ULTRASONIC MEASUREMENTS OF ELASTIC PROPERTIES OF SMALL SPECIMENS AT HIGH PRESSURE CONTRIBUTION NO. 13
Ultrasonic measurements of density and elastic constants at high pressure
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ultrasonic measurements of density and elastic constants at high pressure
Abstract This study focuses on unraveling the microphysical origins of the nonlinear elastic effects, which are pervasive in the Earth's crust. Here, we examine the influence of grain shape on the elastic nonlinearity of granular assemblies. We find that the elastic nonlinearity of angular sand particles is of the same order of magnitude as that previously measured in spherical glass beads. However, while the elastic nonlinearity of glass beads increases by an order of magnitude with RH that of sand particles is rather RH independent. We attribute this difference to the angularity of sand particles: absorbed water on the spherical grains weakens the junctions making them more nonlinear, while no such effect occurs in sand due to grain interlocking. Additionally, for one of the nonlinear parameters that likely arises from shearing/partial slip of the grain junctions, we observe a sharp amplitude threshold in sand which is not observed in glass beads.
The influence of elevated and cryogenic temperatures on the elastic moduli and fracture strengths of several C6000/PMR-15 and C6000/NR-15082 laminates was measured. Tests were conducted at -157 C, 24 C, and 316 C (-250 F, 75 F, and 600 F). Both notched and unnotched laminates were tested. The average stress failure criterion was used to predict the fracture strength of quasi-isotropic notched laminates.
The influence of elevated and cryogenic temperatures on the elastic moduli and fracture strengths of several C6000/PMR-15 and C6000/NR-15082 laminates was measured. Tests were conducted at -157 C, 24 C, and 316 C (-250 F, 75 F, and 600 F). Both notched and unnotched laminates were tested. The average stress failure criterion was used to predict the fracture strength of quasi-isotropic notched laminates.
The effect of long-range order on single-crystal elastic constants of Pd{sub 0.5}Ag{sub 0.5} alloy has been investigated using first-principles electronic structure calculations. The lowest energy among the considered ordered, partially ordered, and disordered structures is found to be the L1{sub 1} layered structure, which is formed by alternate (111) Pd and Ag layers. The ordering effect is found to follow a clear trend: in contrast to the disordered phase, for which the K{sub a} and K{sub c} compressibilities are equal, the L1{sub 1} structure becomes less compressible along the c axis than along the a axis.
In situ neutron diffraction data was collected during elastic loading of rolled foils of uranium-10 wt.% molybdenum bonded to a thin layer of zirconium. Lattice parameters were ascertained from the diffraction patterns to determine the elastic strain and, subsequently, the elastic moduli and Poisson’s ratio in the rolling and transverse directions. The foil was found to be elastically isotropic in the rolling plane with an effective modulus of 86 + / - 3 GPa and a Poisson’s ratio 0.39 + / - 0.04.
Measurements of the sound velocities in a single crystal of FeSi were performed in the temperature range 4-300 K. Elastic constants C{sub 11} and C{sub 44} deviate from a quasiharmonic behavior at high temperature; on the other hand, elastic constants C{sub 12} increases anomalously in the entire temperature range, indicating a change in the electron structure of this material.
By means of first-principles calculations, we have investigated a size dependence of elastic modulus in single-walled ZnO nanotubes with armchair and zigzag forms. It is found that for these tubes the Young's modulus is increased dramatically with the increased diameters and inversely proportional to the Zn-O bond length. Further, the amount of charge transfer, calculated by the Bader analysis, is introduced to elucidate the strength of bonding between Zn and O atoms in these tubes.
First-principles simulations of Ca-based metallic glass-forming alloys yield sample amorphous structures whose structures can be compared to experiment and whose properties can be analyzed. In an effort to understand and control ductility, we investigate the elastic moduli. Calculated Poisson ratios depend strongly on alloying elements in a manner that correlates with ionicity (charge transfer). Consequently, we predict that alloying Ca with Mg and Zn should result in relatively ductile glasses compared to alloying with Ag, Cu, or Al. Experimental observations validate these predictions.
