Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dilute solution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Flow-induced gelation of living (micellar) polymers

The effect of shear velocity gradients on the size (L) of rodlike micelles in dilute and semidilute solution is considered. A kinetic equation is introduced for the time-dependent concentration of aggregates of length L, consisting of 'bimolecular' combination processes L + L-prime yield (L + L-prime) and unimolecular fragmentations L yield L + (L - L-prime). The former are described by a generalization (from spheres to rods) of the Smoluchowski mechanism for shear-induced coalesence of emulsions, and the latter by incorporating the tension-deformation effects due to flow. Steady-state solutions to the kinetic equation are obtained, with the corresponding mean micellar size evaluated as a function of the Peclet number P (i.e., the dimensionless ratio of the flow rate and the rotational diffusion coefficient). For sufficiently dilute solutions, only a weak dependence of the micellar size on P is found. In the semidilute regime, however, an apparent divergence in the micellar size at P of about 1 suggests a flow-induced first-order gelation phenomenon.

Bruinsma, Robijn↗
DOE OSTI2025

Colloidal Behavior of Plutonium Oxide in Concentrated Electrolyte Solutions

The Hanford Site in Washington State manages legacy high-level radioactive waste streams that display major chemistry and engineering challenges, including the high salt levels and pH values that correspond to conditions under which many classical concepts describing chemical reactivity cannot be applied. One particular challenge that needs to be tackled at Hanford is that Pu concentrations, [Pu], in the soluble phases of the tank wastes are higher than expected based on the solubility of crystalline PuO2, which is widely accepted to be caused by the formation of PuO2 colloid, consisting of nano- to submicron-sized particles (PuO2 NPs). Fundamental research underpinning the behavior of PuO2 NPs under conditions not only relevant to the Hanford tank waste but at high ionic strength in general is needed to reliably predict the chemical reactivity of PuO2 NPs and develop engineering solutions to safely and efficiently process high-level radioactive waste into forms suitable for long-term storage. In this work, we study the behavior of PuO2 NPs (particle size ~100 nm) under high ionic strength conditions by reacting it with highly concentrated (up to 5 M) salt solutions. We explore different electrolyte compositions to elucidate the impact of different anions (NO3-, Cl-, ClO4-, SO42-, C2O42-, CO32-) on the stability of PuO2 NP in the acidic and alkaline pH regime. PuO2 NP aggregation and precipitation as function electrolyte concentration is tracked by a combination of liquid scintillation counting, dynamic light scattering for determination of particle size distributions, and zeta potentials as a proxy for particle charge. At acidic pH, electrolytes containing non-coordinating anions, such as NaNO3, NaCl, and NaClO4 mostly stabilize PuO2 NPs over a large electrolyte concentration range, showing only subtle differences in their reactivity. Other electrolyte anions show a more pronounced effect on the PuO2 NP stability: SO42-, binds directly to the particles’ surface, reverses the particle charge, and precipitates the PuO2 NPs efficiently even at intermediate sulfate concentrations (>0.1 M). In contrast, C2O42- is found to lead to high [Pu] in solution, in the milli-molar range, even at mildly acidic pH (~4). Thermodynamic modeling of the dissolved Pu concentrations using PHREEQC is unable to predict the observed [Pu] in the acidic pH regime, supporting the influence of colloids in maintaining elevated [Pu]. It is noteworthy that the current thermodynamic databases do not include constants for colloidal Pu phases and cannot accurately predict many of the high ionic strength solutions relevant to this work. The mechanisms and models responsible for these observations will need further investigation in the future. At high pH values (~12), PuO2 NPs exhibits classical sol-gel chemistry, meaning that upon destabilization of the colloidal sol, for example by addition of concentrated NaOH, highly porous and viscid PuO2 coagulates are formed that consist of a three-dimensional network likely held together by physical interactions. The PuO2 NP coagulate shows no significant reversibility of the aggregation when contacted with concentrated brines; however, PuO2 NPs can be efficiently resuspended in solution by addition of diluted electrolytes, alkaline solutions containing high amounts of carbonate, or simple addition of water. Especially carbonate is shown to stabilize PuO2 NPs in solution at high pH, characterized by stable colloidal suspensions that are resistant against sedimentation during centrifugation. Thermodynamic modeling of the carbonate system was able to predict an increasing dissolved Pu concentration with increasing carbonate concentration. However, the model was profoundly sensitive to the fixed redox potential and does not include any thermodynamic constants for colloidal Pu species.

