SEARCH · Engineering Papers

Results for “Geometry Visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Some observations on the occurrence of striation heating

Various wind tunnel flow visualization techniques have revealed the presence of striations on the surface of both simple geometries and complex winged entry configurations over a wide range of test conditions. The striations are attributed to streamwise vortices embedded in the boundary layer which produce locally enhanced heating levels. Mechanisms for such vortex formation are suggested based on observation of their occurrence on the simple configurations. These mechanisms are then related to striations observed in the wind tunnel on windward surfaces, swept wing leading edges and on the side fuselage of winged entry bodies. Flight data obtained on the side fuselage of ASSET and Shuttle support the conclusions derived from wind tunnel results. Quantitative criteria for the appearance of striations resulting from some of these mechanisms are presented. It is shown that the presence of embedded vorticity may be a consideration in the design of thermal protection systems for advanced winged entry vehicles.

Kipp, H. W.↗

NASA NTRS1991

Interactive design of hypersonic waverider geometries

The paper deals with an inverse design code utilizing the method of oscillating cones; the code integrated into an interactive graphics software package allows manipulation of both the exit-plane shock profile and leading edge of the vehicle. Another interactive feature of the system is the ability to vary freestream conditions and reevaluate the governing conditions. The development of the oscillating cones is shown on five classes each of which is chosen to demonstrate an aspect of improved design flexibility over previous studies. Results are evaluated using a robust flow solver, insuring that the shock shapes specified in the design process are recovered. It is pointed out that the expanded range of waverider geometries that may be generated using the oscillating cones technique may provide insight into visually oriented optimization parameters such as volumetric efficiency and practical planform.

Center, K. B.↗

NASA NTRS2014

Investigating Surveillance Performance for UAS Detect-and-Avoid Systems

Most unmanned aircraft systems will be required to be equipped with a detect-and-avoid system that is capable of maintaining appropriate separation from other aircraft. One of the critical components of detect-and-avoid systems is a surveillance system that identifies potential threat aircraft in real time and tracks these aircraft so that their future trajectories may be used to predict conflicts. The performance of the detect-and-avoid system generally depends on technical parameters of the surveillance system, such as the surveillance range. The quantitative requirements for detect-and-avoid systems will be determined to meet safety metrics for the operation of unmanned aircraft systems in the National Airspace System. This study employs a sensor model comprised of the surveillance range, and horizontal and vertical fields of regard that mainly characterize the overall performance of a surveillance system. In this study, potential metrics for evaluating the performance of a surveillance system were investigated through fast-time simulation with a traffic scenario that included both proposed unmanned aircraft flights and historical visual flight rule aircraft tracks. Using the simulation results, an overall analysis of encounter geometry highlights the encounter characteristics that relate surveillance parameters to safety metrics and detect-and-avoid system performance. Then, given several candidate surveillance volumes, performance and safety metrics are derived; these metrics include the ratio of undetected and late-detected violations and the time to violation at first detection. These example metrics demonstrate the utility of the database of encounters created in this work, a database which will be useful in the derivation of required detect-and-avoid surveillance system requirements.

Lee, Seung Man↗

DOE OSTI2025

Design Overview of a High-Pressure Helium Flow Visualization Apparatus for Blanket Cooling Studies

Cooling of the fusion blanket first wall remains a significant challenge given the adverse conditions of heat and particle flux encountered near the plasma. Helium emerges as an attractive cooling candidate because of its chemical and neutronic inertness and separability from hydrogenic species (e.g. tritium). Because of the low thermal mass of helium, optimization of these coolant channels is warranted to provide high heat transfer performance at low pumping costs. Increasingly, computational fluid dynamics (CFD) simulations are employed to model and optimize these flow channels, and accompanying experimental data are needed to validate the predictions of these models. To provide the aforementioned experimental data, a high-pressure helium flow visualization upgrade has been designed for the Helium Flow Loop Experiment facility. This apparatus was built to American Society of Mechanical Engineers boiler and pressure vessel standards to withstand operating pressure of 4 MPa and mated to high-pressure glass windows. Seedless flow visualization is performed via high-speed background oriented schlieren (BOS), with image correlation used for time-resolved two-dimensional velocimetry at frequencies in excess of 60 kHz. Rectangular flow channel test articles are additively manufactured via laser powder bed fusion and installed into this visualization apparatus, with one-sided heating supplied by resistive heaters. In conclusion, the chosen test geometries were informed by prior CFD simulations, and the helium flow structures observed via BOS (detachment, recirculation, etc.) will be used for the validation of these accompanying models, in support of the design and optimization of blanket cooling channel configurations.

