Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXTRUSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Manufacture of porous biodegradable polymer conduits by an extrusion process for guided tissue regeneration

We have fabricated porous, biodegradable tubular conduits for guided tissue regeneration using a combined solvent casting and extrusion technique. The biodegradable polymers used in this study were poly(DL-lactic-co-glycolic acid) (PLGA) and poly(L-lactic acid) (PLLA). A polymer/salt composite was first prepared by a solvent casting process. After drying, the composite was extruded to form a tubular construct. The salt particles in the construct were then leached out leaving a conduit with an open-pore structure. PLGA was studied as a model polymer to analyze the effects of salt weight fraction, salt particle size, and processing temperature on porosity and pore size of the extruded conduits. The porosity and pore size were found to increase with increasing salt weight fraction. Increasing the salt particle size increased the pore diameter but did not affect the porosity. High extrusion temperatures decreased the pore diameter without altering the porosity. Greater decrease in molecular weight was observed for conduits manufactured at higher temperatures. The mechanical properties of both PLGA and PLLA conduits were tested after degradation in vitro for up to 8 weeks. The modulus and failure strength of PLLA conduits were approximately 10 times higher than those of PLGA conduits. Failure strain was similar for both conduits. After degradation for 8 weeks, the molecular weights of the PLGA and PLLA conduits decreased to 38% and 43% of the initial values, respectively. However, both conduits maintained their shape and did not collapse. The PLGA also remained amorphous throughout the time course, while the crystallinity of PLLA increased from 5.2% to 11.5%. The potential of seeding the conduits with cells for transplantation or with biodegradable polymer microparticles for drug delivery was also tested with dyed microspheres. These porous tubular structures hold great promise for the regeneration of tissues which require tubular scaffolds such as peripheral nerve, long bone, intestine, or blood vessel.

NASA Discipline Cell Biology↗
NASA NTRS2017

Predictive Modeling of Fast-Curing Thermosets in Nozzle-Based Extrusion

This work presents an approach to modeling the dynamic spreading and curing behavior of thermosets in nozzle-based extrusions. Thermosets cover a wide range of materials, some of which permit low-temperature processing with subsequent high-temperature and high-strength working properties. Extruding thermosets may overcome the limited working temperatures and strengths of conventional thermoplastic materials used in additive manufacturing. This project aims to produce technology for the fabrication of thermoset-based structures leveraging advances made in nozzle-based extrusion, such as fused deposition modeling (FDM), material jetting, and direct writing. Understanding the synergistic interactions between spreading and fast curing of extruded thermosetting materials will provide essential insights for applications that require accurate dimensional controls, such as additive manufacturing [1], [2] and centrifugal coating/forming [3]. Two types of thermally curing thermosets -- one being a soft silicone (Ecoflex 0050) and the other being a toughened epoxy (G/Flex) -- served as the test materials in this work to obtain models for cure kinetics and viscosity. The developed models align with extensive measurements made with differential scanning calorimetry (DSC) and rheology. DSC monitors the change in the heat of reaction, which reflects the rate and degree of cure at different crosslinking stages. Rheology measures the change in complex viscosity, shear moduli, yield stress, and other properties dictated by chemical composition. By combining DSC and rheological measurements, it is possible to establish a set of models profiling the cure kinetics and chemorheology without prior knowledge of chemical composition, which is usually necessary for sophisticated mechanistic modeling. In this work, we conducted both isothermal and dynamic measurements with both DSC and rheology. With the developed models, numerical simulations yielded predictions of diameter and height of droplets, along with width and height of extruded lines cured at varied temperatures. Experimental results carried out on a goniometric platform and a nozzle-based 3D printer showed agreement with the numerical simulations. Finally, this presentation will show how the models are adaptable to the planning of tool paths and designs in additive manufacturing.

Xie, Jingjin↗
DOE OSTI2018

Parametric Analysis on Vertical Pins for Strengthening Extrusion-Based Printed Parts

For extrusion-based additive manufacturing, the mechanical performance in vertical direction (z-direction) is significantly lower than that in the printed layer plane (xy-direction). This paper presents a vertical extrusion approach across several layers to improve the mechanical properties of a 3D printed part. This approach is patent pending, and it involves depositing pins in the z-direction into predefined holes. It requires the vertical pins to mechanically engage with the surrounding structure of the holes. To maximize the mechanical performance of the printed structures with pins, we then analyzed the penetration quality of the pins with a wide range of hole depths, hole sizes, and pin volumes and obtained the relationship between the hole width and the hole depth for the full penetration of pins.

