Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Design pattern”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Using Diffusion Bonding in Making Piezoelectric Actuators

A technique for the fabrication of piezoelectric actuators that generate acceptably large forces and deflections at relatively low applied voltages involves the stacking and diffusion bonding of multiple thin piezoelectric layers coated with film electrodes. The present technique stands in contrast to an older technique in which the layers are bonded chemically, by use of urethane or epoxy agents. The older chemical-bonding technique entails several disadvantages, including the following: It is difficult to apply the bonding agents to the piezoelectric layers. It is difficult to position the layers accurately and without making mistakes. There is a problem of disposal of hazardous urethane and epoxy wastes. The urethane and epoxy agents are nonpiezoelectric materials. As such, they contribute to the thickness of a piezoelectric laminate without contributing to its performance; conversely, for a given total thickness, the performance of the laminate is below that of a unitary piezoelectric plate of the same thickness. The figure depicts some aspects of the fabrication of a laminated piezoelectric actuator by the present diffusion- bonding technique. First, stock sheets of the piezoelectric material are inspected and tested. Next, the hole pattern shown in the figure is punched into the sheets. Alternatively, if the piezoelectric material is not a polymer, then the holes are punched in thermoplastic films. Then both faces of each punched piezoelectric sheet or thermoplastic film are coated with a silver-ink electrode material by use of a silkscreen printer. The electrode and hole patterns are designed for minimal complexity and minimal waste of material. After a final electrical test, all the coated piezoelectric layers (or piezoelectric layers and coated thermoplastic films) are stacked in an alignment jig, which, in turn, is placed in a curved press for the diffusion-bonding process. In this process, the stack is pressed and heated at a specified curing temperature and pressure for a specified curing time. The pressure, temperature, and time depend on the piezoelectric material selected. At the end of the diffusion-bonding process, the resulting laminated piezoelectric actuator is tested to verify the adequacy of the mechanical output as a function of an applied DC voltage.

Sager, Frank E.↗
DOE OSTI2023

A simple, validated approach for design of two-dimensional periodic particle patterns via acoustophoresis

Two-dimensional patterning of microparticles enables a wide range of functional materials, including patterned energy storage electrodes, flexible electronics, and sensor arrays. Particle patterning via acoustics offers an attractive path to generate a wide variety of 2D periodic patterns that introduce tailorable hierarchical porosity, useful for controlling surface area, transport distances, and other properties. This method is most effective with micron scale particles and patterns of tens to hundreds of microns. To enable systematic exploration of the broad design space for such patterns, this work develops a model of 2D and 3D assembly of particles at high loadings and validates the obtained patterns against both experiments and more computationally intensive modeling techniques. Using this simple model, connections are mapped between input parameters (like actuation conditions, particle volume fraction, material properties) and output geometrical features (like void size and shape, pattern connectivity, and surface area) so that they can be tailored to given applications. The utility of this simple model is illustrated by predicting and then experimentally demonstrating new hierarchical patterns resulting from multiple waves of different frequencies interacting. These multiscale patterns offer the potential to lift the limits on surface area, diffusion distances, and other features.

42 ENGINEERING↗
NASA NTRS1981

Radio frequency performance predictions for the hoop/column point design

Preliminary antenna pattern tests were conducted to determine if catastrophic effects were produced by cables (conducting) in the aperture. This test consisted of an apex feed illuminating a 3 meter solid reflector. A hoop/column configuration was used in positioning the various wires and cables. Radiation patterns were measured at 7 GHz and 10 GHz. No catastrophic effects were observed for this configuration, but additional tests are required to determine the effects for more precision multiple beam applications. In order to better understand the scattering and blockage effects on multiple beam performance, a 35 GHz model was used to model somewhat a single quad aperture configuration. Experimental results using this models are presented in graphs.

Campbell, T. G.↗
NASA NTRS1986

SSME Seal Test Program: Test results for sawtooth pattern damper seal

Direct and transverse force coefficients for 11, sawtooth-pattern, and damper-seal configurations were examined. The designation damper seal uses a deliberately roughened stator and smooth rotor to increase the net damping force developed by a seal. The designation sawtooth-pattern refers to a stator roughness pattern. The sawtooth pattern yields axial grooves in the stator which are interrupted by spacer elements which act as flow constrictions or dams. All seals use the same smooth rotor and have the same, constant, minimum clearance. The stators examined the consequences of changes in the following design parameters: (1) axial-groove depth; (2) number of teeth: (3) number of sawtooth sections; (4) number of spacer elements; (5) dam width; (6) axially aligned sawtooth sections versus axially-staggered sawtooth sections; and (7) groove geometry. It is found that none of the sawtooth-pattern seal performs as well as the best round-hole-pattern seal. Maximum damping configurations for the sawtooth and round-hole-pattern stators have comparable stiffness performance. Several of the sawtooth pattern stators outperformed the best round-hole pattern seal.

