SEARCH · Engineering Papers

Results for “Hysteresis model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

DOE OSTI2022

The effect of polymer stiffness on magnetization reversal of magnetorheological elastomers

Ultrasoft magnetorheological elastomers (MREs) offer convenient real-time magnetic field control of mechanical properties that provides a means to mimic mechanical cues and regulators of cells in vitro. Here, we systematically investigate the effect of polymer stiffness on magnetization reversal of MREs using a combination of magnetometry measurements and computational modeling. Poly-dimethylsiloxane-based MREs with Young’s moduli that range over two orders of magnitude were synthesized using commercial polymers Sylgard™ 527, Sylgard 184, and carbonyl iron powder. The magnetic hysteresis loops of the softer MREs exhibit a characteristic pinched loop shape with almost zero remanence and loop widening at intermediate fields that monotonically decreases with increasing polymer stiffness. A simple two-dipole model that incorporates magneto-mechanical coupling not only confirms that micrometer-scale particle motion along the applied magnetic field direction plays a defining role in the magnetic hysteresis of ultrasoft MREs but also reproduces the observed loop shapes and widening trends for MREs with varying polymer stiffnesses.

36 MATERIALS SCIENCE↗

NASA NTRS2011

Unstructured CFD Aerodynamic Analysis of a Generic UCAV Configuration

Three independent studies from the United States (NASA), Sweden (FOI), and Australia (DSTO) are analyzed to assess the state of current unstructured-grid computational fluid dynamic tools and practices for predicting the complex static and dynamic aerodynamic and stability characteristics of a generic 53-degree swept, round-leading-edge uninhabited combat air vehicle configuration, called SACCON. NASA exercised the USM3D tetrahedral cell-centered flow solver, while FOI and DSTO applied the FOI/EDGE general-cell vertex-based solver. The authors primarily employ the Reynolds Averaged Navier-Stokes (RANS) assumption, with a limited assessment of the EDGE Detached Eddy Simulation (DES) extension, to explore sensitivities to grids and turbulence models. Correlations with experimental data are provided for force and moments, surface pressure, and off-body flow measurements. The vortical flow field over SACCON proved extremely difficult to model adequately. As a general rule, the prospect of obtaining reasonable correlations of SACCON pitching moment characteristics with the RANS formulation is not promising, even for static cases. Yet, dynamic pitch oscillation results seem to produce a promising characterization of shapes for the lift and pitching moment hysteresis curves. Future studies of this configuration should include more investigation with higher-fidelity turbulence models, such as DES.

Frink, Neal T.↗

NASA NTRS1981

Some applications of aerodynamic formulations to problems in aircraft dynamics

Two applications of mathematical modeling to aerodynamic problems are cussed. The first application is an investigation of the capacity of a nonlinear aerodynamic mathematical model to describe the aerodynamic reactions on an airfoil with a deflecting flap in transonic flow. Flow field computational methods are used to evaluate the nonlinear, unsteady aerodynamic data in terms of characteristic motions called for by the model. Histories of unconstrained motions of the flap are generated from the flap equations of motion, with the aerodynamic reactions specified by the mathematical model. In the second application wing rock is investigated. The most recent model accommodates experimental results wing rock by admitting the existence of aerodynamic hysteresis in the variation of the steady state rolling moment coefficient with roll angle is described.

Schiff, L. B.↗

NASA NTRS1995

Wavenumber selection and hysteresis in nonlinear baroclinic flow

Wavenumber transition and hysteresis in a highly unstable baroclinic flow are investigated using a high-resolution spectral numerical model. As the flow becomes more supercritical, the dominant wave gradually shifts from the most unstable wave predicted by the linear theory to a longer wave with a larger time-averaged amplitude, while the rectified mean flow attains a stronger shear at the center of the channel. The numerical results display a complex hysteresis behavior, which occurs not only between the states of different dominant wavenumbers, but also between the states of identical dominant wavenumber but of different dynamic characteristics. In a certain parameter range three stable states, each with different dominant wavenumber, are possible, and in another parameter range four stable states are possible, among them three stable states with an identical dominant wave. The numerical results suggest that a multiple weather regime exists even without external forcing in which the flow aperiodically varies between two distinct behaviors. The effects of stable higher harmonics are assessed and it is found that their presence contributes not only to the better approximation of the model solutions but also to the selection of the final equilibrium state, due to the chaotic nature of the initial transient period.

