Extracting an Empirical Intermetallic Hydride Design Principle from Limited Data via Interpretable Machine Learning.
Abstract not provided.
Witman, Matthew↗
SEARCH · Engineering Papers
Results for “Intermetallics”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Cascade of Spin-State Transitions in the Intermetallic Marcasite FeP 2
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
Variations in GARS powder microstructure as a function of powder chemistry and particle size
The properties of metal produced through powder metallurgy depends on the feedstock used. Powders produced via gas atomization reaction synthesis (GARS) are used to produce oxide dispersion strengthened alloys. The desired powder size range can vary for each consolidation technique. However, powder microstructure also can vary with powder particle size, which in turn can impact the microstructure and properties of the consolidated parts. In this study, GARS powders are characterized via inductively coupled plasma mass spectroscopy, inert gas fusion, and high-resolution x-ray diffraction to determine variations in elemental and phase compositions. Transmission electron microscopy was used to understand microstructure variations as a function of chemistry and size. Across the three batches tested intermetallic content was 0.73–1.35 wt% in the 0-20 μm powder batch and increased to 2.46–3.80 wt% in the coarse 45-106 μm batch. Across all batches, volume percent of surface oxidation decreased with powder diameter, with volume percents within the range of 0.75–1.2 % across 10 μm powder particles, and below 0.4 % across coarse powder particles approximately 100 μm in diameter. These observations were supported by inert gas fusion measurements. However, the oxide layer was thicker in coarse powder particles due to a slower cooling rate. Increasing oxygen content in atomization gas to 2000 ppm and adding yttrium increased both the surface oxidation content and yttrium intermetallic content. Lastly, intermetallic phases within the powder coarsened with powder size. Intermetallic morphology changed from fine spherical intermetallic and columnar dendritic growth to a cellular structure with finer spherical intermetallic, to coarse irregular intermetallic and intermetallic along grain boundaries as a result of slower cooling rate and solidification rate in coarse powder particles. Furthermore, the addition of zirconium does not appear to significantly change intermetallic morphology, but the composition changed from a Y-Fe rich intermetallic to a Y-Zr-Fe intermetallic.
42 ENGINEERING↗
Elucidating the factors controlling the methanol synthesis from CO 2 on ZnPd-ZnO/TiO 2 catalysts prepared by direct/inverse impregnation
The direct hydrogenation of CO 2 to methanol over supported ZnPd intermetallic catalysts remains a challenge due to the complex nature of the active sites, which are highly dependent on both the dispersion of ZnPd intermetallics and their proximity to ZnO. This study investigates the effect of the Pd and Zn incorporation order on methanol synthesis over TiO 2 -supported ZnPd catalysts. Catalysts were prepared via direct (Pd/Zn), inverse (Zn/Pd), and co-impregnation (Pd+Zn) methods using anatase TiO 2 as the support. Comprehensive characterization by XRD, HRTEM, CO-DRIFTS and XPS revealed that the formation of small and crystalline intermetallic β-ZnPd particles and their interaction with ZnO/ZnO x depends on the sequence of Pd and Zn incorporation. It was found that, under the reaction conditions, the ZnO x species plays a critical role in facilitating the formation of the intermetallic ZnPd through the interactions between Pd and ZnO x . In addition, ZnO x species have also been shown to modulate key catalytic properties, such as CO 2 activation and methanol selectivity. Specifically, the ZnPd/Pd surface ratio, determined by Pd dispersion and proximity to ZnO/ZnO x , was shown to determine the methanol production from CO 2 directly or via a CO intermediate. The Pd/Zn catalyst showed superior selectivity due to the in-situ formation of intermetallic species facilitated by Pd-ZnO x interactions.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Beryllium-driven structural evolution at the divertor surface
