Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MIXTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Fanning - A classification algorithm for mixture landscapes applied to Landsat data of Maine forests

It is pointed out that typical landscapes include a relatively small number of 'pure' land cover types which combine in various proportions to form a myriad of mixture types. Most Landsat classifications algorithms used today require a separate user specification for each category, including mixture categories. Attention is given to a simpler approach, which would require the user to specify only the 'pure' types. Mixture pixels would be classified on the basis of the proportion of the area covered by each pure type within the pixel. The 'fanning' algorithm quantifies varying proportions of two 'pure' land cover types in selected mixture pixels. This algorithm was applied to 200,000 ha of forest land in Maine, taking into account a comparison with standard inventory information. Results compared well with a discrete categories classification of the same area.

Ungar, S. G.↗
NASA NTRS1983

An experimental study of adsorption interference in binary mixtures flowing through activated carbon

The isothermal transmission through activated carbon adsorber beds at 25 C of acetaldehyde-propane and acetylene-ethane mixtures in a helium carrier gas was measured. The inlet concentration of each component was in the range between 10 ppm and 500 ppm. The constant inlet volumetric flow rate was controlled at 200 cc (STP)/min in the acetaldehyde-propane experiments and at 50 cc (STP)/min in the acetaldehyde-ethane experiments. Comparison of experimental results with the corresponding single-component experiments under similar conditions reveals interference phenomena between the components of the mixtures as evidenced by changes in both the adsorption capacity and the dispersion number. Propane was found to displace acetaldehyde from the adsorbed state. The outlet concentration profiles of propane in the binary mixtures tend to become more diffuse than the corresponding concentration profiles of the one-component experiments. Similar features were observed with mixtures of acetylene and ethane; however, the displacement of acetylene by ethane is less pronounced.

Madey, R.↗
NASA NTRS1983

Estimating proportions of materials using mixture models

An approach to proportion estimation based on the notion of a mixture model, appropriate parametric forms for a mixture model that appears to fit observed remotely sensed data, methods for estimating the parameters in these models, methods for labelling proportion determination from the mixture model, and methods which use the mixture model estimates as auxiliary variable values in some proportion estimation schemes are addressed.

Heydorn, R. P.↗
NASA NTRS1982

Statistical mechanics of dilute liquid mixtures of He3 in He4

The Woo-Tan-Massey quantum-mechanical theory of dilute mixtures of He-3 in liquid He-4 is extended to incorporate superfluid flow. Then statistical-mechanical principles are employed to find explicit formulas for thermodyanmic and hydrodynamic properties of mixtures, such as internal energy, free energy, entropy, pressure, chemical potential, and normal-fluid and superfluid densities. This paper is the first in a planned series that applies methods originally developed for pure liquid He-4 to dilute mixtures as a means of establishing a comprehensive theory that includes a theoretical bridge between a microscopic description of the mixtures and a hydrodynamic two-fluid model. Ultimately effects of applied electric and magnetic fields on dilute solutions are also planned to be treated.

Jackson, H. W.↗
NASA NTRS1983

Studies of proton-irradiated cometary-type ice mixtures

Cometary ice mixtures are studied in a laboratory experiment designed to simulate the temperature, pressure and radiation environments of the interstellar Oort cloud region, in order to test the hypothesized radiation synthesis mechanism for changing the characteristics of the outer few meters of a comet stored in the Oort cloud for 4.6 billion years. All experiments conducted confirm the synthesis of new molecular species in solid phase mixtures at 20 K. When CH4 is present in the irradiated ice mixture, long chained, voltaile hydrocarbon and CO2 are synthesized together with high molecular weight C compounds present in the room temperature residue. Due to radiation synthesis, about 1 percent of the ice was converted into a nonvolatile residue containing complicated C compounds not present in the blank samples. These results suggest that initial molecular abundances can be altered, and new species created, as a result of radiation synthesis. Irradiated mixtures exhibited thermoluminescence and pressure enhancements during warming, showing the synthesis of reactive species. Outbursts in new comets resulting from similar irradiation-induced exothermic activity would be expected to begin occurring at distances of the order of 100 AU.

