Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FIGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

A Preliminary Analysis of Dose Rates Associated with ITER CVCS Equipment/Area Location

A preliminary analysis of the ITER Chemical and Volume Control System (CVCS) Area was performed to assess dose rates outside the walls and ceiling of the facility after 1.5 years of operation at shutdown, 2 days, and 10 days after shutdown. For this purpose a simplified Monte Carlo computer model was developed using the MCNP (MCNP5 Ver. 1.51) code. Two components are included: the smaller filter tank and the larger ion exchanger. These pieces of equipment are associated with the Integrated Blanket ELM Divertor Primary Heat Transfer System, which will have the largest dose rates associated with activated corrosion products during operation in comparison with other systems. The ion exchanger contained two source regions, a 1.2-m-thick resin bed above a 0.55 m-thick skirt, and a 0.8-m-thick water region. The filter constituted an additional source. Thus the model consisted of three sources (filter, resin, water), homogeneously distributed within the appropriate source regions. However, much of the results (that address individual isotopes) are presented with the two sources in the ion exchanger combined. In these cases the sources are referred to as the 'ion exchanger source' and the 'filter source.' Dimensions for the facility and components, as well as source isotopes and strengths, and material densities, were supplied by US ITER. Because of its simplification, the model does not contain pipes. Consequently, radiation streaming through pipe penetrations, radiation emanating from the pipes, and shielding from the pipes were not considered in this analysis. Dose rates on the outside of two walls and the ceiling were calculated. The two walls are labeled as the 'long' wall (aligned with the X-axis) and the 'short' wall (aligned with the Y-axis). These walls and ceiling were nominally set to 30-cm-thick concrete. In the original analysis, standard concrete (2.3 g/cc density) was used. In addition to the shielding walls/ceiling, a floor and an additional wall opposite the long wall were added for photon scattering contributions. These were both 10-cm-thick, standard concrete structures. Other components (tanks, pipes, etc.), that were not included in the model, would potentially add additional scattering and shielding. Possibly these additional effects will be addressed in a later, more detailed analysis. The room was 29.6 m in length (X-axis), but was limited to 15 m in the model. The inside width (Y axis) and height (Z axis) were 4 m and 3.4 m, respectively. The origin for the model was located inside the room at the corner opposite the long wall and adjacent to the short wall at the floor level. The room was filled with air at standard temperature and pressure. The stainless steel (SS304) wall thicknesses for the ion exchanger and filter were 2.2 cm and 0.8 cm, respectively. The axial center of the filter was located 140 cm from the short wall and 100 cm from the long wall (outer surface). The axial center of the ion exchanger was located 440 cm from the short wall and 250 cm from the long wall (inner surface). The resin was assumed to be a homogeneous mixture of equal atom density fractions of hydrogen and carbon* at a specified density of 1.136 g/cc. The filter material was assumed to be homogeneous carbon at a specified density of 1.8 g/cc. If the filter media were stainless steel and the accumulated activity were the same, the dose rate outside the filter would be lower, provided the density of the stainless steel sintered filter material is significantly higher than 1.8g/cc. The densities of the water and air were assumed to be 1.0 g/cc and 1.096E-3 g/cc, respectively. The model included 10 small volumes placed outside the model adjacent to the wall at locations where the dose rates were expected to be highest and which showed to a degree the fall-off of the dose rate with distance along a particular wall or ceiling. These 'tally cells' are shown in Fig. 2 and are described in Table 1. Each cell had dimensions of 50 cm x 50 cm x 1 cm and was oriented so that the 1-cm-thick dimension was perpendicular to the wall against which the cell was located. Also, smaller tally volumes were placed at 5 cm (updated model), 30 cm, 50 cm, and 100 cm from each source, both radially from the outside of each component at the height of each source mid-plane, and vertically, along the axial centerline, above the ion-exchanger and below the filter. (For the ion exchanger, the vertical distance was limited to 75 cm because of interference from the ceiling.) These tally regions can be seen in Fig. 3. Each cell had dimensions of 5 cm x 5 cm x 1 cm, oriented so that the 1-cm-thick dimension was perpendicular to the X, Y or Z axis.