Erosion of the beryllium first wall material in tokamak reactors has been shown to result in transport and deposition on the tungsten divertor. Experimental studies of beryllium implantation in tungsten indicate that mixed W–Be intermetallic deposits can form, which have lower melting temperatures than tungsten and can trap tritium at higher rates. To better understand the formation and growth rate of these intermetallics, we performed cumulative molecular dynamics (MD) simulations of both high and low energy beryllium deposition in tungsten. In both cases, a W–Be mixed material layer (MML) emerged at the surface within several nanoseconds, either through energetic implantation or a thermally-activated exchange mechanism, respectively. While some ordering of the material into intermetallics occurred, fully ordered structures did not emerge from the deposition simulations. Targeted MD simulations of the MML to further study the rate of Be diffusion and intermetallic growth rates indicate that for both cases, the gradual re-structuring of the material into an ordered intermetallic layer is beyond accessible MD time scales(≤1 μs). However, the rapid formation of the MML within nanoseconds indicates that beryllium deposition can influence other plasma species interactions at the surface and begin to alter the tungsten material properties. Therefore, beryllium deposition on the divertor surface, even in small amounts, is likely to cause significant changes in plasma-surface interactions and will need to be considered in future studies.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Controlling microstructure and B2 ordering kinetics in Fe–Al system through additive manufacturing
Multi-material fabrication between steel and aluminum is challenging because of the formation of several intermetallic phases. Embrittling B2 ordered intermetallics form in the steel rich side and are stable till about 60% of Al dilution in steel. In this work by using multi-length scale characterization coupled with integrated computational process and thermokinetic modeling, we show that the ordered B2 intermetallics in the steel rich side of the Fe–Al system forms via a nucleation and growth mechanism. The extent of B2 ordered intermetallics can be controlled by modifying the directed energy deposition-additive manufacturing (DED-AM) process parameters. Our findings lay the foundation for enabling fabrication of crack-free functionally graded compositions between the two alloys.
36 MATERIALS SCIENCE↗
Carbide-Modified Pd on ZrO2 as Active Phase for CO2-Reforming of Methane—A Model Phase Boundary Approach
Starting from subsurface Zr0-doped “inverse” Pd and bulk-intermetallic Pd0Zr0 model catalyst precursors, we investigated the dry reforming reaction of methane (DRM) using synchrotron-based near ambient pressure in-situ X-ray photoelectron spectroscopy (NAP-XPS), in-situ X-ray diffraction and catalytic testing in an ultrahigh-vacuum-compatible recirculating batch reactor cell. Both intermetallic precursors develop a Pd0–ZrO2 phase boundary under realistic DRM conditions, whereby the oxidative segregation of ZrO2 from bulk intermetallic PdxZry leads to a highly active composite layer of carbide-modified Pd0 metal nanoparticles in contact with tetragonal ZrO2. This active state exhibits reaction rates exceeding those of a conventional supported Pd–ZrO2 reference catalyst and its high activity is unambiguously linked to the fast conversion of the highly reactive carbidic/dissolved C-species inside Pd0 toward CO at the Pd/ZrO2 phase boundary, which serves the role of providing efficient CO2 activation sites. In contrast, the near-surface intermetallic precursor decomposes toward ZrO2 islands at the surface of a quasi-infinite Pd0 metal bulk. Strongly delayed Pd carbide accumulation and thus carbon resegregation under reaction conditions leads to a much less active interfacial ZrO2–Pd0 state.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Evaluation of high-temperature properties of binary, eutectic Ni-X alloys (X = B, Ca, Ce, La, Y, Zr)
We investigated the high-temperature behavior of binary eutectic nickel-base alloys with low-solubility elements, towards developing alloys with new combinations of structural and functional (e.g. thermal or corrosion) properties. Based on thermodynamic screening, we cast binary near-eutectic Ni-B, Ni-Ca, Ni-Ce, Ni-La, Ni-Y, and Ni-Zr alloys and characterized their microstructure and high-temperature properties. All alloys (except Ni-Ca) contain a fine eutectic microstructure, containing submicron alternating lamellae of γ-Ni and continuous intermetallic phases. The eutectic microstructure did not significantly coarsen at 700°C (except for Ni-B), but measurably coarsened in all alloys at 900°C, most quickly in Ni-B, followed by Ni-Ce, Ni-La, Ni-Y, and Ni-Zr. Coarsening in these alloys occurs by fault migration; diffusion within the intermetallic, and its interfacial energy, likely influence coarsening kinetics. At room-temperature, all alloys possess negligible ductility due to the continuous, brittle intermetallic. At 700 and 900°C, the Ni-Zr alloy showed the best combination of strength and ductility. Oxidation experiments at 900°C on Ni-Zr and Ni-Ce revealed heavy internal oxidation of the continuous intermetallic phase. Overall, the Ni-Zr alloy showed good high-temperature coarsening resistance and strength, though ductility and oxidation resistance require improvement for use in structural applications. Possible routes for improving alloy properties via additive manufacturing are discussed.