Kim, Pum↗
DOE OSTI2022

THE IMPACT OF A STATIC-MIXING NOZZLE ON UNIFORMITY IN MATERIAL EXTRUSION LARGE-SCALE ADDITIVE MANUFACTURING

There are many methods of incorporating more than one material in Additive Manufacturing (AM) processes. Oak Ridge National Laboratory has developed a unique solution that enables in-situ material switching by developing a dual-hopper feed system for Cincinnati’s Big Area Additive Manufacturing (BAAM) system. Continuous extrusion during a step-change in material feedstock results in a unique blended material transition region that exhibits a heterogeneous internal morphology. To improve mixing of materials during extrusion, a customized static-mixing nozzle was created for use with the BAAM. Single-bead transitions from Material A to B and B to A were printed with the mixing nozzle at a specified screw speed. Compositional analysis tracked the progression of the material transition as a function of extrudate volume. The resulting transition curves were compared against a standard nozzle configuration. Optical microscopy of cross sections also demonstrated that the static-mixing nozzle promoted a more uniform bead geometry as well as a more homogeneous internal structure throughout the material transition.

Brackett, James↗
DOE OSTI2024

Toolpath considerations for extrusion: Pellet, filament, concrete, and thermoset

There are a variety of extrusion and deposition-based processes for additive manufacturing, such as fused deposition modeling (FDM), fused filament fabrication (FFF), and directed energy deposition (DED). These processes can use a variety of materials, including thermoplastic pellets, thermoplastic filament, thermoset, concrete, metal wire, metal powder, and more. For all these processes and materials, the underlying toolpath strategies for 3D-printing an object are the same: the object to be printed is sliced into layers, then the layer is optimally fit with toolpaths of a given width, based on specific user settings. However, based on the specific process being used, additional modifiers and toolpathing strategies may be employed to maximize the capabilities of the process and successfully construct an object. This chapter explores the different pathing considerations and additional strategies to be employed in extrusion processes that use thermoplastics, thermosets, and concretes.

Roschli, Alex↗
DOE OSTI2026

Ultrasonic-Assisted Extrusion Processing for Enhancing Physical Properties of High-Density Polyethylene by Flow-Induced Crystallization

The evolution of crystallinity resulting from stress imposed on a melt, known as flow-induced crystallinity, can strongly influence the mechanical and physical properties of semicrystalline polymers. This study investigates shear-induced crystallization by applying an ultrasonic field to the melt flow as it passes through dies with various geometries. A custom-built sonication die is employed for controlling the dynamic temperature and shear environment, resulting in molecular alignment and potential for flow-induced crystallization. Application of both conventional and ultrasonic shear rates at the equilibrium melt temperature of high-density polyethylene (HDPE) was investigated to accelerate crystallinity and manipulate the crystal morphology across the film in pursuit of improved mechanical and gas barrier properties without the need for additives or other polymer layers. The relationships among ultrasonic-assisted extrusion processing, polymer structure, and performance were analyzed using wide- and small-angle X-ray scattering (WAXS and SAXS), tensile testing, and oxygen transmission rate (OTR) analysis. Multiple linear regression models were implemented to predict the correlation among HDPE structure, process, and properties. Structural analysis revealed that both conventional and ultrasonic shear rates had the most significant influence on lamellar spacing and redistribution of rigid and soft amorphous fractions within the crystalline domains, ultimately dictating the mechanical and physical properties of the films. The goal is to explore the potential of the ultrasonic-assisted high crystallinity monolayer that can replace some of the functionality of complex, heterogeneous multilayer packaging with a single-material film having enhanced oxygen barrier properties.

crystallinity↗
DOE OSTI2021

Microstructure and Mechanical Properties of the AA7075 Tube Fabricated using Shear Assisted Processing and Extrusion (ShAPE)

Shear Assisted Processing and Extrusion (ShAPE) experimental setup and tooling were adopted for extruding thin-walled AA7075 aluminum tube from as-cast non-homogenized billet material in a single run. The mechanical and microstructural characterizations were performed on the extrudate in the as-extruded condition without subsequent heat treating. It was shown that the ShAPE process developed a significantly refined microstructure with uniform and almost equiaxed grain structure on both hoop and axial cross-sections of the extrudate as well as through the thickness of the material. The pole figures and inverse pole figures of the EBSD data showed an strong shear texture development, and it was found out that axial shear is the dominant deformation mechanism in the regions near the inner surface of the tube, while combined axial and torsional shears are the two dominant modes of deformation near the outer surface of the extrudate. As for the mechanical properties, there was an increase of 150% and 73% in the yield and ultimate strengths of the tube produced using ShAPE process, respectively, and a 18% decrease in maximum uniform plastic elongation compared to the conventionally extruded AA7075-O tube.