Moore, M. H.↗
NASA NTRS1982

Can crop types be resolved using mixture distribution components - Some initial results and implications

For the analysis of remotely sensed data, it is frequently necessary to design a classifier in order to locate a ground cover class of interest or to estimate the proportion of this ground cover class. Advantages of a mixture distribution formulation are discussed, and a description is presented of the results of estimating the proportion of small grains in ten Landsat data segments using the mixture model. It is found that the mixture model proportion estimates have a very low variance and coefficient of variation. The discussed investigation implies that the mixtures model is a viable method for determining the distributions of classes of interest in remote sensing problems and in estimating the proportions of these classes directly.

Lennington, R. K.↗
NASA NTRS1985

Theoretical Thermodynamics of Mixtures at High Pressures

The development of an understanding of the chemistry of mixtures of metallic hydrogen and abundant, higher-z material such as oxygen, carbon, etc., is important for understanding of fundamental processes of energy release, differentiation, and development of atmospheric abundances in the Jovian planets. It provides a significant theoretical base for the interpretation of atmospheric elemental abundances to be provided by atmospheric entry probes in coming years. Significant differences are found when non-perturbative approaches such as Thomas-Fermi-Dirac (TFD) theory are used. Mapping of the phase diagrams of such binary mixtures in the pressure range from approx. 10 Mbar to approx. 1000 Mbar, using results from three-dimensional TFD calculations is undertaken. Derivation of a general and flexible thermodynamic model for such binary mixtures in the relevant pressure range was facilitated by the following breakthrough: there exists an accurate nd fairly simple thermodynamic representation of a liquid two-component plasma (TCP) in which the Helmholtz free energy is represented as a suitable linear combination of terms dependent only on density and terms which depend only on the ion coupling parameter. It is found that the crystal energies of mixtures of H-He, H-C, and H-O can be satisfactorily reproduced by the same type of model, except that an effective, density-dependent ionic charge must be used in place of the actual total ionic charge.

Hubbard, W. B.↗
NASA NTRS1986

Measurement of viscosity of gaseous mixtures at atmospheric pressure

Coefficients of viscosity of various types of gas mixtures, including simulated natural-gas samples, have been measured at atmospheric pressure and room temperature using a modified capillary tube method. Pressure drops across the straight capillary tube section of a thermal mass flowmeter were measured for small, well-defined, volume flow rates for the test gases and for standard air. In this configuration, the flowmeter provides the volumetric flow rates as well as a well-characterized capillary section for differential pressure measurements across it. The coefficients of viscosity of the test gases were calculated using the reported value of 185.6 micro P for the viscosity of air. The coefficients of viscosity for the test mixtures were also calculated using Wilke's approximation of the Chapman-Enskog (C-E) theory. The experimental and calculated values for binary mixtures are in agreement within the reported accuracy of Wilke's approximation of the C-E theory. However, the agreement for multicomponent mixtures is less satisfactory, possible because of the limitations of Wilkes's approximation of the classical dilute-gas state model.

Singh, J. J.↗
NASA NTRS1986

Lower power dc arcjet operations with hydrogen hydrogen/nitrogen propellant mixtures

The arcjet assembly from a flight model system was modified with a new thoriated tungsten nozzle insert and has been tested with hydrogen-nitrogen mixtures simulating the decomposition products of ammonia and hydrazine. Arcjet power consumption ranged from 0.7 to 1.15 kW depending on low rate, input current, and mixture composition. At a nominal 1 kW power level the ammonia mixtures thrust efficiency was about 0.31 at specific impulse values ranging between 460 and 500 sec. Hydrazine mixtures gave similar thrust efficiencies at the same power level with specific impulse values between 395 and 430 sec. Large, spontaneous voltage mode changes were not observed once the thruster had passed a period of instability immediately following start up. This period of instability, and the startup at low pressure, were seen as major causes of constrictor damage during the tests.

