SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The development of composite materials for aircraft applications is addressed with specific consideration of physical properties, structural concepts and analysis, manufacturing, reliability, and life prediction. The design and flight testing of composite ultralight gliders is documented. Advances in computer aided design and methods for nondestructive testing are also discussed.
Aerodynamic characteristics of wing model gliders and bird wings in particular are discussed. Wind tunnel measurements and aerodynamics of small Reynolds numbers are enumerated. Airfoil behavior in the critical transition from laminar to turbulent boundary layer, which is more important to bird wing models than to large airplanes, was observed. Experimental results are provided, and an artificial bird wing is described.
The NASA early experimental program for parawing and lifting body spacecraft recovery concepts is discussed. Simple hand drawings, in-house construction, and crude drop tests were used in lieu of a thorough stress analysis. The parawing (parasev) was controlled by manually shifting the center of gravity with respect to the center of pressure; the craft would take off while being towed at 40 KIAS. The M-2 lifting body was originally constructed with a 3/32 in. mahogany skin by a glider manufacturer and employed general aviation aircraft nose and main wheel assemblies. A minimum altitude of 200 ft was found acceptable for release of the parasev, allowing the pilot time to adjust for transients incurred at the tow release. A small landing assist rocket was furnished for the M-2/F-2 and X-24A lifting bodies to enhance stability, and landings at a maximum lift/drag ratio of 2.8 were successfully completed. The data gained were eventually applied in the development of the Shuttle.
System specifications, launch procedures, costs, payloads, and evolutionary developments in the STS are outlined. The Shuttle employs solid propellant boosters and an external cryogenic fuel tank to achieve LEO for the manned Orbiter, which can maneuver in space and return to earth like a glider. The Shuttle can place a maximum payload of 30 tons into a 275 km orbit. An Inertial Upper Stage and a Spinning Solid Upper Stage will be carried by the Orbiter in its bay and used to boost satellites into GEO. Additionally, the Orbiter is equipped with a remote manipulator system for removing cargo from the bay and for grappling satellites for retrieval or repair. The Shuttle is presently launched from Kennedy Space Center, while a second launch site is being prepared at Vandenberg AFB. The STS is intended to perform 28-40 flights per year by the end of the 1980s. An Orbital Transfer Vehicle is under study to increase the size and length of payloads which can be placed in GEO using the Shuttle. Utilization of the concept is noted to be connected with the development of a permanently manned space station.
Progress is reported in studies of constituent materials composite materials, generic structural elements, processing science technology, and maintaining long-term structural integrity. Topics discussed include: mechanical properties of high performance carbon fibers; fatigue in composite materials; experimental and theoretical studies of moisture and temperature effects on the mechanical properties of graphite-epoxy laminates and neat resins; numerical investigations of the micromechanics of composite fracture; delamination failures of composite laminates; effect of notch size on composite laminates; improved beam theory for anisotropic materials; variation of resin properties through the thickness of cured samples; numerical analysis composite processing; heat treatment of metal matrix composites, and the RP-1 and RP2 gliders of the sailplane project.
Over the past several years the NASA Ames-Dryden Flight Research Facility at Edwards Air Force Base has developed a variety of flight flutter and ground test techniques which have been applied to an assortment of new or modified aerospace research vehicles. This paper presents a summary of these techniques and the experiences gained from these applications. Topics discussed include the roles of ground vibration testing, flight flutter testing, wind tunnel flutter model testing, predictive analyses, and aeroservoelastic considerations. Data are presented for a wide variety of aircraft, including remotely piloted vehicles, modern fighters with relaxed static stability and highly augmented flight control systems, aircraft modified for laminar flow control experiments, a glider modified for deep stall tests, and aircraft with skewed or forward swept wings. The conclusions include a brief discussion of future directions in flight flutter testing at Ames-Dryden.
Interactions among engineering disciplines and subsystems in engineering system design are surveyed and specific instances of such interactions are described. Examination of the interactions that a traditional design process in which the numerical values of major design variables are decided consecutively is likely to lead to a suboptimal design. Supporting numerical examples are a glider and a space antenna. Under an alternative approach introduced, the design and its sensitivity data from the subsystems and disciplines are generated concurrently and then made available to the system designer enabling him to modify the system design so as to improve its performance. Examples of a framework structure and an airliner wing illustrate that approach.
Problems related to interdisciplinary interactions in the design of a complex engineering systems are examined with reference to aerospace applications. The interdisciplinary optimization problems examined include those dealing with controls and structures, materials and structures, control and stability, structure and aerodynamics, and structure and thermodynamics. The discussion is illustrated by the following specific applications: integrated aerodynamic/structural optimization of glider wing; optimization of an antenna parabolic dish structure for minimum weight and prescribed emitted signal gain; and a multilevel optimization study of a transport aircraft.
In the present study of maneuvering reentry vehicles employing skipping and gliding flight paths, attention is given to aerodynamic heating pulses during longitudinal flight and lateral maneuvers. While skipping vehicles can achieve longer ranges than gliding ones, the deceleration loads can be an order of magnitude higher and involve heating rates 4-5 times higher, even for shallow entries, therefore requiring much heavier structural components and heavier thermal protection systems than gliders. A total lateral range of 8000 km is noted to be achievable by a gliding aerodynamic maneuver involving a 90-deg turn initiated at entry.
