Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLUIDIZED BEDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Combustion of hydrogen in a bubbling fluidized bed

The combustion of hydrogen in a hot, bubbling bed of quartz sand fluidized by air has been studied for the first time, by injecting hydrogen just above the distributor, via six horizontal fine tubes of Cr/Ni. Overall the fluidizing gas was oxygen-rich, with the composition varying from nearly stoichiometric to very lean mixtures. With the bed initially fluidized at room temperature, combustion (after ignition by a pilot flame) occurs in a premixed flame sitting on top of the bed. When the sand warms up, combustion becomes explosive in bubbles leaving the bed, exactly as with a hydrocarbon as fuel. However, in contrast to hydrocarbons, it is clear that when the bed reaches 500-600 C, heat is produced both above the top of the bed (because of H{sub 2} bypassing the bed) and very low down in the bed. In fact, with hydrogen as fuel, the location of where bubbles ignite descends abruptly to low in the sand; furthermore, the descent occurs at {proportional_to}500 C, which is {proportional_to}100 K below the ignition temperature predicted by well-established kinetic models. However, the kinetic models do reproduce the observations, if it is assumed that the Cr/Ni hypodermic tubes, through which the fuel was injected, exert a catalytic effect, producing free H atoms, which then give rise to HO{sub 2} radicals. In this situation, kinetic modeling indicates that bubbles ignite when they become sufficiently large and few enough to have a lifetime (i.e. the interval between their collisions) longer than the ignition delay for the temperature of the sand. The amounts of NO found in the off-gases were at a maximum (24 ppm), when the bed was at {proportional_to}500 C for {lambda}=[O{sub 2}]/[O{sub 2}]{sub stoich}=1.05. The variations of [NO] with [air]/[H{sub 2}] and also temperature indicate that NO is produced, at least partly, via the intermediate N{sub 2}H. In addition, the air-afterglow emission of green light (from NO+O{yields}NO{sub 2}+h{nu}) was observed in the freeboard, indicating the presence there of both NO and free atoms of oxygen for 1.05<{lambda}<1.1. (author)

08 HYDROGEN↗

Structure and Reactivity of Low-Rank Coal Chars Prepared from Fluidized Bed and Moving Bed Pyrolyzers and the Potential for Using Them in Pulverized Coal Injection (PCI)

Utilizing pyrolysis chars as the injection fuel in a blast furnace can reduce the dependence on high-quality pulverized coal injection (PCI) coal. In this study, the physical properties and reaction characteristics of chars prepared from two different industrial-scale pyrolyzers (fluidized bed and moving bed) are investigated. The results reveal remarkable component segregation in the char particles with different particle sizes. The properties of large-size char particles are found to better satisfy the PCI fuel requirement in a blast furnace. Compared with PCI coal, the char particles exhibit a rough surface, well-developed pore structure, and less-ordered chemical structure of carbon. Results from isothermal combustion, isothermal gasification, and drop tube furnace experiments show that both types of chars exhibit a better reactivity than PCI coal. The excellent reactivity of chars is closely related to its high Brunauer–Emmett–Teller surface area and relatively poor chemical ordering during conversion. Based on these characteristics, both fluidized bed char (FBC) and moving bed char (MBC) have a great potential to be used as PCI fuels. The application method of chars for PCI in a blast furnace is proposed finally.

01 COAL, LIGNITE, AND PEAT↗

Using Chemical Reactor Models to Predict Fluidized Bed Pyrolysis Yields of Biomass Feedstocks

A detailed biomass pyrolysis kinetics scheme is implemented in reduced-order reactor models to predict chemical species yields from a fluidized bed reactor. The biomass composition in terms of cellulose, hemicellulose, lignins, and extractives are determined for several biomass feedstocks. Model results are compared to yields measured from a two-inch diameter bench-scale fluidized bed reactor operating at fast pyrolysis conditions. The reduced-order chemical reactor models compare favorably with the experimental measurements and capture trends in product yields due to biomass compositional effects such as high ash content. This work offers a computationally inexpensive approach to predict the quality of biomass pyrolysis products in a timely manner. Source code for the reactor models along with a biomass composition web tool are made available online for future scientific research efforts.

09 BIOMASS FUELS↗

Dimensionless Regime Mapping and Chaos Analysis of Solids Volume Fraction Data in a Circulating Fluidized Bed Riser

Presentation of experimental results of solids volume fraction data measurements in a 12-inch diameter cold flow circulating fluidized bed in relation to a dimensionless fluidization regime map. Statistical and chaotic system analysis results are shown to illustrate differences in hydrodynamic behavior at different operating conditions. Presentation was made at the ASTFE 10th Thermal and Fluids Engineering Conference, March 09-12, 2025.

chaos↗

Fluidization Regime Mapping Analysis for 200 μm Glass Beads in a Circulating Fluidized Bed Riser

Powerpoint slides for an oral presentation at the 2024 Clearwater Clean Energy Conference. It includes a brief discussion of a recently developed non-dimensional map for scaling circulating fluidized bed risers using velocity and solids circulation rate ratios. Data is presented for a set of experiments conducted in NETL’s 12-inch cold flow circulating fluidized bed (CFCFB) riser with 200 micron diameter glass beads, showing a strong dependance between solids volume fraction profiles and the solids circulation rate ratio.

