Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GLIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1921

Measurements of Rudder Moments on an Airplane During Flight

Tests indicated that: 1) C airplanes with two struts are extremely susceptible to aileron maneuvers, slight alterations of the aileron sufficing to compensate great unequalized moments; 2) great unequalized moments can be produced or neutralized by the unequalized alternation of the angle of attack below the outer and inner struts. Adjustment below the outer strut is the more effective of the two. 3) When a load of bombs is suspended beyond the center of the airplane, below the wings, the bombs need not be dropped simultaneously. 4) The propeller wash of a wide open engine has considerable influence on the position and operation of the elevator. The elevator is more susceptible in flight with the engine running than in gliding flight. 5) Adjustable tail planes are not advisable for D airplanes, nor for the C type, but they are, on the other hand, to be recommended for large size and giant airplanes in which the center of gravity changes during flight. 6) The aileron values obtained by wind tunnel measurements are about 10 percent too low, though otherwise applicable. For the elevator, the results of such measurements should be taken as mean values between flight with the engine running and gliding flight.

Heidelberg, Ing V↗
NASA NTRS1925

Determination of the lift and drag characteristics of an airplane in flight

Flight tests to determine lift and drag characteristics are discussed. A review is given of the fundamental principles on which the tests are based and on the forces acting on an airplane in the various conditions of steady flight. Glide with and without propeller thrust and the relation between angle of attack and the indicated airspeed for different conditions of steady flight are discussed. The glide test procedure and the problem of the propeller are discussed.

Green, Maurice W↗
NASA NTRS1935

Air Conditions Close to the Ground and the Effect on Airplane Landings

This report presents the results of an investigation undertaken to determine the feasibility of making glide landings in gusty air. Wind velocities were measured at several stations between the ground and a height of 51 feet, and flight tests were made to determine the actual influence of gusts on an airplane gliding close to the ground.

Thompson, F L↗
NASA NTRS1958

Low-speed stability and control and spinning characteristics of dynamic models of the X-15 airplane

Paper summarizes the results of low-speed dynamic-model studies of the X-15 aircraft. The investigation included flight tests of a 1/7-scale model in the Langley full-scale tunnel and also in free-gliding flight using a recently developed radio-control technique. In order to interpret and evaluate some of the flight test results, static and dynamic force tests were conducted to determine the low-speed stability and control parameters for angles of attack from 0 degree to as high as 90 degrees. Preliminary tests also have been made in the Langley 20-foot free-spinning tunnel to determine the developed spin and recovery characteristics. Inasmuch as the lower rudder will be jettisoned sometime during the subsonic glide, the investigation has included tests with the lower rudder both on and off.

Hewes, Donald E↗
NASA NTRS1955

A comparative analysis of the performance of long-range hypervelocity vehicles

Long-range hypervelocity vehicles are studied in terms of their motion in powered flight, and their motion and aerodynamic heating in unpowered flight. Powered flight is analyzed for an idealized propulsion system which rather closely approaches present-day rocket motors. Unpowered flight is characterized by a return to earth along a ballistic, skip, or glide trajectory. Only those trajectories are treated which yield the maximum range for a given velocity at the end of powered flight. Aerodynamic heating is treated in a manner similar to that employed previously by the senior authors is studying ballistic missiles (NACA RM A53D28), with the exception that radiant as well as convective heat transfer is considered in connection with glide and skip vehicles. The ballistic vehicle is found to be the least efficient of the several types studied in the sense that it generally requires the highest velocity at the end of powered flight in order to attain a given range. This disadvantage may be offset, however, by reducing convective heat transfer to the re-entry body through the artifice of increasing pressure drag in relation to friction drag - that is, by using a blunt body. Thus the kinetic energy required by the vehicle at the end of powered flight may be reduced by minimizing the mass of coolant material involved.

Eggers, Alfred J , Jr↗
NASA NTRS1934

The effect of weight and drag on the sinking speed and lift/drag ratio of gliders

The most important factors in evaluating performance of gliders are minimum sinking speed and minimum gliding angle. To assure their optimum value the energy necessary for flight, that is, the energy of lift and friction must be kept very low, or in other words, weight and total drag which have a decisive effect on the sinking speed and on the gliding angle, must be kept to a minimum. How great the effect of a reduction of these two quantities will be shown in the following.

