Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Force Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Unveiling the mechanism of surface corrugation formation on a quasi free-standing bi-layer graphene via experimental and modeling investigations

Extensive studies have been conducted to accomplish the controls over the formation of surface corrugations on chemical vapor deposited (CVD) graphene. However, the underlying mechanism of the surface corrugation formation on graphene remains elusive, due to the difficulty delineating the growth-induced surface corrugations from wrinkles formed during graphene transfer with the use of a supporting layer casted on top of the sample. Here, in this study, “quasi free-standing” graphene was realized using the weakly-interacting h-BN layer during a wet transfer process to study the surface corrugation formation on graphene. The weak interaction of graphene with the supporting h-BN layer allows for the growth-induced surface corrugations to be released, enabling the investigation of the primary mechanism for the graphene corrugation behavior during the transfer process. The experimental measurements of surface corrugations were conducted using atomic force microscopy (AFM) to reveal that surface corrugations are formed following the graphene’s crystallographic directions. Density functional theory calculations using the projector augmented-wave (PAW) method and Perdew-Burke-Ernzerhof (PBE) exchange correlation functional were also conducted for two models of “atomic-scale ripples” and “nanoscale wrinkles” and showed that all of them are formed along the crystallographic axis of graphene, which is in good agreement with the experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Quantitatively controlled electrophoretic deposition of nanocrystal films from non-aqueous suspensions

This study presents a novel method to correlate the mass and charge transfer kinetics during the electrophoretic deposition of nanocrystal films by using a purpose-built double quartz crystal microbalance combined with simultaneous current-measurement. Our data support a multistep process for film formation: generation of charged nanocrystal flux, charge transfer at the electrode, and polarization of neutral nanocrystals near the electrode surface. The polarized particles are then subject to dielectrophoretic forces that reduce diffusion away from the interface, generating a sufficiently high neutral particle concentration at the interface to form a film. The correlation of mass and charge transfer enables quantification of the nanocrystal charge, the fraction of charged nanocrystals, and the initial sticking coefficient of the particles. These quantities permit calculation of the film thickness, providing a theoretical basis for using concentration and voltage as process parameters to grow films of targeted thicknesses.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Magnetically driven coupling in relativistic radiation-mediated shocks

ABSTRACT The radiation drag in photon-rich environments of cosmic explosions can seed kinetic instabilities by inducing velocity spreads between relativistically streaming plasma components. Such microturbulence is likely imprinted on the breakout signals of radiation-mediated shocks. However, large-scale, transverse magnetic fields in the deceleration region of the shock transition can suppress the dominant kinetic instabilities by preventing the development of velocity separations between electron–positron pairs and a heavy ion species. We use a 1D five-fluid radiative transfer code to generate self-consistent profiles of the radiation drag force and plasma composition in the deceleration region. For increasing magnetization, our models predict rapidly growing pair multiplicities and a substantial radiative drag developing self-similarly throughout the deceleration region. We extract the critical magnetization parameter σc, determining the limiting magnetic field strength at which a three-species plasma can develop kinetic instabilities before reaching the isotropized downstream. For a relativistic, single ion plasma drifting with γu = 10 in the upstream of a relativistic radiation-mediated shock, we find the threshold σc ≈ 10−7 for the onset of microturbulence. Suppression of plasma instabilities in the case of multi-ion composition would likely require much higher values of σc. Identifying high-energy signatures of microturbulence in shock breakout signals and combining them with the magnetization limits provided in this work will allow a deeper understanding of the magnetic environment of cosmic explosions like supernovae, gamma-ray bursts, and neutron star binary mergers.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Facile fabrication of 2D material multilayers and vdW heterostructures with multimodal microscopy and AFM characterization

