vectors, to construct a vector basis for coordinate transformation. The reduced-order models are guaranteed to be stable and passive since the GFM is a congruence transformation of originally symmetric positive definite systems. We also show that, unlike the Pad´e-via-Lanczos (PVL) method, the GFM does not generate unstable positive poles while reducing the order of circuit problems. Further, the proposed GFM is also faster when compared to methods of the type Lanczos (or Krylov) that are already widely used in circuit simulations for electrothermal and electromagnetic problems. The concept of response participation factors is introduced for the selection of the trial vectors in the proposed model-reduction methods. Further, we present methods to develop simple equivalent circuit networks for the field component of the overall field-circuit system. The implementation of these equivalent circuit networks in circuit simulators is discussed. With the proposed model-reduction strategies, significant improvement on the efficiency of the generalized Falk method is illustrated for coupled field-circuit problems.

42 ENGINEERING↗
NASA NTRS1981

Urban air pollution and solar energy

The design and performance of solar energy systems for many potential applications (industrial/residential heat, electricity generation by solar concentration and photovoltaics) will be critically affected by local insolation conditions. The effects of urban air pollution are considered and reviewed. A study of insolation data for Alhambra, California (9 km south of Pasadena) shows that, during a recent second-stage photochemical smog alert (greater than or equal to 0.35 ppm ozone), the direct-beam insolation at solar noon was reduced by 40%, and the total global by 15%, from clean air values. Similar effects have been observed in Pasadena, and are attributable primarily to air pollution. Effects due to advecting smog have been detected 200 km away, in the Mojave Desert. Preliminary performance and economic simulations of solar thermal and photovoltaic power systems indicate increasing nonlinear sensitivity of life cycle plant cost to reductions in insolation levels due to pollution.

Gammon, R. B.↗
NASA NTRS1990

Fighter agility metrics

Fighter flying qualities and combat capabilities are currently measured and compared in terms relating to vehicle energy, angular rates and sustained acceleration. Criteria based on these measurable quantities have evolved over the past several decades and are routinely used to design aircraft structures, aerodynamics, propulsion and control systems. While these criteria, or metrics, have the advantage of being well understood, easily verified and repeatable during test, they tend to measure the steady state capability of the aircraft and not its ability to transition quickly from one state to another. Proposed new metrics to assess fighter aircraft agility are collected and analyzed. A framework for classification of these new agility metrics is developed and applied. A complete set of transient agility metrics is evaluated with a high fidelity, nonlinear F-18 simulation. Test techniques and data reduction methods are proposed. A method of providing cuing information to the pilot during flight test is discussed. The sensitivity of longitudinal and lateral agility metrics to deviations from the pilot cues is studied in detail. The metrics are shown to be largely insensitive to reasonable deviations from the nominal test pilot commands. Instrumentation required to quantify agility via flight test is also considered. With one exception, each of the proposed new metrics may be measured with instrumentation currently available.

Liefer, Randall K.↗
NASA NTRS1990

Assessment of proposed fighter agility metrics

This paper presents the results of an analysis of proposed metrics to assess fighter aircraft agility. A novel framework for classifying these metrics is developed and applied. A set of transient metrics intended to quantify the axial and pitch agility of fighter aircraft is evaluated with a high fidelity, nonlinear F-18 simulation. Test techniques and data reduction method are proposed, and sensitivities to pilot introduced errors during flight testing is investigated. Results indicate that the power onset and power loss parameters are promising candidates for quantifying axial agility, while maximum pitch up and pitch down rates are for quantifying pitch agility.