Neumann, Julia↗
NASA NTRS1995

Prototype development and test results of a continuous ambient air monitoring system for hydrazine at the 10 ppb level

A Hydrazine Vapor Area Monitor (HVAM) system is currently being field tested as a detector for the presence of hydrazine in ambient air. The MDA/Polymetron Hydrazine Analyzer has been incorporated within the HVAM system as the core detector. This analyzer is a three-electrode liquid analyzer typically used in boiler feed water applications. The HVAM system incorporates a dual-phase sample collection/transport method which simultaneously pulls ambient air samples containing hydrazine and a very dilute sulfuric acid solution (0.0001 M) down a length of 1/4 inch outside diameter (OD) tubing from a remote site to the analyzer. The hydrazine-laden dilute acid stream is separated from the air and the pH is adjusted by addition of a dilute caustic solution to a pH greater than 10.2 prior to analysis. Both the dilute acid and caustic used by the HVAM are continuously generated during system operation on an "as needed" basis by mixing a metered amount of concentrated acid/base with dilution water. All of the waste water generated by the analyzer is purified for reuse by Barnstead ion-exchange cartridges so that the entire system minimizes the generation of waste materials. The pumping of all liquid streams and mixing of the caustic solution and dilution water with the incoming sample are done by a single pump motor fitted with the appropriate mix of peristaltic pump heads. The signal to noise (S/N) ratio of the analyzer has been enhanced by adding a stirrer in the MDA liquid cell to provide mixing normally generated by the high liquid flow rate designed by the manufacturer. An onboard microprocessor continuously monitors liquid levels, sample vacuum, and liquid leak sensors, as well as handles communications and other system functions (such as shut down should system malfunctions or errors occur). The overall system response of the HVAM can be automatically checked at regular intervals by measuring the analyzer response to a metered amount of calibration standard injected into the dilute acid stream. The HVAM system provides two measurement ranges (threshold limit value (TLV): 10 to 1000 parts per billion (ppb)/LEAK: 100 ppb to 10 parts per million (ppm)). The LEAK range is created by dilution of the sulfuric acid/hydrazine liquid sample with pure water. This dual range capability permits the analyzer to quantify ambient air samples whose hydrazine concentrations range from 10 ppb to as high as 10 ppm. The laboratory and field prototypes have demonstrated total system response times on the order of 10 to 12 minutes for samples ranging from 10 to 900 ppb in the lLV mode and is greater than 2 minutes for samples ranging from 100 to 1300 ppb in the LEAK mode. Service intervals of over 3 months have been demonstrated for continuous 24 hour/day, 7 day/week usage. The HVAM is made up of a purged cabinet that contains power supplies, RS422 signal transmission capabilities, a UPS, an on-site warning system, and a Line Replaceable Unit (LRU). The LRU includes all of the liquid flow system, the analyzer, the control/data system microprocessor and assorted flow and liquid-level sensors. The LRU is mounted on a track slide system so it can be serviced inplace or totally removed and quickly exchanged with another calibrated unit, thus minimizing analyzer downtime. Once an LRU is removed from an analyzer enclosure, it can be brought to a laboratory facility for complete calibration and periodic maintenance.

Meneghelli, Barry↗
DOE OSTI2022

Determination of Infinite Dilution Activity Coefficients of Molecular Solutes in Ionic Liquids and Deep Eutectic Solvents by Factorization-Machine-Based Neural Networks

Widely known as “green solvents,” ionic liquids (ILs) and deep eutectic solvents (DESs) have been used as substitutes for traditional organic solvents in separation science. To achieve better separations using ILs and DESs, this work aimed to predict the infinite dilution activity coefficients (IDACs) of molecular solutes in these solvents with the state-of-the-art factorization-machine-based neural network (DeepFM). DeepFM combines the benefits of factorization machines and deep neural networks to learn both low-order and high-order interactions among features. The IDAC prediction model was established with 52,372 experimental IDAC datapoints including 260 solvents (252 ILs and 8 DESs) and 112 molecular solutes collected at various temperatures from 288.15 to 428.15 K. Chemical information describing the ILs, DESs, and molecular solutes was included in the IDAC prediction model, including chemical functional groups, molecular weights, and Abraham solvation parameters. The IDAC prediction model showed an improved accuracy compared with alternative models; additionally, DESs were included in the IDAC prediction model for the first time. Here, the model will reduce the energy and resources needed to optimize the selection of ILs and DESs for specific separations, which will promote the development of these green solvents for sustainable chemical processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Wet chemical techniques for passivation of YBa2Cu3O7(7-x)

