SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flow fields in two- and three-dimensional axisymmetric supersonic inlets are calculated with computer program that uses method of characteristics to compute array of points in flow field. At each point, local pressure, local Mach number, local flow angle, and static pressure are calculated. Program can be used to design and analyze supersonic inlets by determining surface compression rates and throat flow properties.
A flow-through inlet test program was conducted to evaluate inlet test methods and determine the impact of the fan on inlet separation when operating at large angles of attack. A total of 16 model configurations of approximately 1/6 scale were tested. A comparison of these flow-through results with powered data indicates the presence of the fan increased separation operation 3 degrees to 4 degrees over the flow through inlet. Rods and screens located at the fan face station, that redistribute the flow, achieved simulation of the powered-fan results for separation angle of attack. Concepts to reduce inlet distortion and increase angle of attack capability were also evaluated. Vortex generators located on the inlet surface increased inlet angle of attack capability up to 2 degrees and reduced inlet distortion in the separated region. Finally, a method of simulating the fan/inlet aerodynamic interaction using blockage sizing method has been defined. With this method, a static blockage device used with a flow-through model will approximate the same inlet onset of separation angle of attack and distortion pattern that would be obtained with an inlet model containing a powered fan.
A numerical method originally developed for three-dimensional supersonic inlet flow calculations is extended and applied to the study of two-dimensional and three-dimensional flows associated with arbitrary propulsion systems. The method is based on the forward spatial marching solution of a reduced form of the three-dimensional steady Navier-Stokes equations in which streamwise pressure gradients are retained in both the subsonic and supersonic regions. The present paper briefly describes the analysis and then shows three applications. In the first application, a wall transpiration study has been performed for the two-dimensional shock wave/turbulent boundary layer interaction flow field with application to an inlet configuration. The second application treats a rectangular high speed inlet with a swept sideplate including the effects of sideplate spillage. Finally, the method is utilized to analyze the interaction of an under-expanded supersonic jet with an ambient flow. Computed results are examined and compared with available experimental measurements. It is demonstrated that the present numerical method is capable of numerically simulating complex two- and three-dimensional flows relevant to hypersonic propulsion systems in a manner which both shows good agreement with data when such data is available, and which shows the complex flow features in the absence of data.
Explore the source record for details and available documents.
Computations have been performed on a three-dimensional inlet associated with the NASA Ames combustor model for the hypersonic propulsion experiment in the 16-inch shock tunnel. The 3-dimensional inlet was designed to have the combustor inlet flow nearly two-dimensional and of sufficient mass flow necessary for combustion. The 16-inch shock tunnel experiment is a short duration test with test time of the order of milliseconds. The flow through the inlet is in chemical non-equilibrium. Two test entries have been completed and limited experimental results for the inlet region of the combustor-model are available. A number of CFD simulations, with various levels of simplifications such as 2-D simulations, 3-D simulations with and without chemical reactions, simulations with and without turbulent conditions, etc., have been performed. These simulations have helped determine the model inlet flow characteristics and the important factors that affect the combustor inlet flow and the sensitivity of the flow field to these simplifications. In the proposed paper, CFD modeling of the hypersonic inlet, results from the simulations and comparison with available experimental results will be presented.
Flows calculated for realistic engine-inlet conditions. Computer code LAPIN, large-perturbation inlet, developed to analyze large-perturbation, transient-flow fields in supersonic inlets. Robust, quick-running code capable of solving unsteady quasi-one-dimensional, inviscid-flow problems in mixed subsonic and supersonic regimes for inlets. Approach based upon quasi-one-dimensional, inviscid, unsteady formulation including engineering models of unstart/restart, bleed, bypass, and geometrical effects. Numerical solution of governing time-dependent equations of motion accomplished through shock-capturing, finite-difference algorithm. Program written in FORTRAN IV.
