Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ferritic steels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Acidic Gas Reduction For Residential Natural Gas Furnace

The United States has more than 119 million homes, and 47% of them rely on natural gas as their primary heating fuel. However, most U.S. homes still use noncondensing units with an annual fuel utilization efficiency (AFUE) of ~80%, rather than efficient condensing furnaces. This is due to the high cost of condensing furnaces, which usually use expensive corrosion resistant super-ferritic stainless steel alloy heatexchangers (HX) to avoid corrosion and fouling acid condensation, along with the cost and difficulty of retrofitting the venting used by the replaced furnace. Here, this article discusses a low-cost acidic gas reduction (AGR) catalyst technology that enables a novel condensing natural gas furnace with an ultraclean (i.e., nearly zero) flue gas and neutral condensate that is environmentally friendly.

03 NATURAL GAS↗
DOE OSTI2022

Specimen Size and Geometry Effects on the Master Curve Fracture Toughness Measurements of EUROFER97 and F82H Steels

EUROFER97 and F82H are two leading reduced-activation ferritic-martensitic (RAFM) steels for fusion blanket applications. Exposure to the harsh environment of fusion reactors can result in severe degradation of materials fracture toughness (FT). Thus, the post-irradiation evaluation of FT is critical to understanding the material behavior. Due to the space constraint of irradiation facilities, the development of small specimen test techniques (SSTT) is necessary to evaluate the performance of irradiated materials. In this study, we evaluated the specimen size and geometry effects on the ductile-to-brittle transition FT of EUROFER97 batch-3 and F82H-BA12 steels. The specimen thicknesses ranged from 1.65 to 12.7 mm and the geometries included 1.65 mm bend bar, 4 mm mini-compact tension (miniCT), and 0.5T compact tension (CT) specimens. Fracture toughness testing and evaluations were performed using the Master Curve method in the ASTM E1921-19 standard. After size correction to 1T size using the Master Curve method, no specimen size effect was observed between the 4 mm miniCT and 0.5T CT specimens for the Master Curve reference temperature T0Q, while the bend bars yielded a higher T0Q. A strong effect of fatigue precrack front straightness on T0Q for 0.5T CT specimens was observed. The minimum number of specimens needed for each specimen geometry has been determined.

Chen, Xiang↗
DOE OSTI2024

Microstructural and Hall–Petch Analysis of Additively Manufactured Ferritic Alloy Using 2507 Duplex Stainless Steel Powder

The powder bed fusion–laser beam (PBF-LB) process, a method of additive manufacturing (AM), was used to print duplex stainless steel (DSS) using commercial-grade 2507 powders. While conventionally processed DSS has a two-phase microstructure consisting of 50% austenite and 50% ferrite, the PBF-LB-printed 2507 alloy was nearly 100% ferrite. Optimal processing conditions that minimized porosity were determined to be 290 W laser power and 1000 mm/s scan speed, and grain size, texture, and phases were characterized as a function of laser power and scan speed. Grain size increased with increasing laser power but decreased with increasing scan speed. A <100> texture diminished with increasing scan speed from 1000 mm/s to 1400 mm/s. No austenite phase was detected. Transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) characterization revealed nanoscale chromium nitride precipitates in the ferritic matrix (incoherent hexagonal close-packed (HCP) precipitates at grain boundaries and coherent body-centered cubic (BCC) precipitates within the grains) and a high density of tangled dislocations. Tensile tests of as-printed alloys showed a yield strength of 570 MPa, an ultimate tensile strength of 756 MPa, and an elongation to failure of 10%. The tensile properties were analyzed based on the observed microstructure considering grain size, nanoscale precipitates, and the high density of dislocations.

