Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flow Conditions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Research on Supersonic Inlet Bleed

Phase I data results of the Fundamental Inlet Bleed Experiments project at NASA Glenn Research Center (GRC) are presented which include flow coefficient results for two single-hole boundary-layer bleed configurations. The bleed configurations tested are round holes at inclination angles of 90deg and 20deg both having length-to-diameter ratios of 2.0. Results were obtained at freestream Mach numbers of 1.33, 1.62, 1.98, 2.46, and 2.92 and unit Reynolds numbers of 0.984, 1.89, and 2.46 10(exp 7)/m. Approach boundary-layer data are presented for each flow condition and the flow coefficient results are compared to existing multi-hole data obtained under similar conditions. For the 90deg hole, the single and multi-hole distributions agree fairly well with the exception that under supercritical operation, the multi-hole data chokes at higher flow coefficient levels. This behavior is also observed for the 20deg hole but to a lesser extent. The 20deg hole also shows a markedly different characteristic at subcritical operation. Also presented are preliminary results of a Computational Fluid Dynamics (CFD) analysis of both configurations at the Mach 1.33 and a unit Reynolds number of 2.46 10(exp 7)/m. Comparison of the results shows the agreement to be very good.

Davis, David O.↗
NASA NTRS1975

Analytic and experimental evaluation of flowing air test conditions for selected metallics in a shuttle TPS application

A detailed experimental and analytical evaluation was performed to define the response of TD nickel chromium alloy (20 percent chromium) and coated columbium (R512E on CB-752 and VH-109 on WC129Y) to shuttle orbiter reentry heating. Flight conditions important to the response of these thermal protection system (TPS) materials were calculated, and test conditions appropriate to simulation of these flight conditions in flowing air ground test facilities were defined. The response characteristics of these metallics were then evaluated for the flight and representative ground test conditions by analytical techniques employing appropriate thermochemical and thermal response computer codes and by experimental techniques employing an arc heater flowing air test facility and flat face stagnation point and wedge test models. These results were analyzed to define the ground test requirements to obtain valid TPS response characteristics for application to flight. For both material types in the range of conditions appropriate to the shuttle application, the surface thermochemical response resulted in a small rate of change of mass and a negligible energy contribution. The thermal response in terms of surface temperature was controlled by the net heat flux to the surface; this net flux was influenced significantly by the surface catalycity and surface emissivity. The surface catalycity must be accounted for in defining simulation test conditions so that proper heat flux levels to, and therefore surface temperatures of, the test samples are achieved.

Schaefer, J. W.↗
NASA NTRS1993

DSMC simulations of Mach 20 nitrogen flows about a 70 degree blunted cone and its wake

Numerical results obtained with the direct simulation Monte Carlo (DSMC) method are presented for Mach 20 nitrogen flow about a 70-deg blunted cone. The flow conditions simulated are those that can be obtained in existing low-density hypersonic wind tunnels. Three sets of flow conditions are simulated with freestream Knudsen numbers ranging from 0.03 to 0.001. The focus is to characterize the wake flow under rarefied conditions. This is accomplished by calculating the influence of rarefaction on wake structure along with the impact that an afterbody has on flow features. This data report presents extensive information concerning flowfield features and surface quantities.

Moss, James N.↗
NASA NTRS1979

Similitude requirements and scaling relationships as applied to model testing

The similitude requirements for the most general test conditions are presented. These similitude requirements are considered in relation to the scaling relationships, test technique, test conditions (including supersonic flow), and test objectives. Particular emphasis is placed on satisfying the various similitude requirements for incompressible and compressible flow conditions. For free flying models tests, the test velocities for incompressible flow are scaled from Froude number similitude requirements and those for compressible flow are scaled from Mach number similitude requirements. The limitations of various test techniques are indicated, with emphasis on the free flying model.

Wolowicz, C. H.↗
NASA NTRS1991

Review of boundary layer transition flight data on the Space Shuttle Orbiter

Both thermocouple data and flight-derived axial force coefficients have been used to determine the freestream flight conditions at which boundary-layer transition occurs on the windward surface of the Space Shuttle Orbiter during reentry. Boundary-layer-edge local flow conditions corresponding to transition at thermocouple locations on the Orbiter windward centerline have also been computed. Tables of the freestream conditions and the local flow conditions at transition are included. Transition occurred over a freestream Mach number range of 6.6 to 17.9 and Reynolds number range of (2.3-9.6) x 10 to the 6th. The roughness state of the Orbiter vehicles is also discussed and correlated to the occurrence of transition. Using the distributed roughness transition correlation of Bertin et al. (1982), a flight-derived roughness height of 0.061 inches was obtained. An average flight-derived roughness height of 0.103 inches for a discrete roughness element in the nose region was obtained using the correlation of Van Driest and Blumer (1968).

