Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Inconel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Effects of Heat Treatment on the Ballistic Impact Properties of Inconel 718 for Jet Engine Fan Containment Applications

The effects of heat treating Inconel 718 on the ballistic impact response and failure mechanisms were studied. Two different annealing conditions and an aged condition were considered. Large differences in the static properties were found between the annealed and the aged material, with the annealed condition having lower strength and hardness and greater elongation than the aged. High strain rate tests show similar results. Correspondingly large differences were found in the velocity required to penetrate material in the two conditions in impact tests involving 12.5 mm diameter, 25.4 mm long cylindrical Ti-6-4 projectiles impacting flat plates at velocities in the range of 150 to 300 m/sec. The annealed material was able to absorb over 25 percent more energy than the aged. This is contrary to results observed for ballistic impact response for higher velocity impacts typically encountered in military applications where it has been shown that there exists a correlation between target hardness and ballistic impact strength. Metallographic examination of impacted plates showed strong indication of failure due to adiabatic shear. In both materials localized bands of large shear deformation were apparent, and microhardness measurements indicated an increase in hardness in these bands compared to the surrounding material. These bands were more localized in the aged material than in the annealed material. In addition the annealed material underwent significantly greater overall deformation before failure. The results indicate that lower elongation and reduced strain hardening behavior lead to a transition from shear to adiabatic shear failure, while high elongation and better strain hardening capabilities reduce the tendency for shear to localize and result in an unstable adiabatic shear failure. This supports empirical containment design methods that relate containment thickness to the static toughness.

Pereira, J. Michael↗
NASA NTRS2001

Effects of Heat Treatment on the Ballistic Impact Properties of Inconel 718 for Jet Engine Fan Containment Applications

The effects of heat treating Inconel 718 on the ballistic impact response and failure mechanisms were studied. Two different annealing conditions and an aged condition were considered. Large differences in the static properties were found between the annealed and the aged material, with the annealed condition having lower strength and hardness and greater elongation than the aged. High strain rate tests show similar results. Correspondingly large differences were found in the velocity required to penetrate material in the two conditions in impact tests involving 12.5 mm diameter, 25.4 mm long cylindrical Ti-6-4 projectiles impacting flat plates at velocities in the range of 150 to 300 m/sec. The annealed material was able to absorb over 25 percent more energy than the aged. This is contrary to results observed for ballistic impact response for higher velocity impacts typically encountered in military applications where it has been shown that there exists a correlation between target hardness and ballistic impact strength. Metallographic examination of impacted plates showed strong indication of failure due to adiabatic shear. In both materials localized bands of large shear deformation were apparent, and microhardness measurements indicated an increase in hardness in these bands compared to the surrounding material. These bands were more localized in the aged material than in the annealed material. In addition the annealed material underwent significantly greater overall deformation before failure. The results indicate that lower elongation and reduced strain hardening behavior lead to a transition from shear to adiabatic shear failure, while high elongation and better strain hardening capabilities reduce the tendency for shear to localize and result in an unstable adiabatic shear failure. This supports empirical containment design methods that relate containment thickness to the static toughness.

Pereira, J. Michael↗
NASA NTRS2002

Hydrostatic Stress Effect On the Yield Behavior of Inconel 100

Classical metal plasticity theory assumes that hydrostatic stress has no effect on the yield and postyield behavior of metals. Recent reexaminations of classical theory have revealed a significant effect of hydrostatic stress on the yield behavior of notched geometries. New experiments and nonlinear finite element analyses (FEA) of Inconel 100 (IN 100) equal-arm bend and double-edge notch tension (DENT) test specimens have revealed the effect of internal hydrostatic tensile stresses on yielding. Nonlinear FEA using the von Mises (yielding is independent of hydrostatic stress) and the Drucker-Prager (yielding is linearly dependent on hydrostatic stress) yield functions was performed. In all test cases, the von Mises constitutive model, which is independent of hydrostatic pressure, overestimated the load for a given displacement or strain. Considering the failure displacements or strains, the Drucker-Prager FEMs predicted loads that were 3% to 5% lower than the von Mises values. For the failure loads, the Drucker Prager FEMs predicted strains that were 20% to 35% greater than the von Mises values. The Drucker-Prager yield function seems to more accurately predict the overall specimen response of geometries with significant internal hydrostatic stress influence.