Reliable transfer processes that enable manipulation of two-dimensional (2D) materials, e.g., transition metal dichalcogenides (TMDCs) and MXenes, from one substrate to another has been a necessity for successful device fabrication. Here, with both mechanical exfoliation and chemical vapor deposition (CVD) widely used, a versatile, clean, deterministic, and yet simple transfer technique is highly needed. To address such need, we developed a transfer method that takes advantage of wettability contrast between interfaces without the use of sacrificial layers or chemical processes. More importantly, a setup was developed to carry out this transfer method with high sample selectivity and fine control of the position and orientation of transferred TMDC crystals, a feature required for fabrication of the devices based on vertical 2D heterostructures. Using both exfoliated and CVD grown materials and subsequent atomic force microscopy (AFM), photoluminescence (PL), confocal Raman and tip enhanced Raman spectroscopy (TERS) characterization, we ascertained the quality of interfaces resulting from the transfer process while preserving excellent 2D material integrity. PL and TERS maps revealed nanometer-scale heterogeneities in the interfaces of fabricated heterostructures, which should enable further perfection of the transfer technique. TERS/TEPL information were employed to identify areas suitable for nanodevice fabrication, making the reported transfer and characterization methods ideal for making high quality assembly of 2D heterostructure more accessible, which should facilitate exploration of vertical 2D heterostructures for applications in electronics, batteries, solar cells, and twistronics.

2D material transfer↗
DOE OSTI2025

Improved Treatment of 1–4 Interactions in Force Fields for Molecular Dynamics Simulations

Traditional force fields commonly use a combination of bonded torsional terms and empirically scaled nonbonded interactions to capture 1-4 energies and forces of atoms separated by three bonds in a molecule. While this approach can yield accurate torsional energy barriers, it often leads to inaccurate forces and erroneous geometries and creates an interdependence between dihedral terms and nonbonded interactions, complicating parametrization and reducing transferability. Here, in this paper, we demonstrate that 1-4 interactions can be accurately modeled using only bonded coupling terms, eliminating the need for arbitrarily scaled nonbonded interactions altogether. Furthermore, by leveraging the automated parametrization capabilities of the Q-Force toolkit, we efficiently determine the necessary coupling terms without the need for manual adjustment. Our approach is first validated on a range of small molecule systems, encompassing both flexible and rigid structures, and shows a significant improvement in force field accuracy, obtaining subkcal/mol mean absolute error for every molecule tested. We further extend the bonded-only model for 1-4 interactions to Amber ff14sb, CHARMM36, and OPLS-AA force fields to reproduce ab initio gas and implicit solvent ϕ,ψ surfaces of alanine dipeptide.

Abdullah, Aalim S. [University of California, Berk↗
DOE OSTI2021

Recurrence analysis of friction based dry-couplant ultrasonic Lamb waves in plate-like structures

Here, in this study, the effect of friction on the generation of dry-coupled Lamb waves is experimentally investigated. Recurrence analysis is performed to analyze the complex behavior of friction based dry-coupled Lamb waves. In particular, the effect of the normal force, which is necessary for a stronger dry-coupled Lamb wave generation and the friction, on the transmission of mechanical energy and determinism characteristics of Lamb waves are investigated. The results verify that larger friction coefficient and friction force are crucial for generation and propagation of strong Lamb waves supporting the fact that the main mechanism to transfer mechanical energy using dry-couplant is friction. The sensitivity of Lamb waves to the friction coefficient, highlights the importance of designing specific pads with respect to condition of the surface. Besides, the results show that the normal force and friction coefficient can change the determinism characteristics behavior of multimode Lamb waves. Furthermore, it is shown that the determinism value is sensitive to the friction coefficient and normal force. A similar trend is observed in the determinism values and friction coefficient. In general, a smaller friction coefficient indicates smaller determinism value. Additionally, it is shown that a normal load can change the behavior of a system, as observed from recurrence plots, owing to changes in the Lamb waves trajectories in the phase-space domain. In addition, it is shown that recurrence plots enable the detection of mode transitions in multimode Lamb waves. Recurrence analysis is a complementary tool to frequency domain methods for accurate analysis of multimode Lamb waves behavior.

42 ENGINEERING↗
DOE OSTI2023

Heat transfer enhancement due to cold cap motion from bubbling in a waste glass melter

In this study, a computational fluid dynamics (CFD) model was developed to model the motion of a solid cold cap in a waste glass melter. Forced convection bubblers at the base of the melter release air into the molten glass, which forms large bubbles that travel upwards to the cold cap and augment heat transfer from the glass to the cold cap. The CFD model employs the Navier- Stokes equations to solve for the fluctuating flowfield using a rigid body motion dynamic fluid body interaction module. This allows for movement of the floating body in response to the bubbling forces calculated at each time step. Further, the heat flux delivered to the cold cap by the convective bubbling is studied as a function of the bubbling rate. Results for the moving cold cap are compared with the computed heat flux trends for a stationary cold cap. The heat flux delivered to the cold cap from the glass is 25% higher for the case with the moving cold cap. The heat flux was found to be proportional to v0.6 as opposed to v0.9 (where v is the normalized bubbling rate) for the stationary cold cap.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Statistical Analysis of the Limiting Dynamics of Two dimensional Boussinesq Turbulent Systems

