Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Degradation Rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Conductive spinels derived from Co–Mn based alloy precursor for SOFC cathode-side contact application

The utilization of gas-atomized Co–Mn based alloy precursor is a promising approach to lowering the sintering temperature of the spinel contact layer and enhancing its performance. In this work, simulated interconnect/contact/cathode cells are employed to investigate the effects of different metallic precursors (i.e., three Co–Mn based alloy powders and a mixture of Co + MnO 2 powders) on the microstructure and performance of the reactively-sintered MnCo 2 O 4 -based contact layer. While excellent overall electrical performance is observed for all the cells with the four contact precursors during 1000-h testing at 800 °C in air, the cell with the Ce-doped alloy contact precursor shows the lowest cell area specific resistance (ASR) and ASR degradation rate. Cross-sectional observation of the tested cells is conducted to assess the compatibility of the contact layer with adjacent components as well as its effectiveness in reducing the Cr 2 O 3 scale growth and blocking Cr migration from the interconnect to the cathode.

08 HYDROGEN↗
DOE OSTI2020

Next-generation anion exchange membrane water electrolyzers operating for commercially relevant lifetimes

Alkaline anion exchange membrane (AEM) water electrolysis has gained increasing attention due to its potential to achieve low-cost, high performance hydrogen production. However, most existing membranes are not durable in industrial settings. In this work, we demonstrate good performance relative to industrial parameters using Sustainion® anion exchange membranes. Long-duration tests showed stable performance of 1 A/cm 2 at 1.85 V with a degradation rate of less than 1 μV/h over 10,000 h. The projected lifetime is thus over 20 years. Daily on/off cycling performance over the course of 30 years was simulated experimentally through accelerated voltage shock tests, resulting in a performance loss of only 0.15 μV/cycle over 11,000 cycles. As shown through impact and crossover testing, an improvement in performance is achieved by the addition of zirconia to the polymer matrix and mechanically reinforcing the membrane.

08 HYDROGEN↗
DOE OSTI2024

Dynamic operation of metal-supported solid oxide electrolysis cells

Symmetric-structure metal-supported solid oxide fuel cells and electrolysis cells (MS-SOFCs, MS-SOECs) offer several advantages over conventional solid oxide cells, including the use of inexpensive materials, high mechanical strength, and rapid ramp-up ability. Aggressive operation of MS-SOCs in fuel cell mode is well-established, including extremely fast start-up, redox tolerance, and imbalanced pressure. Here, we extend dynamic operation to MS-SOCs in SOEC mode with high steam content for both small button cells and a large rectangular cell, including: steam cycling, thermal cycling, redox cycling and power cycling. Steam cycling entailed switching between 3:97 and 50:50 steam:hydrogen ratio. For thermal cycling, the temperature was rapidly varied between 150°C and 700°C for 50 cycles. Redox cycling involved switching the steam side gas between 50 % humidified H 2 and 50 % humidified N 2 for 5 cycles. Power cycling was performed by operating the cell under variable current density, resulting in cell voltage between 1.3V and 2.8V. Degradation rates for each testing strategy were compared to a baseline cell, and found to be similar. In conclusion, the excellent tolerance to dynamic operation increases confidence that MS-SOECs will be compatible with dynamic or intermittent renewable resources.

08 HYDROGEN↗
DOE OSTI2021

Surface enhanced performance of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ cathodes by infiltration Pr-Ni-Mn-O progress