08 HYDROGEN↗

Year 2 Final Report - Protein Function Prediction Platform (v.0.5)

Upon completion of our second year of development in a 3-year development cycle, we have completed a prototype protein structure-function annotation and function prediction system: Protein Function Prediction (PFP) platform (v.0.5). We have met our milestones for Years 1 and 2 and are positioned to continue development in completion of our original statement of work, or a reasonable modification thereof, in service to DTRA Programs involved in diagnostics and medical countermeasures research and development. The PFP platform is a multi-scale computational modeling system for protein structure-function annotation and function prediction. As of this writing, PFP is the only existing fully automated, high-throughput, multi-scale modeling, whole-proteome annotation platform, and represents a significant advance in the field of genome annotation (Fig. 1). PFP modules perform protein functional annotations at the sequence, systems biology, protein structure, and atomistic levels of biological complexity (Fig. 2). Because these approaches provide orthogonal means of characterizing proteins and suggesting protein function, PFP processing maximizes the protein functional information that can currently be gained by computational means. Comprehensive annotation of pathogen genomes is essential for bio-defense applications in pathogen characterization, threat assessment, and medical countermeasure design and development in that it can short-cut the time and effort required to select and characterize protein biomarkers.

59 BASIC BIOLOGICAL SCIENCES↗

Initial Flowsheet for the Next Generation GSSX Process in the MCU: Report for FY2010

The Next Generation Caustic Side Solvent Extraction (NG-CSSX) flowsheet is being developed in a collaboration among Oak Ridge National Laboratory (ORNL), Argonne National Laboratory (ANL), and Savannah River National Laboratory (SRNL) for the Modular CSSX Unit (MCU) facility at the Savannah River Site (SRS). This work is being done in cooperation with two groups at SRS (my principal contacts there are Mark Geeting, SRR, and Sam Fink, SRNL) and with one group at Oak Ridge National Laboratory (my principal contact there is Bruce Moyer). The evaluation of the various NG-CSSX solvent candidates was done using the SASSE (Spreadsheet Algorithm for Stagewise Solvent Extraction) program with cesium distribution coefficient (D Cs ) values supplied by ORNL. The final optimized solvent composition has 50 mM MaxCalix as the extractant. Using the SASSE spreadsheet to calculate the Cs decontamination factor (D.F.) as well as ROTOR program to evaluate contactor rotor throughputs, an initial flowsheet was developed for the optimized NG-CSSX solvent. The current CSSX flowsheet for the MCU at its maximum salt feed flow rate is shown in Fig. 1. The initial NG-CSSX flowsheet for the MCU at its targeted maximum salt feed flow rate is shown in Fig. 2. Comparing these two flowsheets, one can see that, for the NG-CSSX flowsheet, the maximum flow rate of the salt feed (DF) is increased 41%, from 8.5 gpm to 12.0 gpm. At the same time, because of the high concentration of the MaxCalix extractant in the NG-CSSX solvent, the Cs decontamination factor (D.F.) for the aqueous effluent from the extraction section (DW, the aqueous raffinate) is increased from 12 to 40,000. As required, the Cs concentration factor (C.F.) for the aqueous effluent from the strip section (EW) is maintained at 15.

Leonard, Ralph↗

Conducting Polymer: Polyaniline

Electronically conductive polymers composites have gained tremendous attention over the last decade due to their unique properties for various applications such as rechargeable batteries, electromagnetic shielding, sensors and electronic devices. Polyaniline has been one of the most popular conducting polymer for the past fifty years. It has low density, good environmental stability, moderate conductivity and is considered as one of the most promising electrically conducting polymers. Polyaniline exists in three forms (Fig. 1): Leucoemeraldine, pernigraniline, and emeraldine. Leucoemeraldine is the fully reduced state and is white/clear colorless. Pernigraniline is the fully oxidized state with imine links instead of amine links and is blue/violet. The emeraldine form of polyaniline, often referred as emeraldine base (EB), is neutral and blue. When EB is doped, it turns green and is called emeraldine salt (ES) with the imine nitrogens protonated by an acid. EB delocalizes to the trapped diiminoquinone-diaminobenzene state, which is highly electrically conducting. Emeraldine base is regarded as the most useful form of polyaniline due to its high stability at room temperature. In this experiment, EB is doped with two different protonic acids (Fig. 3), 2-Acrylamido-2-methylpropane sulfonic acid (AMPSA) and camphorsulfonic acid (CSA), to compare the effectiveness of the dopants. The doped EB (ES) is later casted into films with a new resin to produce new polyaniline conductive composites and their conductivities are being studied.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