Curran, F. M.↗
NASA NTRS1986

Low power dc arcjet operation with hydrogen/nitrogen propellant mixtures

The arcjet assembly from a flight model system was modified with a new thoriated tungsten nozzle insert and has been tested with hydrogen-nitrogen mixtures simulating the decomposition products of ammonia and hygrazine. Arcjet power consumption ranged from 0.7 to 1.15 kW depending on low rate, input current, and mixture composition. At a nominal 1 kW power level the ammonia mixtures thrust efficiency was about 0.31 at specific impulse values ranging between 460 and 500 sec. Hydrazine mixtures gave similar thrust efficiencies at the same power level with specific impulse values between 395 and 430 sec. Large, spontaneous voltage mode changes were not observed once the thruster had passed a period of instability immediately following start up. This period of instability, and the startup at low pressure, were seen as major causes of constrictor damage during the tests.

Curran, F. M.↗
NASA NTRS1986

Forced convection heat transfer to air/water vapor mixtures

Heat transfer coefficients were measured using both dry air and air/water vapor mixtures in the same forced convection cooling test rig (jet array impingement configurations) with mass ratios of water vapor to air up to 0.23. The primary objective was to verify by direct experiment that selected existing methods for evaluation of viscosity and thermal conductivity of air/water vapor mixtures could be used with confidence to predict heat transfer coefficients for such mixtures using as a basis heat transfer data for dry air only. The property evaluation methods deemed most appropriate require as a basis a measured property value at one mixture composition in addition to the property values for the pure components.

Richards, D. R.↗
NASA NTRS1986

Low power dc arcjet operation with hydrogen/nitrogen/ammonia mixtures

The effect of gas composition and ambient pressure on arcjet operation was determined. Arcjet operation in different facilities was also compared to determine the validity of tests in small facilities. Volt-ampere characteristics were determined for an arcjet using hydrogen/nitrogen mixtures (simulating both ammonia and hydrazine), hydrogen/nitrogen/ammonia mixtures, and pure ammonia as propellants at various flow rates. The arcjet had a typical performance of 450 sec specific impulse at 1 kW with hydrogen/nitrogen mixtures. It was determined that the amount of ammonia present in the gas stream had a significant effect on the arcjet volt-ampere characteristics. Also, hydrogen/nitrogen mixtures simulating ammonia gave arc characteristics approximately the same as those of pure ammonia. Finally, no differences in arc volt-ampere characteristics were seen between low and high ambient pressure operation in the same facility. A 3 to 5 V difference was seen when different facilities were compared, but this difference was probably due to differences in the voltage drops across the current connections, and not due to arcjet operational differences in the two facilities.

Hardy, Terry L.↗
NASA NTRS1988

Interfacial tension and vapor-liquid equilibria in the critical region of mixtures

In the critical region, the concept of two-scale-factor universality can be used to accurately predict the surface tension between near-critical vapor and liquid phases from the singularity in the thermodynamic properties of the bulk fluid. In the present work, this idea is generalized to binary mixtures and is illustrated using the data of Hsu et al. (1985) for CO2 + n-butane. The pressure-temperature-composition-density data for coexisting, near-critical phases of the mixtures are fitted with a thermodynamic potential comprised of a sum of a singular term and nonsingular terms. The nonuniversal amplitudes characterizing the singular term for the mixtures are obtained from the amplitudes for the pure components by interpolation in a space of thermodynamic 'field' variables. The interfacial tensions predicted for the mixtures from the singular term are within 10 percent of the data on three isotherms in the pressure range (Pc - P)/Pc of less than 0.5. This difference is comparable to the combined experimental and model errors.

Moldover, Michael R.↗
NASA NTRS1989

Photo-sensitized ignition of hydrogen/oxygen mixtures for hypersonic flight vehicles

An approach toward improving supersonic ignition and combustion efficiency was investigated under a feasibility program with NASA-Ames. The idea is to selectively irradiate targetted species in the combustion zone. The ensuing photodissociation reactions produce highly reactive radicals which modify the gas phase kinetics. The overall objective of this research was to demonstrate photosensitized ignition of H2/O2 mixtures, and to gain a preliminary understanding of the ignition mechanism, especially as it pertains to the concept of supersonic combustion. To this end, a series of experiments were performed with a model sensitizer, NO2. At subatmospheric pressures and moderate temperatures (above 100 F), mixtures of H2/O2/NO2 are ignitable by a pulsed eximer laser at 308 nm, 115 to 200 mJ. Ignitability was found to be a function of NO2 pressure, temperature, laser energy per pulse, and laser lens focal length (fluence at focal volume). Mixtures could not be ignited in the absence of the sensitizer. While increasing temperature improved sensitized ignition in the lower temperature range, a retarding effect was observed at the highest temperatures. To more thoroughly understand these thermal effects, the UV-Vis and IR spectra of NO2 and H2/O2/NO2 mixtures were studied over the temperature range 70 to 900 F. Initially, increasing temperature shifts the N2O4 in a reversible reaction to 2 NO2 equilibrium toward NO2, favoring photochemical ignition. However, at still higher temperature, NO2 converts to non-absorbing NO + 1/2 O2, thus preventing photosensitized ignition.