Bouslog, S. A.↗
NASA NTRS2009

Simulation of RCC Crack Growth Due to Carbon Oxidation in High-Temperature Gas Environments

The carbon wall oxidation technique coupled with a CFD technique was employed to study the flow in the expanding crack channel caused by the oxidation of the channel carbon walls. The recessing 3D surface morphing procedure was developed and tested in comparison with the arcjet experimental results. The multi-block structured adaptive meshing was used to model the computational domain changes due to the wall recession. Wall regression rates for a reinforced carbon-carbon (RCC) samples, that were tested in a high enthalpy arcjet environment, were computationally obtained and used to assess the channel expansion. The test geometry and flow conditions render the flow regime as the transitional to continuum, therefore Navier-Stokes gas dynamic approach with the temperature jump and velocity slip correction to the boundary conditions was used. The modeled mechanism for wall material loss was atomic oxygen reaction with bare carbon. The predicted channel growth was found to agree with arcjet observations. Local gas flow field results were found to affect the oxidation rate in a manner that cannot be predicted by previous mass loss correlations. The method holds promise for future modeling of materials gas-dynamic interactions for hypersonic flight.

Titov, E. V.↗
NASA NTRS1973

Analytical study of pressure balancing in gas film seals.

Proper pressure balancing of gas film seals requires knowledge of the pressure profile load factor (load factor) values for a given set of design conditions. In this study, the load factor is investigated for subsonic and choked flow conditions, laminar and turbulent flows, and various seal entrance conditions. Both parallel sealing surfaces and surfaces with small linear deformation were investigated. The load factor for subsonic flow depends strongly on pressure ratio; under choked flow conditions, however, the load factor is found to depend more strongly on film thickness and flow entrance conditions rather than pressure ratio. The importance of generating hydrodynamic forces to keep the seal balanced under severe and multipoint operation is also discussed.

Zuk, J.↗
NASA NTRS2004

Performance of Thermal Mass Flow Meters in a Variable Gravitational Environment

The performance of five thermal mass flow meters, MKS Instruments 179A and 258C, Unit Instruments UFM-8100, Sierra Instruments 830L, and Hastings Instruments HFM-200, were tested on the KC-135 Reduced Gravity Aircraft in orthogonal, coparallel, and counterparallel orientations relative to gravity. Data was taken throughout the parabolic trajectory where the g-level varied from 0.01 to 1.8 times normal gravity. Each meter was calibrated in normal gravity in the orthogonal position prior to flight followed by ground testing at seven different flow conditions to establish a baseline operation. During the tests, the actual flow rate was measured independently using choked-flow orifices. Gravitational acceleration and attitude had a unique effect on the performance of each meter. All meters operated within acceptable limits at all gravity levels in the calibrated orthogonal position. However, when operated in other orientations, the deviations from the reference flow became substantial for several of the flow meters. Data analysis indicated that the greatest source of error was the effect of orientation, followed by the gravity level. This work emphasized that when operating thermal flow meters in a variable gravity environment, it is critical to orient the meter in the same direction relative to gravity in which it was calibrated. Unfortunately, there was no test in normal gravity that could predict the performance of a meter in reduced gravity. When operating in reduced gravity, all meters indicated within 5 percent of the full scale reading at all flow conditions and orientations.

Brooker, John E.↗
NASA NTRS2017

Jet-Surface Interaction Noise from High-Aspect Ratio Nozzles: Test Summary

Noise and flow data have been acquired for a 16:1 aspect ratio rectangular nozzle exhausting near a simple surface at the NASA Glenn Research Center as part of an ongoing effort to understand, model, and predict the noise produced by current and future concept aircraft employing a tightly integrated engine airframe designs. The particular concept under consideration in this experiment is a blended-wing-body airframe powered by a series of electric fans exhausting through slot nozzle over an aft deck. The exhaust Mach number and surface length were parametrically varied during the test. Far-field noise data were acquired for all nozzle surface geometries and exhaust flow conditions. Phased-array noise source localization data and in-flow pressure data were also acquired for a subset of the isolated (no surface) and surface configurations; these measurements provide data that have proven useful for modeling the jet-surface interaction noise source and the surface effect on the jet-mixing noise in round jets. A summary of the nozzle surface geometry, flow conditions tested, and data collected are presented.