IC W13_fephases Highlight: Strong Size Dependence of Dynamic Instability Treatment in VASP Ab Initio Approach [Poster]

Phonon spectra at two different densities of bcc-Be at T slightly below the corresponding Tm. At P=0 the system is dynamically unstable at low T but stabilizes at T close to Tm=1560 K. However, unless the system size is 1458 atoms or higher (the number of valence electrons is ~ 3000 or more) dynamic instability is still present, in the form of an imaginary phonon branch at the Γ- point (Fig. 1). At P=300 GPa the system is dynamically stable for as low as 128 atoms (Fig. 2). This example demonstrates that at present it is unfeasible to treat bcc-Fe in the region of its dynamic instability (megabar pressure range) with the existing first-principles software (e.g., VASP) which only allows treating bcc-Fe with up to ~ 500 atoms (~7000 valence electrons).

36 MATERIALS SCIENCE↗

High Temperature Fluoride Salt Test Loop

Effective high-temperature thermal energy exchange and delivery at temperatures over 600°C has the potential of significant impact by reducing both the capital and operating cost of energy conversion and transport systems. It is one of the key technologies necessary for efficient hydrogen production and could potentially enhance efficiencies of high-temperature solar systems. Today, there are no standard commercially available high-performance heat transfer fluids above 600°C. High pressures associated with water and gaseous coolants (such as helium) at elevated temperatures impose limiting design conditions for the materials in most energy systems. Liquid salts offer high-temperature capabilities at low vapor pressures, good heat transport properties, and reasonable costs and are therefore leading candidate fluids for next-generation energy production. Liquid-fluoride-salt-cooled, graphite-moderated reactors, referred to as Fluoride Salt Reactors (FHRs), are specifically designed to exploit the excellent heat transfer properties of liquid fluoride salts while maximizing their thermal efficiency and minimizing cost. The FHR s outstanding heat transfer properties, combined with its fully passive safety, make this reactor the most technologically desirable nuclear power reactor class for next-generation energy production. Multiple FHR designs are presently being considered. These range from the Pebble Bed Advanced High Temperature Reactor (PB-AHTR) [1] design originally developed by UC-Berkeley to the Small Advanced High-Temperature Reactor (SmAHTR) and the large scale FHR both being developed at ORNL [2]. The value of high-temperature, molten-salt-cooled reactors is also recognized internationally, and Czechoslovakia, France, India, and China all have salt-cooled reactor development under way. The liquid salt experiment presently being developed uses the PB-AHTR as its focus. One core design of the PB-AHTR features multiple 20 cm diameter, 3.2 m long fuel channels with 3 cm diameter graphite-based fuel pebbles slowly circulating up through the core. Molten salt coolant (FLiBe) at 700°C flows concurrently (at significantly higher velocity) with the pebbles and is used to remove heat generated in the reactor core (approximately 1280 W/pebble), and supply it to a power conversion system. Refueling equipment continuously sorts spent fuel pebbles and replaces spent or damaged pebbles with fresh fuel. By combining greater or fewer numbers of pebble channel assemblies, multiple reactor designs with varying power levels can be offered. The PB-AHTR design is discussed in detail in Reference [1] and is shown schematically in Fig. 1. Fig. 1. PB-AHTR concept (drawing taken from Peterson et al., Design and Development of the Modular PB-AHTR Proceedings of ICApp 08). Pebble behavior within the core is a key issue in proving the viability of this concept. This includes understanding the behavior of the pebbles thermally, hydraulically, and mechanically (quantifying pebble wear characteristics, flow channel wear, etc). The experiment being developed is an initial step in characterizing the pebble behavior under realistic PB-AHTR operating conditions. It focuses on thermal and hydraulic behavior of a static pebble bed using a convective salt loop to provide prototypic fluid conditions to the bed, and a unique inductive heating technique to provide prototypic heating in the pebbles. The facility design is sufficiently versatile to allow a variety of other experimentation to be performed in the future. The facility can accommodate testing of scaled reactor components or sub-components such as flow diodes, salt-to-salt heat exchangers, and improved pump designs as well as testing of refueling equipment, high temperature instrumentation, and other reactor core designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Final Report: Non-Visible, Automated Target Acquisition and Tracking