Childs, D. W.↗
NASA NTRS1986

The HXII gas system

Two gas proportional counters were designed: one detector was patterned after the HEAO-1 design which possesses a proven low background capability at atmospheric pressure, and the other was a parallel planar geometry detector with an extensive drift region. The actual performance of the detectors was evaluated with emphasis on background rejection efficiency and position resolution.

Source record↗
NASA NTRS1984

Hoop/column antenna RF verification model. Volume 2: Analysis and correlation

As part of the Large Space System Technology Program, the theoretical and experimental results of the RF characteristic of a hoop/column, quad aperture antenna using an RF verification model are presented. To satisfy the primary purposes of the model, experimental pattern data is provided for the quad aperture configuration at different reflector edge illumination levels, from which the geometry and edge effects can be assessed, and experimental data which can be compared with calculations using various theoretical reflector scattering formulae are provided. It also experimentally determines the effects upon secondary patterns of scale model quartz cables, as used in the hoop/column design, upon secondary patterns in order to assess the importance of developing a scattering theory to predict such effects. In addition, a comprehensive theoretical study and the experimental pattern results of quad aperture antenna feeds, a discussion of the fundamental affect of parasitic side lobes, their amplitude, and location in space.

Croswell, W. F.↗
NASA NTRS1984

Hoop/Column Antenna: RF Verification Model. Volume 1: Test Results

As part of the Large Space System Technology Program, this report, in two volumes, presents the theoretical and experimental results of the RF characteristic of a hoop/column, quad aperture antenna using an RF verification model. To satisfy the primary purposes of the model it provides experimental pattern data for the quad aperture configuration at different reflector edge illumination levels, from which the geometry and edge effects can be assessed, and provides experimental data which can be compared with calculations using various theoretical reflector scattering formulae. It also experimentally determines the effects upon secondary patterns of scale model quartz cables, as used in the hoop/column design, upon secondary patterns in order to assess the importance of developing a scattering theory to predict such effects. In addition, this report contains a comprehensive theoretical study and the experimental pattern results of quad aperture antenna feeds, a discussion of the fundamental affect of parasitic side lobes, their amplitude, and location in space.

Croswell, W. F.↗
NASA NTRS2011

Comparing Methods for Dynamic Airspace Configuration

This paper compares airspace design solutions for dynamically reconfiguring airspace in response to nominal daily traffic volume fluctuation. Airspace designs from seven algorithmic methods and a representation of current day operations in Kansas City Center were simulated with two times today's demand traffic. A three-configuration scenario was used to represent current day operations. Algorithms used projected unimpeded flight tracks to design initial 24-hour plans to switch between three configurations at predetermined reconfiguration times. At each reconfiguration time, algorithms used updated projected flight tracks to update the subsequent planned configurations. Compared to the baseline, most airspace design methods reduced delay and increased reconfiguration complexity, with similar traffic pattern complexity results. Design updates enabled several methods to as much as half the delay from their original designs. Freeform design methods reduced delay and increased reconfiguration complexity the most.

Zelinski, Shannon↗
NASA NTRS2011

Comparing Methods for Dynamic Airspace Configuration

This paper compares airspace design solutions for dynamically reconfiguring airspace in response to nominal daily traffic volume fluctuation. Airspace designs from seven algorithmic methods and a representation of current day operations in Kansas City Center were simulated with two times today's demand traffic. A three-configuration scenario was used to represent current day operations. Algorithms used projected unimpeded flight tracks to design initial 24-hour plans to switch between three configurations at predetermined reconfiguration times. At each reconfiguration time, algorithms used updated projected flight tracks to update the subsequent planned configurations. Compared to the baseline, most airspace design methods reduced delay and increased reconfiguration complexity, with similar traffic pattern complexity results. Design updates enabled several methods to as much as half the delay from their original designs. Freeform design methods reduced delay and increased reconfiguration complexity the most.