Propulsion Noise↗
NASA NTRS2018

Heat Transfer Measurements on the Endwall of a Variable Speed Power Turbine Blade Cascade

Heat transfer measurements were obtained on the endwall of a 2-D section of a variable speed power turbine (VSPT) rotor blade linear cascade. Infrared thermography was used to help determine the transition of flow from laminar to turbulent as well as determine regions of flow separation. Steady state data was obtained for six incidence angles ranging from +15.8 deg to -51 deg, and at five flow conditions for each angle. Nusselt number was used as a method to visualize flow transition and separation on the endwall surface and showed the effects of secondary flows on the surface. Nusselt correlation with Reynolds number from multiple flow conditions was used to plot local values of the correlation exponent and indicated the state of the local boundary layer as the flow transitioned from laminar to turbulent as well as secondary flow features.

variable speed power turbine↗
NASA NTRS1994

Navier-Stokes, flight, and wind tunnel flow analysis for the F/A-18 aircraft

Computational analysis of flow over the F/A-18 aircraft is presented along with complementary data from both flight and wind tunnel experiments. The computational results are based on the three-dimensional thin-layer Navier-Stokes formulation and are obtained from an accurate surface representation of the fuselage, leading-edge extension (LEX), and the wing geometry. However, the constraints imposed by either the flow solver and/or the complexity associated with the flow-field grid generation required certain geometrical approximations to be implemented in the present numerical model. In particular, such constraints inspired the removal of the empennage and the blocking (fairing) of the inlet face. The results are computed for three different free-stream flow conditions and compared with flight test data of surface pressure coefficients, surface tuft flow, and off-surface vortical flow characteristics that included breakdown phenomena. Excellent surface pressure coefficient correlations, both in terms of magnitude and overall trend, are obtained on the forebody throughout the range of flow conditions. Reasonable pressure agreement was obtained over the LEX; the general correlation tends to improve at higher angles of attack. The surface tuft flow and the off-surface vortex flow structures compared qualitatively well with the flight test results. To evaluate the computational results, a wind tunnel investigation was conducted to determine the effects of existing configurational differences between the flight vehicle and the numerical model on aerodynamic characteristics. In most cases, the geometrical approximations made to the numerical model had very little effect on overall aerodynamic characteristics.

Ghaffari, Farhad↗
NASA NTRS1994

Calibration of Axisymmetric and Quasi-1D Solvers for High Enthalpy Nozzles

The proposed paper will present a numerical investigation of the flow characteristics and boundary layer development in the nozzles of high enthalpy shock tunnel facilities used for hypersonic propulsion testing. The computed flow will be validated against existing experimental data. Pitot pressure data obtained at the entrance of the test cabin will be used to validate the numerical simulations. It is necessary to accurately model the facility nozzles in order to characterize the test article flow conditions. Initially the axisymmetric nozzle flow will be computed using a Navier Stokes solver for a range of reservoir conditions. The calculated solutions will be compared and calibrated against available experimental data from the DLR HEG piston-driven shock tunnel and the 16-inch shock tunnel at NASA Ames Research Center. The Reynolds number is assumed to be high enough at the throat that the boundary layer flow is assumed turbulent at this point downstream. The real gas affects will be examined. In high Mach number facilities the boundary layer is thick. Attempts will be made to correlate the boundary layer displacement thickness. The displacement thickness correlation will be used to calibrate the quasi-1D codes NENZF and LSENS in order to provide fast and efficient tools of characterizing the facility nozzles. The calibrated quasi-1D codes will be implemented to study the effects of chemistry and the flow condition variations at the test section due to small variations in the driver gas conditions.

