Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Composition variations in pulsed-laser-deposited Y-Ba-Cu-O thin films as a function of deposition parameters

The composition of pulsed-ultraviolet-laser-deposited Y-Ba-Cu-O films was examined as a function of position across the substrate, laser fluence, laser spot size, substrate temperature, target conditioning, oxygen pressure and target-substrate distance. Laser fluence, laser spot size, and substrate temperature were found to have little effect on composition within the range investigated. Ablation from a fresh target surface results in films enriched in copper and barium, both of which decrease in concentration until a steady state condition is achieved. Oxygen pressure and target-substrate distance have a significant effect on film composition. In vacuum, copper and barium are slightly concentrated at the center of deposition. With the introduction of an oxygen background pressure, scattering results in copper and barium depletion in the deposition center, an effect which increases with increasing target-substrate distance. A balancing of these two effects results in stoichiometric deposition.

Foote, M. C.↗

CuInS2 Films Deposited by Aerosol-Assisted Chemical Vapor Deposition Using Ternary Single-Source Precursors

Polycrystalline CuInS2 films were deposited by aerosol-assisted chemical vapor deposition using both solid and liquid ternary single-source precursors (SSPs) which were prepared in-house. Films with either (112) or (204/220) preferred orientation, had a chalcopyrite structure, and (112)-oriented films contained more copper than (204/220)-oriented films. The preferred orientation of the film is likely related to the decomposition and reaction kinetics associated with the molecular structure of the precursors at the substrate. Interestingly, the (204/220)-oriented films were always In-rich and were accompanied by a secondary phase. From the results of post-growth annealing, etching experiments, and Raman spectroscopic data, the secondary phase was identified as an In-rich compound. On the contrary, (112)-oriented films were always obtained with a minimal amount of the secondary phase, and had a maximum grain size of about 0.5 micron. Electrical and optical properties of all the films grown were characterized. They all showed p-type conduction with an electrical resistivity between 0.1 and 30 Omega-cm, and an optical band gap of approximately 1.46 eV +/- 0.02, as deposited. The material properties of deposited films revealed this methodology of using SSPs for fabricating chalcopyrite-based solar cells to be highly promising.

Jin, Michael↗

Depositional facies and aqueous-solid geochemistry of travertine-depositing hot springs (Angel Terrace, Mammoth Hot Springs, Yellowstone National Park, U.S.A.)

Petrographic and geochemical analyses of travertine-depositing hot springs at Angel Terrace, Mammoth Hot Springs, Yellowstone National Park, have been used to define five depositional facies along the spring drainage system. Spring waters are expelled in the vent facies at 71 to 73 degrees C and precipitate mounded travertine composed of aragonite needle botryoids. The apron and channel facies (43-72 degrees C) is floored by hollow tubes composed of aragonite needle botryoids that encrust sulfide-oxidizing Aquificales bacteria. The travertine of the pond facies (30-62 degrees C) varies in composition from aragonite needle shrubs formed at higher temperatures to ridged networks of calcite and aragonite at lower temperatures. Calcite "ice sheets", calcified bubbles, and aggregates of aragonite needles ("fuzzy dumbbells") precipitate at the air-water interface and settle to pond floors. The proximal-slope facies (28-54 degrees C), which forms the margins of terracette pools, is composed of arcuate aragonite needle shrubs that create small microterracettes on the steep slope face. Finally, the distal-slope facies (28-30 degrees C) is composed of calcite spherules and calcite "feather" crystals. Despite the presence of abundant microbial mat communities and their observed role in providing substrates for mineralization, the compositions of spring-water and travertine predominantly reflect abiotic physical and chemical processes. Vigorous CO2 degassing causes a +2 unit increase in spring water pH, as well as Rayleigh-type covariations between the concentration of dissolved inorganic carbon and corresponding delta 13C. Travertine delta 13C and delta 18O are nearly equivalent to aragonite and calcite equilibrium values calculated from spring water in the higher-temperature (approximately 50-73 degrees C) depositional facies. Conversely, travertine precipitating in the lower-temperature (< approximately 50 degrees C) depositional facies exhibits delta 13C and delta 18O values that are as much as 4% less than predicted equilibrium values. This isotopic shift may record microbial respiration as well as downstream transport of travertine crystals. Despite the production of H2S and the abundance of sulfide oxidizing microbes, preliminary delta 34S data do not uniquely define the microbial metabolic pathways present in the spring system. This suggests that the high extent of CO2 degassing and large open-system solute reservoir in these thermal systems overwhelm biological controls on travertine crystal chemistry.