Wet chemical techniques are described for treatment of YBa2Cu3O(7-x) surfaces, resulting in the formation of native compounds with little or no reactivity to water. Promising native compounds include CuI, BaSO4, CuS, Cu2S, and the oxalates, all of which are either insoluble or have very low solubility in water. Treatment with dilute HI results in the formation of a native iodide film which is 80-90 percent CuI with small amounts of YI3 and BaI2. Treatment with dilute H2SO4 results in the formation of a film which is 95 percent BaSO4 and 5 percent Y2(SO4)3. Cu2S is formed on the surface with a dilute Na2S solution. An oxalate film with equal amounts of Y2(C2O4)3 and BaC2O4 results from treatment with dilute oxalic acid. X-ray photoelectron spectra show no significant changes when the sulfide, sulfate, or oxalate films are dipped in water, while the iodide film shows evidence of Cu(OH)2 formation.

Vasquez, R. P.↗
DOE OSTI2024

Acid–base concentration swing for direct air capture of carbon dioxide

This work demonstrates the first experimental evidence of the acid–base concentration swing (ABCS) for direct air capture of CO 2 . This process is based on the effect that concentrating particular acid–base chemical reactants will strongly acidify solution, through Le Chatelier's principle, and result in outgassing absorbed CO 2 . After collecting the outgassed CO 2 , diluting the solution will result in a reversal of the acid–base reaction, basifying the solution and allowing for atmospheric CO 2 absorption. The experimental study examines a system that includes sodium cation as the alkalinity carrier, boric acid, and a polyol complexing agent that reversibly reacts with boric acid to strongly acidify solution upon concentration. Though the tested experimental system faces absorption rate and water capacity limitations, the ABCS process described here provides a basis for further process optimization. A generalized theoretical ABCS reaction framework is developed and different reaction orders and conditions are studied mathematically. Higher order reactions yield favorable cycle output results, reaching volumetric cycle capacity above 50 mM for third-order and 80 mM for fourth-order reactions. Optimal equilibrium constants are determined in order to guide alternative chemical searches and synthetic chemistry design targets. There is a substantial energetic benefit for reaction orders above the first, with second- and third-order ABCS cycles exhibiting a thermodynamic minimum work for the concentrating and outgassing steps around 150 kJ per mole of CO 2 . A significant advantage of the ABCS is that it can be driven through well-developed and widely-deployed desalination technologies, such as reverse osmosis, with opportunities for energy recovery when recombining the concentrated and diluted streams, and extraction can occur directly from the liquid phase upon vacuum application.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Stability of plutonium oxide nanoparticles in the presence of montmorillonite and implications for colloid facilitated transport

The physical and chemical stability of PuO 2 nanoparticles (intrinsic colloids) in groundwater will control their transport and may affect the performance of high-level radioactive waste repositories. In this study, we examined the chemical stability of two types of PuO 2 nanoparticles at both 25 and 80 °C. The “alkaline” PuO 2 nanoparticles were prepared by neutralizing an acidic Pu(IV) solution with dilute NaOH to pH ~9.5. The “acidic” PuO 2 nanoparticles were precipitated from 0.1 M nitric acid by heating a Pu(IV) solution at 60–80 °C for 30 min. The chemical stability of these PuO 2 nanoparticles was tested in the presence of montmorillonite, a common mineral in the environment and potentially relevant backfill material in some nuclear waste repository designs. The “alkaline” PuO 2 nanoparticles were found to be unstable over a timescale of months at both 25 and 80 °C, with elevated temperature enhancing their dissolution rates and sorption to montmorillonite. PuO 2 nanoparticle dissolution rates decreased with increasing Pu concentration, consistent with solution saturation. The “acidic” PuO 2 nanoparticles appeared to remain stable for much longer than the “alkaline” PuO2 nanoparticles. The “alkaline” PuO 2 nanoparticle dissolution rate constants were as high as 10 -11.9±0.4 mol m -2 s -1 and 10 -11.2±0.2 mol m -2 s -1 at 25 and 80 °C, respectively, while the “acidic” PuO 2 nanoparticle dissolution rate at 80 °C was 10 -13.5 mol m -2 s -1 . Based on transmission electron microscopy, the “alkaline” and “acidic” PuO 2 nanoparticles were of similar size (2.5–4.5 and 2–3 nm nanoparticles, respectively). However, the “acidic” PuO 2 nanoparticles formed more ordered nanoparticle aggregates. Our results suggest that the specific conditions experienced during PuO 2 nanoparticle formation could significantly affect the stability of PuO 2 in the presence of competing sorption processes and, in turn, the relative importance of intrinsic versus pseudocolloid transport in the environment.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