Crystallography↗
DOE OSTI2022

STEM imaging of irradiation induced defects in Eurofer97 steel variants irradiated in the EUROfusion collaboration

Ten exploratory variants of Eurofer97 reduced activation ferritic martensitic (RAFM) steel were irradiated in HFIR to ~2.94 – 32.4 dpa, 300±30 °C as a part of the EUROfusion collaboration. The irradiations were performed in rabbit capsules. ES21-22 capsule were used for irradiating SS-J3 tensile samples while M4CVN bend bar samples were irradiated in ES31-35 capsules. The mechanical properties and multi-length scale characterization of the microstructures of these ten steels, designated as H, I, P, J, K, L, M, N, O, P and reference E, in the nonirradiated form was reported in "Mechanical properties and microstructure characterization of unirradiated Eurofer-97 steel variants for the EUROfusion project, ORNL/SPR-2018/882," while their irradiated properties and some microstructure analysis was reported in "Post-irradiation examination of Eurofer97 steel variants irradiated to 2.5 dpa, ~300 °C in HFIR for the EUROfusion program, ORNL/SPR-2020/1440." Here, additional microstructures using TEM/STEM and STEM-EDX of the irradiated steels is presented. Characterization was performed at the Low Activation Materials Development and Analysis (LAMDA) laboratory.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High temperature oxidation of corrosion resistant alloys from machine learning

Parabolic rate constants, k p , were collected from published reports and calculated from corrosion product data (sample mass gain or corrosion product thickness) and tabulated for 75 alloys exposed to temperatures between ~800 and 2000 K (~500–1700 °C; 900–3000°F). Data were collected for environments including lab air, ambient and supercritical carbon dioxide, supercritical water, and steam. Materials studied include low- and high-Cr ferritic and austenitic steels, nickel superalloys, and aluminide materials. A combination of Arrhenius analysis, simple linear regression, supervised and unsupervised machine learning methods were used to investigate the relations between composition and oxidation kinetics. The supervised machine learning techniques produced the lowest mean standard errors. The most significant elements controlling oxidation kinetics were Ni, Cr, Al, and Fe, with Mo and Co composition also found to be significant features. The activation energies produced from the machine learning analysis were in the correct distributions for the diffusion constants for the oxide scales expected to dominate in each class.

Materials Science↗
DOE OSTI2024

Evaluation of liquid metal embrittlement of F82H and 4340 steels in liquid lithium

Here, to evaluate the liquid metal embrittlement (LME) susceptibility of F82H, a reduced activation ferritic-martensitic (RAFM) steel, a testing procedure using hollow cylindrical tensile specimens was used. Tensile tests are compared between specimens filled with argon and lithium at 200 °C. To validate the procedure, initial testing was performed on type 4340 steel, which is well-known to exhibit LME. Compared to 4340 steel, F82H only showed minor effects of Li exposure, including pre-testing exposures with Li at 400 °C for 1 h and 500 °C for 500 h. Furthermore, changing the strain rate or tensile test temperature also did not show significant embrittlement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Radiological analysis and transmutation calculation of representative castable nanostructured alloys

In this work, radiological analysis regarding the waste management was performed on two current reduced-activation ferritic-martensitic (RAFM) steels Eurofer 97 and F82H and two castable nanostructured alloys (CNAs) CNA1 and CNA3 using the European DEMO first wall spectrum. CNA1 and CNA3 are a new generation of RAFM steels, which have increased amounts of nanoscale carbonitrides and carbides precipitates, respectively, via small composition modifications. Furthermore, the increased nitrogen in CNA1 leads to higher activity at ≥50 years, and thus to the disposal concern under the current NRC regulation. However, the calculation using Fetter’s evaluation leads to reduced waste disposal rating (WDR) of down to 0.25 depending on the damage dose from ~0.05 wt percent nitrogen in CNA1, and thus less concern on the waste disposal. Contact dose rate after 10 years from the first wall replacement primarily depends on the initial Co and Nb impurity levels. Other added elements, such as V and Si in CNA1 and Ti and Mn in CNA3, do not have significant effect on the specific activity, contact dose rate, or decay heat. Composition limits of CNAs are given based on the shallow burial disposal and materials recycling. In addition, composition evolution of typical precipitates in the CNAs was calculated using the DEMO first wall and the HFIR spectra. Larger transmutation-induced composition evolution occurs in the V/Ta-rich carbonitrides in CNA1 than that in the Ti-rich carbides in CNA3.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Tailoring Carbide Dispersed Steels: A Path to Increased Strength and Hydrogen Tolerance