Non-NASA Center↗

CuInS2 Films Deposited by Aerosol-Assisted Chemical Vapor Deposition Using Ternary Single-Source Precursors

Polycrystalline CuInS2 films were deposited by aerosol-assisted chemical vapor deposition using both solid and liquid ternary single-source precursors (SSPs) prepared in-house. Films with either (112) or (204/220) preferred orientation were obtained, and compositional analysis showed that (112)-oriented films contained more copper than (204/220)-oriented films. Using X-ray diffraction, the signature of chalcopyrite structure was often confirmed for (112)-oriented films. The preferred orientation of the film is likely related to the decomposition and reaction kinetics associated with the molecular structure of the precursors at the substrate. Interestingly, the (204/220)-oriented films were always accompanied by a secondary phase, which was identified as an unknown In-rich compound from the results of post-growth annealing, etching experiments, and Raman spectroscopic data. By increasing Cu to In ratio in the film, (112)-oriented films were obtained with a maximum grain size of about 0.5 micrometers, and their X-ray diffractions did not show any observable signature of the In secondary phase. Electrical and optical properties of all the films grown were characterized. They all showed p-type conduction with an electrical resistivity between 0.1 omega cm and 30 omega cm, and an optical band gap of 1.46eV +/- 0.02, as deposited. The material properties of deposited films revealed this methodology of using SSPs for fabricating chalcopyrite-based solar cells to be highly promising.

Jin, Michael H.-C.↗

Microstructural and optical properties of nanocrystalline ZnO deposited onto vertically aligned carbon nanotubes by physical vapor deposition

Nanocrystalline ZnO films with thicknesses of 5 nm, 10 nm, 20 nm, and 50 nm were deposited via magnetron sputtering onto the surface of vertically aligned multi-walled carbon nanotubes (MWCNTs). The ZnO/CNTs heterostructures were characterized by scanning electron microscopy, high resolution transmission electron microscopy, and X-ray diffraction studies. No structural degradation of the CNTs was observed and photoluminescence (PL) measurements of the nanostructured ZnO layers show that the optical properties of these films are typical of ZnO deposited at low temperatures. The results indicate that magnetron sputtering is a viable technique for growing heterostructures and depositing functional layers onto CNTs.

36 MATERIALS SCIENCE↗

Self-organization of SiO{sub 2} nanodots deposited by chemical vapor deposition using an atmospheric pressure remote microplasma

Self-organization of SiO{sub 2} nanodots is obtained by chemical vapor deposition out of hexamethyldisiloxane (HMDSO) and atmospheric pressure remote Ar-O{sub 2} plasma operating at high temperature (1200-1600 K). The dewetting of the film being deposited when it is still thin enough (<500 nm) is found to be partly responsible for this self-organization. When the coating becomes thicker (approx1 mum), and for relatively high contents in HMDSO, SiO{sub 2} walls forming hexagonal cells are obtained on a SiO{sub 2} sublayer. For thicker coatings (>1 mum), droplet-shaped coatings with a Gaussian distribution in thickness over their width are deposited. The coatings are submitted to high compressive stress. When it is relaxed, 'nestlike structures' made of nanoribbons are synthesized.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of krypton atoms on the structure of hydrogenated amorphous carbon deposited by plasma enhanced chemical vapor deposition