In Situ Imaging of Faujasite Surface Growth Reveals Unique Pathways of Zeolite Crystallization

Zeolite crystallization occurs by complex processes involving a variety of possible mechanisms. The sol gel media used to prepare zeolites leads to heterogeneous mixtures of solution and solid states with diverse solute species. At later stages of zeolite synthesis when growth occurs predominantly from solution, classical two-dimensional nucleation and spreading of layers on crystal surfaces via the addition of soluble species is the dominant pathway. At earlier stages, these processes occur in parallel with nonclassical pathways involving crystallization by particle attachment (CPA). The relative roles of solution- and solid-state species in zeolite crystallization have been a subject of debate. Here, in this work, we investigate the growth mechanism of a commercially relevant zeolite, faujasite (FAU). In situ atomic force microscopy (AFM) measurements reveal that supernatant solutions extracted from a conventional FAU synthesis at various times do not result in growth, indicating that FAU growth predominantly occurs from the solid state through a disorder-to-order transition of amorphous precursors. Elemental analysis shows that supernatant solutions are significantly more siliceous than both the original growth mixture and the FAU zeolite product; however, in situ AFM studies using a dilute clear solution with a lower Si/Al ratio revealed three-dimensional growth of surfaces that is distinct from layer-by-layer and CPA pathways. This unique mechanism of growth differs from those observed in studies of other zeolites. Given that relatively few zeolite frameworks have been the subject of mechanistic investigation by in situ techniques, these observations of FAU crystallization raise the question whether its growth pathway is characteristic of other zeolite structures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Chemostatic concentration–discharge behaviour observed in a headwater catchment underlain with discontinuous permafrost

Concentration–discharge dynamics were evaluated in a small (~ 2.25 km2) headwater catchment underlain with discontinuous permafrost on the Seward Peninsula of western Alaska. A large storm, during which 48 mm of rain fell over a 24-h period, enabled the evaluation of solute concentration–discharge response to a sizeable hydrological event, while water stable isotopes enabled an appraisal of the contributions of event water. Under normal catchment conditions, chemostatic behaviour was observed for solutes typically derived from mineral weathering (e.g. calcium, magnesium, sodium and silica). The chemostatic behaviour observed for most solutes under normal catchment conditions indicated that catchment storage and residence times are sufficiently long for many solute generating reactions to approach equilibrium. Following the storm however, most solutes exhibited dilutive and highly variable behaviour. This likely indicated the exceedance of a discharge threshold where chemostatic behaviour could no longer be maintained for most solutes. Dissolved organic carbon and silica were the only solutes monitored to exhibit chemostatic behaviour during all time periods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Membrane-based solvent extraction for the recovery of rare earths from phosphate mining process streams

This study reports on the capture of rare earth elements (REEs) from phosphate industry process streams, including phosphoric acid (PA) sludge and phosphogypsum (PG), using a membrane solvent extraction (MSX) process. While MSX has been proven effective for a relatively concentrated feed, its effectiveness for dilute REEs solutions remains unexplored. Investigated PA-sludge and PG particles contain total REEs concentrations of ∼1100 and ∼320 ppm, respectively. Acid leaching, implemented to dissolve the REEs, significantly dilutes the REEs concentration to ∼210 ppm for PA-sludge leachate and ∼60 ppm for PG leachate. These low concentrations, compounded by the higher levels of non-REE ions and radioactive species, uranium (U) and thorium (Th), poses challenges to the MSX process. Here, we demonstrated that N,N,N′,N′-tetraoctyl-diglycolamide (TODGA) selectively binds REEs from a >3 M nitric-acid leachate while effectively rejecting U and Th. Concentrations of light REEs in strip solution were doubled compared to the feed, while heavy REEs were preferentially extracted. Furthermore, >99% purity gypsum, free of U and Th, was precipitated during the acid leaching process, aiding separation by removing significant amounts of non-REEs species (e.g., calcium) prior to the MSX process. Molecular simulations support the experimental data, suggesting preferential separation of heavy over light REEs. Based on these results, a cost-effective integrated process including pretreatment, acid leaching, MSX, and wastewater treatment is proposed for the co-recovery of REEs, phosphoric acid, gypsum, and U. This study shows MSX as a technically and economically feasible process for the recovery of REEs from low-concentration process streams, offering advantages over conventional solvent extraction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The effect of lignin degradation products on the generation of pseudo-lignin during dilute acid pretreatment