Allen, Phillip A.↗
NASA NTRS2003

Hydrostatic Stress Effect on the Yield Behavior of Inconel 100

Classical metal plasticity theory assumes that hydrostatic stress has negligible effect on the yield and postyield behavior of metals. Recent reexaminations of classical theory have revealed a significant effect of hydrostatic stress on the yield behavior of various geometries. Fatigue tests and nonlinear finite element analyses (FEA) of Inconel 100 (IN100) equal-arm bend specimens and new monotonic tests and nonlinear finite element analyses of IN100 smooth tension, smooth compression, and double-edge notch tension (DENT) test specimens have revealed the effect of internal hydrostatic tensile stresses on yielding. Nonlinear FEA using the von Mises (yielding is independent of hydrostatic stress) and the Drucker-Prager (yielding is linearly dependent on hydrostatic stress) yield functions were performed. A new FEA constitutive model was developed that incorporates a pressure-dependent yield function with combined multilinear kinematic and multilinear isotropic hardening using the ABAQUS user subroutine (UMAT) utility. In all monotonic tensile test cases, the von Mises constitutive model, overestimated the load for a given displacement or strain. Considering the failure displacements or strains for the DENT specimen, the Drucker-Prager FEM s predicted loads that were approximately 3% lower than the von Mises values. For the failure loads, the Drucker Prager FEM s predicted strains that were up to 35% greater than the von Mises values. Both the Drucker-Prager model and the von Mises model performed equally-well in simulating the equal-arm bend fatigue test.

Allen, Phillip A.↗
NASA NTRS2000

Effects of Various Heat Treatments on the Ballistic Impact Properties of Inconel 718 Investigated

Uncontained failures of aircraft engine fan blades are serious events that can cause equipment damage and loss of life. Federal Aviation Administration (FAA) certification requires that all engines demonstrate the ability to contain a released fan blade with the engine running at full power. However, increased protection generally comes at the expense of weight. Proper choice of materials is therefore imperative to an optimized design. The process of choosing a good casing material is done primarily through trial and error. This costly procedure could be minimized if there was a better understanding of the relationships among static material properties, impact properties, and failure mechanisms. This work is part of a program being conducted at the NASA Glenn Research Center at Lewis Field to study these relationships. Ballistic impact tests were conducted on flat, square sheets of Inconel 718 that had been subjected to different heat treatments. Two heat treatments and the as-received condition were studied. In addition, results were compared with those from an earlier study involving a fourth heat treatment. The heat treatments were selected on the basis of their effects on the static tensile properties of the material. The impact specimens used in this study were 17.8-cm square panels that were centered and clamped over a 15.2-cm square hole in a 1.27-cm-thick steel plate. Three nominal plate thickness dimensions were studied, 1.0, 1.8, and 2.0 mm. For each thickness, all the specimens were taken from the same sheet of material. The projectile was a Ti-6Al-4V cylinder with a length of 25.4 mm, a diameter of 12.7 mm, and a mass ranging from 14.05 to 14.20 g. The projectiles were accelerated toward the specimens at normal incidence using a gas gun with a 2-m-long, 12.7-mm inner-diameter barrel. The ballistic limit for each heat treatment condition and thickness was determined by conducting a number of impact tests that bracketed as closely as possible the velocity required to penetrate the specimen.