Rowan, Steven↗

Development and Validation of a Dynamic Response Model for a Cold Flow Circulating Fluidized Bed

A dynamic response model has been created of the Cold Flow Circulating Fluidized Bed at NETL in Morgantown, WV. The model is considered dynamic, as opposed to steady state, because it is used to predict the transient responses of gas and solids flows throughout the unit as process conditions vary. The model was built in ProTrax with Advanced Continuous Simulation Language (ACSL) custom code. Dynamic experiments, varying both gas and solids flows, in the CFB unit have been used to validate the accuracy of the model. The advantage of this model is its utility in predicting gas hold up and solids flow throughout the unit during transitions of process conditions. Accurate predictions of these phenomena are important in process control and optimization. The dynamic experiments used in validating the model include modulations of the system pressure, move air (solids flow), and riser gas velocity with step and sinusoidal changes.

01 COAL, LIGNITE, AND PEAT↗

Analysis of a Fluidized-Bed Particle/Supercritical-CO2 Heat Exchanger in a Concentrating Solar Power System

Concentrating solar power (CSP) development has focused on increasing the energy conversion efficiency and lowering the capital cost. To improve performance, CSP research is moving to high-temperature and high-efficiency designs. One technology approach is to use inexpensive, high-temperature heat transfer fluids and storage, integrated with a high-efficiency power cycle such as the supercritical carbon dioxide (sCO 2 ) Brayton power cycle. The sCO 2 Brayton power cycle has strong potential to achieve performance targets of 50% thermal-to-electric efficiency and dry cooling at an ambient temperature of up to 40 °C and to reduce the cost of power generation. Solid particles have been proposed as a possible high-temperature heat transfer or storage medium that is inexpensive and stable at high temperatures above 1000 °C. The particle/sCO 2 heat exchanger (HX) provides a connection between the particles and sCO 2 fluid in emerging sCO 2 power cycles. This article presents heat transfer modeling to analyze the particle/sCO 2 HX design and assess design tradeoffs including the HX cost. The heat transfer process was modeled based on a particle/sCO 2 counterflow configuration, and empirical heat transfer correlations for the fluidized bed and sCO 2 were used to calculate heat transfer area and estimate the HX cost. A computational fluid dynamics simulation was applied to characterize particle distribution and fluidization. This article shows a path to achieve the cost and performance objectives for a particle/sCO 2 HX design by using fluidized-bed technology.

14 SOLAR ENERGY↗

Determining Design Criteria for Feeding Biomass into a Fluidized Bed Using a Feed Screw

Many pathways have been discovered for the thermochemical conversion of biomass to products. These pathways often show very promising results on the benchtop scale and could be economical with the appropriate scale up. However, many of the fundamental challenges of scaling up thermochemical reactions are not well understood. One primary problem area that rarely receives much upfront attention is feeding large quantities of biomass into thermochemical reactors. As biomass transitions from ambient to reactor conditions, it undergoes chemical and physical changes that affect its flowability. Often these changes lead to agglomeration of feed particles within the transfer screw, leading to large clumps of feed entering and disrupting the fluidized bed, or more critically leading to a plug in the feed screw causing costly downtime and maintenance to remove. This transitional phase must be better understood for scale up of conversion technologies to be successful. The Feedstock-Conversion Interface Consortium (FCIC) is a collaboration of eight National Laboratories. FCIC is currently conducting research on screw feeding of biomass into thermochemical fluidized bed reactors. Heat transfer models have been constructed for the screw/reactor interface. Mechanical forces on biomass within screw feeder are being determined, as well as how those forces change by varying feed screw design. Feedstock physical and chemical properties are then being measured along these temperature and mechanical force gradients. This work will better inform feed screw design for scale up, increasing the success rate of future biorefineries. Discussion will include research approach, testing, and preliminary results.

