SEARCH · Engineering Papers

Results for “Electric Machine”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Rotor Magnet Fault Analysis in Permanent Magnet AC Machines Under Load Conditions - All Electric Transportation Systems

This paper studies the performance of a Permanent Magnet (PM) alternating-current (AC) machine when subjected to faults under load conditions. The effect of varying load torques, and unbalances are found to be potential causes of rotor faults, inducing physical magnet defects or broken rotor-PMs. The consequent and immediate impact on the machine quantities is observed through anomalous change in torque-speed characteristics and other vital signatures such as machine back-EMF/flux and motor current signatures (MCS). The present research study develops and illustrates a method to diagnose physical magnet defects (fault) in PMAC machines by estimating the machine torque/back-EMF constant, Ke. The constant Ke is a measure of magnet strength exhibiting the health of rotor PMs, indicative of faults. Advanced research studies and investigations are carried out to establish motor approximations and signature-based analysis as significant viable tools for diagnosing machine faults even under load conditions.

alternating current↗

DOE OSTI2023

Root Cause Analysis of Degradation in Protonic Ceramic Electrochemical Cell with Interfacial Electrical Sensors Using Data‐Driven Machine Learning

Abstract Protonic ceramic electrochemical cells (PCECs) offer promising paths for energy storage and conversion. Despite considerable achievements made, PCECs still face challenges such as physiochemical compatibility between componenets and suboptimal solid–solid contact at the interfaces between the electrolytes and electrodes. In this study, a novel approach is proposed that combines in situ electrochemical characterization of interfacial electrical sensor embedded PCECs and machine learning to quantify the contributions of different cell components to total degradation, as well as to predict the remaining useful life. The experimental results suggest that the overpotential induced by the oxygen electrode is 48% less than that of oxygen electrode/electrolyte interfacial contact for up to 1171 h. The data‐driven machine learning simulation predicts the RUL of up to 2132 h. The root cause of degradation is overpotential increase induced by oxygen electrode, which accounts for 82.9% of total cell degradation. The success of the failure diagnostic model is demonstrated by its consistency with degradation modes that do not manifest in electrolysis fade during early real operations. This synergistic approach provides valuable insights into practical failure diagnosis of PCECs and has the potential to revolutionize their development by enabling improved performance prediction and material selection for enhanced durability and efficiency.

25 ENERGY STORAGE↗

DOE OSTI2020

2019 Vehicle Technologies Office Annual Merit Review Report

The 2019 U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy’s (EERE) Vehicle Technologies Office (VTO) Annual Merit Review (AMR) was held June 10-13, 2019, in Arlington, Virginia. The review encompassed work done by VTO: 287 individual activities were reviewed by 272 reviewers. Exactly 1,162 individual review responses were received for the VTO technical reviews. The objective of the meeting was to review the accomplishments and plans for VTO over the previous 12 months, and provide an opportunity for industry, government, and academia to give inputs to DOE on the Office with a structured and formal methodology. The meeting also provided attendees with a forum for interaction and technology information transfer.

03 NATURAL GAS↗

DOE OSTI2022

Electrostatic energy harvester

An electrostatic energy harvester broadly comprises an electrical energy storage component, an electrical energy transfer stage, first and second variable capacitors, and a switching control module. The electrical energy transfer stage includes diode-connected transistors and dictates electrical energy transfer between the electrical energy storage component and the variable capacitors. The switching control module timely switches between the first and second variable capacitors according to a state machine. Subsequent electrical energy investments from the electrical energy storage component are less than an initial electrical energy investment due to remnant electrical energy remaining at the previously active one of the first and second variable capacitors from previous electrical energy harvesting.