Rayleigh-Ritz and modified Rayleigh-Ritz procedures are used to construct approximate solutions for the response of a thick-walled sphere to uniform pressure loads and an arbitrary radial temperature distribution. The thermoelastic properties of the sphere are assumed to be transversely isotropic and nonhomogeneous; variations in the elastic stiffness and thermal expansion coefficients are taken to be an arbitrary function of the radial coordinate and temperature. Numerical examples are presented which illustrate the effect of the temperature-dependence upon the thermal stress field. A comparison of the approximate solutions with a finite element analysis indicates that Ritz methods offer a simple, efficient, and relatively accurate approach to the problem.
The Brillouin light-scattering technique was used to determine experimentally the three independent elastic constants of cubic aluminum oxynitride at the ambient condition. They are C 11 =334.8(±1.8) GPa , C 12 =164.4(± 1.2) GPa , and C 44 =178.6(± 1.1) GPa . Its bulk modulus is 221.2 GPa. The magnitude of Zener anisotropic ratio is 2.1 similar to other spinels. Here, the anisotropic nature of the material is shown by a large variation in the Young’s modulus and Poisson’s ratio with crystallographic directions. The material was found to be auxetic in certain orientations.
The high pressure equation of state for the W 0.75 R e 0.25 alloy is experimentally determined up to 183 GPa with synchrotron angle-dispersive powder x-ray diffraction in the diamond-anvil cell and to ∼925 GPa with density-functional theory. W-Re alloys are used in many industrial high-temperature applications and as a confining gasket material in high-pressure diamond-anvil cell research. The inclusion of 25 wt. % Re achieves the highest performance in terms of strength and ductility while also maintaining the body-centered-cubic (bcc) crystal structure, yet to date there has been no investigation into its elastic behavior at high pressure. We present the experimentally and theoretically determined volumetric and elastic pressure response and systematically compare these results to other W-Re alloys, finding that the bulk modulus of W-Re alloys varies nonlinearly with Re content and W 0.75 Re 0.25 becomes less incompressible than W at 85 GPa. Published by the American Physical Society 2025
Ultrasonic interferometry was utilized in conjunction with synchrotron-based X-ray diffraction and X-radiographic imaging to determine the compressional and shear wave velocities and unit-cell volumes of pyrite (FeS{sub 2}) at room temperature and pressures up to 9.6 GPa. Fitting all of the experimental volume and velocity data to third-order finite-strain equations yielded the adiabatic zero-pressure bulk and shear moduli and their first pressure derivatives: K{sub S0}=138.9(7) GPa, G{sub 0}=112.3(3) GPa, ({partial_derivative} K{sub S0}/{partial_derivative} P){sub T} =K{sub S0'}=6.0(1), ({partial_derivative}G{sub 0}/{partial_derivative}P){sub T} =G{sub 0'}=3.0(<1), where the numbers in parentheses represent the 1{sigma} uncertainty in the last significant digit. These results are in good agreement with several previous static compression studies on this material but differ quite strongly from the results obtained via first principles calculations. This study presents the first direct measurement of the bulk shear properties of this material.
We have performed high pressure-temperature Brillouin scattering measurements on single crystal hydrogen sulfide using externally heated diamond anvil cell techniques. The pressure dependences of the acoustic velocities, isothermal elastic constants, and moduli of single crystal hydrogen sulfide have been determined along four isotherms. Both elastic constants and moduli increase monotonously with pressure along each isotherm, while they show a decreased tendency with temperature elevated under the same pressure points. The experimental equation of state of single crystal hydrogen sulfide is obtained by fitting with a third-order Birch-Murnaghan and Tait equation. It is proposed that the effect of hydrogen bonds contributes to the unique tendency of elastic anisotropy in single crystal hydrogen sulfide. Through our work, we have extended the melting curve and phase diagram of hydrogen sulfide up to 12 GPa and 580 K.