Pseudo-lignin is an insoluble material that tends to deposit on acidic pretreated fiber surface and negatively impacts the biological conversion of biomass to valued added products. Employing a laboratory generated acidic hydrolysate solution from dilute acid pretreatment of bamboo residues, we sought to seek an improved understanding of pseudo-lignin formation from fragmented carbohydrates. In addition, we also performed experiments to investigate how lignin model compounds interact with carbohydrates en route to pseudo-lignin’s formation. The yields of pseudo-lignin generated from xylose (CXPL) were higher than those generated from glucose (CGPL). Gas chromatography-Mass spectrometry and Foloin-Ciocalteau analysis suggested that there were more aromatic compounds in hydrolyzate during CGPL’s formation. The presence of lignin phenolic model compounds had both a positive and negative effect upon quantitative yields of pseudo-lignin. Gel permeation chromatography and NMR analysis ( 31 P and 2D-HSQC NMR) of the pseudo-lignin samples generated in the presence and absence of 4-hydroxybenzoic acid (4-HA), employed as a lignin model compound, revealed drastic differences in molecular weight, changes in hydroxyl group content, and hydrocarbon bonds, suggesting significant differences in the pseudo-lignin reaction pathways when certain lignin model compounds are present. Finally, our findings demonstrate the effects of both hemicellulose carbohydrate makeup and lignin model compound impact on the formation of pseudo-lignin and its chemical properties, suggesting a potential way to minimize pseudo-lignin formation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

SANS quantification of bound water in water-soluble polymers across multiple concentration regimes

Contrast-variation small-angle neutron scattering (CV-SANS) is a widely used technique for quantifying hydration water in soft matter systems, but it is predominantly applied in the dilute regime or for systems with a well-defined structure factor. Here, CV-SANS was used to quantify the number of hydration water molecules associating with three water-soluble polymers with different critical solution temperatures and types of water–solute interactions in dilute, semidilute, and concentrated solution through the exploration of novel methods of data fitting and analysis. Multiple SANS fitting workflows with varying levels of model assumptions were evaluated and compared to give insight into SANS model selection. These fitting pathways ranged from general, model-free algorithms to more standard form and structure factor fitting. In addition, Monte Carlo bootstrapping was evaluated as a method to estimate parameter uncertainty through simulation of technical replicates. The most robust fitting workflow for dilute solutions was found to be form factor fitting without CV-SANS ( i.e. polymer in 100% D 2 O). For semidilute and concentrated solutions, while the model-free approach can be mathematically defined for CV-SANS data, the addition of a structure factor imposes physical constraints on the optimization problem, suggesting that the optimal fitting pathway should include appropriate form and structure factor models. The measured hydration numbers were consistent with the number of tightly bound water molecules associated with each monomer unit, and the concentration dependence of the hydration number was largely governed by the chemistry-specific interactions between water and polymer. Polymers with weaker water–polymer interactions ( i.e. those with fewer hydration water molecules) were found to have more bound water at higher concentrations than those with stronger water–polymer interactions due to the increase in the number of forced water–polymer contacts in the concentrated system. This SANS-based method to count hydration water molecules can be applied to polymers in any concentration regime, which will lead to improved understanding of water–polymer interactions and their impact on materials design.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Linear Viscoelastic Properties of Putative Cyclic Polymers Synthesized by Reversible Radical Recombination Polymerization (R3P)