The use of transition metal carbides is reported for use as a hydrogen trapping mechanism for ferritic and austenitic steel materials. The program combined computational modeling and simulations to guide experiments towards candidate metal carbide traps, both for interfacial and interior trapping. It was found that interfacial trapping is less effective than interior trapping, with the group IVB transition metal carbides being the most effect internal traps with a loss of carbon. The sub-stoichiometric rocksalt structure accommodate the hydrogen atoms in its octahedral interstices. Using percolation theory, carbon loss of approximately 25% or more was sufficient to ensure an interconnected network of vacancies for such trapping from the surface to the internal sites within the carbide. Using this as a guide, the program developed a means to provide a uniform dispersion of ZrC nanoparticles with either Fe or 304L micron-scale powders which was then consolidated by direct current sintering. Electrolytic hydrogen diffusivity studies confirmed the reduction of hydrogen diffusion in the matrix with increasing ZrC content, which was a linear response over the sample range studied (0.01 to 1.0 wt.%). The consolidated material was micro-tensile tested in either a non-hydrogen or hydrogen charge condition and compared to a control with no carbides. Additions up to 0.05 wt.% ZrC increased the yield strength with no loss in ductility in either the non-hydrogen or hydrogen tested condition. ZrC concentrations above this amount further increased the yield strength at the expense of ductility. While these samples had a lower absolute ductility value prior to failure, the relative change in ductility between the non-hydrogen and hydrogen charge states was less for the carbides than that of the control. Metal-rich ZrC nanoparticles were fabricated through a conformal coating process yielding ZrC0.66 particles that were then incorporated into a metal matrix. Notch fatigue testing in a hydrogen environment was conducted where the number of cycles to failure was found to be less in the control than that of the carbide addition. However, the spread in experimental data and the number of samples tested limits a conclusive outcome based on defects noticed in the gauge section of all the powder processed samples. The collective outcomes of this report provide further insight into the mechanisms by which carbides act as hydrogen traps; a means to process such carbides through powder metallurgy; and their associated mechanical performance in either a non-hydrogen or hydrogen-charged condition.

08 HYDROGEN↗
DOE OSTI2022

Compatibility Of Steels At 450°-650°C In Supercritical CO2 With O2 And H2O Additions

Direct-fired supercritical CO2 (sCO2) power cycles are being commercialized to revolutionize fossil energy as a low-emission power source. However, the cycle will increase O2 and H2O in the sCO2 and the implications of these additions have not been fully studied, particularly for lower cost steels that are needed in the lower temperature segments of the plant. Representative 9 and 12%Cr ferritic-martensitic (FM) steels and conventional and advanced austenitic steels were evaluated at 450-650°C to determine the maximum use temperatures in sCO2 with 1%O2 and 0.1%H2O at 300 bar. Compared to research grade (low impurity) sCO2 in indirect-fired cycles, the mass gains and scale thickness were not significantly changed for FM steels: both formed thick duplex Fe-rich scales. For stainless steels, higher mass gains were observed in all cases with increased Fe-rich oxide nodule formation. After 1000h at 650°C, the measured bulk C content was high for all of the steels with the addition of impurities suggesting a lower maximum operating temperature for steels. The post-exposure impact of the environment on room temperature tensile properties also will be discussed.