Wilson, Amy Charlene↗

DOE OSTI2022

Electrostatic energy harvester

Wilson, Amy Charlene↗

DOE OSTI2022

Electrostatic energy harvester

Wilson, Amy Charlene↗

DOE OSTI2025

Machine learning of 27Al NMR electric field gradient tensors for crystalline structures from DFT

NMR crystallography has emerged as a promising technique for the determination and refinement of atomic coordinates in crystal structures. The crystal structure of compounds containing quadrupolar nuclei, such as 27Al, can be improved by directly comparing solid-state NMR measurements to DFT computations of the electric field gradient (EFG) tensor. The non-negligible computational cost of these first-principles calculations limits the applicability of this method to all but the most well-defined structures. We developed a fast, low-cost machine learning model to predict EFG parameters based on local structural motifs and elemental parameters. We computed 8081 EFG tensors from 1681 27Al crystalline solids using DFT and benchmarked them against 105 experimentally measured 27Al sites. Surprisingly, simple local geometric features dominate the predictive performance of the resulting random-forest model, yielding an R2 value of 0.98 and an RMSE of 0.61 MHz for CQ, the quadrupolar coupling constant. This model accuracy should enable pre-refining future structural assignments before finally validating with first-principles calculations. Such a catalogue of 27Al NMR tensors can serve as a tool for researchers assigning complex NMR spectra influenced by the nuclear electric quadrupole interaction.

Sun, He↗

DOE OSTI2020

A High-Speed High-Power-Density Non-Heavy Rare-Earth Permanent Magnet Traction Motor

There has been a global push for higher torque density and lower cost traction motors. The use of non-heavy rare-earth (non-HRE) permanent magnet materials in traction motors are being investigated for the sustainability, profitability and affordability of electric vehicles and to broaden their adoption. A 20,000-rpm permanent magnet traction motor using non-HRE magnet materials is proposed. A dual three-phase winding configuration driven by a segmented dual three-phase drive is proposed to reduce the current ripple, and as a result, the DC Link capacitor, as well as to ease the voltage constraint at high speed and eliminate any risk of uncontrolled regeneration. Furthermore, the dual winding configuration enables a fault tolerant design which is useful for reliability. The paper presents comprehensive electromagnetic, thermal and mechanical designs and analyses using an integrated approach. The results have shown that the design is robust against demagnetization and confirmed its thermal and mechanical viability.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

A Global Perspective on Supercomputer Power Provisioning: Case Studies from United States and Europe

Electrical provisioning in high performance computing is transitioning from simple nameplate Thermal Design Power (TDP) models to more nuanced approaches based on expected electrical load. This paper captures current power provisioning strategies across six international supercomputing centers and seven systems, three of which (Lumi, Summit, Sierra) were in the top 10 of the Top500 list at the time of data collection1. We present longitudinal and summary data of actual power consumption as well as a discussion of how each site approached the question of provisioning. We conclude with a discussion on future directions of hardware overprovisioning and its implications for machine and electrical utilization.

Patki, Tapasya [Lawrence Livermore National Labora↗

DOE OSTI2024

IASCC of 304 SS in BWR environments: Effects of post-irradiation annealing and surface condition

To investigate the impact of low-temperature post-irradiation annealing (PIA) on the stress corrosion cracking of neutron-irradiated 304 stainless steel, constant extension rate tests were conducted in simulated boiling water reactor normal water chemistry (BWR-NWC) and hydrogenated water chemistry (HWC) environments. Ten tensile samples, comprising five as-irradiated and five PIA specimens, were prepared by electropolishing the gauge section of electric discharge machined (EDM) samples. Here, the annealing treatment reduced the yield strength from approximately 550 MPa to around 425 MPa and significantly restored the ductility and the strain hardening capability of the alloy. Consequently, the susceptibility of this material to irradiation-assisted stress corrosion cracking (IASCC) was effectively mitigated, which is more prominent in HWC, as evident from fractography, which indicated a decreased propensity for intergranular (IG) fracture. Furthermore, it was observed that the polished surface facilitated crack initiation more readily than the EDM surface, suggesting that the EDM process suppressed crack initiation to some extent.