Work done over the past two years for the NASA/Johnson Space Center on possible evolutionary paths of the present Space Shuttle Orbiter and system to meet the goals of enhanced safety, mission suitability economy, and robustness is summarized in this paper. Three vehicle concepts are described: an advanced technology one-and-one-half stage vehicle, a near-term evolved Space Shuttle system closely related to today's Orbiter in concept and appearance, and an Orbiter-Glider which might be appropriate for use with emerging large space launch vehicles.
Three missions have been identified by NASA for a Space Shuttle-supplementing Alternate Transportation System (ATS) encompassing combinations of booster vehicles, crew modules, and service modules: (1) to achieve manned access to orbit for Space Station crew rotation every 90 days, (2) the lofting of a logistics module resupplying the Space Station every 180 days, and (3) the simultaneous launch of both crews and logistics to the Space Station. A reentry glider is considered, in conjunction with the Space Shuttle's unmanned cargo version and the Apollo manned capsule, as an important ATS element. The Titan IV/NUS is used as a booster.
Interactions among engineering disciplines and subsystems in engineering system design are surveyed and specific instances of such interactions are described. Examination of the interactions that a traditional design process in which the numerical values of major design variables are decided consecutively is likely to lead to a suboptimal design. Supporting numerical examples are a glider and a space antenna. Under an alternative approach introduced, the design and its sensitivity data from the subsystems and disciplines are generated concurrently and then made available to the system designer enabling him to modify the system design so as to improve its performance. Examples of a framework structure and an airliner wing illustrate that approach.
This paper presents an analysis of the atmospheric maneuvering capability of a vehicle designated to land on the Martian surface, together with an analysis of the entry environment encountered by the vehicle. A maximum lift/drag ratio of 2.3 was used for all trajectory calculations. The maximum achievable lateral ranges varied from about 3400 km to 2500 km for entry velocities of 5 km/s (from a highly elliptical Martian orbit) and 3.5 km/s (from a low-altitude lower-speed orbit), respectively. It is shown that the peak decelerations are an order of magnitude higher for the 5-km/s entries than for the 3.5-km/s entries. The vehicle entering at 3.5 km/s along a gliding trajectory encountered a much more benign atmospheric environment. In addition, the glider's peak deceleration was found to be only about 0.7 earth g, making the shallow flight path ideal for manned vehicles whose crews might be physically weakened by the long voyage to Mars.
Aerodynamic design activities in the Netherlands, which take place mainly at Fokker, the National Aerospace Laboratory (NLR), and Delft University of Technology (TUD), are discussed. The survey concentrates on the development of the Fokker 100 wing, glider design at TUD, and research at NLR in the field of aerodynamic design. Results are shown to illustrate these activities.
Wind tunnel tests were performed on a two-dimensional model of the SM701 airfoil designed for use on the World Class gliders. The test covered a range of Reynolds numbers from 500,000 to 1.7 million. Aerodynamic forces and moments were measured with an external balance. Momentum loss method measurements of the section drag coefficient were also made. Flow visualization techniques provided information on transition from laminar to turbulent flow. Lift, drag, and pitching moment were analyzed and comparisons were made with predicted and previously obtained experimental data. The effects of V-tape turbulators for use in turbulent drag reduction were studied. The performance of a 25 percent chord aileron deflected through plus or minus 20 degrees was researched. The model was designed, constructed, and tested by students at Texas A&M University.
A research effort was undertaken to determine if birds are statically stable in soaring flight and to identify the control method they use for initiating turns. A full-scale radio-controlled glider model of a soaring Raven was successfully developed and flown in a manner which emulates the soaring flight of a bird. It has no vertical stabilizing surfaces and no rudder. The model was air-launched from a 2nd radio-controlled mother ship which allowed consistent and repeatable tests to be performed. Experiments with the model indicate that soaring birds are probably neutrally stable in the pitch axis but seem to soar with positive lateral-directional static stability. The stability source is the spanwise distribution of both dihedral and wing sweep. Simple theoretical equations were developed which roughly predicted the observed Dutch roll period of the model. Experiments also indicate that soaring birds control turns strictly through dihedral effect and the application of a yawing moment to induce sideslip. Successful model flights were completed using up-and-down tail movement for pitch control and tail-tilt for lateral control. The simple baseline Raven model which evolved should provide an excellent starting point for continued research on bird flight.
Explanation of soaring flight. Static and dynamic soaring flight. Results of the Rhon contest. Description of the most important gliders. Notes on Soaring Flight Contests in France and England.
If the low-powered airplane is to be used advantageously by private individuals, the most important consideration is a smaller fuel consumption and, hence, a lower engine power. From experiments with gliders, it appears entirely possible, by utilizing ascending winds (on the weather side of mountains and those generated by the heat of the sun) and by employing engine flight intermittently, as required to fly long distances over land.