Pereira, J. Michael↗
NASA NTRS2002

Long-Term Creep of a Thin-Walled Inconel 718 Stirling Power-Convertor Heater Head Assessed

The Department of Energy and NASA have identified Stirling power convertors as candidate power supply systems for long-duration, deep-space science missions. A key element for qualifying the flight hardware is a long-term durability assessment for critical hot section components of the power convertor. One such critical component is the power convertor heater head. The heater head is a high-temperature pressure vessel that transfers heat to the working gas medium of the convertor, which is typically helium. An efficient heater head design is the result of balancing the divergent requirements of thin walls for increased heat transfer versus thick walls to lower the wall stresses and thus improve creep resistance and durability. In the current design, the heater head is fabricated from the Ni-base superalloy Inconel 718 (IN 718, Inco Alloys International, Inc., Huntington, WV). Although IN 718 is a mature alloy system (patented in 1962), there is little long-term (>50,000-hr) creep data available for thin-specimen geometries. Since thin-section properties tend to be inferior to thicker samples, it is necessary to generate creep data using specimens with the same geometry as the actual flight hardware. Therefore, one facet of the overall durability assessment program involves generating relatively short-term creep data using thin specimens at the design temperature of 649 C (1200 F).

Bowman, Randy R.↗
NASA NTRS2005

Fatigue Crack Growth Rate of Inconel 718 Sheet at Cryogenic Temperatures

Inconel 718 sheet material was tested to determine fatigue crack growth rate (FCGR) at cryogenic conditions representative of a liquid hydrogen (LH2) environment at -423 degree F. Tests utilized M(T) and ESE(T) specimen geometries and environments were either cold gaseous helium or submersion in LH2. The test results support a significant improvement in the fatigue crack growth threshold at -423 degree F compared to -320 degree F or 70 degree F.

Wells, Douglas↗
NASA NTRS2006

Diffusion of Hydrogen and Helium in Inconel 625

Diffusion parameters for hydrogen and helium in Inconel 625 were investigated. The dependence of permeability of hydrogen in the temperature range 310 - 750 C is given. Solubility of hydrogen at 1 atm in the range 640 - 860 C was determined and diffusivity of the gas was calculated. Experiments with diffusion and solubility at 0.09 atm suggest a molecular mechanism of solution of hydrogen in the material. Diffusivity of helium was estimated at less than 10(exp -18) sq cm/s (at 1040 C).

Palosz, W.↗
NASA NTRS2007

Study of Radiographic Linear Indications and Subsequent Microstructural Features in Gas Tungsten Arc Welds of Inconel 718

This study presents examples and considerations for differentiating linear radiographic indications produced by gas tungsten arc welds in a 0.05-in-thick sheet of Inconel 718. A series of welds with different structural features, including the enigma indications and other defect indications such as lack of fusion and penetration, were produced, radiographed, and examined metallographically. The enigma indications were produced by a large columnar grain running along the center of the weld nugget occurring when the weld speed was reduced sufficiently below nominal. Examples of respective indications, including the effect of changing the x-ray source location, are presented as an aid to differentiation. Enigma, nominal, and hot-weld specimens were tensile tested to demonstrate the harmlessness of the enigma indication. Statistical analysis showed that there is no difference between the strengths of these three weld conditions.

Walley, J. L.↗
NASA NTRS2008

Reactivity Studies of Inconel 625 with Sodium, and Lunar Regolith Stimulant

In the event of the need for nuclear power in exploration, high flux heat pipes will be needed for heat transfer from space nuclear reactors to various energy conversion devices, and to safely dissipate excess heat. Successful habitation will necessitate continuous operation of alkali metal filled heat pipes for 10 or-more years in a hostile environment with little maintenance. They must be chemical and creep resistant in the high vacuum of space (lunar), and they must operate reliably in low gravity conditions with intermittent high radiation fluxes. One candidate material for the heat pipe shell, namely Inconel 625, has been tested to determine its compatibility with liquid sodium. Any reactivity could manifest itself as a problem over the long time periods anticipated. In addition, possible reactions with the lunar regolith will take place, as will evaporation of selected elements at the external surfaces of the heat pipes, and so there is a need for extensive long-term testing under simulated lunar conditions.