Pint, Bruce↗
DOE OSTI2024

Effect of Impurities on the Compatibility of Steels in Supercritical CO 2 at 450°–650°C

Direct-fired supercritical CO 2 (sCO 2 ) power cycles are a pathway to low-CO 2 fossil energy but contain O 2 and H 2 O in the sCO 2 from combustion. The effect of impurities on structural steels was investigated at 450°-650 °C in 30 MPa sCO 2 . The test matrix included 9 and 12%Cr ferritic-martensitic (FM) steels and conventional and advanced austenitic steels exposed for 1000-2000 h with and without additions of 1%O 2 and 0.1%H 2 O to simulate the cycle after water removal. For FM steels, the mass gains and scale thicknesses were similar with and without impurities with the formation of thick, duplex Fe-rich scales in all cases including the observation that Fe 2 O 3 only formed with 1%O 2 . For the austenitic steels, higher mass gains were observed at all temperatures with increased formation of Fe-rich oxides when impurities were added. Carbon ingress was assessed by bulk combustion analysis, glow discharge optical emission spectroscopy (GDOES) and measuring postexposure room temperature tensile properties. In conclusion, bulk C content was strongly increased at 650 °C but not at 450° or 550 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tuning austenite stability through prior microstructure control in a low-alloy Q&P steel

Quenching and partitioning (Q&P) processing is a widely accepted heat treatment methodology for creating high strength steels consisting of ferrite, martensite, and austenite, while maintaining relatively low manufacturing costs. Though the research on effects of prior microstructure is limited, an understanding of the heat treatment response of different starting microstructures is critical to processing and creating steels with complex microstructures that contain retained austenite and may afford opportunities to further optimize properties. This study investigates the influence of starting microstructure (ferrite/pearlite versus martensite) and prior levels of cold work (38 verses 58 %) on the microstructural development and mechanical properties of a 0.2 C-2.0 Mn-1.5 Si (wt.%) steel exposed to Q&P processing. Samples with a starting martensitic microstructure resulted in higher retained austenite fractions and a more homogeneous microstructure after Q&P processing compared to a starting microstructure of ferrite-pearlite. Starting martensitic microstructures also displayed higher work hardening rates and higher uniform elongations. Larger cold reductions saw accelerated dissolution kinetics and austenite formation during intercritical annealing, resulting in more similar final microstructures from the ferrite-pearlite and martensitic starting microstructures. Finally, the results presented here indicate that varying prior processing can be a route to manipulate and control austenite stability in a Q&P processed steel.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The effect of helium on cavity swelling in dual-ion irradiated Fe and Fe-10Cr ferritic alloys

We report Ferritic-martensitic (FM) steels for in-vessel components in proposed fusion reactors are expected to suffer from high levels of displacement damage and helium (He) generation by neutron transmutation. However, a thorough understanding of the He synergistic effects on the cavity swelling in FM steels is still not well established. To gain fundamental insights into the He effect on cavity swelling, high purity Fe and Fe-10 wt.% Cr ferritic model alloys were irradiated with 8 MeV Ni ions and co-implanted He ions at 400 to 550 °C up to 30 displacements per atom (dpa) with He implantation rates of 0.1, 10 and 50 appm He/dpa. The current study focuses on the 50 appm He/dpa, 500 °C behavior vs. 0.1 and 10 appm He/dpa. Irradiation-induced defects, including cavities, dislocation loops, and dislocation networks were characterized using transmission electron microscopy (TEM). In the grain interior, a bimodal cavity size distribution was observed in the 10 and 50 appm He/dpa samples, but not for 0.1 appm He/dpa. Cavity swelling was maximized at intermediate He implantation rates of ~10 appm He/dpa for both ion-irradiated Fe and Fe-10Cr alloys. The cavity swelling behavior as a function of He implantation rate appears to be controlled by the He/dpa-dependent variation of cavity sink strengths. Treating small bubbles as biased sinks for interstitial absorption can significantly increase the ratio of biased to unbiased sink strengths (Q) and results in maximized cavity swelling for a Q ratio close to one.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High Performance Computing to Quantify the Evolution of Microscopic Concentration Gradients During Flash Processing