Liefer, Randall K.↗
NASA NTRS1999

Efficient Implementations of the Quadrature-Free Discontinuous Galerkin Method

The efficiency of the quadrature-free form of the dis- continuous Galerkin method in two dimensions, and briefly in three dimensions, is examined. Most of the work for constant-coefficient, linear problems involves the volume and edge integrations, and the transformation of information from the volume to the edges. These operations can be viewed as matrix-vector multiplications. Many of the matrices are sparse as a result of symmetry, and blocking and specialized multiplication routines are used to account for the sparsity. By optimizing these operations, a 35% reduction in total CPU time is achieved. For nonlinear problems, the calculation of the flux becomes dominant because of the cost associated with polynomial products and inversion. This component of the work can be reduced by up to 75% when the products are approximated by truncating terms. Because the cost is high for nonlinear problems on general elements, it is suggested that simplified physics and the most efficient element types be used over most of the domain.

Lockard, David P.↗
DOE OSTI2024

Machine-learning based model reduction for partial differential equations

We develop a novel synergistic approach between model reduction and machine learning. The specific goal of this project is to aid in the construction of reduced order models for basis functions that are custom-made to represent the solution of partial differential equations. Partial differential equations (PDEs) are one of the main mathematical tools for describing physical phenomena. However, due to either efficiency or necessity, for many real-world problems, we are interested in constructing reduced order models (ROMs) which focus only on the explicit computation of subsets of the active spatio-temporal scales in the problem, while treating the interaction with the rest of the scales approximately. The task of accurate representation of such interactions (usually called memory terms) constitutes a vast area of research known as model reduction. PI Stinis has significant expertise in the construction of ROMs for complex systems. In addition, in recent work with the project key participant Qadeer, they have utilized machine learning to acquire custom-made basis functions (CBFs) to expand the solutions of PDEs. In the proposed work, we will merge the two concepts by constructing ROMs for subsets of the CBFs needed to represent the solution of a PDE. Specifically, we will use the Mori-Zwanzig model reduction formalism to construct ROMs for subsets of CBFs for nonlinear PDEs of various complexity, as well as investigate the usage of CBFs in the spectral vanishing viscosity method for problems that can form shocks in finite time. The outcome of the research is aimed to be proof-of-concept about a novel synergistic approach between model reduction and machine learning, thus advancing the field of scientific machine learning. Such a capability will benefit the efficient modeling of physical systems appearing in various areas of interest to the DOE.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

A Realistic Theory of Quantum Measurement

Abstract We propose that the ontic understanding of quantum mechanics can be extended to a fully realistic theory that describes the evolution of the wavefunction at all times, including during a measurement. In such an approach the wave equation should reduce to the standard wave equation when there is no measurement, and describe state reduction when the system is measured. The general wave equation must be nonlinear and nonlocal, and we require it to be time-symmetric; consequently, this approach is not a new interpretation but a new theory. The wave equation is an integrodifferential equation (IDE). The time symmetry requirement leads to a retrocausal approach, in which the wave equation is solved subject to initial and final conditions to determine history at intermediate times. We propose that different outcomes from (apparently) identically prepared experiments may result from uncontrolled parameters; both the nonlocality and the retrocausality of the theory imply that Bell’s Theorem cannot rule out such “hidden variables.” Beginning with Hamilton’s principle, we demonstrate the construction of such a theory by replacing the action with a functional designed to give rise to a nonlinear, nonlocal IDE as the wave equation. This IDE reduces to the standard wave equation (a differential equation) in the absence of a measurement, but exhibits state reduction to a single eigenvalue when the system interacts with another system with the properties of a measurement apparatus. We demonstrate several desirable features of this theory; for other properties we indicate their plausibility and possible avenues to a proof.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1991

Coupled rotor-flexible fuselage vibration reduction using open loop higher harmonic control

A fundamental study of vibration prediction and vibration reduction in helicopters using active controls was performed. The nonlinear equations of motion for a coupled rotor/flexible fuselage system have been derived using computer algebra on a special purpose symbolic computer facility. The trim state and vibratory response of the helicopter are obtained in a single pass by applying the harmonic balance technique and simultaneously satisfying the trim and the vibratory response of the helicopter for all rotor and fuselage degrees of freedom. The influence of the fuselage flexibility on the vibratory response is studied. It is shown that the conventional single frequency higher harmonic control is capable of reducing either the hub loads or only the fuselage vibrations but not both simultaneously. It is demonstrated that for simultaneous reduction of hub shears and fuselae vibrations a new scheme called multiple higher harmonic control is required.