While thermal expansion data exists for quenched (as well as aged) U-6wt%Nb, there is wide variation in the reported room temperature elastic moduli. To better understand the room temperature elastic behavior and to address the complete absence of data on the temperature dependence of the elastic moduli, room temperature and in-situ elevated temperature resonant ultrasonic spectroscopy (RUS) was performed along with x-ray diffraction (XRD) and dilatometry using a thermomechanical analyzer (TMA). An in-situ small- and wide-angle x-ray scattering (SAXS/WAXS) experiment was performed on a companion sample to help interpret the results. The room temperature polycrystalline dynamic moduli were measured to be E = 95.4 ± 4.5 GPa and G = 35.2 ± 0.2 GPa, respectively. As the temperature is raised, the stiffness slowly decreases, consistent with the empirical rule proposed by Varshni, up to the point of precipitation of the equilibrium α-U phase, which is stiffer than the martensitic phases. Homogenization theory of composites can be used to rationalize the observed response at high temperatures and after high-temperature exposures. Further, aging of the material at low temperatures (≤200°C) does not affect the linear elastic stiffness, but does impact the damping behavior which can be measured through RUS. This change in damping provides another perspective on the microstructure changes induced by low-temperature aging which also result in significant strengthening.
We measured the phonon dispersion at ambient conditions in single-crystal type-I clathrate K8Zn4Sn42, a material with promising thermoelectric properties that has only recently been synthesized, using the high-energy resolution inelastic X-ray scattering (IXS) technique. From the sound velocities along high-symmetry directions, we extracted the elastic constants (C 11, C 12, C 44 = 63.2, 19.1, 21.9 GPa, respectively). Experimental results agree with the predictions from first-principles calculations on the hypothetical, "guest-free", type-I clathrate Sn46. The size of the crystal investigated was several orders of magnitude smaller than what is required for neutron and ultrasonic measurements. Due to this essential property, together with the high-energy resolution, high-momentum-transfer resolution, and the access to the strongest Bragg reflections, IXS is the technique of choice for measuring the full elastic constant tensor for microcrystals.
Here, we measured the elastic velocities of a synthetic polycrystalline β-Mg 2 SiO 4 containing 0.73 wt.% H 2 O to 10 GPa and 600 K using ultrasonic interferometry combined with synchrotron X-radiation. Third-order Eulerian finite strain analysis of the high P and T data set yielded K so = 161.5(2) GPa, G o = 101.6(1) GPa, and (∂K s /∂P) T = 4.84(4), (∂G/∂P) T = 1.68(2) indistinguishable from K so = 161.1(3) GPa, G o = 101.4(1) GPa, and (∂K s /∂P) T = 4.93(4), (∂G/∂P) T = 1.73(2) from the linear fit. The hydration of the wadsleyite by 0.73 wt.% decreases K s and G moduli by 5.3% and 8.6%, respectively, but no measurable effect was noted for (∂K s /∂P) T and (∂G/∂P) T . The temperature derivatives of the K s and G moduli from the finite strain analysis (∂K S /∂T) P = –0.013(2) GPaK –1 , (∂G/∂T) P = –0.015(0.4) GPaK –1 , and the linear fit (∂K S /∂T) P = –0.015(1) GPaK –1 , (∂G/∂T) P = –0.016(1) GPaK –1 are in agreement, and both data sets indicating the |(∂G/∂T) P | to be greater than |(∂K S /∂T) P |. Calculations yield ΔV p(α-β) = 9.88% and ΔV S(α-β) = 8.70% for the hydrous β-Mg 2 SiO 4 and hydrous α-Mg 2 SiO 4 , implying 46–52% olivine volume content in the Earth’s mantle to satisfy the seismic velocity contrast ΔV s = ΔV P = 4.6% at the 410 km depth.
The initial results of a post-irradiation examination study conducted on CVD SiC tubular specimens irradiated under a high radial heat flux are presented herein. The elastic moduli were found to decrease more than that estimated based on previous studies. The significant decreases in modulus are attributed to the cracks present in the specimens. The stresses in the specimens, calculated through finite element analyses, were found to be greater than the expected strength of irradiated specimens, indicating that the irradiation-induced stresses caused these cracks. In conclusion, the optical microscopy images and predicted stress distributions indicate that the cracks initiated at the inner surface and propagated outward.