In the current study, we investigate rotational and stratified turbulent systems within the framework of the Boussinesq equations. The effects of rotation and stratification give rise to a variety of dynamical regimes in atmospheric and oceanic turbulence. To develop a better understanding of the fundamental flow properties through a more straightforward mathematical framework, we commence our research with a simplified two-dimensional Boussinesq model that incorporates rotation and stratification effects. We explore two distinct limiting dynamics, considering pure rotation and pure stratification separately. We examine these intriguing dynamics through numerical investigations, applying the exact solution theory of Boussinesq equations and examining small-scale perturbations to the exact solution under rotation and stratification. We conduct an analysis of statistical quantities associated with the turbulent state variables. The results indicate that, under weak rotation at the equilibrium statistical state, the flow field exhibits vortex flow. However, strong rotation transforms the flow into vertical shear flow. We observe both downscale and upscale energy transfers with a decay rate of k −3 in the absence of external forcing and dissipation. Furthermore, we delve into the study of internal gravity wave mode interactions in the simplified two-dimensional Boussinesq system, which is a crucial aspect of geophysical turbulence due to gravity. Our findings reveal that the time series of the mode coefficients exhibit wave-like interactions between wave modes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Light-Dependent Impedance Spectra and Transient Photoconductivity in a Ruddlesden–Popper 2D Lead–Halide Perovskite Revealed by Electrical Scanned Probe Microscopy and Accompanying Theory

Electric force microscopy was used to record the light-dependent impedance spectrum and the probe transient photoconductivity of a film of butylammonium lead iodide, BA 2 PbI 4 , a 2D Ruddlesden–Popper perovskite semiconductor. The impedance spectrum of BA 2 PbI 4 showed modest changes as the illumination intensity was varied up to 1400 mW cm –2 , in contrast with the comparatively dramatic changes seen for 3D lead–halide perovskites under similar conditions. BA 2 PbI 4 ’s light-induced conductivity had a rise time and decay time of ~100 μs, 10 4 slower than expected from direct electron–hole recombination yet 10 5 faster than the conductivity-recovery times recently observed in 3D lead–halide perovskites and attributed to the relaxation of photogenerated vacancies. What sample properties are probed by electric force microscope measurements remains an open question. A Lagrangian-mechanics treatment of the electric force microscope experiment was recently introduced by Dwyer, Harrell, and Marohn which enabled the calculation of steady-state electric force microscope signals in terms of a complex sample impedance. Here this impedance treatment of the tip–sample interaction is extended, through the introduction of a time-dependent transfer function, to include time-resolved electrical scanned probe measurements. Here, it is shown that the signal in a phase-kick electric force microscope experiment, and therefore also the signal in a time-resolved electrostatic force microscope experiment, can be written explicitly in terms of the sample’s time-dependent resistance (i.e., conductivity).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Electro-optic transduction in silicon via gigahertz-frequency nanomechanics

Interfacing electronics with optical fiber networks is key to the long-distance transfer of classical and quantum information. Piezo-optomechanical transducers enable such interfaces by using gigahertz-frequency acoustic vibrations as mediators for converting microwave photons to optical photons via the combination of optomechanical and piezoelectric interactions. However, despite successful demonstrations, efficient quantum transduction remains out of reach due to the challenges associated with hybrid material integration and increased loss from piezoelectric materials when operating in the quantum regime. Here, we demonstrate an alternative approach in which we actuate 5-GHz phonons in a conventional silicon-on-insulator platform. In our experiment, microwave photons resonantly drive a phononic crystal oscillator via the electrostatic force realized in a charge-biased narrow-gap capacitor. The mechanical vibrations are subsequently transferred via a phonon waveguide to an optomechanical cavity, where they transform into optical photons in the sideband of a pump laser field. Operating at room temperature and atmospheric pressure, we measure a microwave-to-optical photon conversion efficiency of 1.72±0.14×10 −7 in a 3.3 MHz bandwidth. Our results mark a stepping stone towards quantum transduction with integrated devices made from crystalline silicon, which promise efficient high-bandwidth operation and integration with superconducting qubits. Additionally, the lack of need for piezoelectricity or other intrinsic nonlinearities makes our approach applicable to a wide range of materials for potential applications beyond quantum technologies.