Helium flow↗

DOE OSTI2021

Disentangling ferroelectric domain wall geometries and pathways in dynamic piezoresponse force microscopy via unsupervised machine learning

In this work, domain switching pathways in ferroelectric materials visualized by dynamic piezoresponse force microscopy (PFM) are explored via variational autoencoder, which simplifies the elements of the observed domain structure, crucially allowing for rotational invariance, thereby reducing the variability of local polarization distributions to a small number of latent variables. For small sampling window sizes the latent space is degenerate, and variability is observed only in the direction of a single latent variable that can be identified with the presence of domain wall. For larger window sizes, the latent space is 2D, and the disentangled latent variables can be generally interpreted as the degree of switching and complexity of domain structure. Applied to multiple consecutive PFM images acquired while monitoring domain switching, the polarization switching mechanism can thus be visualized in the latent space, providing insight into domain evolution mechanisms and their correlation with the microstructure.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

NASA NTRS2003

Accelerating Large Data Analysis By Exploiting Regularities

We present techniques for discovering and exploiting regularity in large curvilinear data sets. The data can be based on a single mesh or a mesh composed of multiple submeshes (also known as zones). Multi-zone data are typical to Computational Fluid Dynamics (CFD) simulations. Regularities include axis-aligned rectilinear and cylindrical meshes as well as cases where one zone is equivalent to a rigid-body transformation of another. Our algorithms can also discover rigid-body motion of meshes in time-series data. Next, we describe a data model where we can utilize the results from the discovery process in order to accelerate large data visualizations. Where possible, we replace general curvilinear zones with rectilinear or cylindrical zones. In rigid-body motion cases we replace a time-series of meshes with a transformed mesh object where a reference mesh is dynamically transformed based on a given time value in order to satisfy geometry requests, on demand. The data model enables us to make these substitutions and dynamic transformations transparently with respect to the visualization algorithms. We present results with large data sets where we combine our mesh replacement and transformation techniques with out-of-core paging in order to achieve significant speed-ups in analysis.

Moran, Patrick J.↗

NASA NTRS1986

The effect of perspective geometry on judged direction in spatial information instruments

Attention is given to the methodology and results of an experiment examining design aspects of panel-mounted displays that (1) incorporate a planar grid in their symbology, (2) subtend a narrow visual angle, and (3) are mounted so that they can be viewed face-on rather than obliquely. An analysis of direction judgments in such perspective displays shows that the perspective geometry of the stimulus image has a significant effect on direction judgment accuracy. Target elevation direction is generally overestimated; azimuth error varies sinusoidally with target azimuth direction, and is modulated by field-of-view angle.

Mcgreevy, Michael Wallace↗

DOE OSTI2025

Immersive Scientific Visualization of Molten-Salt Reactor Waste Characteristics Using Virtual Reality

Immersive visualization is changing how we explore, communicate, and understand complex scientific systems. In nuclear energy, an area in which data are often multidimensional, time-dependent, and difficult to interpret, virtual reality (VR) represents a powerful and intuitive informational medium. This work introduces a VR-based platform that visualizes the post-shutdown behavior and waste management lifecycle of molten-salt reactors (MSRs), a next-generation reactor type with unique operational and safety characteristics. The platform, built in Unity, is streamed on the Meta Quest 3 headset. It transforms high-fidelity simulation data into an interactive, immersive experience. Users can explore time-dependent reactor characteristics such as nuclide decay, which is a key factor for evaluating reactor waste strategies. The datasets were generated using the MOOSE (Multiphysics Object-Oriented Simulation Environment) framework and then processed through ParaView scripting for smooth integration into Unity. From a visualization standpoint, the platform emphasizes spatial storytelling, temporal exploration, and user-centered interaction. Users can navigate 3D reactor geometries, slice through volumetric data, and manipulate time to observe how physical phenomena evolve. Real-scale rendering and embodied interaction make the experience feel tangible. The interface is designed to be accessible, even to those without nuclear or simulation expertise. This lowers the barrier for stakeholders, policymakers, and the general public, while still supporting expert analysis and collaborative decision-making. This work shows how immersive visualization can function as both a scientific tool and a communication interface. By integrating simulation, processing, and visualization into a cohesive workflow, we offer a scalable framework for immersive scientific storytelling. The modular design supports future extensions to other reactor types and lifecycle stages, from shutdown to long-term storage, making the platform adaptable for both research and outreach.