Kosin, R↗
NASA NTRS1993

Optical information in landing scenes

During landing, the visual scene contains optical information about speed, altitude, glide slope, and track that is useful for the maintenance of spatial orientation and awareness. This information, embedded in the structure and transformations of the optical patterns, may be globally, regionally, or locally available. Global changes occur everywhere in the visual field during landing and include such information as flow rate acceleration due to changing speed and/or altitude. Regional changes occur within a more restricted area and include such information as horizon line motion due to aircraft pitching and rolling. Locally available changes are the most restricted and include such information as changes in runway form ratios due to changing glide slopes. Thus, within partially or fully synthetic displays, or within sensor-driven displays, preservation of flow rate and horizon motion information requires a minimum of knowledge about the details of the airport layout, while runway outlines do require much more knowledge of the layout. All may be important, however, and these, as well as other sources of optical information, can provide a pilot with his most natural framework for maintaining orientation.

Johnson, Walter W.↗
NASA NTRS1960

Low-Subsonic-Speed Static Longitudinal Stability and Control Characteristics of a Winged Reentry-Vehicle Configuration Having Wingtip Panels that Fold up for High-Drag Reentry

An investigation of the low-subsonic-speed static longitudinal stability and control characteristics of a model of a manned reentry-vehicle configuration capable of high-drag reentry and glide landing has been a made in the Langley free-flight tunnel. The model had a modified 63 deg delta plan-form wing with a fuselage on the upper surface. This configuration had wingtip panels designed to fold up 90 deg for the high-drag reentry phase of the flight and to extend horizontally for the glide landing. Data for the basic configurations and modifications to determine the effects of plan form, wingtip panel incidence, dihedral, and vertical position of the wingtip panels are presented without analysis.

Ware, George M.↗
NASA NTRS1960

Aerodynamic and Landing Measurements Obtained During the First Powered Flight of the North American X-15 Research Airplane

During the first powered flight of the North American X-15 research airplane on September 17, 1959, a Mach number of 2.1 and an altitude of 52,000 feet were attained. Static and dynamic maneuvers were performed to evaluate the characteristics of the airplane at subsonic and supersonic speeds. Data from these maneuvers as well as from the launch and landing phases are presented, discussed, and compared with predicted values. The rate of separation of the X-15 from the B-52 carrier airplane at launch was less than that predicted by wind-tunnel studies and was less rapid than in the lightweight condition of the initial glide flight. In addition, the angular motions and bank angle attained following the launch were of lesser magnitude than in the glide flight. Stable longitudinal-stability trends were apparent during the acceleration to maximum speed, and the pilot reported experiencing little or no transonic trim excursions. An inexplicable high-frequency vibration, which occurred at Mach numbers above 1.4, is being investigated further. Essentially linear lift and stability characteristics were indicated within the limited ranges of angle of attack and angle of sideslip investigated. The dynamic longitudinal and lateral-directional stability and control-effectiveness characteristics appeared satisfactory to the pilot. Although the longitudinal- and lateral-directional-damping ratios showed no significant change from subsonic to supersonic speeds, on the basis of time to damp, the damping characteristics at supersonic speeds appeared to the pilot to be somewhat improved over those at subsonic speeds.

Source record↗
NASA NTRS1998

Flight-Simulated Launch-Pad-Abort-to-Landing Maneuvers for a Lifting Body

The results of an in-flight investigation of the feasibility of conducting a successful landing following a launch-pad abort of a vertically-launched lifting body are presented. The study attempted to duplicate the abort-to-land-ing trajectory from the point of apogee through final flare and included the steep glide and a required high-speed, low-altitude turn to the runway heading. The steep glide was flown by reference to ground-provided guidance. The low-altitude turn was flown visually with a reduced field- of-view duplicating that of the simulated lifting body. Results from the in-flight experiment are shown to agree with ground-based simulation results; however, these tests should not be regarded as a definitive due to performance and control law dissimilarities between the two vehicles.