Gillies, Donald↗
NASA NTRS2014

Neutron Imaging for Selective Laser Melting Inconel Hardware with Internal Passages

Additive Manufacturing is showing great promise for the development of new innovative designs and large potential life cycle cost reduction for the Aerospace Industry. However, more development work is required to move this technology into space flight hardware production. With selective laser melting (SLM), hardware that once consisted of multiple, carefully machined and inspected pieces, joined together can be made in one part. However standard inspection techniques cannot be used to verify that the internal passages are within dimensional tolerances or surface finish requirements. NASA/MSFC traveled to Oak Ridge National Lab's (ORNL) Spallation Neutron Source to perform some non-destructive, proof of concept imaging measurements to assess the capabilities to understand internal dimensional tolerances and internal passages surface roughness. This presentation will describe 1) the goals of this proof of concept testing, 2) the lessons learned when designing and building these Inconel 718 test specimens to minimize beam time, 3) the neutron imaging test setup and test procedure to get the images, 4) the initial results in images, volume and a video, 4) the assessment of using this imaging technique to gather real data for designing internal flow passages in SLM manufacturing aerospace hardware, and lastly 5) how proper cleaning of the internal passages is critically important. In summary, the initial results are very promising and continued development of a technique to assist in SLM development for aerospace components is desired by both NASA and ORNL. A plan forward that benefits both ORNL and NASA will also be presented, based on the promising initial results. The initial images and volume reconstruction showed that clean, clear images of the internal passages geometry are obtainable. These clear images of the internal passages of simple geometries will be compared to the build model to determine any differences. One surprising result was that a new cleaning process was used on these simply geometric specimens that resulted in what appears to be very smooth internal surfaces, when compared to other aerospace hardware cleaning methods.

Tramel, Terri L.↗
NASA NTRS2014

Texture-Induced Anisotropy in an Inconel 718 Alloy Deposited Using Electron Beam Freeform Fabrication

A test block of Inconel (IN) 718 was fabricated using electron beam freeform fabrication (EBF(sup 3)) to examine how the EBF(sup 3) deposition process affects the microstructure, crystallographic texture, and mechanical properties of IN 718. Tests revealed significant anisotropy in the elastic modulus for the as-deposited IN 718. Subsequent tests were conducted on specimens subjected to a heat treatment designed to decrease the level of anisotropy. Electron backscatter diffraction (EBSD) was used to characterize crystallographic texture in the as-deposited and heat treated conditions. The anisotropy in the as-deposited condition was strongly affected by texture as evidenced by its dependence on orientation relative to the deposition direction. Heat treatment resulted in a significant improvement in modulus of the EBF(sup 3) product to a level nearly equivalent to that for wrought IN 718 with reduced anisotropy; reduction in texture through recrystallization; and production of a more homogeneous microstructure.

Tayon, W.↗
NASA NTRS2018

Inertial Weldment of Rhenium and Inconel 718

Inertia welding has been found to be a successful method for joining pure rhenium to Inconel 718, and with additional experimentation, this process may have great potential for rocket nozzle applications. Refractory metals are ideally suited to this application, where high temperatures and oxidizing environment survivability is required, but not all of the thruster must be made of these materials, only the areas that require them. A bolted joint between the two metals is not ideal, especially for small thrusters where the mess of a bolted join will come at a steep price. A welded joint would be preferred for flight thrusters.