Crack initiation↗

DOE OSTI2025

Solution‐Phase Metathesis of Li 3 N and FeCl 3 to Synthesize Fe 2 N/Fe 3 N Nanoparticles

Soft magnetic materials play key roles in the flow of energy in electrically driven machines and power conversion electronics, and there is a great need for improvements in their magnetic properties to provide the right combination of high saturation magnetization, low coercivity, and high permeability. Most phases of iron nitride (Fe x N) are soft magnetic materials with these characteristics, but they exist as numerous phases which are not all stoichiometric compounds. While the production and magnetic properties of the different phases of bulk iron nitride are well known, accessing phase‐pure nanoscale iron nitride consistently remains a challenge. Most methods for the synthesis of iron nitride nanoparticles require complicated apparatus to achieve high‐temperature nitriding of nanoparticle precursors with gaseous nitrogen sources such as ammonia. The first solution‐phase metathesis reaction between FeCl 3 and Li 3 N in oleylamine is developed to directly synthesize Fe 2 N/Fe 3 N nanoparticles, requiring only a fume hood, glove box, standard chemistry laboratory glassware, and equipment. Finally, the ≈10–15 nm spheres display nearly soft magnetic behavior with a saturation magnetization ≈50–60 A m 2 kg −1 , coercivities between 40–50 kA m −1 , and susceptibility values from 0.0001–0.0006 m 3 kg −1 , well within the ranges reported with other published Fe x N nanoparticle synthesis methods.

iron nitride↗

DOE OSTI2022

Residual Stress Measurements in Extreme Environments for Hazardous, Layered Specimens

In nuclear fuel plates of low-enriched U-10Mo (LEU) clad with aluminum by hot isostatic pressing (HIP), post-irradiation stresses arising during reactor shutdown are a major concern for safe reactor operations. Measurement of those residual stresses has not previously been possible because the high radioactivity of the plates requires handling only by remote manipulation in a hot cell. The incremental slitting method for measuring through-thickness stress profiles was modified, and a system for automated, remote operation was built and tested. Experimental modifications consisted of replacing electric-discharge machining (EDM) with a small end mill and strain-gauge measurements with cantilever displacement measurements. The inverse method used to calculate stresses was the pulse-regularization method modified to allow discontinuities across material interfaces. The new system was validated by comparing with conventional slitting on a depleted U-10Mo (DU) fuel plate. The new system was applied to two measurements each on six as-fabricated (pre-irradiation) LEU miniature fuel plates. Variations between the measurements at two locations in the same plate were strongly correlated with measured geometrical heterogeneity in the plate—a tilt in the fuel foil. Compressive stresses in the U-10Mo were shown to increase from 20 to 250 MPa as the ratio of aluminum thickness to U-10Mo thickness increased causing increased constraint during cooling. Faster cooling rates during processing also increased stress magnitudes. The measurements trends agreed with data in the literature from similar plates made with DU, which further validates the method. Because other methods are impractical in a hot cell, the modified slitting method is now poised for the first measurements of post-irradiation stresses.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗

DOE OSTI2023

Numerical Simulations of High Prandtl Number Liquid Jets Impinging on a Flat Plate

In this work, 3D simulations of oil jets impinging on a flat, heated wall are presented. The numerical setup uses the Volume of Fluid (VoF) method to model the two-phase flow. A careful grid definition across the liquid film, along with the use of the Conjugate Heat Transfer (CHT) approach allowed local heat transfer to be solved with fine resolution at the wall. Variations of liquid flow rate, liquid temperature and surface temperature allow to cover a wide range of local Reynolds and Prandtl numbers (226 < Re < 2850, 77 < Pr < 161). Resulting surface-averaged heat transfer compares very well with experimental measurements conducted in a previous study. In-depth analysis of the flow has identified expected features from the literature. In particular, the impact of jet axial velocity profiles on the heat transfer distribution in the stagnation zone was clearly stated. The increase in heat transfer when warming the liquid film was also reproduced and explained by a decrease in oil viscosity and an increase in film velocity. All those effects were taken into account in correlations for stagnation and local values of Nusselt number. A grid sensitivity study was also conducted, showing that if the grid solving the thermal boundary layer in the stagnation zone can be coarsened without impacting local and surface-averaged predictions of heat transfer, a minimum resolution (2 to 3 cells) within the thermal boundary layer is however required for an accurate prediction of heat transfer.

conjugate heat transfer↗

DOE OSTI2023

A multi-length-scale investigation of the applicability of ductility laws for annealed and work-hardened copper