The Roadside Tracker (RST) represents a new approach to radiation portal monitors. It uses a combination of gamma-ray and visible-light imaging to localize gamma-ray radiation sources to individual vehicles in free-flowing, multi-lane traffic. Deployed as two trailers that are parked on either side of the roadway (Fig. 1); the RST scans passing traffic with two large gamma-ray imagers, one mounted in each trailer. The system compensates for vehicle motion through the imager’s fields of view by using automated target acquisition and tracking (TAT) software applied to a stream of video images. Once a vehicle has left the field of view, the radiation image of that vehicle is analyzed for the presence of a source, and if one is found, an alarm is sounded. The gamma-ray image is presented to the operator together with the video image of the traffic stream when the vehicle was approximately closest to the system (Fig. 2). The offending vehicle is identified with a bounding box to distinguish it from other vehicles that might be present at the same time. The system was developed under a previous grant from the Department of Homeland Security’s (DHS’s) Domestic Nuclear Detection Office (DNDO). This report documents work performed with follow-on funding from DNDO to further advance the development of the RST. Specifically, the primary thrust was to extend the performance envelope of the system by replacing the visible-light video cameras used by the TAT software with sensors that would allow operation at night and during inclement weather. In particular, it was desired to allow operation after dark without requiring external lighting. As part of this work, the system software was also upgraded to allow the use of 64-bit computers, the current generation operating system (OS), software development environment (Windows 7 vs. Windows XP, and current Visual Studio.Net), and improved software version controls (GIT vs. Source Safe.) With the upgraded performance allowed by new computers, and the additional memory available in a 64-bit OS, the system was able to handle greater traffic densities, and this also allowed addition of the ability to handle stop-and-go traffic.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Final Technical Report for Quantum Embedding for Correlated Electronic Structure in Large Systems and the Condensed Phase

This is the final technical report. We briefly describe some selected results below. Developments in density matrix embedding. DMET is a quantum embedding theory that we introduced at the beginning of the last funding period, around 2012-2013. Since the first DMET papers, which demonstrated proof-of- principle calculations on the Hubbard model and hydrogen rings, we have carried out a number of different developments, including: Extending the DMET technology to compute broken symmetry phases, including magnetic phases and super- conductivity (Pub. 13); Calibrating the accuracy of DMET and its cluster size convergence against other methods, and formulation of a dynamical cluster analog (Pubs. 4, 10) (see Fig. 1); Implementing DMET for ab-initio molecular calculations, and exploring different self-consistency criteria (Pubs. 9, 14); Using embedding to defi ne quantum classical interfaces Pub. 2; Formulating DMET for spectral functions (Pub. 7) (see Fig. 1); Extending DMET to coupled fermion-boson problems (Pub. 12). Together with these embedding developments, we have also implemented a wide variety of impurity solvers within our DMET framework, including DMRG (Pub. 3), AFQMC (Pub. 10), and coupled cluster theory (CC) (Pub. 9).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Progress Summary: 12-Month Compression Set and Load Retention of Thermally Accelerated Aged Siloxane Specimens (Additively Manufactured by the Direct-Ink-Write (DIW) 3D Printing Technique) Was Measured

Motivation: Accelerated aging of polymeric materials is needed to predict their long-term mechanical functionality. Two key metrics used to evaluate their performance are compression set and load retention. A baseline(time=0)mechanical assessment was done prior to initiating the accelerated aging process to acquire initial thickness and load values for future calculation of compression set and load retention.Specimens are beingaged under compressive strain (13%for the current studies) at four different temperatures (25, 40, 55, and 70°C) for at least 1 year; compression set and load retention will be measured at various timepoints. Time-temperature superposition (TTS) will be applied to the isothermal data to obtain long-term predictions. Significance: Compression set is increasing with time and temperature, as expected. The increasing compression set is accompanied by decreasing load retention.The relativelylow compression set indicates the material is performing well.In a previous aging study, the legacy S5370 RTV foam exhibited 40% relative compression set after 12 months at 70°C, which is more than twice that of the DIW material. Progress:Data has been acquired out to the 12-month timepoint. Relative compression set and load retention versus time are shown in Fig. 1.A technical issue with the method of measuring load retention was discovered and previously reported load retention values have been adjusted; the current load retention values are estimates. TTS predictions are shown in Fig. 2.