Shear Assisted Processing and Extrusion, Friction ↗
DOE OSTI2020

Mechanical Characterization of High-Temperature Carbon Fiber-Polyphenylene Sulfide Composites for Large Area Extrusion Deposition Additive Manufacturing

Additive manufacturing (AM) is evolving from rapid prototyping to production of structural components. The widespread application of AM demands a high level of mechanical performance from these components, and it is therefore essential to improve feedstock material in order to meet these mechanical expectations. However, compared to traditional manufacturing techniques, the mechanical properties of AM materials and their resulting components are not well understood. In this study, we investigated the processability, microstructure, and mechanical performance of twin-screw compounded short carbon fiber reinforced polyphenylene sulfide (PPS) pellets as a feedstock material for big area AM (BAAM). The performance of the AM components was compared to that of traditional processing methods, namely injection molding (IM) and extrusion-compression molding (ECM). It was found that the AM composites exhibited 118% lower tensile strength and 55% lower tensile modulus when compared to traditional injection molding composite specimens; however, AM composites exhibited comparable properties to ECM composites. This response was attributed to highly aligned fibers in IM and AM samples. However, the AM composites contained porosity (15.5% volume), which reduced their mechanical properties in comparison to ECM composites. Finally, the IM process showed the maximum amount of fiber attrition with minimum porosity (0.007% volume), while the ECM process exhibited the least fiber attrition with 4.3% volume porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrafine-grained Al-Mg-Zr Alloy Processed by Shear-Assisted Extrusion with High Thermal Stability

Shear-assisted processing and extrusion (ShAPE) is used to consolidate Al-4.2Mg-1.6Zr-0.25Si-0.1Fe (wt.%) powders. The extruded alloy exhibits: (i) near-zero porosity; (ii) an attractive combination of tensile yield strength (~220 MPa), ultimate strength (330 MPa) and elongation (>20%); and (iii) excellent thermal stability at 400 ºC. The ultra-fine grain size in the gas-atomized powders – created and stabilized by primary L12-Al3Zr submicron precipitates - is maintained after consolidation and subsequent exposure at 400 ºC, contributing twice as much to strength as Mg in solid-solution. Electron microscopy reveals the microstructure of the L12-Al3Zr precipitates, and other precipitates (Mg2Si and Al3Fe) and dispersoids (oxides).

ShAPE, Friction Extrusion, aluminum powder, Shear ↗
DOE OSTI2025

Material Extrusion Printing of Poly(Acrylonitrile‐Styrene‐Acrylate) and Poly(Acrylonitrile‐Butadiene‐Styrene) Structures Reinforced with Poly(Phenylene Oxide) Additives for Improved Thermomechanical Properties and their Surface Analysis by Time‐of‐Flight Secondary Ion Mass Spectrometry

Fused filament fabrication offers the ability to 3D print complex geometries made from plastic filament materials; however, these parts are mechanically outperformed by parts created by traditional fabrication methods. To overcome this challenge, a high-performance polymer poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) is incorporated as an additive into two common engineering thermoplastics, poly(acrylonitrile-styrene-acrylate) (ASA) and poly(acrylonitrile-butadiene-styrene) (ABS). Structures printed from these polymer blends are more mechanically robust compared to those prepared from the parent polymers, with low loading levels (1–5 wt%) of PPO improving the elastic strength by up to ≈30% relative to the parent terpolymers. Even at higher loading levels (10 and 20 wt% PPO), there is no evidence of additive aggregation in the model thin films, which is supported by compositional analysis of the copolymers and chemical analysis via time-of-flight secondary ion mass spectrometry. The enhancements in mechanical properties of ASA and ABS blends appear to be a consequence of homogeneous incorporation of the PPO additive. In conclusion, this work explores expanding materials-property space using miscible blends of engineering thermoplastics to improve mechanical performance as a general approach to overcoming challenges with parts created by melt-based material extrusion printing.

additive manufacturing↗
DOE OSTI2026

In-Process Melt Separation of Depolymerized PET in PET/PE Blends for Upcycling via Twin-Screw Extrusion