Small-scale mechanical testing provides unique advantages over conventional testing in investigating the mechanical response of nuclear materials. While small-scale testing enables accelerated materials research, it raises the question of comparability to large-scale properties for engineering design considerations. Among different mechanical properties for structural design considerations such as yield and ultimate tensile stress, ductility is of critical importance with respect to structural component health. The effectiveness of using small-scale mechanical testing for probing these mechanical properties is dictated by understanding how the mechanical responses translate from the microscale to the engineering scale. Therefore, a better understanding of size scaling effects via gathering and analysis of experimental data is required to bridge length-scales. Further, this work builds upon previous reports to provide statistical data on how mechanical response changes as the size of the specimens are reduced from conventional sizes. One hundred twenty mesoscale tensile coupons of oxygen-free high thermal conductivity (OFHC) copper in work-hardened and annealed state have been manufactured using micro-wire electrical discharge machining (EDM) and tested under uniaxial tension. The mesoscale specimens have dimensions dictated by pre-selected geometric ratios (i.e., gauge section length over the square root of the cross-section area) with gauge length dimensions of 3 mm (or less) and sub-millimeter gauge widths and thicknesses. The mesoscale responses were compared to bulkscale properties to reveal the effect of specimen size on the mechanical response as a function of grain size and material state for a single phase face-centered cubic metal.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Motorette Thermal Performance Testing and Modeling for an Electric Motor with Additively Manufactured Hollow Conductors with Integrated Heat Pipes

This paper discusses the design, build and test of a motorette to characterize the thermal performance of an additively manufactured coil integrated with heat pipes. The motorette is powered using a variable frequency AC power supply and cooled through two independent cooling systems. The first cooling system cools the stator core using forced convection of air flowing over a finned heat sink mounted on the stator outer diameter. The second cooling system cools the heat pipes using forced convection of 50-50 water ethylene glycol (WEG) mixture flowing through condenser chambers. A 3D thermal FEA model of the setup is built and heat transfer coefficients (HTC) of convective boundaries are computed using coolant flow rates from test data and empirical equations. Temperature at locations on the coil and heat sink are recorded and compared to thermal model predicted values. A maximum temperature error of 22.7% occurs at 180ARMS and 800 Hz operating point for the AM dual coil. The thermal model provides higher temperatures compared to test results and hence it is on the conservative side but in general, there is good correlation between test and model results. Lastly, opportunities for improvement to both test data measurement and 3D thermal FEA modeling are discussed.

additive manufacturing↗

DOE OSTI2023

Cooling Strategies for an Electric Motor with Additively Manufactured Hollow Conductors and Distributed Power Electronics Integrated with Heat Pipes

This paper discusses design tradeoffs and thermal modeling explored in cooling strategies for an aircraft propulsion electric motor with additively manufactured coils and distributed power electronics integrated with heat pipes. Design tradeoffs include heat pipe Qmax performance related to inclination, condenser configuration, coolant type, coolant flow path complexity, and ease of access to modular power electronics. Three cooling strategies were selected and realized into CAD models. These models were further evaluated using 3D thermal FEA and optimization tools to explore cooling geometry details that include fin thickness, spacing and count with the objective to minimize fin mass under a set of constraints. Lastly, motorette test data is presented comparing air versus liquid cooling of heat pipes.

additive manufacturing↗

DOE OSTI2021

A Cooperative Game Theory-based Approach to Under-frequency Load Shedding Control

This paper proposes a cooperative game theory-based under-frequency load shedding (UFLS) approach for frequency stability and control in power systems. UFLS is a crucial factor for frequency stability and control especially in power grids with high penetration of renewable energy sources and restructured power systems. Conventional UFLS methods, most of which are off-line, usually shed fixed amounts of predetermined loads based on a predetermined schedule which can lead to over or under curtailment of load. This paper presents a co-operative game theory-based two-stage strategy to effectively and precisely determine locations and amounts of loads to be shed for UFLS control. In the first stage, the total amount of loads to be shed, also referred to as deficit in generation or the disturbance power, is computed using the initial rate of change of frequency (ROCOF) referred to the equivalent inertial center. In the second stage, the Shapley value, one of the solution concepts of cooperative game theory, is used to determine load shedding amounts and locations. The proposed method is implemented on the reduced 9-bus 3-machine Western Electricity Coordinating Council (WECC) system and simulated on Real-time Digital Simulators (RTDS). The results show that the proposed UFLS approach can effectively return the system to normal state after disturbances.

42 ENGINEERING↗