99 - GENERAL AND MISCELLANEOUS↗

DOE OSTI2023

CatMass : software for calculating optimal sample masses for X-ray absorption spectroscopy experiments involving complex sample compositions

This paper presents software for calculating the optimal mass of samples with complex compositions ( e.g. supported metal catalysts) for X-ray absorption spectroscopy (XAS) and scattering measurements. The ability to calculate the sample mass and other relevant parameters needed for an XAS measurement allows experimentalists to be better prepared in terms of detector selection, energy range of scan and overall time needed to complete the measurement, thus increasing efficiency. CatMass builds on existing sample mass calculators allowing users to determine the optimum sample preparation, collection geometry, usable energy range for a scan and approximate edge step of the absorption event. Visualization tools present the absorption calculation results in a format familiar to XAS experimentalists, with the added ability to save calculations and plots for future reference or recalculation. CatMass is a program broadly applicable in catalysis and is helpful for users with complex samples due to composition/stoichiometry or multiple competing elements.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Residual stress and microstructure in IN718-René41 graded superalloy fabricated by laser blown directed energy deposition

Additively printed Ni-based superalloy with a compositionally graded transition from IN718 to René41 was fabricated by laser blown-powder directed energy deposition (DED/LB-M), with the goals of meeting location-specific temperature capability and reducing component cost for hot gas path turbine components. Residual stress distribution in thin wall specimens with three sets of DED build parameters in the as-built and stress-relieved states was measured by neutron diffraction. For calculating residual stress, the calculated d0 method was found to be more appropriate as stress-free reference than using the lattice spacing measured from the stress-relief heat treated specimens. Longer dwell time (lower interpass temperature), higher energy input, smaller layer thickness resulted in a higher magnitude of tensile residual stresses at edges and compressive residual stresses at center of the specimens. The residual stress results did not show a strong dependence on graded compositions, indicating that the residual stress build-up was more geometry and process dependent. Non-destructive neutron imaging based on the attenuation coefficient qualitatively visualized the compositional variation in the bulk and showed good agreement with quantitative Electron Probe Micro-Analysis (EPMA) measurement. Grain structure, texture, and residual plastic strain along the build direction were characterized by Electron Backscatter Diffraction (EBSD). Long columnar grains with (001) preferred grain orientation were dominant along the build direction. Compositional change did not show an obvious effect on the epitaxial growth of dendrites and the continuation of the columnar grains. Residual plastic strain was relatively low in the as-built specimens.

36 MATERIALS SCIENCE↗

NASA NTRS1974

Development of a Fowler flap system for a high performance general aviation airfoil

A two-dimensional wind-tunnel evaluation of two Fowler flap configurations on the new GA(W)-1 airfoil was conducted. One configuration used a computer-designed 29-percent chord Fowler flap. The second configuration was modified to have increased Fowler action with a 30-percent chord flap. Force, pressure, and flow-visualization data were obtained at Reynolds numbers of 2.2 million to 2.9 million. Optimum slot geometry and performance were found to be close to computer predictions. A C sub L max of 3.8 was achieved. Optimum flap deflection, slot gap, and flap overlap are presented as functions of C sub L. Tests were made with the lower surface cusp filled in to show the performance penalties that result. Some data on the effects of adding vortex generators and hinged-plate spoilers were obtained.