Linear viscoelastic properties in both melt and solution states are reported for a series of poly(3,6-dioxa-1,8-octanedithiol) (polyDODT) made by reversible radical recombination polymerization (R 3 P) under conditions designed to produce linear (LDODT), cyclic (RDODT) and linear-cyclic mixtures (LRDODT). PolyDODT is amorphous (T g < -50 °C) and highly flexible (entanglement molecular weight M e,lin ≈ 1850 g/mol for LDODT). PolyDODT’s low T g and low M e,lin enable characterization over a wide dynamic range and a wide range of dimensionless weight-average molecular weight Z w = M w /M e,lin . Measurements at temperatures from -57 °C to 100 °C provide up to 18 deades of reduced frequency, which is necessary to characterize RDODT melts with Z w from 23 to 300. The two highest molecular weight polymers in the present RDODT series have such high M w (406k and 556k g/mol) that mass spectrometry, NMR spectroscopy, and even chemical assays for chain ends are unable to rule out up to 2 mol% linear contaminant. By studying the samples in solution (using dilution to reduce Z w ) we could compare their dynamics with those of previously established high-purity polystyrene (PS) rings (limited to Z w ≤ 13.6). RDODT solutions with Z w < 15 (concentrations <5wt% for RDODT-406k and 556k) have dynamic moduli G^* that accord with LCCC-purified PS rings in terms of the frequency dependence (including the absence of a plateau), the progression of shapes of G* as a function of Z w , and the linear scaling of their zero-shear viscosity η0 with M w . The shape of G* as a function of Z w for solutions of RDODT-406k and -556k also accord with lower M w RDODT melts (which have ≤ 1.3mol% linear contaminant). Thus, measurement of the linear viscoelastic properties of appropriate concentrations of high M w (>200k g/mol) putative cyclic polymers, in which linear chains evade spectroscopic detection, may provide an alternative means (though not fully proven) of validation of sample purity. When Z w > 15 (including all seven RDODT melts and eight of their solutions), G* has a rubbery plateau. This suggests that the onset of entanglement-like behavior in rings requires 4-5-fold greater Z w than is required for linear chains. Further, the plateau moduli of RDODT samples are indistinguishable from G N o of the corresponding LDODT (melt or matched-concentration solutions). In entangled linear polymers, the observation that G N o is independent of Z w follows from limitations on lateral fluctuations due to neighboring chains becoming independent of position along a given chain. The present results for RDODT suggest that this holds for sufficiently long endless chains, too. While the RDODT have the same G N o as entangled LDODT, when Z w > 60 the terminal relaxation, if reached at all, of RDODT extends to orders of magnitude lower frequency than an entangled linear polymer of the same Z w . Consequently, the viscosity of RDODT with Z w > 60 increases with Z w much more strongly than the 3.4-power observed for entangled linear polymers. Lastly, these novel polymers, with disulfide-linked backbone and broad relaxation time distribution may prove important in relation to biodegradable elastomers and materials with exceptional low-frequency dissipation, extending at least 12 decades below the onset of the rubbery plateau.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Unexpected Conformational Behavior of Poly(poly(ethylene glycol) methacrylate)-Poly(propylene carbonate)-Poly(poly(ethylene glycol) methacrylate) (PPEGMA-PPC-PPEGMA) Amphiphilic Block Copolymers in Micellar Solution and at the Air-Water Interface

Self-assemblies (bulk micelles and Langmuir monolayers) of a new amphiphilic block copolymer, poly(poly(ethylene glycol) methacrylate)-poly(propylene carbonate)-poly(poly(ethylene glycol) methacrylate) (PPEGMA-PPC-PPEGMA), were investigated in dilute aqueous solution and at the air-water interface. An important feature that distinguishes PPEGMA-PPC-PPEGMA from conventional linear PEG-based polymer surfactants is that in the hydrophilic PPEGMA block the PEG moieties exist as side chains attached to the poly(methacrylate) (PMA) backbone. This study was performed using three PPEGMA-PPC-PPEGMA samples having an identical PPC molecular weight (5.6 kDa) and different PPEGMA molecular weights (7.3, 2.8 and 2.1 kDa on either side) (named as “G7C6G7”, “G3C5G3”, and “G2C6G2”, respectively). Cryo-TEM images revealed that G2C6G2 micelles form large clusters, whereas G7C6G7 micelles exist as unimers; the behavior of G3C6G3 is intermediate. The average core surface distance between two adjacent G2C6G2 micelles in a cluster was estimated to be only about 3.7 nm, which suggests that in the micelle corona layer only the PEG side chains (but not the PMA backbone) exist as hydrated brush chains. A calculation showed that at the small micelle separation distance observed, the van der Waals attractive forces become significant, and are thus likely responsible for the cluster formation. Steady shear rheometry measurements confirmed that G2C6G2 micelles are indeed only weakly bound in clusters, and these micelle clusters are thus prone to breakup even under mild steady shear. The micelle breakup force estimated from the shear viscosity data is in reasonable agreement with an estimate obtained from the theoretical van der Waals interaction potential. Langmuir monolayers formed at the air-water interface by PPEGMA-PPC-PPEGMA were also characterized; surface pressure-area measurements were performed. Detailed features of the surface pressure-area isotherms further supported that only the PEG side chains are hydrated in the subphase, while the PMA backbone remains unhydrated and situated on the water surface.