A flow energy harvesting device having a harvester pipe includes a flow inlet that receives flow from a primary pipe, a flow outlet that returns the flow into the primary pipe, and a flow diverter within the harvester pipe having an inlet section coupled to the flow inlet, a flow constriction section coupled to the inlet section and positioned at a midpoint of the harvester pipe and having a spline shape with a substantially reduced flow opening size at a constriction point along the spline shape, and an outlet section coupled to the constriction section. The harvester pipe may further include a piezoelectric structure extending from the inlet section through the constriction section and point such that the fluid flow past the constriction point results in oscillatory pressure amplitude inducing vibrations in the piezoelectric structure sufficient to cause a direct piezoelectric effect and to generate electrical power for harvesting.
Top inlet flow field and inlet performance data are presented which provide preliminary insight into the feasibility of upper-fuselage mounted inlet systems for transonic-supersonic fighter aircraft. Presented data span the Mach 0.2 to 2.0 envelope and enable evaluation of the influence of key aircraft configuration variables - inlet location, wing position, wing leading-edge extension (LEX) planform area, and variable incidence canards - on top inlet performance. The viability of this concept relative to more conventional inlet/airframe integrations is assessed via comparative evaluation of top and conventional inlet flow field parameters at transonic and supersonic speeds. It is shown that the action of the wing LEX vortex system produces a significant improvement in top inlet performance. Currently available transonic-supersonic data indicate that top inlet systems pose a viable configuration option for fighter aircraft requiring moderate angle of attack capability. However, recently acquired data indicate that increased angle of attack capability may be obtained by increasing wing leading-edge sweep angle.
A single rotating blade row was tested with two magnitudes of tip radial distortion and two magnitudes of hub radial distortion imposed on the inlet flow. The rotor was about 50 centimeters (20 in.) in diameter and had a design operating tip speed of approximately 420 meters per second (1380 ft/sec). Overall performance at 60, 80, and 100 percent of equivalent design speed generally showed a decrease (compared to undistorted flow) in rotor stall margin with tip radial distortion but no change, or a slight increase, in rotor stall margin with hub radial distortion. At design speed there was a decrease in rotor overall total pressure ratio and choke flow with all inlet flow distortions. Radial distributions of blade element parameters are presented for selected operating conditions at design speed.
The effects of inlet-air-flow distortions on the performance of the J65-B-3 turbojet engine were determined over a range of altitudes from 15,000 to 50,000 feet at a flight Mach number of 0.8. Radial inlet-air-flow distortions apparently do not affect the radial distribution of pressure after the first few compressor stages, while the circumferential inlet-air-flow distortion carried completely through the engine. For the distortions investigated, at rated exhaust-gas temperature and fixed-area exhaust-nozzle operation, the primary effect of the radial inlet-air-flow distortions was to reduce the engine air flow, and the primary effect of the circumferential distortion was to impose a temperature profile on the turbine, both resulting in reduction of thrust.
Stage B, composed of tandem-airfoil rotor B and stator B, was tested with uniform inlet flow and with hub radial, tip radial and 90 degree one-per-revolution circumferential distortion of the inlet flow as part of an overall program to evaluate the effectiveness of tandem airfoils for increasing the design point loading capability and stable operating range of rotor and stator blading. The results of this series of tests provide overall performance and blade element data for evaluating: (1) the potential of tandem blading for extending the loading limit and stable operating range of a stage representative of a middle stage of an advanced high pressure compressor, (2) the effect of loading split between the two airfoils in tandem on the performance of tandem blading, and (3) the effects of inlet flow distortion on the stage performance. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. With uniform inlet flow, rotor B achieved a maximum adiabatic efficiency of 88.4% at design equivalent rotor speed and a pressure ratio of 1.31. The stage maximum adiabatic efficiency at design equivalent rotor speed with uniform inlet flow was 82.5% at a pressure ratio of 1.28. Tip radial and circumferential distortion of the inlet flow caused substantial reductions in surge margin.