Cavender, D. P.↗
NASA NTRS2019

Fabrication and Performance of NiCuCoFeMn High Entropy Alloy Nanopastes for Brazing Inconel 718

Overview: High entropy alloys (HEAs) are a class of metallic alloys consisting of 5 plus elemental components and have four core effects - 1. High mixing entropy - 2. Sluggish diffusion kinetics - 3. High lattice distortion - 4. Cocktail effect; Boron-free, silicon-free brazing materials for nickel superalloys to avoid brittle intermetallic and eutectic phase formation; Size-dependent melting point depression can eliminate the need for boron, silicon and other melting point depressants; A Ni-Mn-Fe-Co-Cu HEA with low solidus and liquidus temperatures (1080 °C and 1150 °C) was developed; Low solidus and liquidus temperatures of the HEA combined with the nanoscale melting point depression in this study; Bulk HEA fabricated by induction melting of elemental powders; HEA nanoparticles (NPs) fabricated by ball milling of the HEA micropowder; Inconel 718 was laser brazed in air using the HEA and bulk and NP performances are compared.

Bridges, Denzel↗
NASA NTRS2019

Additive Manufacturing Development and Hot-Fire Testing of Liquid Rocket Channel Wall Nozzles Using Blown Powder Directed Energy Deposition Inconel 625 and JBK-75 Alloys

Additive manufacturing (AM) is being investigated at NASA and across much of the rocket propulsion industry as an alternate fabrication technique to create complex geometries for liquid engine components that offers schedule and cost saving opportunities. The geometries that can be created using AM offer a significant advantage over traditional techniques. Internal complexities, such as internal coolant channels for combustion chambers and nozzles that would typically require several operations to manufacture traditionally can be fabricated in one process. Additionally, the coolant channels are closed out as a part of the AM build process, eliminating the complexities of a traditional process like brazing or plating. The primary additive manufacturing technique that has been evaluated is powder bed fusion (PBF), or selective laser melting (SLM), but there is a scale limitation for this technique. There are several alternate additive manufacturing techniques that are being investigated for large-scale nozzles and chambers including directed energy deposition (DED) processes. A significant advantage of the DED processes is the ability to adapt to a robotic or gantry CNC system with a localized purge or purge chamber, allowing unlimited build volume. This paper will discuss the development and hot-fire testing of channel-cooled nozzles fabricated utilizing one form of DED called blown powder deposition. This initial development work using blown powder DED is being explored to form the entire channel wall nozzle with integral coolant channels within a single AM build. Much of this development is focused on the design and DED-fabrication of complex and thin-walled features and on characterization of the materials properties produced with this techniques in order to evolve this process. Subscale nozzles were fabricated using this DED technique and hot-fire tested in Liquid Oxygen/Hydrogen (LOX/GH2) and LOX/Kerosene (LOX/RP-1) environments accumulating significant development time and cycles. The initial materials that were evaluated during this testing were high-strength nickel-based Inconel 625 and JBK-75. Further process development is being completed to increase the scale of this technology for large-scale nozzles. This paper will summarize the general design considerations for DED, specific channel-cooled nozzle design, manufacturing process development, property development, initial hot-fire testing and future developments to mature this technology for regeneratively-cooled nozzles. An overview of future development at NASA will also be discussed.

Gradl, Paul R.↗
NASA NTRS2019

Additive Manufacturing and Hot-Fire Testing of Bimetallic GRCop-84 and C-18150 Channel-Cooled Combustion Chambers Using Powder Bed Fusion and Inconel 625 Hybrid Directed Energy Deposition