09 BIOMASS FUELS↗

Particle-wall heat transfer in narrow-channel bubbling fluidized beds for thermal energy storage

Robust metal oxide particles can provide low-cost and stable thermal energy storage (TES) to temperatures up to 1200 °C or higher. The transfer of heat into and out of the particles in cost-effective high-temperature particle heat exchangers remains a principal challenge to implementing particle-based TES. The present work expands on prior studies of particle-wall heat transfer in narrow-channel fluidized beds operated in the bubbling fluidization regime. Batch-mode experiments with various oxide particles over a range of temperatures and airflow rates indicate that particle-wall heat transfer increases with higher bed temperature and decreasing particle size. Measured particle-wall heat transfer coefficients in a 12 mm deep channel are fit to a Nusselt number correlation proportional to a non-monotonic function of excess fluidization velocity. Particle-wall heat transfer coefficients rise rapidly with excess fluidization velocities until reaching a maximum at intermediate air velocities due to a trade-off between enhanced transverse particle mixing and decreasing particle volume fraction with increased fluidization velocity. The heat transfer coefficient reaches a maximum of ≈ 400% of values without fluidization for oxide particles ranging in diameter d p from 159 to 408 μm. For the smallest particles tested, composed of olivine sand, particle-wall heat transfer coefficients peak above 1100 Wm –2 K –1 at 450 °C. 100-h tests at 500 °C and near-optimal heat transfer fluidization velocities indicated minimal wall wear or oxide scaling. Furthermore, high particle-wall heat transfer coefficients suggest narrow channel fluidized beds as a potential pathway for reducing the required surface area and cost of high-temperature particle heat exchangers, as needed in large-scale thermal energy storage applications.

14 SOLAR ENERGY↗

The influence of temperature on limestone sulfation and attrition under fluidized bed combustion conditions

The influence of temperature on attrition of two limestones during desulfurization in a fluidized bed reactor was investigated. Differences in the microstructure of the two limestones were reflected by a different thickness of the sulfate shell formed upon sulfation and by a different value of the ultimate calcium conversion degree. Particle attrition and fragmentation were fairly small under moderately bubbling fluidization conditions for both limestones. An increase of temperature from 850 C to 900 C led to an increase of the attrition rate, most likely because of a particle weakening effect caused by a faster CO{sub 2} evolution during calcination. This weakening effect, however, was not sufficiently strong to enhance particle fragmentation in the bed. The progress of sulfation, associated to the build-up of a hard sulfate shell around the particles, led in any case to a decrease of the extent of attrition. Sulfation at 900 C was less effective than at 850 C, and this was shown to be related to the porosimetric features of the different samples. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved Fluidized-Bed Gas Injector

Gas-injection cone in fluidized-bed reactor for coating particles with silicon or carbon cooled and protected from abrasion by stream of gas flowing over surface of cone. Hot particles entering reaction zone are coated with silicon or carbon supplied by thermal decomposition of suitable gas injected into reaction zone.

Hogle, R. A.↗

Use of glow discharge in fluidized beds

Static charges and agglomerization of particles in a fluidized bed systems are minimized by maintaining in at least part of the bed a radio frequency glow discharge. This approach is eminently suitable for processes in which the conventional charge removing agents, i.e., moisture or conductive particle coatings, cannot be used. The technique is applied here to the disproportionation of calcium peroxide diperoxyhydrate to yield calcium superoxide, an exceptionally water and heat sensitive reaction.

Wydeven, T.↗

Sub-grid drag model for immersed vertical cylinders in fluidized beds

Immersed vertical cylinders are often used as heat exchanger in gas-solid fluidized beds. Computational Fluid Dynamics (CFD) simulations are computationally expensive for large scale systems with bundles of cylinders. Therefore sub-grid models are required to facilitate simulations on a coarse grid, where internal cylinders are treated as a porous medium. The influence of cylinders on the gas-solid flow tends to enhance segregation and affect the gas-solid drag. A correction to gas-solid drag must be modeled using a suitable sub-grid constitutive relationship. In the past, Sarkar et al. have developed a sub-grid drag model for horizontal cylinder arrays based on 2D simulations. However, the effect of a vertical cylinder arrangement was not considered due to computational complexities. In this study, highly resolved 3D simulations with vertical cylinders were performed in small periodic domains. These simulations were filtered to construct a sub-grid drag model which can then be implemented in coarse-grid simulations. Gas-solid drag was filtered for different solids fractions and a significant reduction in drag was identified when compared with simulation without cylinders and simulation with horizontal cylinders. Slip velocities significantly increase when vertical cylinders are present. Lastly, vertical suspension drag due to vertical cylinders is insignificant however substantial horizontal suspension drag is observed which is consistent to the finding for horizontal cylinders.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sintering and reactivity of CaCO{sub 3}-based sorbents for in situ CO{sub 2} capture in fluidized beds under realistic calcination conditions