Our previous work focused on depolymerizing polyethylene terephthalate (PET) in twin-screw extrusion, as part of a broader project to continuously separate PET from polyolefins in the melt. This study focused on linear low-density polyethylene (LLDPE) and PET films and the use of ethylene glycol (EG), diethylene glycol (DEG), triethylene glycol (TEG), and bis(2-hydroxyethyl) terephthalate (BHET) to depolymerize the PET in the extruder to levels above 90% Mw. In this work, the focus will shift to achieving separation of the two polymers in the twin-screw extruder, which is made possible due to a 90% reduction in the Mw of the PET, which caused a decrease of its viscosity by several orders of magnitude. Owing to the viscosity difference and pressure buildup in the die, the low-viscosity PET preferentially exited a degassing vent instead of going through the die. This is because the flow of the PET would travel through a non-pressure vent rather than through a high-pressure die. However, owing to the higher viscosity of the LLDPE, the pressure was too high to pass through such a small diameter vent hole. Supercritical CO 2 (SCCO 2 ) was used to assist in this extraction, but SCCO 2 negatively impacted the overall degree of separation. Through analysis of the separated materials, it was concluded that a high separation of the two materials was achieved. TGA and FTIR confirmed that the material separated from the vent was 100% PET. The material removed from the die was composed of 95% LLDPE and 5% PET.

36 MATERIALS SCIENCE↗
DOE OSTI2026

In‐Process Melt Separation of PE/PET Blends for Upcycling via Twin‐Screw Extrusion. Impact of Catalyst Reagents on PET Depolymerization

Part 1 of this work focused on depolymerizing polyethylene terephthalate (PET) in twin-screw extrusion, as part of a broader project to continuously separate PET from polyolefins in the melt. This study focused on linear low-density polyethylene (LLDPE) and PET films and the use of ethylene glycol (EG), diethylene glycol (DEG), triethylene glycol (TEG), and bis(2-hydroxyethyl) terephthalate (BHET) to depolymerize the PET in the extruder to levels above 90% Mw. In part 2, the focus will shift to achieving separation of the two polymers in the twin-screw extruder, which is made possible due to a 90% reduction in the Mw of the PET, which caused a decrease of its viscosity by several orders of magnitude. Owing to the viscosity difference and pressure buildup in the die, the low-viscosity PET preferentially exited a degassing vent instead of going through the die. This is because the flow of the PET would travel through a non-pressure vent rather than through a high-pressure die. However, owing to the higher viscosity of the LLDPE, the pressure was too high to pass through such a small diameter vent hole. Supercritical CO₂ (SCCO₂) was used to assist in this extraction, but SCCO₂ negatively impacted the overall degree of separation. Through analysis of the separated materials, it was concluded that a very high separation of the two materials was achieved. TGA and FTIR confirmed that the material separated from the vent was 100% PET. The material removed from the die was composed of 90% LLDPE and 10% PET.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultrasound Manipulation and Extrusion of Active Nanorods

Abstract Synthetic self‐propelled nano and microparticles have a growing appeal for targeted drug delivery, collective functionality, and manipulation at the nanoscale. However, it is challenging to control their positions and orientations under confinement, e.g., in microchannels, nozzles, and microcapillaries. This study reports on the synergistic effect of acoustic and flow‐induced focusing in microfluidic nozzles. In a microchannel with a nozzle, the balance between the acoustophoretic forces and the fluid drag due to streaming flows generated by the acoustic field controls the microparticle's dynamics. This study manipulates the positions and orientations of dispersed particles and dense clusters inside the channel at a fixed frequency by tuning the acoustic intensity. The main findings are: first, this study successfully manipulates the positions and orientations of individual particles and dense clusters inside the channel at a fixed frequency by tuning the acoustic intensity. Second, when an external flow is applied, the acoustic field separates and selectively extrudes shape‐anisotropic passive particles and self‐propelled active nanorods. Finally, the observed phenomena are explained by multiphysics finite‐element modeling. The results shed light on the control and extrusion of active particles in confined geometries and enable applications for acoustic cargo (e.g., drug) delivery, particle injection, and additive manufacturing via printed self‐propelled active particles.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructural Evolution of Al-1Fe (Weight Percent) Alloy During Accumulative Continuous Extrusion Forming