Jackson, E. Bruce↗
NASA NTRS1946

Free-Spinning Tunnel Tests of a 1/20-Scale Model of the Chance Vought XF6U-1 Airplane, TED No. NACA 2390

A spin investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 1/20-scale model of the Chance Vought XF6U-1 airplane, The effects of control settings and movements upon the erect and inverted spin and recovery characteristics of the model were determined for the normal-fighter condition. The investigation also included tests for the take-off fighter condition (wing-tip tanks plus fuel added) spin-recovery parachutes, and simulated pilot escape. In general, for the normal-fighter condition, the model was extremely oscillatory in roll, pitch, and yaw. The angles of the fuselage varied from extremely flat to inverted attitudes, and the model rotated with the rudder in a series of short turns and glides. Recoveries by rudder reversal were rapid but the model would immediately go into a spin in the other direction. Recoveries by merely neutralizing the rudder were satisfactory when the elevator and ailerons were set to neutral, the ensuing flight path being a steep glide. Thus, it is recommended that all controls be neutralized for safe recovery from spins obtained on the airplane. With the external wing-tip tanks installed, the spins were somewhat less oscillatory in roll but recovery could not be obtained unless full-down elevator was used in conjunction with the rudder. If a spin is entered inadvertently with the full-scale airplane with external wing-tip tanks installed and if recovery is not imminent after a recovery attempt is made, it is recommended that the tanks be jettisoned and the controls neutralized.

Klinar, Walter J.↗
NASA NTRS1948

Measurements of the Lateral and Directional Stability and Control Characteristics of a P-51H Airplane (AAF No. 44-64164)

Flight tests of a P-51H airplane with two different vertical-tail assemblies were made to determine lateral and directional stability and control characteristics. The airplane had satisfactory directional stability in the landing, approach, and wave-off conditions with either tail. In the power-on clean and glide conditions, however, the airplane had weak directional stability with the original tail. The production tail, which had a 7-inch fin extension and a shorter span rudder, improved the directional stability in the power-on clean and glide conditions, but the stability was still weak in the power-on clean condition. Increased altitude in either case caused a slight decrease in the stability. The rudder-trim-force change with speed with either vertical-tail assembly was high. The general aileron control characteristics were satisfactory but the aileron effectiveness failed to meet the Army handling-qualities requirements.

Kraft, Christopher C., Jr.↗
NASA NTRS2009

Apollo-Era Life Rafts Save Hundreds of Sailors

The space shuttle is unique among spacecraft in that it glides back to Earth and lands like an airplane, usually touching ground near where it launched at Kennedy Space Center, but sometimes, in poor weather, gliding into the back-up landing site at Dryden Flight Research Center and then catching a ride back to the Cape on the back of a modified Boeing 747. Before NASA began flying the shuttle, though, astronauts had a longer, more involved trip back to base after a mission. Their capsule, called the command module, would plunge through the atmosphere before releasing a series of parachutes that would slow the craft enough for it to land on the water without too significant of an impact. Called a splashdown, this type of landing put the astronauts out in the ocean, where a specially designated U.S. Navy ship would then deploy a helicopter to retrieve the space travelers. Waiting for the rescue, the astronauts would release a highly visible marker dye into the water, then leave the command module and climb aboard a life raft. These early space pioneers had traveled thousands of miles and then landed safely back on Earth. The journey s end was in sight, but they had one more obstacle. The rotor downdraft from the helicopter coming to retrieve them, reaching sometimes as much as 100 knots per hour, was enough to flip a typical flat-bottomed life raft. Not willing to be thwarted after coming so far, NASA engineers began devising a solution. They knew they needed a highly stable inflatable raft capable of riding out the rough winds, and the solution was to make use of the most abundant resource available: water. Engineers at NASA s Johnson Space Center went to work designing and patenting a hydrodynamically stabilized ballast system that would prevent a life raft from tipping in choppy seas and fierce winds.

Source record↗
NASA NTRS2012

End-To-End Simulation of Launch Vehicle Trajectories Including Stage Separation Dynamics

The development of methodologies, techniques, and tools for analysis and simulation of stage separation dynamics is critically needed for successful design and operation of multistage reusable launch vehicles. As a part of this activity, the Constraint Force Equation (CFE) methodology was developed and implemented in the Program to Optimize Simulated Trajectories II (POST2). The objective of this paper is to demonstrate the capability of POST2/CFE to simulate a complete end-to-end mission. The vehicle configuration selected was the Two-Stage-To-Orbit (TSTO) Langley Glide Back Booster (LGBB) bimese configuration, an in-house concept consisting of a reusable booster and an orbiter having identical outer mold lines. The proximity and isolated aerodynamic databases used for the simulation were assembled using wind-tunnel test data for this vehicle. POST2/CFE simulation results are presented for the entire mission, from lift-off, through stage separation, orbiter ascent to orbit, and booster glide back to the launch site. Additionally, POST2/CFE stage separation simulation results are compared with results from industry standard commercial software used for solving dynamics problems involving multiple bodies connected by joints.