Chou, Shih-Hung↗

DOE OSTI2026

Instabilities and phase transitions in architected metamaterials: a gradient-enhanced continuum approach

Architected metamaterials such as foams and lattices exhibit a wide range of properties governed by microstructural instabilities and emerging phase transitions. Their macroscopic response–including energy dissipation during impact, large recoverable deformations, morphing between configurations, and auxetic behavior–remains difficult to capture with conventional continuum models, which often rely on discrete approaches that limit scalability. In this work, we propose a nonlocal continuum formulation that captures both stable and unstable responses of elastic architected metamaterials. The framework extends anisotropic hyperelasticity by introducing nonlocal variables and internal length scales reflective of microstructural features. Local polyconvex free-energy models are systematically augmented with two families of non-(poly)convex energies, enabling both metastable and bistable responses. Implementation in a finite element framework enables solution using a hybrid monolithic–staggered strategy. Simulations capture densification fronts, forward and reverse transitions, hysteresis loops, imperfection sensitivity, and globally coordinated auxetic modes. Overall, this framework provides a robust foundation for accelerated modeling of instability-driven phenomena in architected metamaterials, while enabling extensions to anisotropic, dissipative, and active systems as well as integration with data-driven and machine learning approaches.

42 ENGINEERING↗

NASA NTRS1988

Leading edge vortex dynamics on a pitching delta wing

A study of the dynamic behavior of the leading edge vortices on a delta wing undergoing oscillatory pitching motion is presented. A sharp edge, flat plate, delta wing having a sweep angle of 70 deg was used in this investigation. The wing was sinusoidally pitched about its 1/2 chord position at reduced frequencies ranging from k = 2(pi)fc/u = 0.05 to 0.30 at chord Reynolds numbers between 90,000 and 350,000, for angle of attack ranges of 29 to 39 deg and 0 to 45 deg. During these dynamic motions, visualization of the leading edge vortices was obtained by marking the vortices with TiCl4 introduced through ports located near the model apex. The location of vortex breakdown was recorded using high speed motion picture photography. The motion picture records were analyzed to determine vortex trajectory and breakdown position as a function of angle of attack. When the wing was sinusoidally pitched, a hysteresis was observed in the location of breakdown position. This hysteresis increased with reduced frequency. The velocity of breakdown propagation along the wing, and the phase lag between model motion and breakdown location were also determined. Detailed information was also obtained on the oscillation of breakdown position in both static and dynamic cases.

Lemay, S. P.↗

NASA NTRS1992

Evaluation of electrolytic tilt sensors for measuring model angle of attack in wind tunnel tests

The results of a laboratory evaluation of electrolytic tilt sensors as potential candidates for measuring model attitude or angle of attack in wind tunnel tests are presented. The performance of eight electrolytic tilt sensors was compared with that of typical servo accelerometers used for angle-of-attack measurements. The areas evaluated included linearity, hysteresis, repeatability, temperature characteristics, roll-on-pitch interaction, sensitivity to lead-wire resistance, step response time, and rectification. Among the sensors being evaluated, the Spectron model RG-37 electrolytic tilt sensors have the highest overall accuracy in terms of linearity, hysteresis, repeatability, temperature sensitivity, and roll sensitivity. A comparison of the sensors with the servo accelerometers revealed that the accuracy of the RG-37 sensors was on the average about one order of magnitude worse. Even though a comparison indicates that the cost of each tilt sensor is about one-third the cost of each servo accelerometer, the sensors are considered unsuitable for angle-of-attack measurements. However, the potential exists for other applications such as wind tunnel wall-attitude measurements where the errors resulting from roll interaction, vibration, and response time are less and sensor temperature can be controlled.

Wong, Douglas T.↗

NASA NTRS2001

Mathematical Modeling of Ni/H2 and Li-Ion Batteries

The modelling effort outlined in this viewgraph presentation encompasses the following topics: 1) Electrochemical Deposition of Nickel Hydroxide; 2) Deposition rates of thin films; 3) Impregnation of porous electrodes; 4) Experimental Characterization of Nickel Hydroxide; 5) Diffusion coefficients of protons; 6) Self-discharge rates (i.e., oxygen-evolution kinetics); 7) Hysteresis between charge and discharge; 8) Capacity loss on cycling; 9) Experimental Verification of the Ni/H2 Battery Model; 10) Mathematical Modeling Li-Ion Batteries; 11) Experimental Verification of the Li-Ion Battery Model; 11) Integrated Power System Models for Satellites; and 12) Experimental Verification of Integrated-Systems Model.