Wentz, W. H., Jr.↗

NASA NTRS1990

Hybrid vision activities at NASA Johnson Space Center

NASA's Johnson Space Center in Houston, Texas, is active in several aspects of hybrid image processing. (The term hybrid image processing refers to a system that combines digital and photonic processing). The major thrusts are autonomous space operations such as planetary landing, servicing, and rendezvous and docking. By processing images in non-Cartesian geometries to achieve shift invariance to canonical distortions, researchers use certain aspects of the human visual system for machine vision. That technology flow is bidirectional; researchers are investigating the possible utility of video-rate coordinate transformations for human low-vision patients. Man-in-the-loop teleoperations are also supported by the use of video-rate image-coordinate transformations, as researchers plan to use bandwidth compression tailored to the varying spatial acuity of the human operator. Technological elements being developed in the program include upgraded spatial light modulators, real-time coordinate transformations in video imagery, synthetic filters that robustly allow estimation of object pose parameters, convolutionally blurred filters that have continuously selectable invariance to such image changes as magnification and rotation, and optimization of optical correlation done with spatial light modulators that have limited range and couple both phase and amplitude in their response.

Juday, Richard D.↗

NASA NTRS2006

Visualization of a Capsule Entry Vehicle Reaction-Control System (RCS) Thruster

Planar laser-induced fluorescence (PLIF) was used to visualize the reaction control system (RCS) jet flow emanating from the aft-body of an Apollo-geometry capsule test article in the NASA Langley Research Center 31-Inch Mach 10 Air wind tunnel. The RCS jet was oriented normal to the aft surface of the model and had a nominal Mach number of 2.94. The composition of the jet gas by mass was 95% nitrogen (N2) and 5% nitric oxide (NO). The RCS jet flowrate varied between zero and 0.5 standard liters per minute and the angle of attack and tunnel stagnation pressure were also varied. PLIF was used to excite the NO molecules for flow visualization. These flow visualization images were processed to determine the trajectory and to quantify the flapping of the RCS jet. The spatial resolution of the jet trajectory measurement was about 1 mm and the single-shot precision of the measurement was estimated to be 0.02 mm in the far field of the jet plume. The jet flapping, measured by the standard deviation of the jet centerline position was as large as 0.9 mm, while the jet was 1.5-4 mm in diameter (full width at half maximum). Schlieren flow visualization images were obtained for comparison with the PLIF. Surface pressures were also measured and presented. Virtual Diagnostics Interface (VIDI) technology developed at NASA Langley was used to superimpose and visualize the data sets. The measurements demonstrate some of the capabilities of the PLIF method while providing a test case for computational fluid dynamics (CFD) validation.

Danehy, P. M.↗

DOE OSTI2022

Role of nanocellulose in tailoring electroanalytical performance of hybrid nanocellulose/multiwalled carbon nanotube electrodes

Abstract Nanocellulose has emerged as a promising green dispersant for carbon nanotubes (CNTs), and there is an increasing trend in developing nanocellulose/CNT hybrid materials for electrochemical detection of various small molecules. However, there have been very few comprehensive studies investigating the role of nanocellulosic material properties upon the electroanalytical performance of the resultant hybrid electrodes. In this work, we demonstrate the influence of both nanocellulose functionalization and geometry, utilizing sulfated cellulose nanocrystals, sulfated cellulose nanofibers, and TEMPO-oxidized cellulose nanofibers. Transmission electron microscopy tomography enables direct visualization of the effect of nanocellulosic materials on the hybrid architectures. High resolution X-ray absorption spectroscopy verifies that the chemical nature of CNTs in the different hybrids is unmodified. Electroanalytical performances of the different nanocellulose/CNT hybrid electrodes are critically evaluated using physiologically relevant biomolecules with different charge such as, dopamine (cationic), paracetamol (neutral), and uric acid (anionic). The hybrid electrode containing fibrillar nanocellulose geometry with a high degree of sulfate group functionalization provides the highest electroanalytical sensitivity and strongest enrichment towards all studied analytes. These results clearly demonstrate for the first time, the extent of tailorability upon the electroanalytical response of nanocellulose/CNT hybrid electrodes towards different biomolecules, offered simply by the choice of nanocellulosic materials.