Ekaputra, Clement [ORNL] (ORCID:0000000307166479)↗
Thermal Calculations to Determine Maximum Zircaloy Temperatures During Reactor Operations for Campaign 1 Fuel Assemblies
The H-Canyon Facility plans on processing bundles from Non-Aluminum Spent Nuclear Fuel (NASNF) Risk Group 1 (UO 2 core fuels). Uranium-zirconium (UZr) alloys and zirconium clad UO 2 fuel containing UZr intermetallic compound have the potential to cause explosions during dissolution. UZr intermetallic typically only forms when uranium and zirconium (or zirconium alloy) cladding are in contact at high temperatures. Thermal modeling was performed to determine the maximum cladding temperature for Campaign 1 Zircoloy cladded fuel assembles during reactor operation to help determine if the UZr intermetallic compound could have formed during reactor operations. The temperature of 350°C was chosen as a conservative minimum value for the possible formation of intermetallic UZr compound. The modeling approach, inputs, and results are outlined in this document.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Synthesis and magnetic properties of LaFe 13- x - y M x Si y N 3 nitrides
Here, single-phase LaFe 13-x-y M x Si y N 3 compounds (M = Mn) were synthesized by subjecting intermetallic precursors to the ammonia flow at 623 K for 4 h. The nitrides derived from Si-poor (y ≤ 3) cubic intermetallics retain the NaZn 13 -type crystal structure and show considerable (~3 %) lattice expansion compared to the nitrogen-free materials. The temperatures of the magnetic ordering transitions, all of which are second order, increase by ~ 200 K as a result of nitrogenation, and all nitrides exhibit rather weak and broad magnetocaloric effects. The nitrides are stable below 750 K, but they begin to lose nitrogen above this temperature, fully decomposing above 1050 K. The nitrogenation of the tetragonal LaFe 9 Si 4 results in the decomposition of the intermetallic phase and formation of the Fe 3 N compound together with unidentified amorphous phase(s).
36 MATERIALS SCIENCE↗
Fundamental Thermodynamic, Kinetic, and Mechanical Properties of Lithium and Its Alloys
Lithium alloying reactions are beneficial in promoting uniform plating and stripping of lithium metal in all-solid-state batteries. First-principles calculations are performed to predict thermodynamic, kinetic, and mechanical properties of lithium and several important Li–M alloys (M = Mg, Ag, Zn, Al, Ga, In, Sn, Sb, and Bi). While the Li–Mg binary system forms a solid solution, most other lithium–metal alloys prefer stoichiometric intermetallic compounds with common local motifs that enable fast Li diffusion. Lithium and Li-rich alloys exhibit an unusually flat energy landscape along paths that connect BCC to close-packed structures like FCC and HCP, with important implications for mechanical properties. Very low migration barriers for Li diffusion that rival those of superion conductors are predicted, both in pure Li and in Li–M intermetallics. However, vacancy concentration, which is crucial for substitutional diffusion, is predicted to be low in metallic Li and most Li–M intermetallics. Compounds such as B32 LiAl and LiGa as well as D0 3 Li 3 Sb and Li 3 Bi exhibit structural vacancies at higher ends of their voltage windows, which together with low migration barriers leads to exceptionally high Li mobilities. In the Li–Mg solid solution, the addition of Mg is found to decrease the vacancy tracer diffusion coefficient by an order of magnitude.