Albertson, Cindy W.↗
NASA NTRS2012

Motion-Base Simulator Evaluation of an Aircraft Using an External Vision System

Twelve air transport-rated pilots participated as subjects in a motion-base simulation experiment to evaluate the use of eXternal Vision Systems (XVS) as enabling technologies for future supersonic aircraft without forward facing windows. Three head-up flight display concepts were evaluated -a monochromatic, collimated Head-up Display (HUD) and a color, non-collimated XVS display with a field-of-view (FOV) equal to and also, one significantly larger than the collimated HUD. Approach, landing, departure, and surface operations were conducted. Additionally, the apparent angle-of-attack (AOA) was varied (high/low) to investigate the vertical field-of-view display requirements and peripheral, side window visibility was experimentally varied. The data showed that lateral approach tracking performance and lateral landing position were excellent regardless of AOA, display FOV, display collimation or whether peripheral cues were present. However, the data showed glide slope approach tracking appears to be affected by display size (i.e., FOV) and collimation. The monochrome, collimated HUD and color, uncollimated XVS with Full FOV display had (statistically equivalent) glide path performance improvements over the XVS with HUD FOV display. Approach path performance results indicated that collimation may not be a requirement for an XVS display if the XVS display is large enough and employs color. Subjective assessments of mental workload and situation awareness also indicated that an uncollimated XVS display may be feasible. Motion cueing appears to have improved localizer tracking and touchdown sink rate across all displays.

Kramer, Lynda J.↗
NASA NTRS2013

Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy: Isothermal Creep - Part I

This two-part paper is the first published report on the long term, low temperature creep of hot-extruded near-stoichiometric NiTi. Constant load tensile creep tests were conducted on hot-extruded near-stoichiometric NiTi at 300, 373 and 473 K under initial applied stresses varying between 200 and 350 MPa as long as 15 months. These temperatures corresponded to the martensitic, two-phase and austenitic phase regions, respectively. Normal primary creep lasting several months was observed under all conditions indicating dislocation activity. Although steady-state creep was not observed under these conditions, the estimated creep rates varied between 10(exp -10) and 10(exp -9)/s. The creep behavior of the two phases showed significant differences. The martensitic phase exhibited a large strain on loading followed by a primary creep region accumulating a small amount of strain over a period of several months. The loading strain was attributed to the detwinning of the martensitic phase whereas the subsequent strain accumulation was attributed to dislocation glide-controlled creep. An "incubation period" was observed before the occurrence of detwinning. In contrast, the austenitic phase exhibited a relatively smaller loading strain followed by a primary creep region, where the creep strain continued to increase over several months. It is concluded that the creep of the austenitic phase occurs by a dislocation glide-controlled creep mechanism as well as by the nucleation and growth of deformation twins.

Raj, S. V.↗
NASA NTRS1933

The Effect of Split Trailing-edge Wing Flaps on the Aerodynamic Characteristics of a Parasol Monoplane

This paper presents the results of tests conducted in the N.A.C.A. full-scale wind tunnel on a Fairchild F-22 airplane equipped with a special wing having split trailing-edge flaps. The flaps extended over the outer 90 percent of the wing span, and were of the fixed-hinge type having a width equal to 20 percent of the wing chord. The results show that with a flap setting of 59 degrees the maximum lift of the wing was increased 42 percent, and that the flaps increased the range of available gliding angles from 2.7 degrees to 7.0 degrees. Deflection of the split flaps did not increase the stalling angle or seriously affect the longitudinal balance of the airplane. With flaps down the landing speed of the airplane is decreased, but the calculated climb and level-flight performance is inferior to that with the normal wing. Calculations indicate that the take-off distance required to clear an obstacle 100 feet high is not affected by flap settings from 0 degrees to 20 degrees but is greatly increased by larger flap angles.

TAKE-OFF & LANDING - EFFECT OF WING FLAPS↗