During the Flash process, the cross section of a plain-carbon or a low-alloy steel is austenitized through rapid heating and transformed on rapid cooling to a predominantly martensite + bainite structure with small amounts of retained austenite. Unlike conventional heat treating, homogeneity is intentionally avoided during Flash processing of steels. The Flash process assembly consists of a pair of rolls that transfer the steel sheets through the heating and cooling stage of the thermal cycle. The initial microstructure of the steel consists of ferrite (body-centered cubic iron) + carbide ((Fe,X)mCn) mixture. The heating rate through the peak temperature is a function of temperature and reaches a peak of about 300-400°C/s and the cooling rate has a maximum value of 3,000-4,000°C/s. The on-heating phase transformations include carbide dissolution, austenite (face-centered cubic iron) nucleation and growth, and diffusion of carbon and other substitutional elements in the steel. The on-cooling phase transformations include formation of martensite (body-centered tetragonal phase containing supersaturated solute) and bainite (ferrite plates with or without fine carbides). In this project, the focus is on Fe-C-Cr steels that are currently Flash processed for armor applications. The modeling effort proposed here will help optimize the Flash thermal cycle for these low alloy steels to achieve the target performance, which is an ongoing effort at SFP Works. A significant feature of Flash processed Fe-C-Cr steels is the presence of scatter in the through-thickness in the sheet. The variability in hardness results from a variability in the bainite + martensite microstructure that is sensitive to the local chemical concentration of C and Cr. Such a chemical inhomogeneity is intentionally obtained in the Flash process. Although such a microstructural gradient is presumably responsible for the exceptional properties of the Flash processed steel, it is very important to quantify the gradients as a function of Flash variabilities in processing parameters and the input microstructure. Understanding the mechanistic pathway that leads to microstructural gradients could be ground-breaking and instrumental for achieving better process control and optimized microstructural state to meet application-specific strength-ductility requirements. Since the final microstructure depends on setting up precise solute concentration gradients through a rapid heating process, and transforming these regions into various phases, it is important to understand how small changes in steel chemistry, input microstructure (carbide size and distribution), and process variables (Flash thermal cycle) will impact the solute concentration gradients.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

SA508 low alloy steel to 316L stainless steel dissimilar metal joint made by powder metallurgy hot isostatic pressing

Joining ferritic SA508 low alloy steel (LAS) and austenitic 316 L stainless steel (SS) via powder metallurgy hot isostatic pressing (PM-HIP) was evaluated as an alternative method to welding. This study investigated the mechanical and microstructural evolutions of the bimetallic interface under different joint designs and heat treatments. Here, the direct joining of dissimilar metal alloys by PM-HIP method resulted in two designs: 1) powder SA508 to solid bar 316 L (P508–B316L) and 2) powder 316 L solid bar SA508 (P316L-B508). In both cases, P508–B316L and P316L-demonstrated satisfactory tensile strength, however, high hardness and severe depreciation in toughness were located on the bimetallic interface. The mechanisms responsible for the detrimental mechanical properties were verified. Large oxides were observed in P508–B316L due to the prior powder boundary (PPB) oxides present in SA508 powder. The intense sensitization occurred from the formation of M 23 C 6 carbides, consequently from the slow cooling after PM-HIP in P316L-B508. Post-HIP heat treatments were explored to reduce the distance of carbide formation; however, the heat treatment could not eliminate the carbides. The experimental results were compared to the diffusion couple simulation as a function of carbide formation with distance. The analysis also showed the high hardness at the bimetallic interface was primarily contributed by solid solution strengthening. In conclusion, the direct joining of P316L-B508 and P508–B316L via PM-HIP was deemed to be unfeasible, and a transitional material is necessary to impede the diffusion of carbon.