Papavassiliou, I.↗
DOE OSTI2025

Microtearing stability and turbulence in the pedestal: Linear gyrokinetics, reduced models, and nonlinear turbulent transport

Microtearing modes can play a crucial role in electron heat transport in tokamak plasmas, affecting both energy confinement and overall performance. This study investigates microtearing modes (MTM) stability and turbulence in a JET pedestal through gyrokinetic simulations using the Gene code, complemented by a reduced eigenvalue model. The focus is on how MTM properties depend on key plasma parameters, including collisionality and plasma beta β—the ratio of plasma pressure to magnetic pressure—the normalized toroidal wavenumber k y ρ s ⁠, where ρ s denotes the ion sound gyroradius (typically a few millimeters in edge plasmas) and isotope mass. Collisionality enhances MT growth rates, while increasing β leads to a shift from MTMs to kinetic-ballooning modes, typically for k y ρ s ⁠, where ρ s ≲ 0.2⁠. A purely collisionless branch of MTMs persists at low k y ρ s ⁠, where ρ s with distinctive properties including non-negligible particle flux and ion thermal transport. Isotope mass scans reveal modest reduction of MTM growth rates as ion mass decreases. Nonlinear simulations produce experimentally relevant transport levels. Numerical experiments turning off zonal flows and fields identify the critical role of zonal flows and zonal fields in regulating MTM turbulence. Their removal leads to a significant increase in electron heat flux. These findings provide new insight into MTM-driven transport and its impact on tokamak confinement and lay a foundation for reduced modeling and predictive capabilities.

Electrostatics↗
NASA NTRS1990

A study of coupled rotor-fuselage vibration with higher harmonic control using a symbolic computing facility

A fundamental study of vibration prediction and vibration reduction in helicopters using active controls was performed. The nonlinear equations of motion for a coupled rotor/flexible fuselage system have been derived using computer algebra on a special purpose symbolic computing facility. The details of the derivation using the MACSYMA program are described. The trim state and vibratory response of the helicopter are obtained in a single pass by applying the harmonic balance technique and simultaneously satisfying the trim and the vibratory response of the helicopter for all rotor and fuselage degrees of freedom. The influence of the fuselage flexibility on the vibratory response is studied. It is shown that the conventional single frequency higher harmonic control (HHC) capable of reducing either the hub loads or only the fuselage vibrations but not both simultaneously. It is demonstrated that for simultaneous reduction of hub shears and fuselage vibrations a new scheme called multiple higher harmonic control (MHHC) is required. The fundamental aspects of this scheme and its uniqueness are described in detail, providing new insight on vibration reduction in helicopters using HHC.

Papavassiliou, I.↗
DOE OSTI2022

Physics-informed regularization and structure preservation for learning stable reduced models from data with operator inference

Operator inference learns low-dimensional dynamical-system models with polynomial nonlinear terms from trajectories of high-dimensional physical systems (non-intrusive model reduction). Here, this work focuses on the large class of physical systems that can be well described by models with quadratic and cubic nonlinear terms and proposes a regularizer for operator inference that induces a stability bias onto learned models. The proposed regularizer is physics informed in the sense that it penalizes higher-order terms with large norms and so explicitly leverages the polynomial model form that is given by the underlying physics. This means that the proposed approach judiciously learns from data and physical insights combined, rather than from either data or physics alone. Additionally, a formulation of operator inference is proposed that enforces model constraints for preserving structure such as symmetry and definiteness in linear terms. Numerical results demonstrate that models learned with operator inference and the proposed regularizer and structure preservation are accurate and stable even in cases where using no regularization and Tikhonov regularization leads to models that are unstable.

97 MATHEMATICS AND COMPUTING↗