Hydrogenated amorphous carbon (a-C:H) films were prepared by plasma enhanced chemical vapor deposition using methane (CH{sub 4}) plus krypton (Kr) mixed atmosphere. The depositions were performed as function of the bias voltage and krypton partial pressure. The goal of this work was to study the influence of krypton gas on the physical properties of a-C:H films deposited on the cathode electrode. Krypton concentration up to 1.6 at. %, determined by Rutherford Back-Scattering, was obtained at high Kr partial pressure and bias of -120 V. The structure of the films was analyzed by means of optical transmission spectroscopy, multi-wavelength Raman scattering and Fourier Transform Infrared spectroscopy. It was verified that the structure of the films remains unchanged up to a concentration of Kr of about 1.0 at. %. A slight graphitization of the films occurs for higher concentration. The observed variation in the film structure, optical band gap, stress, and hydrogen concentration were associated mainly with the subplantation process of hydrocarbons radicals, rather than the krypton ion energy.

36 MATERIALS SCIENCE↗

Texture evolution in nanocrystalline iron films deposited using biased magnetron sputtering

Fe thin films were deposited on sodium chloride (NaCl) substrates using magnetron sputtering to investigate means of texture control in free standing metal films. The Fe thin films were studied using transmission electron microscopy equipped with automated crystallographic orientation microscopy. Using this technique, the microstructure of each film was characterized in order to elucidate the effects of altering deposition parameters. The natural tendency for Fe films grown on (100) NaCl is to form a randomly oriented nanocrystalline microstructure. By careful selection of substrate and deposition conditions, it is possible to drive the texture of the film toward a single (100) orientation while retaining the nanocrystalline microstructure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Influence of deposition temperature of thermal ALD deposited Al{sub 2}O{sub 3} films on silicon surface passivation

The effect of deposition temperature (T{sub dep}) and subsequent annealing time (t{sub anl}) of atomic layer deposited aluminum oxide (Al{sub 2}O3) films on silicon surface passivation (in terms of surface recombination velocity, SRV) is investigated. The pristine samples (as-deposited) show presence of positive fixed charges, Q{sub F}. The interface defect density (D{sub it}) decreases with increase in T{sub dep} which further decreases with t{sub anl} up to 100s. An effective surface passivation (SRV<8 cm/s) is realized for T{sub dep} ≥ 200 °C. The present investigation suggests that low thermal budget processing provides the same quality of passivation as realized by high thermal budget process (t{sub anl} between 10 to 30 min)

36 MATERIALS SCIENCE↗

Improvement of the thermal stability of nickel silicide using a ruthenium interlayer deposited via remote plasma atomic layer deposition

In this study, the effects of a thin Ru interlayer on the thermal and morphological stability of NiSi have been investigated. Ru and Ni thin films were deposited sequentially to form a Ni/Ru/Si bilayered structure, without breaking the vacuum, by remote plasma atomic layer deposition (RPALD) on a p-type Si wafer. After annealing at various temperatures, the thermal stabilities of the Ni/Ru/Si and Ni/Si structures were investigated by various analysis techniques. The results showed that the sheet resistance of the Ni/Ru/Si sample was consistently lower compared to the Ni/Si sample over the entire temperature range. Although both samples exhibited the formation of NiSi{sub 2} phases at an annealing temperature of 800 °C, as seen with glancing angle x-ray diffraction, the peaks of the Ni/Ru/Si sample were observed to have much weaker intensities than those obtained for the Ni/Si sample. Moreover, the NiSi film with a Ru interlayer exhibited a better interface and improved surface morphologies compared to the NiSi film without a Ru interlayer. These results show that the phase transformation of NiSi to NiSi{sub 2} was retarded and that the smooth NiSi/Si interface was retained due to the activation energy increment for NiSi{sub 2} nucleation that is caused by adding a Ru interlayer. Hence, it can be said that the Ru interlayer deposited by RPALD can be used to control the phase transformation and physical properties of nickel silicide phases.