Papadopoulos, P. E.↗
NASA NTRS1956

Friction factors for flow of non-newtonian materials in pipelines

In many industries, non-Newtonian material, such as oils, lubricants, foods, cosmetics, and solid-liquid suspensions, are passed through pipelines during manufacture, application, or transportation. For the proper design of the pipelines, and evaluation of the flow resistance of the materials when flowing in these pipelines is essential. The pressure loss Δ p , due to a material flowing through a straight pipeline can be expressed as a function of a friction factor, φ, so that Δ p = ( pv 2 )/2 L/D φ where φ is a function of the flow properties of the material v is the mean velocity of the material and can be determined from the mas-flow rate, L is the length and D is the diameters of the pipeline, and p is the density of the material. The purpose of this paper is to present a generalized friction diagram, which can be used to determine φ for any material and flow condition, provided the flow properties of the material and the mean flow velocity in the pipeline are known. In composing this diagram generous use is made of the literature and only parts of the diagram and the presentation can claim originality.

Ruth N Weltmann↗
NASA NTRS1972

Experimental investigation of two-phase heat transfer in a porous matrix.

One-dimensional two-phase flow transpiration cooling through porous metal is studied experimentally. The experimental data is compared with a previous one-dimensional analysis. Good agreement with calculated temperature distribution is obtained as long as the basic assumptions of the analytical model are satisfied. Deviations from the basic assumptions are caused by nonhomogeneous and oscillating flow conditions. Preliminary derivation of nondimensional parameters which characterize the stable and unstable flow conditions is given. Superheated liquid droplets observed sputtering from the heated surface indicated incomplete evaporation at heat fluxes well in access of the latent energy transport. A parameter is developed to account for the nonequilibrium thermodynamic effects. Measured and calculated pressure drops show contradicting trends which are attributed to capillary forces.

Von Reth, R.↗
NASA NTRS1985

A sensitivity analysis of the Shuttle Orbiter heating

A procedure for estimating relative sensitivities in Space Shuttle Orbiter entry heating due to variations from nominal flight parameters is presented. Ballpark values are provided for assessing heating changes caused by off-nominal variations in anglle of attack and Reynolds number for laminar flow conditions. Also, a procedure for scaling heating data obtained on subscale models tested at low-enthalpy wind-tunnel test conditions to high-enthalpy flight conditions using simplified flow analysis techniques is presented and verified with flight and wind-tunnel data. In addition, data are presented illustrating that a significant increase in heating was experienced on the fifth Orbiter flight. The increase was possibly caused by changes in the catalytic properties of the Orbiter thermal protection system surface.

Williams, S. D.↗
NASA NTRS1990

A unified Navier-Stokes flowfield and performance analysis of liquid rocket engines

To improve the current composite solutions in the design and analysis of liquid propulsive engines, a computational fluid dynamics model capable of calculating the nonreacting and reacting flows from the combustion chamber, through the nozzle to the external plume, was developed. The Space Shuttle Main Engine (SSME) fired at sea level, along with the flowfields of several other nozzles were investigated. The bell-shaped SSME nozzle was run at 100 percent power level at various flow conditions, the computed flow results and performance compared well with those of other standard codes and engine hot fire test data.

Wang, Ten-See↗
NASA NTRS1991

Mach 3.5 boundary-layer transition on a cone at angle of attack

Boundary-layer transition on a sharp 5-deg half-angle cone at incidence was investigated at Mach 3.5 in NASA's Supersonic Low-Disturbance Pilot Tunnel. The tests were conducted with low and high levels of freestream acoustic disturbance, and four angles of attack (alpha/theta-c = 0, 0.12, 0.4, and 0.8). Transition data, obtained with and without significantly reduced freestream acoustic disturbance levels, are compared with conventional ('noisy') wind-tunnel data. It was found that, under quiet flow conditions, there was no significant unit Reynolds number effect, whereas with noisy flow conditions, a significant unit Reynolds number effect was measured on and near the windward ray for alpha/theta-c values 0.4 and 0.8.

King, Rudolph A.↗
NASA NTRS1997

Turbine blade tip/outer airseal/platform flow analysis

The interaction between the main passage flow through a high pressure turbine and the secondary flows due to leakage through the wheelspace rim seals is reviewed. Various experimental and analytical studies of these interactions are outlined and a numerical investigation of the interaction between the main passage flow and a wheelspace cavity seal flow is described. The numerical investigation uses a structured grid method to study the overall interaction between the turbine stage components and the wheelspace seal flow, and an unstructured grid method to resolve the detailed flow features within the geometrically complex cavity seal. The numerical results agree with various observations from experimental studies under similar flow conditions. As the flow rate through the rim cavity seal is increased, the ingestion of fluid from the main passage flow into the rim seal area decreases rapidly. A small amount of main flow gas is ingested into the rim seal area, even at high seal flow rates.

Hah, C.↗