36 MATERIALS SCIENCE↗
Phase-Controlled Synthesis of Pd–Sn Nanocrystal Catalysts of Defined Size and Shape
Bimetallic Pd-based nanoparticles (NPs) are of interest as electrocatalysts for formic acid electrooxidation (FAEO) because of their higher initial catalytic activity and CO tolerance when compared to Pt. Intermetallic NPs (i-NPs) with specific geometric and electronic structures generally exhibit superior catalytic activity, selectivity, and durability when compared to their disordered (random alloy) counterparts; however, the colloidal synthesis of i-NPs remains a challenge. Here, a one-pot method was demonstrated as a facile route to obtain monodisperse Pd–Sn NPs with phase control, including intermetallic hexagonal Pd 3 Sn 2 (P6 3 /mmc), intermetallic orthorhombic Pd 2 Sn (Pnma), and alloy cubic Pd 3 Sn (FCC, Fm 3 ¯m) as size-controlled NPs with quasi-spherical shapes. Initial metal precursor ratios and reaction temperature were critical parameters to achieving phase control. Also, slight modifications of synthetic conditions resulted in either Pd 2 Sn nanorhombohedra or nanorods with tunable aspect ratios. A systematic evaluation of the Pd–Sn NPs for FAEO showed that most presented higher specific activities when compared to commercial Pd/C, in which Pd 2 Sn quasi-spheres and nanorhombohedra showed the highest catalytic activity for FAEO. Furthermore, these results highlight the benefits of phase-controlled Pd-based nanocatalysts with defined nanocrystal size and shape, with use of trioctylphospine (TOP) and oleic acid (OA) central to shape and size control.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Computational Design of Interlayers for Thermally Stable Compositionally Graded Coatings on Nickel Alloys
To extend the service life of Ni-based superalloys, refractory metal coatings are often used. However, direct bonding between metals with dissimilar crystal structure promotes brittle intermetallic phase formation. This work presents a computational thermodynamic framework for high throughput design of functionally graded interlayers to suppress deleterious phases that may form at the interlayer. The Thermo-Calc software package was used to screen candidate metallic interlayer elements based on stability of solid-solution phases. Vanadium was identified as a promising interlayer due to its consistent suppression of intermetallic phases. Temperature-dependent phase diagram mapping between 600 and 1000 °C guided selection of a compositional pathway that significantly reduced intermetallic formation compared to directly joining the Ni-based and Nb refractory alloys. Time–temperature–transformation analysis was performed to assess whether equilibrium-predicted phases are kinetically accessible along regions of the graded path where non-solid-solution phases are not fully suppressed. The methodology was further applied to additional Ni-based alloy and coating systems, illustrating its transferability as an approach for rapid computational design of graded interlayers in dissimilar high-temperature materials.
36 MATERIALS SCIENCE↗
Phase equilibria and microstructure evolution in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C
The equilibrium compositions of all phases in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C were determined experimentally through isothermal annealing for up to 500 h and compared with currently available computational thermodynamic descriptions. Additionally, the study examined how adding a third element to the binary system affects the microstructure by analyzing changes in the volume fraction of the intermetallic phase in the eutectic region. It was observed that Nb and Ti addition lowered the intermetallic fraction in the eutectic region while Al and Cr addition did the opposite. The fraction of intermetallic phase in the eutectic region is very important because it contributes to extreme brittleness of these alloys. Also, Al, Nb and Ti addition promoted different precipitates upon annealing when added in sufficient amounts. The collected data on composition and phase equilibria provides crucial information for improving the thermodynamic assessments of the binary and ternary alloy systems.
energy dispersive spectrometry↗
Al-Cu-Ce(-Zr) alloys with an exceptional combination of additive processability and mechanical prope
Explore the source record for details and available documents.