36 MATERIALS SCIENCE↗

Measurement of Neutrino Absolute Deep Inelastic Scattering Cross Section in Iron, Lead, Carbon, and Plastic Using MINERvA Detector at $E_{\nu} = 6$ \GeV

A deep inelastic sample is selected from the nuclear charged current inclusive analysis, by requiring reconstructed $Q^{2} \geq 1.0$ (GeV/c)$^{2}$ and $W \geq 2.0$ GeV/c$^{2}$. The neutrino energy range of $5 < E_{\nu} < 50$ previously applied to this analysis in the Low Energy (LE) analysis is removed and the energy range cut is imposed on the muon energy from $2 < E_{\mu} < 50$ GeV. Machine learning vertexing is used to improve the track-based vertexing resulting in higher purity and efficiency of the sample. A local sideband method is utilized to remove the plastic background for the events reconstructed in the target. After plastic backgrounds and non-DIS backgrounds are subtracted, the reconstructed neutrino energy and Bjorken-x are unsmeared to their true quantities via Bayesian unfolding. The unfolded distributions of carbon, iron, lead, and plastic are efficiency corrected and then divided by the flux and the number of nucleons in the target to produce the absolute cr oss section as a function of $E_{\nu}$ and differential cross section as function of $x_{bj}$. The results of the analysis show good agreement between data and MC for $E_{\nu}$ and $x_{bj}$ (see Figures \ref{fig:xsecEnuC} through \ref{fig:xsecXCH}). None of the distributions displayed significant differences with the theoretical models underlying MINERvAs MC.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Functional Photoresists for Energy Applications. Final Report

Monolithic ultralow-density porous bulk materials have recently attracted much interest due to many emerging applications in the areas of catalysis, energy storage and conversion, and thermal insulation. They are also important components of high energy density (HED) and inertial confinement fusion (ICF) targets. However, despite tremendous progress that has been made in the synthesis of porous materials, deterministic and independent control over microscopic architecture, density and composition remain key issues, and their integration in high precision devices requires cost and time-intensive mechanical machining that not only reduces reproducibility by generating debris but also limits the complexity of the 3D shapes that can be realized. In this project, we overcame these limitations by developing a universal templating capability that provides deterministic and independent control over density, composition, architecture, and macroscopic sample shape. This was achieved by developing the technology to 1) 3D print ultrahigh resolution, ultra-high precision polymeric micro-lattice templates, 2) coat these templates with the desired materials, and 3) removing the template (Fig. 1a). Atomic layer deposition (ALD) provides the atomic scale coating thickness accuracy required for precisely controlling density. While this templating approach had been demonstrated in prior work, limitations in suitable photoresists, 3D print technologies, print design, and template removal techniques did not allow the fabrication of millimeter-sized high-precision parts with sub-micron resolution. To enable this technology, we developed 1) two-photon polymerization (TPP) print designs that enable the fabrication of millimeter-sized, mechanically robust polymeric templates with sub-micron resolution and 2) a continuum level TPP printing simulation capability for additional print design guidance; 3) atomistic models to study photoresist polymerization kinetics and network topography, 4) refractive index matched polymeric and preceramic TPP photoresists, and 5) functional TPP photoresists including porous voxel structures and self-immolative polymer photoresist chemistries; and 6) damage free template removal techniques that enable the fabrication of defect-free high-precision low-density foam components. We also developed a templating approach for pure carbon microlattices with a unique tube-in-tube ligament morphology. As a test platform, we pursued the fabrication of foam liners that promise to further increase the neutron yield in indirect drive ICF experiments by improving implosion symmetry control and coupling between the laser and the deuterium-tritium fuel. This application requires fabrication and integration of a ultra-high precision, millimeter-sized, thin-walled (200-400 micrometer thick), low-density (10-30 mg/cc), high atomic number (high Z) cylindrical foam tube into the gold hohlraum of an indirect drive ICF target (Fig. 1b). While our hohlraum liner test case will mainly find application in HED and ICF experiments, the underlying science will also directly apply to previously developed nanoparticle and additive manufacturing technologies and will advance those techniques as well.