42 ENGINEERING↗
DOE OSTI2024

Quasi-Classical Trajectory Calculation of Rate Constants Using an Ab Initio Trained Machine Learning Model (aML-MD) with Multifidelity Data

Machine learning (ML) provides a great opportunity for the construction of models with improved accuracy in classical molecular dynamics (MD). However, the accuracy of a ML trained model is limited by the quality and quantity of the training data. Generating large sets of accurate ab initio training data can require significant computational resources. Furthermore, inconsistent or incompatible data with different accuracies obtained using different methods may lead to biased or unreliable ML models that do not accurately represent the underlying physics. Recently, transfer learning showed its potential for avoiding these problems as well as for improving the accuracy, efficiency, and generalization of ML models using multifidelity data. In this work, ab initio trained ML-based MD (aML-MD) models are developed through transfer learning using DFT and multireference data from multiple sources with varying accuracy within the Deep Potential MD framework. Further, the accuracy of the force field is demonstrated by calculating rate constants for the H + HO 2 → H 2 + 3 O 2 reaction using quasi-classical trajectories. We show that the aML-MD model with transfer learning can accurately predict the rate constants while reducing the computational cost by more than five times compared to the use of more expensive quantum chemistry training data sets. Hence, the aML-MD model with transfer learning shows great potential in using multifidelity data to reduce the computational cost involved in generating the training set for these potentials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Constitutional under-potential plating (CUP) – New insights for predicting the morphological stability of deposited lithium anodes in lithium metal batteries

Lithium (Li) cycling in lithium metal batteries (LMBs) inevitably witnesses a non-planar Li/electrolyte interface (cellular/dendritic microstructure) affecting the performance, safety and reliability of LMBs. Herein, the “constitutional under-potential plating” (CUP) concept is presented for the first time to understand the evolution, formation and predict the morphological stability/instability of the Li/electrolyte interface. Here, the CUP condition, a measure of the driving force for interface perturbation, occurs when the true potential gradient at the interface is smaller than the equilibrium electrodeposition potential gradient at the Li/electrolyte interface resulting in the electrolyte ahead of the Li-electrolyte interface to be in an under-potential state. Detailed CUP criterion calculations conducted herein establishes the relationship of battery operating conditions (e.g. current density, potential gradient) with the electrolyte properties (e.g. Li-ion transference number and diffusion coefficient) predicting the morphological stability condition at the interface. In addition to the driving force for interface perturbation, the capillarity effect or the Gibbs Thomson effect, a measure of the resistance to perturbation of the perturbed interface is discussed for understanding the influence of interfacial energy/adhesion energy between the current collector and the deposited Li on the overall morphological stability of the Li/electrolyte interface, a critical criterion for the unwanted dendritic morphology.

25 ENERGY STORAGE↗
DOE OSTI2020

Hypothetical Efficiency of Electrical to Mechanical Energy Transfer during Individual Stochastic Molecular Switching Events

There are now many examples of single molecule rotors, motors and switches in the literature that, when driven by photons, electrons or chemical reactions, exhibit well defined motions. As a step towards using these single molecule devices to perform useful functions one must understand how they interact with their environment and quantify their ability to perform work on it. Using a single molecule rotary switch we examine the transfer of electrical energy, delivered via electron tunneling, to mechanical motion and measure the forces the switch experiences with a non-contact q-plus atomic force microscope. Action spectra reveal that the molecular switch has two stable states and can be excited resonantly between them at a bias of 100 mV via a one-electron inelastic tunneling process which corresponds to an energy input of 16 zepto Joules. Furthermore, while the electrically induced switching events are stochastic and no net work is to done on the cantilever, by measuring the forces between the molecular switch and the AFM cantilever we can derive the maximum hypothetical work the switch could perform during a single switching event which is ~55 meV, equal to 8.9 zepto Joules which translates to a hypothetical efficiency ~55% per individual inelastic tunneling electron induced switching event. When co considering the total electrical energy input this drops to 1x10 -7 % due to elastic tunneling events that dominate the tunneling current. However, this approach constitutes a general method for quantifying and comparing the energy input and output of molecularmechanical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chiral induction at the nanoscale and spin selectivity in electron transmission in chiral methylated BEDT-TTF derivatives