Lee, Jaewon↗
NASA NTRS2023

Efficient Two-Way Coupled Analysis of Steady-State Particle-Laden Hypersonic Flows

A direct solution approach for surface erosion in particle-laden hypersonic flows is extended for use in low-cost two-way coupled solutions of dilute gas-particle flows. The Trajectory Control Volume method, which uses a sparse set of probe particles to predict surface erosion distributions on general vehicles, is reformulated for the solution of source terms by mean trajectory subdivision and computing a flux differencing. The approach is verified successfully against a boundary layer solution and shown to agree well with experimental measurements. A representative Mars entry case, with conditions and geometry based on the ExoMars Schiaparelli capsule, is solved with the approach to study the impact of two-way coupling on surface heating and erosion. Results indicate that for realistic loading conditions, heating is largely unmodified compared to one-way coupled results at peak heating trajectory conditions, and no measureable difference is observed in the surface erosion rate. At exaggerated loading conditions high enough to observe coupling effects, the worst case collisional heating can increase heating by up to 60%.

Particle Laden Flow↗
DOE OSTI2025

FY24 Task 4: Studies of Phosphate and Fluoride Solubility for Dissolution of High Phosphate Tank Waste

Knowledge gaps have been identified in phosphate solubility in almost every single- and multi-component system, and particularly for aluminate in phosphate/hydroxide, where uncertainties in predicted values of aluminum solubility are greater than 50%. Solubility data of multicomponent, aqueous electrolytes containing sodium hydroxide, sodium fluoride, sodium phosphate, sodium nitrite, sodium nitrate, and dissolved gibbsite are also sparse. For example, for solutions of (i) sodium nitrate and sodium phosphate, data are only available at 30 and 50 °C, and for (ii) dissolved gibbsite in sodium hydroxide and sodium phosphate, only two data points are available at 20 and 40 °C. There is no data available on mixtures of sodium hydroxide, sodium phosphate, sodium fluoride, and dissolved gibbsite. These knowledge gaps were identified in a technical review of waste solubility data and the impact of dilution on solution stabilities and will be addressed in this work to predict aluminum hydroxide and sodium phosphate solubility in multicomponent electrolytes upon dilution, and upon variation of temperature. Results will provide the technical basis to develop accurate models for (i) gibbsite solubility and mass transfer of aluminum between solid and liquid forms following the sluicing of sludge and saltcake with water; and (ii) further blending of these suspensions with bismuth from bismuth phosphate waste, and zirconium and uranium left from the fuel decladding. This work will be essential to developing a disposition path for retrieval solutions from bismuth phosphate wastes. This effort would also support sludge washing to further reduce phosphate concentration if that process were to be added back to the flowsheet in the future.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1998

Mineral catalysis of a potentially prebiotic aldol condensation

Minerals may have played a significant role in chemical evolution. In the course of investigating the chemistry of phosphonoacetaldehyde (PAL), an analogue of glycolaldehyde phosphate, we have observed a striking case of catalysis by the layered hydroxide mineral hydrotalcite ([Mg2Al(OH)6][Cl.nH2O]). In neutral or moderately basic aqueous solutions, PAL is unreactive even at a concentration of 0.1 M. In the presence of a large excess of NaOH (2 M), the compound undergoes aldol condensation to produce a dimer containing a C3-C4 double-bond. In dilute neutral solutions and in the presence of the mineral, however, condensation takes place rapidly, to produce a dimer which is almost exclusively the C2-C3 unsaturated product.

Non-NASA Center↗