36 MATERIALS SCIENCE↗

Self-Assembly and Phase Separation for Transport: A brief argument for the continued exploration of liquid crystal flows and electrodeposition in micro-gravity

Phase separation, interfacial tension gradients, and molecular self-assembly are all phenomena frequently observed when manipulating soft condensed matter systems on Earth. Depending on the system these processes can also be quite predictable. For instance, on Earth water droplets placed on hydrophobic surfaces will have contact angles > 90° with limited spread, contrary to their wetting behavior on hydrophilic surfaces. However, in an environment that is in a constant state of free-fall, where the gravitational field is reduced by 10%, such as on the International Space Station (ISS), buoyancy and its effect on fluid convection also become negligible. Fluid flow and phase behavior become less predictable. Thus, continuing the prior example, even if water droplets still remain in contact with a surface in microgravity (µg), the interface between the air and droplets will still remain significantly curved, appearing almost as if they were placed over completely nonwetting surfaces (Fig. 1a). Moreover, the negligible opposing buoyant force would also mean that if immiscible liquid droplets of a less dense character, or air bubbles even (Fig. 1b), were to be suspended within a larger water drop, these immiscible droplets or air bubbles would not migrate toward any one direction unless either artificially propelled by an external force or internal reaction inducing flow.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fission Product Evaluation (Quarterly Report)

The LLNL team has developed a theoretical framework to compute the fission fragment charge and mass distributions of odd-mass nuclei, which can be formed in neutron-induced reactions on even-even nuclei. For example, n+ 238 U leads to the compound nucleus 239 U which has 147 neutrons. Odd-mass and odd-odd nuclei are spin-polarized: the spin of the nucleus is not equal to 0 as in even-even nuclei (a consequence of pairing correlations) but is in fact set by a single particle. In practice, that single particle can occupy different quantum-mechanical configurations, each with different spin. This affects the deformation properties of the nucleus and, as a result, the distribution of fission fragments. These distributions require two inputs for the calculation: a potential energy surface (= the total energy of the nucleus as a function of the deformation of the nuclear shape, often parametrized with 2 degrees of freedom) and the collective inertia tensor associated with each point of the PES. In an odd-mass or odd-odd nucleus, each quantity depends on the configuration of the single particle. We computed of the order of 20 to 30 different such configurations to extract the PES for spins K=1/2, 3/2, 5/2, 7/2, and 9/2 of 239 U. We then computed the primary yields for each such PES, as shown in Fig. 1 below. These yields were weighed with the spin distribution associated with the reaction 238 U+n and the resulting distribution used as input to FREYA to compute the independent yields shown in Fig. 2. These yields are then used as inputs to the FIER code to extract the cumulative yields and compare with LLNL-LANL measurements at TUNL.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Hardtack I

After thirty-four tests, Hardtack I came to an end on August 18, 1958, with the thirty-fifth and final test, Fig. Four days later, President Dwight Eisenhower told Norris Bradbury, “I am today announcing that the United States will suspend nuclear weapons tests for a period of twelve months and, under certain conditions of progress toward real disarmament, continue that suspension on a year-to-year basis.”1 Although not intended, Eisenhower’s announcement made Fig the last nuclear test conducted in the Marshall Islands.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Influence of Vegetation Canopy Architecture on Dynamics of Spatiotemporal Light Distribution and its Effect on Land-Biosphere-Atmosphere Fluxes of Energy, Carbon, and Water