Bahl, Sumit↗
Phase stability and magnetic and electronic properties of a spark plasma sintered CoFe – P soft magnetic alloy
More efficient power conversion devices are able to transmit greater electrical power across larger distances to satisfy growing global electrical needs. A critical requirement to achieve more efficient power conversion are the soft magnetic materials used as core materials in transformers, inductors, and motors. To that effect it is well known that the use of non-equilibrium microstructures, which are, for example, nanocrystalline or consist of single phase solid solutions, can yield high saturation magnetic polarization and high electrical resistivity necessary for more efficient soft magnetic materials. In this work, we synthesized CoFe – P soft magnetic alloys containing nanocrystalline, single phase solid solution microstructures and studied the effect of a secondary intermetallic phase on the saturation magnetic polarization and electrical resistivity of the consolidated alloy. Single phase solid solution CoFe – P alloys were prepared through mechanically alloying metal powders and phase decomposition was observed after subsequent consolidation via spark plasma sintering (SPS) at various temperatures. The secondary intermetallic phase was identified as the orthorhombic (Co x Fe 1-x ) 2 P phase and the magnetic properties of the (Co x Fe 1-x ) 2 P intermetallic phase were found to be detrimental to the soft magnetic properties of the targeted CoFe – P alloy.
36 MATERIALS SCIENCE↗
Wire directed energy deposition of steel-aluminum structures using cold metal transfer process
In this study, a sharp transition from 316L stainless steel to 4043 aluminum alloy was fabricated using wire directed energy deposition (DED) via the cold metal transfer (CMT) process. The CMT process with its inherently low heat input, led to a significant reduction in intermetallic thickness at the bi-metallic interface compared to blown powder DED technique reported in the literature resulting in superior properties when compared to those of dissimilar steel-aluminum welds. Thermo-kinetic modeling confirmed that the intermetallic formation is through a classical nucleation and growth mechanism, and the fraction and thickness can be controlled by adjusting CMT process parameters to kinetically arrest or minimize the intermetallic formation. These findings underscore the efficacy of CMT-based wire DED for fabrication of steel-aluminum bi-metallic structures.
36 MATERIALS SCIENCE↗
Developing an experimental-computational framework to investigate the deformation mechanisms and mechanical properties of Al-8Ce-10Mg alloys at micro and macroscales
There is a promising future for the use of aluminum-cerium-magnesium alloys in a broad range of applications, including devices that operate at high temperatures. With cerium currently considered a waste product of rare earth mining validation studies of possible applications are essential to reduce the environmental waste. Here, a computational-experimental framework is developed to investigate the role both the intermetallic and matrix have on the mechanical properties of these alloys. A set of experiments, including SEM/EBSD imaging, nanoindentation, in-situ SEM tensile testing, and in-situ SEM-DIC tests are performed to characterize the microstructure and mechanical properties of these alloys. Furthermore, the elastic, plastic, and failure deformation mechanisms of the microstructure, and their correlation with the bulk scale mechanical properties are investigated. Experimental results are also used to calibrate parameters for a crystal plasticity finite element model, by performing a computational framework that minimizes the error between the computational and experimental results. This model is then utilized to investigate how the area percentage of intermetallics and the crystallographic texture control the mechanical properties of the alloy. Simulation results show that an increase in the percentage of intermetallics increase the strength but decrease the ductility of the alloy. Also, a change in material texture improves strength and reduces damage that leads to material failure. The development of the crystal plasticity model, as discussed in this work, opens opportunities for future investigations of similar aluminum-cerium-magnesium alloys.
36 MATERIALS SCIENCE↗