Weidner, John W.↗

DOE OSTI2023

Encapsulation Residual Stress and Ferrite Loss in Inductive Coil Assemblies

As inductive wireless charging reaches higher power levels, thermal management and mechanical durability become more critical. To address these concerns, past works have demonstrated the benefit of encapsulating coil assemblies in thermally conductive materials. However, due to the sensitivity of the MnZn ferrites commonly used in coil assemblies to mechanical stress, care must be taken to avoid creating large stresses in the ferrite that cause higher hysteresis loss. The stress formation in the encapsulant curing process is overviewed and modeled and an experiment is performed to demonstrate the effect in a small-scale coil assembly. Finally, the effect is shown in the reduced coil-coil efficiency of a first generation high power inductive power transfer prototype using a stiff epoxy compared to better performance in a second prototype using a softer thermally-conductive silicone encapsulant.

Foote, Andrew↗

NASA NTRS1989

On damping mechanisms in beams

A partial differential equation model of a cantilevered beam with a tip mass at its free end is used to study damping in a composite. Four separate damping mechanisms consisting of air damping, strain rate damping, spatial hysteresis and time hysteresis are considered experimentally. Dynamic tests were performed to produce time histories. The time history data is then used along with an approximate model to form a sequence of least squares problems. The solution of the least squares problem yields the estimated damping coefficients. The resulting experimentally determined analytical model is compared with the time histories via numerical simulation of the dynamic response. The procedure suggested here is compared with a standard modal damping ratio model commonly used in experimental modal analysis.

Banks, H. T.↗

NASA NTRS1991

On damping mechanisms in beams

Banks, H. T.↗

DOE OSTI2024

Heat Transport Hysteresis Generated Through Frequency Switching of a Time-Dependent Temperature Gradient

A stochastic energetics framework is applied to examine how periodically shifting the frequency of a time-dependent oscillating temperature gradient affects heat transport in a nanoscale molecular model. We specifically examine the effects that frequency switching, i.e., instantaneously changing the oscillation frequency of the temperature gradient, has on the shape of the heat transport hysteresis curves generated by a particle connected to two thermal baths, each with a temperature that is oscillating in time. Analytical expressions are derived for the energy fluxes in/out of the system and the baths, with excellent agreement observed between the analytical expressions and the results from nonequilibrium molecular dynamics simulations. We find that the shape of the heat transport hysteresis curves can be significantly altered by shifting the frequency between fast and slow oscillation regimes. We also observe the emergence of features in the hysteresis curves such as pinched loops and complex multi-loop patterns due to the frequency shifting. The presented results have implications in the design of thermal neuromorphic devices such as thermal memristors and thermal memcapacitors.

36 MATERIALS SCIENCE↗

NASA NTRS1987

Nonlinear transient analysis of joint dominated structures

A residual force technique is presented that can perform the transient analyses of large, flexible, and joint dominated structures. The technique permits substantial size reduction in the number of degrees of freedom describing the nonlinear structural models and can account for such nonlinear joint phenomena as free-play and hysteresis. In general, joints can have arbitrary force-state map representations but these are used in the form of residual force maps. One essential feature of the technique is to replace the arbitrary force-state maps describing the nonlinear joints with residual force maps describing the truss links. The main advantage of this replacement is that the incrementally small relative displacements and velocities across a joint are not monitored directly thereby avoiding numerical difficulties. Instead, very small and 'soft' residual forces are defined giving a numerically attractive form for the equations of motion and thereby permitting numerically stable integration algorithms. The technique was successfully applied to the transient analyses of a large 58 bay, 60 meter truss having nonlinear joints. A method to perform link testing is also presented.

Chapman, J. M.↗

NASA NTRS1994

Development of a multicomponent force and moment balance for water tunnel applications, volume 1

The principal objective of this research effort was to develop a multicomponent strain gauge balance to measure forces and moments on models tested in flow visualization water tunnels. An internal balance was designed that allows measuring normal and side forces, and pitching, yawing and rolling moments (no axial force). The five-components to applied loads, low interactions between the sections and no hysteresis. Static experiments (which are discussed in this Volume) were conducted in the Eidetics water tunnel with delta wings and a model of the F/A-18. Experiments with the F/A-18 model included a thorough baseline study and investigations of the effect of control surface deflections and of several Forebody Vortex Control (FVC) techniques. Results were compared to wind tunnel data and, in general, the agreement is very satisfactory. The results of the static tests provide confidence that loads can be measured accurately in the water tunnel with a relatively simple multicomponent internal balance. Dynamic experiments were also performed using the balance, and the results are discussed in detail in Volume 2 of this report.