Durairaj, Vasuki↗

NASA NTRS1994

A qualitative and quantitative laser-based computer-aided flow visualization method

The experimental approach presented here offers a nonintrusive, qualitative and quantitative evaluation of full field flow patterns applicable in various geometries in a variety of fluids. This Full Flow Field Tracking (FFFT) Particle Image Velocimetry (PIV) technique, by means of particle tracers illuminated by a laser light sheet, offers an alternative to Laser Doppler Velocimetry (LDV), and intrusive systems such as Hot Wire/Film Anemometry. The method makes obtainable the flow patterns, and allows quantitative determination of the velocities, accelerations, and mass flows of an entire flow field. The method uses a computer based digitizing system attached through an imaging board to a low luminosity camera. A customized optical train allows the system to become a long distance microscope (LDM), allowing magnifications of areas of interest ranging up to 100 times. Presented in addition to the method itself, are studies in which the flow patterns and velocities were observed and evaluated in three distinct geometries, with three different working fluids. The first study involved pressure and flow analysis of a brush seal in oil. The next application involved studying the velocity and flow patterns in a cowl lip cooling passage of an air breathing aircraft engine using water as the working fluid. Finally, the method was extended to a study in air to examine the flows in a staggered pin arrangement located on one side of a branched duct.

Canacci, Victor A.↗

NASA NTRS1987

An interactive approach to surface-fitting complex geometries for flowfield applications

Numerical flowfield methods require a geometry subprogram which can calculate body coordinates, slopes, and radii of curvature for typical aircraft and spacecraft configurations. The objective of this paper is to develop a new surface-fitting technique which addresses two major problems with existing geometry packages: computer storage requirements and the time required of the user for the initial set-up of the geometry model. In the present method, coordinates of cross sections are fit in a least-squares sense using segments of general conic sections. After fitting each cross section, the next step is to blend the cross-sectional curve-fits in the longitudinal direction using general conics to fit specific meridional half-planes. For the initial setup of the geometry model, an interactive, completely menu-driven computer code has been developed to allow the user to make modifications to the initial fit for a given cross section or meridional cut. Graphic displays are provided to assist the user in the visualization of the effect of each modification. The completed model may be viewed from any angle using the code's three-dimensional graphics package. Geometry results for the modeling of the Space Shuttle and a proposed Aeroassist Flight Experiment (AFE) geometry are presented, in addition to calculated heat-transfer rates based on these models.

Dejarnette, Fred R.↗

NASA NTRS2008

A Study of Visualization for Mathematics Education

Graphical representations such as figures, illustrations, and diagrams play a critical role in mathematics and they are equally important in mathematics education. However, graphical representations in mathematics textbooks are static, Le. they are used to illustrate only a specific example or a limited set. of examples. By using computer software to visualize mathematical principles, virtually there is no limit to the number of specific cases and examples that can be demonstrated. However, we have not seen widespread adoption of visualization software in mathematics education. There are currently a number of software packages that provide visualization of mathematics for research and also software packages specifically developed for mathematics education. We conducted a survey of mathematics visualization software packages, summarized their features and user bases, and analyzed their limitations. In this survey, we focused on evaluating the software packages for their use with mathematical subjects adopted by institutions of secondary education in the United States (middle schools and high schools), including algebra, geometry, trigonometry, and calculus. We found that cost, complexity, and lack of flexibility are the major factors that hinder the widespread use of mathematics visualization software in education.

Daugherty, Sarah C.↗

DOE OSTI2026

Flow dynamics and heat transfer in simplified battery energy storage systems with heated battery modules

Large-scale energy storage systems (ESSs) composed of batteries show promise in addressing current energy challenges, but dissipation of generated heat is important. Here, this paper focuses on buoyant convective flows in simplified ESS battery racks. Natural convection is not generally the primary cooling strategy but can be important in abnormal scenarios where there is module overheat or potentially thermal runaway. We use computational fluid dynamics to investigate the flow dynamics and heat transfer mechanisms in a simplified parameterized rack design. Despite its simplicity, this configuration produces many of the relevant features expected in real ESSs without details of module geometry or hardware, allowing broad conclusions independent of manufacture-specific designs. We start by providing visualizations of the flowfield and measurements of entrainment, heat flux, and pressure. To characterize the dependence on the system parameters, we develop an integral-scale analysis of the average temperature equation to highlight the dominant source terms. We use results from this analysis to derive a steady network model composed of simple algebraic expressions to provide first-order predictions of entrainment through the rack. The network model leads to a linear scaling of the Reynolds number based on convective mass flux with respect to the Grashof number based on the heat source. We deduce empirical relationships that relate the heat exchanged between modules using a surface-averaged Nusselt number as a function of the local Reynolds and Rayleigh numbers. Lastly, we investigate how space between the modules and rack in the spanwise direction creates flow bypass, resulting in different flow pathways.

Battery thermal management↗