An axisymmetric mixed-compression supersonic inlet and a single-spool turbojet engine were dynamically tested at Mach 2.5. The propulsion system was subjected to sweep-frequency sinusoidal disturbances of either inlet overboard bypass airflow. The disturbances were at a logarithmic sweep rate of 1 decade per minute. Dynamic responses were taken of signals throughout the propulsion system. Selected signals were reduced relative to the prime propulsion system parameters. The experimental data are presented in Bode plots. Most of the plots are for a frequency range of 1.0 to 50 hertz.
A molten chloride fast reactor (MCFR) includes a plurality of reflectors defining a central core having a core geometric center. A flow channel fluidically connected to the central core. The flow channel includes an outlet flow channel downstream of the central core and an inlet flow channel upstream from the central core. A primary heat exchanger (PHX) disposed outside the central core and between the outlet flow channel and the inlet flow channel. The MCFR also includes a decay heat heat exchanger (DHHX). At least a portion of the DHHX is disposed above the core geometric center, and a fuel salt is configured to circulate at least partially through the outlet flow channel, the DHHX, the PHX, the inlet flow channel, and the central core.
A simulation technique is presented for the prediction of compressor stall for axial-flow compressors for clean and distorted inlet flow. The simulation is implemented on the digital computer and uses stage stacking and lumped-volume gas dynamics. The resulting nonlinear differential equations are linearized about a steady-state operating point, and a Routh-Hurwitz stability test is performed on the linear system matrix. Parallel compressor theory is utilized to extend the technique to the distorted inlet flow problem. The method is applied to the eight-stage J85-13 compressor. Analytical stall prediction for the undistorted stall line shows good agreement with experimental results. The predicted stall line for distorted inlet flow is in agreement with experimental results only for large distortion extents and/or low distortion levels. Results for low distortion extents and high distortion level do not agree with experimental results.
Rotating stall in an axial-flow compressor is suppressed by the positioning of a fixed inlet flow divider in the annular inlet flow passage upstream of the compressor. The inlet flow divider is aligned with the flow of fluid through the duct and acts to block or interfere with any rotating wave in the inlet and thereby suppresses rotating stall in the compressor.
Numerous two-and three-dimensional computational simulations were performed for the inlet associated with the combustor model for the hypersonic propulsion experiment in the NASA Ames 16-Inch Shock Tunnel. The inlet was designed to produce a combustor-inlet flow that is nearly two-dimensional and of sufficient mass flow rate for large scale combustor testing. The three-dimensional simulations demonstrated that the inlet design met all the design objectives and that the inlet produced a very nearly two-dimensional combustor inflow profile. Numerous two-dimensional simulations were performed with various levels of approximations such as in the choice of chemical and physical models, as well as numerical approximations. Parametric studies were conducted to better understand and to characterize the inlet flow. Results from the two-and three-dimensional simulations were used to predict the mass flux entering the combustor and a mass flux correlation as a function of facility stagnation pressure was developed. Surface heat flux and pressure measurements were compared with the computed results and good agreement was found. The computational simulations helped determine the inlet low characteristics in the high enthalpy environment, the important parameters that affect the combustor-inlet flow, and the sensitivity of the inlet flow to various modeling assumptions.
Newtonian fluid turbulent flow development characteristics in inlet region of smooth concentric annulus from momentum integral equations
A flight experiment of a mechanically pumped two-phase ammonia thermal control system, incorporating a number of new component designs, has been assembled and tested in a 1-g environment. Additional microgravity tests are planned on the Space Shuttle when Shuttle flights are resumed. The primary purpose of this experiment is to evaluate the operation of a mechanically pumped two-phase ammonia system, with emphasis on determining the performance of an evaporative Two-Phase Mounting Plate. The experiment also evaluates the performance of other specially designed components, such as the two-phase reservoir for temperature control, condensing radiator/heat sink, spiral tube boiler, and pressure drop experiment. The 1-g tests have shown that start-up of the two-phase experiment is easily accomplished with only a partial fill of ammonia. The experiment maintained a constant mounting plate temperature without flow rate controls over a very wide range of heat loads, flow rates, inlet flow conditions and exit qualities. The tests also showed the successful operation of the mounting plate in the heat sharing condensing mode.