Suarez, Carlos J.↗

DOE OSTI2024

Hysteresis between gas breakdown and plasma discharge

In direct-current (DC) discharge, it is well known that hysteresis is observed between the Townsend (gas breakdown) and glow regimes. Forward and backward voltage sweep is performed using a one-dimensional particle-in-cell Monte Carlo collision (PIC-MCC) model considering a ballast resistor. When increasing the applied voltage after reaching the breakdown voltage (V b ), transition from Townsend to glow discharges is observed. When decreasing the applied voltage from the glow regime, the discharge voltage (V d ) between the anode–cathode gap can be smaller than the breakdown voltage, resulting in a hysteresis, which is consistent with experimental observations. Next, the PIC-MCC model is used to investigate the self-sustaining voltage (V s ) in the presence of finite initial plasma densities between the anode and cathode gap. It is observed that the self-sustaining voltage coincides with the discharge voltage obtained from the backward voltage sweep. In addition, the self-sustaining voltage decreases with increased initial plasma density and saturates above a certain initial plasma density, which indicates a change in plasma resistivity. The decrease in self-sustaining voltage is associated with the electron heat loss at the anode for the low pd (rarefied) regime. In the high pd (collisional) regime, the ion energy loss toward the cathode due to the cathode fall and the inelastic collision loss of electrons in the bulk discharge balance out. Finally, it is demonstrated that the self-sustaining voltage collapses to a singular value, despite the presence of a initial plasma, for microgaps when field emission is dominant, which is also consistent with experimental observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1986

Testing experience with unheated stain-gage balances in the NTF

A series of cryogenic (cryo) cycles was conducted in the cryo chamber at the National Transonic Facility (NTF) in order to identify the cause of apparent strain shifts in axial force with temperature for the Pathfinder I model and to minimize their effects. The results of the investigation indicated that the major cause of axial force end point shifts and thermal hysteresis loops was the thickness of the Teflon insulation on the instrumentation wires crossing the balance. By reducing the thickness of the insulation and the total number and size of the wires, apparent strain values were achieved for the model with instrumentation wires which were nearly identical to those for the model without wires. Because of the special design features used, the balance output was very accurate and repeatable over the entire NTF temperature range, even with balance thermal gradients as large as 64 F and transient conditions as large as 3 F/minute.

Jacobs, Peter F.↗

DOE OSTI2023

Element-Specific Study of Magnetic Anisotropy and Hardening in SmCo 5– x Cu x Thin Films

This work investigates the effect of copper substitution on the magnetic properties of SmCo 5 thin films synthesized by molecular beam epitaxy. A series of thin films with varying concentrations of Cu were grown under otherwise identical conditions to disentangle structural and compositional effects on the magnetic behavior. The combined experimental and theoretical studies show that Cu substitution at the Co 3g sites not only stabilizes the formation of the SmCo 5 structure but also enhances magnetic anisotropy and coercivity. Density functional theory calculations indicate that Sm(Co 4 Cu 3g ) 5 possesses a higher single-ion anisotropy as compared to pure SmCo 5 . In addition, X-ray magnetic circular dichroism reveals that Cu substitution causes an increasing decoupling of the Sm 4f and Co 3d moments. Scanning transmission electron microscopy confirms predominantly SmCo 5 phase formation and reveals nanoscale inhomogeneities in the Cu and Co distribution. Our study based on thin film model systems and advanced characterization as well as modeling reveals novel aspects of the complex interplay of intrinsic and extrinsic contributions to magnetic hysteresis in rare-earth-based magnets, i.e., the combination of increased intrinsic anisotropy due to Cu substitution and the extrinsic effect of inhomogeneous elemental distribution of Cu and Co.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Collective Ferromagnetism of Artificial Square Spin Ice

In this work, we study the temperature and magnetic field dependence of the total magnetic moment of large-area permalloy artificial square spin ice arrays. The temperature dependence and hysteresis behavior are consistent with the coherent magnetization reversal expected in the Stoner-Wohlfarth model, with clear deviations due to interisland interactions at small lattice spacing. Through micromagnetic simulations, we explore this behavior and demonstrate that the deviations result from increasingly complex magnetization reversal at small lattice spacing, induced by interisland interactions, and depending critically on details of the island shapes. These results establish new means to tune the physical properties of artificial spin ice structures and other interacting nanomagnet systems, such as patterned magnetic media.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