Zelinski, Shannon↗
NASA NTRS1994

The design and implementation of EPL: An event pattern language for active databases

The growing demand for intelligent information systems requires closer coupling of rule-based reasoning engines, such as CLIPS, with advanced data base management systems (DBMS). For instance, several commercial DBMS now support the notion of triggers that monitor events and transactions occurring in the database and fire induced actions, which perform a variety of critical functions, including safeguarding the integrity of data, monitoring access, and recording volatile information needed by administrators, analysts, and expert systems to perform assorted tasks; examples of these tasks include security enforcement, market studies, knowledge discovery, and link analysis. At UCLA, we designed and implemented the event pattern language (EPL) which is capable of detecting and acting upon complex patterns of events which are temporally related to each other. For instance, a plant manager should be notified when a certain pattern of overheating repeats itself over time in a chemical process; likewise, proper notification is required when a suspicious sequence of bank transactions is executed within a certain time limit. The EPL prototype is built in CLIPS to operate on top of Sybase, a commercial relational DBMS, where actions can be triggered by events such as simple database updates, insertions, and deletions. The rule-based syntax of EPL allows the sequences of goals in rules to be interpreted as sequences of temporal events; each goal can correspond to either (1) a simple event, or (2) a (possibly negated) event/condition predicate, or (3) a complex event defined as the disjunction and repetition of other events. Various extensions have been added to CLIPS in order to tailor the interface with Sybase and its open client/server architecture.

Giuffrida, G.↗
NASA NTRS1973

Comparative study of patches for liquid cooled garments.

Tests were performed on 12 cooling patches of various designs to establish criteria for the evaluation of their performance in liquid-cooled suits in industrial, military and aerospace applications. The thermal effectiveness value was 0.088 for patch designs with a double spiral flow pattern, and 0.075 for patch designs with a parallel flow pattern. The ratio of thermal energy transfer rate to cooling-medium pumping power requirement is indicated as the prime performance characteristic to be considered in the selection and rating of cooling patches.

Shitzer, A.↗
NASA NTRS1975

Signatures analysis and recognition of severe weather patterns

The feasibility of designing a prediction and warning system for severe weather conditions on the basis of time series analysis and pattern recognition is examined. Data accumulated by Taylor (1972) on the rate of atmospherics produced by severe, tornado-producing storms that struck Oklahoma City during April 1970 are analyzed by time series analysis and pattern recognition. Power spectra, cross-power spectra, coherence functions, and time-varying patterns are analyzed.

Wang, P. P.↗
NASA NTRS1988

Multiple degree of freedom object recognition using optical relational graph decision nets

Multiple-degree-of-freedom object recognition concerns objects with no stable rest position with all scale, rotation, and aspect distortions possible. It is assumed that the objects are in a fairly benign background, so that feature extractors are usable. In-plane distortion invariance is provided by use of a polar-log coordinate transform feature space, and out-of-plane distortion invariance is provided by linear discriminant function design. Relational graph decision nets are considered for multiple-degree-of-freedom pattern recognition. The design of Fisher (1936) linear discriminant functions and synthetic discriminant function for use at the nodes of binary and multidecision nets is discussed. Case studies are detailed for two-class and multiclass problems. Simulation results demonstrate the robustness of the processors to quantization of the filter coefficients and to noise.

Casasent, David P.↗
NASA NTRS1977

A layout designer's data projection reticle

The designer's projection reticle is a modified surplus weapons sighting device consisting of a 3.5 cm diameter, 8.9 focal length coated objective lens. It is placed 1.5 cm in front of a clear flat glass plate on which the aluminized reflective pattern has been deposited. Reflected light passes through the objective lens, off the front surface of the coating, and off the rear coated surface of the objective lens. Several reticle patterns have been designed and tested, and other patterns are in the planning stage. The device may be used for a variety of applications including determining the optimum locations on a cockpit panel for luminous warning indicators requiring rapid manual responses.

Haines, R. F.↗
NASA NTRS1984

Binary Correlator for Electromagnetic Signal Patterns

Modulation patterns recognized with extensive calculations. Set of shift registers contains patterns of 1's and 0's representing presence or absence of received signal in designated time/frequency bins. Pattern in shift registers correlated with pattern of expected signal by shifting each cell to right according to expected pattern and summing shift-register outputs in analog summing network. Useful in applications requiring identification of smaller pattern of 1-bit data within larger matrix of such data.

Garrison, J. B.↗
DOE OSTI2023

Design of Multicomponent Peptide Fibrils with Ordered and Programmable Compositional Patterns

Advanced applications of biomacromolecular assemblies require a stringent degree of control over molecular arrangement, which is a challenge to current synthetic methods. Here we used a neighbor-controlled patterning strategy to build multicomponent peptide fibrils with an unprecedented capacity to manipulate local composition and peptide positions. Eight peptides were designed to have regulable nearest neighbors upon co-assembly, which, by simulation, afforded 412 different patterns within fibrils, with varied compositions and/or peptide positions. The fibrils with six prescribed patterns were experimentally constructed with high accuracy. The controlled patterning also applies to functionalities appended to the peptides, as exemplified by arranging carbohydrate ligands at nanoscale precision for protein recognition. Importantly, this study offers a route to molecular editing of inner structures of peptide assemblies, prefiguring the uniqueness and richness of patterning-based material design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