Great efforts have been made in the last few decades to realize electronic devices based on organic molecules. A possible approach in this field is to exploit the chirality of organic molecules for the development of spintronic devices, an applicative way to implement the chiral-induced spin selectivity (CISS) effect. In this work we exploit enantiopure tetrathiafulvalene (TTF) derivatives as chiral inducers at the nanoscale. The aim is to make use of TTF's well-known and unique semiconducting properties, to be expressed in the fields of enantio-selectivity and the chiral-induced spin selectivity (CISS) effect. Further, the experimental results shown in this paper further demonstrate how chirality and spin are deeply interrelated, as foreseen within the CISS effect theory, paving the way for the application of TTF derivatives in the field of spintronics. In this work, we demonstrate that tetramethyl-bis(ethylenedithio)-tetrathiafulvalene (TM-BEDT-TTF) (1) behaves as an efficient spin filter, as evidenced by magneto-atomic force microscopy (mc-AFM) measurements. Additionally, it is shown to be effective in transferring chirality to CdS/CdSe core–shell nanoparticles, as inferred from the analysis of circularly resolved photoluminescence spectra. This makes 1 a promising candidate for a variety of applications, ranging from plasmonics to quantum computing.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Dynamic control of the spatial frequency content of an intense laser via intra-beam energy transfer

We present theory and simulations demonstrating that bandwidth-inducing optical smoothing techniques such as smoothing by spectral dispersion (SSD) can initiate intra-beam energy transfer (IBET) within a single beam. IBET consists of energy transfer between the different frequency components of the beam and results in a simultaneous and correlated redistribution of the temporal and spatial frequencies of the laser's electric field. We identify a threshold in bandwidth for IBET to occur and validate the theory with simulations. The bandwidth and the color cycling of SSD can result in IBET in conditions relevant for high-energy density experiments at the National Ignition Facility and Omega Laser. We show that IBET could be used to manipulate a laser's spatial frequency content within a plasma. In particular, this technique could be used to increase a laser's effective f-number, with potential applications for self-guiding in plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Pulsed laser induced atomic layer etching of silicon

Here, we demonstrate the laser mediated atomic layer etching (ALEt) of silicon. Using a nanosecond pulsed 266 nm laser focused loosely over and in a parallel configuration to the surface of the silicon, we dissociate Cl 2 gas to induce chlorination. Then, we use pulsed picosecond irradiation to remove the chlorinated layer. Subsequently, we perform continuous wave (CW) laser annealing to eliminate amorphization caused by the picosecond laser etching. Based on atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS), we observed strong evidence of chlorination and digital etching at 0.85 nm etching per cycle with good uniformity.

42 ENGINEERING↗
DOE OSTI2020

Heat Generation versus Heat Dissipation Maps for Batteries (Battery Safety Maps) [SWR-21-27]

NREL's Battery Safety Map (Heat Generation versus Heat Dissipation Maps for Batteries) generates a response surface that is grouped into regions where the battery is deemed safe from the propagation of thermal runaway, those where an engineering solution would render the battery safe, and finally instances where thermal runaway is inevitable. The demarcation for the different regions is provided by specifications or constraints imposed by the end user. NREL's Battery Safety Map is a user-defined subroutine that sweeps through a set of parameters describing the operating conditions and short-circuit scenarios for battery safety simulations. For each run, the electrochemical-thermal model implementing reaction kinetics and gas generation are run to evaluate the amount of heat generated. A thermal model then captures the amount of heat dissipation based on boundary conditions defined (e.g., forced convection, constant temperature at the surface, etc.). Based on the rate of heat transfer and the amount of heat generated, each run is classified into "safe," "mitigation possible," or "unsafe" zones. These categories are defined based on constraints or tolerance specifications provided by the end user.

Santhanagopalan, Shriram↗