316L stainless Steel↗
DOE OSTI2025

Mitigated Dissimilar Mass Transfer with Aluminized RAFM Steels in Flowing PbLi at 650°C

To evaluate dissimilar material interactions in flowing eutectic Pb-16at. %Li between fusion-relevant materials and to establish a maximum operating temperature of future blanket designs, a series of thermal convection loop (TCL) experiments with flowing PbLi have been conducted. Following a 1000-h, 550°C to 650°C TCL experiment, a thin reaction product was observed on the surface of monolithic, high-purity SiC. To identify the source of the observed dissimilar material interaction and to understand the reaction kinetics, an identical 2000-h TCL exposure was conducted, but less reaction of the SiC specimen was observed. Characterization of the FeCrAlMo (alloy APMT) loop tubing and the PbLi-exposed austenitic stainless steel (SS) assembly parts suggested that the formation of the reaction layer on the surface of the PbLi-exposed SiC did not originate from the coated reduced activation ferritic martensitic (RAFM) steel, but from the dissolved loop materials (liquid metal exposed APMT tubing and type 316 SS fittings). Here, the results, after 2000 h, suggest that the dissimilar material reaction between the Al-coated RAFM steel and the SiC has very slow reaction kinetics within a temperature gradient of 550°C to 650°C.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Inverse design of hypoeutectoid pearlite steel microstructures using a deep learning and genetic algorithm optimization framework

Goal-oriented microstructure design in metallic materials is a challenging task due to complex structure-property relationships. Traditional experimental and computational approaches are time-intensive and economically inefficient, limiting their applicability for large-scale design space exploration. Here, in this work, we propose an end-to-end framework that integrates deep learning models with genetic optimization to design microstructures with targeted mechanical properties. Deep learning models enable accurate forward design, while their integration with genetic optimization enables efficient inverse design within a few hours, compared to days or weeks using conventional finite element simulations. The framework combines experimental characterization and finite element modeling to analyze the influence of microstructural features on the mechanical behavior of hypoeutectoid steels. Data from both experiments and simulations are used to train the deep learning models. To demonstrate its effectiveness, we apply the framework to 0.63% carbon steel with proeutectoid ferrite and pearlite phases, commonly used in industrial applications. In this study, 2D microstructures were used for modeling, selected primarily for computational efficiency and to establish proof of concept. The framework successfully optimizes microstructures for targeted yield strength, ultimate strength, and stress concentration factors while significantly reducing computational time. Beyond hypoeutectoid steels, this scalable framework can be extended to other material systems and integrated with additive manufacturing, offering an efficient approach for accelerating microstructure design for specific engineering applications.

ConvLSTM↗
DOE OSTI2021

Technological aspects in blanket design: Effects of micro-alloying and thermo-mechanical treatments of EUROFER97 type steels after neutron irradiation

Presently available data on neutron irradiation damage raise doubts on the feasibility of using EUROFER97 steel for a water-cooled starter blanket in a DEMO reactor, since the ductile-to-brittle transition temperature (DBTT) increases significantly for irradiation temperatures below 350°C. The additional DBTT shift caused by H and He transmutation can only be estimated based on very few results with isotopically tailored EUROFER97 steel. Conservative calculations show that the DBTT of EUROFER97 steel could exceed the operating temperature in water-cooled starter blankets within a relatively short time period. This paper presents results from a EUROfusion funded irradiation campaign that was performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. The paper compares ten newly developed reduced activation ferritic-martensitic (RAFM) steels irradiated to a nominal dose of 2.5 dpa at 300°C. The post-irradiation experiments using Small Specimen Test Technology included hardness, tensile, and fracture mechanics tests combined with fractography and microstructure analysis are presented. Results show that micro-alloying EUROFER97-type steels influenced the mechanical properties but a dominating impact on irradiation damage resistance could not be identified. In contrast, specific thermo-mechanical treatments lead to better DBTT behavior. Discussion about irradiation response to heat treatment conditions is also given. Here, despite requiring data also at high dpa values, the results indicate that with these modified materials an increased lifetime and potentially also an increased operating temperature window can be achieved compared to EUROFER97.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