The dynamic spatiotemporal distribution of light and micro climatic variables (wind speed, atmospheric CO 2 concentration, humidity, pressure, and air temperature) within the plant canopy as determined by the canopy architecture play a critical role in land-biosphere-atmosphere (LBA) photosynthetic carbon uptake, transpiratory water loss and energy partitioning. Vegetation models that include effects of sun and shade flecks, leaf temperature and energy balance partitioning between sensible and latent heat fluxes, and reduced turbulent mixing in dense vegetation canopies can accurately predict canopy performance, particularly its shaded leaves, which can constitute 80% of leaf area and contribute up to 50% of carbon update and 65% of water loss. However, current vegetation models with their bulk characterization of shaded leaves poorly represent the complex three dimensional (3D) canopy architecture are insufficient to capture the spatiotemporal dynamics of shaded leaves. Here, we propose to employ an x-ray computed tomography (XCT) imaging technique in combination with an automated, high throughput, image processing pipeline (3DArch, to be developed) to obtain an explicit 3D triangulated surface mesh of a plant canopy (Fig 1). 3DArch would provide a much needed technological jump in 3D LBA modeling where computer generated artificial 3D models suffer from lack of high resolution detailed canopy architecture parameters. The 3D canopy surface mesh output from 3DArch is coupled with an explicit 3D forward ray tracing model (fastTracer) to obtain a high resolution representation of the dynamic spatiotemporal light environment within the canopy over the course of a day (Fig 1). The results from the light attenuation model are then coupled with a process based multi-scale bio-physical canopy and leaf model of photosynthesis (PlantGro) to get fluxes of carbon, water and energy at the leaf and canopy scale, in addition to estimating whole plant carbon uptake, and water loss. Our proposed model framework would be the first of its kind to provide a breakthrough capability in the field of process-based plant modeling that bridges the key technological gap in shaded leaf modeling through explicit representation of 3D canopy architecture. Computer generated artificial 3D model canopy simulations on grasses show that the canopy light distribution does not follow an exponential behavior as assumed in most 1D vegetation models, but rather exhibits a heterogeneous behavior, with a small but significant portion of interior canopy leaves experiencing peak light levels due to sun flecks while the rest of the canopy receives substantially lower light levels. These results indicate a bias in traditional models that overestimates shaded leaf contribution towards whole canopy photosynthesis by up to 15% and underestimate transpiration by up to 12% with an associated increase in sensible heat fluxes since photosynthesis, transpiration and energy partitioning are tightly coupled processes. However, these test results need to be validated using the 3D architecture obtained from a real plant imaged in 3D using 3DArch, rather than an artificial model plant. Our proposed model framework would allow us to identify inefficiencies in canopy light distribution and prescribe optimal canopy architectures (leaf optical properties, leaf area, leaf angles, row spacing, planting density, etc.) to traditional and genetic engineering based crop breeders, for maximizing target functions such as light use efficiency, water use efficiency, drought tolerance, crop yield, crop resilience etc., with important applications in biofuel crops such as sorghum, and switchgrass. Our model can also be applied for designing optimal canopy architecture that increase surface albedo as a mitigation strategy for global warming and projections of crop yield for future food and water security under climate change.

59 BASIC BIOLOGICAL SCIENCES↗

Assessment of the quality of nuclear data for stable oxygen isotopes for Intentional Forensics applications

The Intentional Forensics (IF) project seeks to design a suite of tagging materials that can be used to unobtrusively “barcode” nuclear fuel. The idea being that, if the fuel leaves institutional controls and is later recovered, the “barcode” can be used to determine the provenance of the fuel. The IF project is investigating several schemes for this “barcode” and taggants with tailored isotopic compositions are once leading concept. Recently 18 O was suggested as a potential taggant [IF2023]. This report assesses the quality of 16,17,18 O evaluations in the ENDF/B-VIII.0 library [ENDF8.0]. In a neutron-rich environment such as a nuclear reactor, we are interested in two main processes – neutron scattering and neutron absorption (or capture). For the typical neutron energies encountered in a reactor, absorption is determined exclusively by the neutron radiative capture cross section (in which a neutron is absorbed, and the residual nucleus emits one or more gamma rays). The capture cross sections are described by and can be completely determined from R-matrix parameters in the ENDF evaluations. Therefore, it is sufficient to consider the quality of the neutron resonance part of these evaluations. Neutron scattering is determined mainly by the elastic scattering cross section which is very similar for all oxygen isotopes and is essentially constant until around 100 keV. The cross section varies from 3-4 barns, depending on the isotope, and 16 O has the largest elastic cross section of all isotopes. Therefore, we expect that significant amounts of 17 O and 18 O could diminish the moderating role of oxygen in fuel. We note that, in traditional power reactor, the hydrogen in the coolant water provides the vast majority of the moderation in the reactor, so the impact of 17 O and 18 O in any taggant would be minimal. At higher energies, neutron resonances start to play a role and the R-matrix parameters determine the cross sections. Fig. 1 shows the mass region near stable oxygen isotopes. As nuclei capture neutrons, they transmute into a different isotope, one unit to the right. In particular, 16 O transmutes to 17 O, 17 O transmutes to 18 O and 18 O transmutes to 19 O. 19 O, being unstable, beta decays in 27 s to 19 F. So, even if the 18 O neutron capture data is good, the fact that it transmutes into 19 F may be problematic and needs investigation. Fig. 2 from [NuDat] shows the thermal neutron capture cross sections for all nuclei in the ENDF/B-VII.1 library [ENDF7.1]. Clearly oxygen thermal capture values are quite small compared to other nuclei. Note, there is no 18 O evaluation in the ENDF/B-VII.1 library. In any event, given that neutron capture events lower the reactor reactivity and potentially induce chemical changes in the fuel, we will focus our attention on the capture part of the neutron resonances.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Load Test of Alum-a-Lift Serial No. 33053261