As a new microstructure refining method, accumulative continuous extrusion forming (ACEF) cannot only refine metal matrix but also refine the phases that exist in it. In order to detect the refinements of grain and second phase during the process, Al-1Fe (wt pct) alloy was processed by ACEF, and the microstructural evolution was analyzed by electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Results revealed that the average grain size of Al-1Fe (wt pct) alloy decreased from 13 to 1.2 μm, and blocky Al{sub 3}Fe phase with an average length of 300 nm was granulated to Al{sub 3}Fe particle with an average diameter of 200 nm, after one pass of ACEF. Refinement of grain was attributed to continuous dynamic recrystallization (CDRX), and the granulation of Al{sub 3}Fe phase included the spheroidization resulting from deformation heat and the fragmentation caused by the coupling effects of strain and thermal effect. The spheroidization worked in almost the entire deformation process, while the fragmentation required strain accumulation. However, fragmentation contributed more than spheroidization. Al{sub 3}Fe particle stimulated the formation of substructure and retarded the migration of recrystallized grain boundary, but the effect of Al{sub 3}Fe phase on refinement of grain could only be determined by the contrastive investigation of Al-1Fe (wt pct) alloy and pure Al.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Spark Plasma Extrusion and the Thermal Barrier Concept

Spark plasma sintering (SPS) is currently a major powder consolidation process with many advantages; however, it is still largely limited to the processing of simple shapes such as discs due to its geometric restrictions. Alternatively, spark plasma extrusion (SPE) is a recently developed process that has superiority over SPS in terms of faster consolidation, generating products of extended geometries and potential grain refinement capabilities under applied current. So far, work on SPE has resulted in large temperature gradients within the extruding material with microstructural and properties in-homogeneities. The present paper reports on a novel approach (thermal barrier concept) that allows the SPE of materials with enhanced uniformity in terms of microstructures and properties. Both aluminum and aluminum-carbon nanotube composites have been successfully processed using this new approach.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Properties of Rolled AZ31 Magnesium Alloy Sheet Fabricated by Continuous Variable Cross-Section Direct Extrusion

Rolling is currently a widely used method for manufacturing and processing high-performance magnesium alloy sheets and has received widespread attention in recent years. Here, we combined continuous variable cross-section direct extrusion (CVCDE) and rolling processes. The microstructure and mechanical properties of the resulting sheets rolled at different temperatures from CVCDE extrudate were investigated by optical microscopy, scanning electron microscope, transmission electron microscopy and electron backscatter diffraction. The results showed that a fine-grained microstructure was present with an average grain size of 3.62 μm in sheets rolled from CVCDE extrudate at 623 K. Dynamic recrystallization and a large strain were induced by the multi-pass rolling, which resulted in grain refinement. In the 573-673 K range, the yield strength, tensile strength and elongation initially increased and then declined as the CVCDE temperature increased. The above results provide an important scientific basis of processing, manufacturing and the active control on microstructure and property for high-performance magnesium alloy sheet.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The Prediction of Microstructure Evolution of 6005A Aluminum Alloy in a P-ECAP Extrusion Study

Finite element modeling (FEM) was applied for predicting the recrystallized structure in extruded 6005 aluminum alloy, and simulated results were experimentally validated. First, microstructure evolution of 6005 aluminum alloy during deformation was studied by means of isothermal compression test, where the processing parameters were chosen to reproduce the typical industrial conditions. Second, microstructure evolution was analyzed, and the obtained information was used to fit a dynamic recrystallization model implementing inside the DEFORM-3D FEM code environment. FEM of deformation of 6005 aluminum has been established and validated by microstructure comparison. Finally, the obtained dynamic recrystallization model was applied to tube extrusion by using a portholes-equal channel angular pressing die. The finite element analysis results showed that coarse DRX grains occur in the extruded tube at higher temperature and in the extruded tube at the faster speed of the stem. The test results showed material from the front end of the extruded tube has coarse grains (60 μm) and other extruded tube has finer grains (20 μm).

36 MATERIALS SCIENCE↗
DOE OSTI2018

Tension–Compression Asymmetry Improved by Cold Extrusion in Pure Magnesium

In this paper, cold extrusion was successfully used to fabricate the fine-grained pure Mg bar with average grain size of 2.5 μm. The microstructure, texture and mechanical properties were evaluated by electron backscattering diffraction and mechanical test. The results showed that the corresponding yield strengths for as-extruded fine-grained pure Mg were 130.8 MPa in tension and 125.6 MPa in compression, leading to a greatly improved yield asymmetry ratio. The improvement in tension–compression asymmetry is mainly due to grain refinement which favors the suppression of deformation twinning in compression and promotion of multi-deformation modes both in tension and compression at small strains.

36 MATERIALS SCIENCE↗