Sintering during calcination/carbonation may introduce substantial economic penalties for a CO{sub 2} looping cycle using limestone/dolomite-derived sorbents. Cyclic carbonation and calcination reactions were investigated for CO{sub 2} capture under fluidized bed combustion (FBC) conditions. The cyclic carbonation characteristics of CaCO{sub 3}-derived sorbents were compared at various calcination temperatures (700-925{sup o} C) and different gas stream compositions: pure -2 and a realistic calciner environment where high concentrations of CO{sub 2}>80-90% are expected. The conditions during carbonation were 700 {sup o}C and 15% CO{sub 2} in N{sub 2} and 0.18% or 0.50% SO{sub 2} in selected tests. Up to 20 calcination/carbonation cycles were conducted using a thermogravimetric analyzer (TGA) apparatus. Three Canadian limestones were tested: Kelly Rock, Havelock, and Cadomin, using a prescreened particle size range of 400-650 {mu} m. Calcined Kelly Rock and Cadomin samples were hydrated by steam and examined. Sorbent reactivity was reduced whenever SO{sub 2} was introduced to either the calcining or carbonation streams. The multicyclic capture capacity of CaO for CO{sub 2} was substantially reduced at high concentrations of CO{sub 2} during the sorbent regeneration process and carbonation conversion of the Kelly Rock sample obtained after 20 cycles was only 10.5%. Hydrated sorbents performed better for CO{sub 2} capture but showed deterioration following calcination in high CO{sub 2} gas streams indicating that high CO{sub 2} and SO{sub 2} levels in the gas stream lead to lower CaO conversion because of enhanced sintering and irreversible formation of CaSO{sub 4}.

01 COAL, LIGNITE, AND PEAT↗

Fluidization Regime Mapping Analysis for 200 μm Glass Beads in a Circulating Fluidized Bed Riser

This paper was an executive summary for an oral presentation to be included in the conference proceedings of the 2024 Clearwater Clean Energy Conference. It includes a brief discussion of a recently developed non-dimensional map for scaling circulating fluidized bed risers using velocity and solids circulation rate ratios. Data is presented for a set of experiments conducted in NETL’s 12-inch cold flow circulating fluidized bed (CFCFB) riser with 200 micron diameter glass beads, showing a strong dependance between solids volume fraction profiles and the solids circulation rate ratio.

Rowan, Steven↗

The O{sub 2}-enriched air gasification of coal, plastics and wood in a fluidized bed reactor

Highlights: Black-Right-Pointing-Pointer The effect of the O{sub 2} in the gasification stream of a BFB gasifier has been studied. Black-Right-Pointing-Pointer Main advantage of the O{sub 2}-enriched air is the increasing of the bed temperature. Black-Right-Pointing-Pointer No remarkable effects on tar reduction. Decreasing of recognized PAHs. Black-Right-Pointing-Pointer Gasification reactions completed inside the dense bed and splashing zone. Black-Right-Pointing-Pointer Polycondensation reactions occur mainly in the freeboard region. - Abstract: The effect of oxygen-enriched air during fluidized bed co-gasification of a mixture of coal, plastics and wood has been investigated. The main components of the obtained syngas were measured by means of on-line analyzers and a gas chromatograph while those of the condensate phase were off-line analysed by means of a gas chromatography-mass spectrometer (GC-MS). The characterization of condensate phase as well as that of the water used as scrubbing medium completed the performed diagnostics. The experimental results were further elaborated in order to provide material and substances flow analyses inside the plant boundaries. These analyses allowed to obtain the main substance distribution between solid, gaseous and condensate phases and to estimate the conversion efficiency of carbon and hydrogen but also to easily visualise the waste streams produced by the process. The process performance was then evaluated on the basis of parameters related to the conversion efficiency of fuels into valuable products (i.e. by considering tar and particulate as process losses) as well as those related to the energy recovery.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Cartesian grid simulations of bubbling fluidized beds with a horizontal tube bundle

In this paper, the flow hydrodynamics in a bubbling fluidized bed with submerged horizontal tube bundle was numerically investigated with an open-source code: Multiphase Flow with Interphase eXchange (MFIX). A newly implemented cut-cell technique was employed to deal with the curved surface of submerged tubes. A series of 2D simulations were conducted to study the effects of gas velocity and tube arrangement on the flow pattern. Hydrodynamic heterogeneities on voidage, particle velocity, bubble fraction, and frequency near the tube circumferential surface were successfully predicted by this numerical method, which agrees qualitatively with previous experimental findings and contributes to a sounder understanding of the non-uniform heat transfer and erosion around a horizontal tube. A 3D simulation was also conducted. Significant differences between 2D and 3D simulations were observed with respect to bed expansion, bubble distribution, voidage, and solids velocity profiles. Hence, the 3D simulation is needed for quantitative prediction of flow hydrodynamics. On the other hand, the flow characteristics and bubble behavior at the tube surface are similar under both 2D and 3D simulations as far as the bubble frequency and bubble phase fraction are concerned. Comparison with experimental data showed that qualitative agreement was obtained in both 2D and 3D simulations for the bubble characteristics at the tube surface.

42 ENGINEERING↗