Additive manufacturing (AM) is an advanced fabrication technique that is demonstrating tremendous potential to reduce fabrication lead times and costs for liquid rocket engine components. The additive manufacturing technology lends itself to fabricate components with complex features such as internal coolant channels in combustion chambers that would otherwise require complex manufacturing operations. A requirement for high performance engines is to use high conductivity, high strength materials such as copper-alloys for combustion chamber liners to provide adequate wall temperatures and meet subsequent structural margins. A further requirement of this configuration is to minimize weight by defining and fabricating material in discrete locations as required. NASA and Industry partner, Virgin Orbit, have been working to advance these technologies through development of bimetallic additive manufacturing techniques under a public-private partnership through NASA’s Announcement of Collaborative Opportunity (ACO). This partnership is advancing a bimetallic hybrid additively manufactured combustion chamber that integrates Powder Bed Fusion (PBF), specifically Selective Laser Melting (SLM), and Directed Energy Deposition (DED) blown powder techniques to optimize the chamber materials and subsequent assembly. The SLM process is being developed for the combustion chamber liner to use copper-alloys GRCop-84 (Copper-Chrome-Niobium) or C-18150 (Copper-Chrome-Zirconium). The hybrid DED blown powder technology is used to apply an integrated structural jacket and manifolds using an Inconel 625 superalloy on the outer surface of the SLM copper liner. The hybrid DED technology being used on this program is a DMG Mori Seiki AM machining center which integrates the DED blown powder with an integral subtractive (traditional) machining to minimize overall setups. A series of chambers were fabricated using these techniques with GRCop-84/Inconel 625 and C-18150/Inconel and hot-fire tested at NASA Marshall Space Flight Center (MSFC) in LOX/Kerosene (RP-1). This paper describes the process development to integrate these AM technologies into an integrated bimetallic assembly, the design of the chamber, results from hot-fire testing, and further development.

Gradl, Paul R.↗
NASA NTRS2019

Additive Manufacturing and Hot-fire Testing of Bimetallic GRCop-84 and C-18150 Channel-Cooled Combustion Chambers using Powder Bed Fusion and Inconel 625 Hybrid Directed Energy Deposition

Additive manufacturing (AM) is an advanced fabrication technique that is demonstrating tremendous potential to reduce fabrication lead times and costs for liquid rocket engine components. The additive manufacturing technology lends itself to fabricate components with complex features such as internal coolant channels in combustion chambers that would otherwise require complex manufacturing operations. A requirement for high performance engines is to use high conductivity, high strength materials such as copper-alloys for combustion chamber liners to provide adequate wall temperatures and meet subsequent structural margins. A further requirement of this configuration is to minimize weight by defining and fabricating material in discrete locations as required. NASA and Industry partner, Virgin Orbit, have been working to advance these technologies through development of bimetallic additive manufacturing techniques under a public-private partnership through NASA’s Announcement of Collaborative Opportunity (ACO). This partnership is advancing a bimetallic hybrid additively manufactured combustion chamber that integrates Powder Bed Fusion (PBF), specifically Selective Laser Melting (SLM), and Directed Energy Deposition (DED) blown powder techniques to optimize the chamber materials and subsequent assembly. The SLM process is being developed for the combustion chamber liner to use copper-alloys GRCop-84 (Copper-Chrome-Niobium) or C-18150 (Copper-Chrome-Zirconium). The hybrid DED blown powder technology is used to apply an integrated structural jacket and manifolds using an Inconel 625 superalloy on the outer surface of the SLM copper liner. The hybrid DED technology being used on this program is a DMG Mori Seiki AM machining center which integrates the DED blown powder with an integral subtractive (traditional) machining to minimize overall setups. A series of chambers were fabricated using these techniques with GRCop-84/Inconel 625 and C-18150/Inconel and hot-fire tested at NASA Marshall Space Flight Center (MSFC) in LOX/Kerosene (RP-1). This paper describes the process development to integrate these AM technologies into an integrated bimetallic assembly, the design of the chamber, results from hot-fire testing, and further development.

Gradl, Paul↗
NASA NTRS2020

Impact Testing of Inconel 718 for Material Impact Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain-rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition, there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data, and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration (FAA) William J. Hughes Technical Center. Unique features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all of the raw data is available. Four parallel efforts are currently underway. The Ohio State University conducts both measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles. The George Mason University conducts the development of improved numerical modeling techniques for deformation and failure. Glenn conducts the impact testing of flat panels and substructures. This report describes impact testing performed on Inconel 718 sheet and plate samples of different thicknesses with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

J Michael Pereira↗