An Alum-A-Lift A800CSPD-60 (Lift) was procured to support mechanical testing of programmatic equipment. This testing will take place within the Bldg. 131 Hi Bay. The design of the Lift procured for the purposes at LLNL was a modification of a machine that had previously been engineered and sold by Alum-a-Lift, see Fig. 1. The modification was to shorten the boom from a 56 in. length to a 28 in. length. The modified design is illustrated in Fig. 2. The Lift was fabricated and shipped to LLNL, received ~ June 2022. Upon arrival, it was successfully evaluated for “no-load” performance capability. Upon inspection of the documentation provided by Alum-a-Lift, it was noted that the load test was performed to qualify the machine for a lifting capacity of 200 lb. The LLNL requirement was that the capacity of the machine be 400 lb. Conversations with the vendor, Alum-A-Lift, followed this discovery. Rather than send the machine back to the vendor for load testing, discussions concurred that LLNL would load test the machine and Alum-A-Lift would provide the relevant load test placard to be placed on the machine subsequent to the successful load test. This MESN provides documentation of the load test to qualify the Alum-a-Lift to its’ rated capacity of 400 lb.

42 ENGINEERING↗

Machine learning assisted prediction of tungsten heavy alloy plasma facing component performance for fusion energy applications

Tungsten and tungsten heavy alloys (WHAs), known for their remarkably high hardness, durability, and corrosion resistance, play a critical role in the thriving development of nuclear fusion reactors in recent years. However, the exploration in tungsten alloys for the nuclear-related applications has been limited by the difficulty of manufacturing and the complexity of experiments to reproduce the environment of nuclear reaction. Therefore, this project aims to utilize nanoscale simulation methods such as density functional theory (DFT) and molecular dynamics (MD) with the help of machine learning techniques to not only understand the mechanisms of tungsten alloys but also allow us to computationally predict their mechanical behaviors under extreme environments. One critical problem of the application of WHAs in nuclear reactors is the surface melting. In the current design of the SPARC reactor, the WHA, W97Ni2.1Fe0.9 or W97NiFe, is chosen to be the first wall components to confine the plasma where the particles are fiercely moving and colliding into each other to create nuclear fusion reaction. This process will generate extremely high heat flux onto these WHA tiles, leaving high surface temperature that could possibly melt the surface of the WHA tiles, As illustrated in Fig. 1(a). a laser experiment previously done illustrates that a rough surface damage would be made after the surface melting where the matrix area mainly composed of nickel and iron as shown in Fig. 1(b), will first melt and then leave vacancies between these tungsten grains. Unfortunately, these kinds of roughness on the first-wall components could be deadly to the plasma inside a Tokmak reactor because the heat that is supposed to dissipate at a designed ratio through the tiles may in turn be excessively absorbed and accumulated on any uneven area of the surface, which will eventually make the whole nuclear reaction fail. In this project, we will introduce a machine learning potential, Allegro, based on DFT calculation and then build a MD model for W-Ni-Fe alloys.

36 MATERIALS SCIENCE↗