36 MATERIALS SCIENCE↗

Phase Transformation and Water Adsorption Behavior of As‐Deposited and Annealed Ru Metal Thin Films Prepared by Atomic Layer Deposition

ABSTRACT Surfaces play a central role in catalytic processes, and understanding the transformation of ruthenium metal into ruthenium oxide during annealing is essential for tailoring functional catalytic interfaces. In this study, we systematically investigate ≈22 nm thick Ru metal films deposited by atomic layer deposition (ALD) at 300°C, focusing on their chemical composition, structural evolution, and surface hydration behavior following post‐deposition annealing in air from 400 to 600°C. Lab‐based and synchrotron X‐ray photoelectron spectroscopy (XPS) reveal a gradual conversion from metallic Ru to fully oxidized Ru 4+ with increasing annealing temperature, accompanied by a corresponding increase in lattice oxygen. X‐ray diffraction (XRD) shows amorphous Ru oxide phases at 400°C and 500°C that evolve into crystalline RuO 2 at 600°C, while atomic force microscopy (AFM) indicates enhanced grain growth and surface roughening upon annealing. Ambient‐pressure XPS (AP‐XPS) under controlled H 2 O vapor environments (1–17 Torr) demonstrates that samples annealed at 400°C and 500°C exhibit initially high hydroxyl coverage that decreases with increasing water vapor pressure, concurrent with a rise in molecular H 2 O adsorption. In contrast, the crystalline RuO 2 surface formed at 600°C maintains stable hydroxylation and supports increased water uptake. Overall, this work provides fundamental insight into Ru oxide–H 2 O interactions and establishes design principles for engineering oxide surfaces optimized for electrocatalytic applications.

APXPS↗

Structural effects on trends in the deposition and dissolution of metal-supported metal adstructures.

A simple thermodynamic formalism is combined with Density Functional Theory calculations to determine periodic trends in the reversible deposition/dissolution potentials of admetals on a variety of transition metal substrates. For each admetal/substrate combination (81 in total), the deposition/dissolution potential shift (referenced to the corresponding potential of the admetal in its bulk, elemental form) is calculated for isolated adatoms, for dimers, and for more extended kink structures. Clear periodic trends are found for the potential shifts across the space of different admetals and substrates. In addition, for the significant majority of these admetal/substrate systems, the structural effects are found to be a strong function of the local coordination number of the metal atoms, thereby verifying an important assumption that has been widely used in semiempirical models of deposition and dissolution.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Microstructural, chemical and textural characterization of ZnO nanorods synthesized by aerosol assisted chemical vapor deposition

ZnO nanorods were synthesized by aerosol assisted chemical vapor deposition onto TiO{sub 2} covered borosilicate glass substrates. Deposition parameters were optimized and kept constant. Solely the effect of different nozzle velocities on the growth of ZnO nanorods was evaluated in order to develop a dense and uniform structure. The crystalline structure was characterized by conventional X-ray diffraction in grazing incidence and Bragg–Brentano configurations. In addition, two-dimensional grazing incidence synchrotron radiation diffraction was employed to determine the preferred growth direction of the nanorods. Morphology and growth characteristics analyzed by electron microscopy were correlated with diffraction outcomes. Chemical composition was established by X-ray photoelectron spectroscopy. X-ray diffraction results and X-ray photoelectron spectroscopy showed the presence of wurtzite ZnO and anatase TiO{sub 2} phases. Morphological changes noticed when the deposition velocity was lowered to the minimum, indicated the formation of relatively vertically oriented nanorods evenly distributed onto the TiO{sub 2} buffer film. By coupling two-dimensional X-ray diffraction and computational modeling with ANAELU it was proved that a successful texture determination was achieved and confirmed by scanning electron microscopy analysis. Texture analysis led to the conclusion of a preferred growth direction in [001] having a distribution width Ω = 20° ± 2°. - Highlights: • Uniform and pure single-crystal ZnO nanorods were obtained by AACVD technique. • Longitudinal and transversal axis parallel to the [001] and [110] directions, respectively. • Texture was determined by 2D synchrotron diffraction and electron microscopy analysis. • Nanorods have its [001] direction distributed close to the normal of the substrate. • Angular spread about the preferred orientation is 20° ± 2°.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Physical properties of a non-transparent cadmium oxide thick film deposited at low fluence by pulsed laser deposition