Lavid, Moshe↗
NASA NTRS1992

Application of Taguchi methods to dual mixture ratio propulsion system optimization for SSTO vehicles

The application of advanced technologies to future launch vehicle designs would allow the introduction of a rocket-powered, single-stage-to-orbit (SSTO) launch system early in the next century. For a selected SSTO concept, a dual mixture ratio, staged combustion cycle engine that employs a number of innovative technologies was selected as the baseline propulsion system. A series of parametric trade studies are presented to optimize both a dual mixture ratio engine and a single mixture ratio engine of similar design and technology level. The effect of varying lift-off thrust-to-weight ratio, engine mode transition Mach number, mixture ratios, area ratios, and chamber pressure values on overall vehicle weight is examined. The sensitivity of the advanced SSTO vehicle to variations in each of these parameters is presented, taking into account the interaction of each of the parameters with each other. This parametric optimization and sensitivity study employs a Taguchi design method. The Taguchi method is an efficient approach for determining near-optimum design parameters using orthogonal matrices from design of experiments (DOE) theory. Using orthogonal matrices significantly reduces the number of experimental configurations to be studied. The effectiveness and limitations of the Taguchi method for propulsion/vehicle optimization studies as compared to traditional single-variable parametric trade studies is also discussed.

Stanley, Douglas O.↗
NASA NTRS1993

Two and three-dimensional prediffuser combustor studies with air-water mixture

Two- and three-dimensional gas turbine prediffuser-combustor sectors were experimentally studied under a number of mixture and flow conditions in a tunnel operating with a two-phase, air-liquid film-droplet mixture. It is concluded that water vaporization in the combustor causes changes in both local gas temperature and state of vitiation and reduces reaction rates. Substantial accumulation of water and water vapor takes place in pocket over the combustor volume, even when the air-water mixture is steady in time. The accuracy of determining combustor performance changes increases with a better knowledge of the state of the air-water mixture in the primary zone. To establish flame-out conditions it is considered to be necessary to combine the prediction of detailed flowfield and chemical activity with that of flame stability and motion characteristics.

Laing, Peter↗
NASA NTRS1992

Using partially labeled data for normal mixture identification with application to class definition

The problem of estimating the parameters of a normal mixture density when, in addition to the unlabeled samples, sets of partially labeled samples are available is addressed. The density of the multidimensional feature space is modeled with a normal mixture. It is assumed that the set of components of the mixture can be partitioned into several classes and that training samples are available from each class. Since for any training sample the class of origin is known but the exact component of origin within the corresponding class is unknown, the training samples as considered to be partially labeled. The EM iterative equations are derived for estimating the parameters of the normal mixture in the presence of partially labeled samples. These equations can be used to combine the supervised and nonsupervised learning processes.

Shahshahani, Behzad M.↗
NASA NTRS1946

Effect of the NACA Injection Impeller on the Mixture Distribution of a Double-row Radial Aircraft Engine

For the normal range of engine power the impeller provided marked improvement over the standard spray-bar injection system. Mixture distribution at cruising was excellent, maximum cylinder temperatures were reduced about 30 degrees F, and general temperature distribution was improved. The uniform mixture distribution restored the normal response of cylinder temperature to mixture enrichment and it reduced the possibility of carburetor icing, while no serious loss in supercharger pressure rise resulted from injection of fuel near the impeller outlet. The injection impeller also furnished a convenient means of adding water to the charge mixture for internal cooling.

Marble, Frank E.↗