Highlights: • A non-transparent cadmium oxide film has been deposited by pulsed laser deposition. • The CdO film is polycrystalline and highly oriented in the (2 0 0) direction. • Thermal treatment was applied in order to see the effect on its physical properties. - Abstract: A stable non-transparent CdO film was grown by pulsed laser deposition. The sample was thermally annealed at 500 °C in air. A (2 0 0) highly oriented polycrystalline film was obtained. The annealed sample has not preferred orientation. Scanning electron micrographs show a grain size reduction for the annealed sample. By Raman spectroscopy, the defects related second order vibrational modes of CdO were observed. Chemical composition analysis shows the presence of CdO together with a substoichiometric CdO{sub x} phase for the as-grown sample. For the annealed sample a compensation of oxygen vacancies was observed. Electrical resistivity measurements give a value of 8.602 × 10{sup −4} (Ω cm) for the as-grown film. For the annealed sample the electrical resistivity increased to a value of 9.996 × 10{sup −3} (Ω cm). Zero transmission has never been reported for CdO films. The photoluminescence spectra were measured in order to shed some light on the origin of the zero transmission.

36 MATERIALS SCIENCE↗

Controlling the structure and ferroic properties of strained epitaxial NiTiO3 thin films on sapphire by post-deposition annealing

Ferroelectrically induced weak ferromagnetism had been predicted earlier in compounds MTiO3 (M = Fe, Mn, Ni) with the LiNbO3-type structure. In order to stabilize this metastable structure by oxide heteroepitaxy, we attempted to grow epitaxial NiTiO3 films on the nonpolar, non-magnetic substrate Al2O3 by pulsed laser deposition. Given the structural imperfections of the as-deposited films arising from the large lattice mismatch, which resulted in weak ferroic ordering, we investigated the effect of post-synthesis annealing on the films’ properties. Our structural data from x-ray diffraction and electron microscopy suggest that the crystalline quality of the NiTiO3 films was greatly improved by annealing the films at 600-1000 oC for 8 hours, with new phase formation along the interface at 1000 oC. Our physical property characterization indicates increased ferromagnetism and polarization after 600 oC, but a change in the magnetic state to likely ferrimagnetism, and a loss of polarization after the 1000 oC treatment. Our results suggest that the ferroic domain properties of the NiTiO3 films can be favorably altered by post-synthesis heat treatment at the proper temperature to manipulate interfacial strain and enhance the multiferroic properties. Improvement in the ferroic properties can be explained by a combination of crystallite growth, interfacial strain relief, and thermodynamic phase stability arguments. At the same time, exceeding temperatures may drive the system to a thermodynamically more favored crystalline order, and eventually to phase segregation and decomposition.

Varga, Tamas↗

Growth and characterization of uranium oxide thin films deposited by polymer assisted deposition

A thin film of uranium oxide was deposited by polymer assisted deposition on a single crystal lanthanum aluminate - strontium aluminum tantalate substrate. The deposition resulted in formation of epitaxial thin film of uranium oxide, which could be attributed to α-U 3 O 8 or α-UO 3 . X-ray diffraction revealed preferential orientation along (100) in case of α-U 3 O 8 or (001) for α-UO 3 for the thin film. A combination of x-ray and neutron reflectometry proved the sample to be α-U 3 O 8 . Furthermore, the film was of 17 nm thickness covered by a capping layer. The less dense capping layer could be a manifestation of surface water adsorbed on the sample.

36 MATERIALS SCIENCE↗

Impact of post deposition annealing in the electrically active traps at the interface between Ge(001) substrates and LaGeO{sub x} films grown by molecular beam deposition

Changes in the electron trapping at the interface between Ge substrates and LaGeO{sub x} films grown by atomic O assisted molecular beam deposition are inferred upon post deposition annealing treatment on the as-deposited films from electrically detected magnetic resonance (EDMR) spectroscopy and from the electrical response of Pt/LaGeO{sub x}/Ge metal oxide semiconductor (MOS) capacitors. The improved electrical performance of the MOS capacitors upon annealing is consistent with the EDMR detected reduction of oxide defects which are associated with GeO species in the LaGeO{sub x} layer as evidenced by x-ray photoelectron spectroscopy.

36 MATERIALS SCIENCE↗