Herein the present study reports the enhancement of electrochemical oxygen reduction activity of porous La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3–δ (LSCF) cathodes by coating a thin film of Pr-Ni-Mn oxide (PNM5) using a multi-step infiltration process. XRD examination reveals that PNM5 mainly contains a multiphase mixture of Pr 6 O 11 , PrNiO 3 , MnO and NiO. SEM morphology shows a thin PNM5 film and small particles are formed on the surface of LSCF backbone particles. Impedance spectrum analysis indicates that PNM5 infiltrated LSCF exhibits dramatically reduced polarization resistance (R p ), reaching R p of 0.244 Ω cm 2 at 973 K, which is one-half of the baseline LSCF cathode. The activation energy of LSCF cathodes infiltrated with PNM5 is 1.45 eV, slightly lower than the baseline LSCF cathode (1.77 eV). Distribution of relaxation time (DRT) function analysis shows PNM5 infiltration layer significantly promotes the oxygen reduction reaction (ORR) of cathode surface. With the increase in firing temperature, the total resistance increases and R p changes from ion transport to oxygen reduction reaction. Degradation rate of the PNM5-infiltrated LSCF is also lower, 0.02168% vs 0.07093% for the baseline LSCF over a 200-h period. A single cell testing indicated that the peak power density of the PNM5-infiltrated cell was increased by 140.66%. Overall, PNM5 could be a potential catalyst for boosting the performance of a commercial LSCF cathode for solid oxide fuel cells (SOFC).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Gd-doped ceria infiltration into Ni-YSZ on reversible solid oxide cell operation

Gadolinium doped ceria (GDC) infiltration into Ni-(Y 2 O 3 ) 0•08 (ZrO 2 ) 0.92 (Ni-YSZ) fuel electrodes has been shown to significantly improve solid oxide electrolysis cell performance and stability. However, the effects of GDC infiltration on cells operated reversibly between fuel cell and electrolysis modes have not been reported previously. Here we present reversible solid oxide cell life test results for different GDC infiltration loadings into Ni-YSZ electrodes in two types of fuel-electrode-supported solid oxide cells. Electrochemical impedance spectroscopy reveals that GDC infiltrant lowers the initial cell area specific resistance (ASR) and limits the degradation – for example, the GDC-infiltrated electrode ASR increased by 0.1 Ω cm 2 over 1000 h of reversible operation at ±0.5 A cm –2 and 800 °C, compared to 0.19 Ω cm 2 for non-infiltrated cells. Cell voltage degradation rates were reduced by infiltration during operation at a current density of ±0.5 A cm –2 at 800 °C, and during at 700 °C at ±0.75 A cm –2 . Furthermore, scanning electron microscopy observations show that the infiltrated GDC nanoparticles mitigate Ni particle coarsening in the Ni-YSZ electrode, possibly explaining the enhanced cell stability.

25 ENERGY STORAGE↗
DOE OSTI2022

Optimization of metal-supported solid oxide fuel cells with a focus on mass transport

Performance of symmetric-architecture metal-supported solid oxide fuel cells was improved significantly by optimizing the catalyst infiltration process and metal support structure. Optimization of component structure and processing parameters was performed during tape-casting and fabrication of button cells. Mass transport of oxygen in the metal support was identified as a major limitation. To overcome this limitation, pore former loading and thickness of the metal support (130–250 μm) were optimized. The catalyst infiltration process was also improved by studying the impact of firing temperature (400 °C–900 °C) and infiltration cycle numbers (1–15). The maximum power density of the optimized cell was 0.9 W cm –2 at 700°C using hydrogen as a fuel, a three-fold increase over the baseline cell performance. The degradation rate of optimized cells at 550 °C, 600 °C, and 700 °C was 2%, 4.5%, and 5.5% per 100 h, respectively. Here, the phenomena of mass transport, catalyst coarsening, and chromium poisoning on the catalyst were analyzed by electrochemical impedance spectroscopy and scanning electron microscopy.

13 HYDRO ENERGY↗
DOE OSTI2025

Infiltrated electrodes for metal supported solid oxide electrolysis cells

Metal-supported solid oxide cells (MSOCs) are an alternative to conventional solid oxide cells (SOCs) based on ceramic cermets, offering lower material costs and higher operational flexibility. In this study symmetric MSOCs with infiltrated electrodes are explored for steam electrolysis operation to understand the underlying operation and degradation principles and suggest a direction for future MSOCs development. Two different fuel electrode backbones are used: an electronically-conductive lanthanum strontium co-doped iron nickel titanate (LSFNT) infiltrated with cerium-gadolinium oxide (CGO), or an ionic conductive zirconia based backbone (10ScYSZ) infiltrated with Ni:CGO. At the oxygen side, the backbone is 10ScYSZ, which is infiltrated with lanthanum-strontium co-doped cobalt oxide (LSC), or praseodymium oxide as cobalt-free alternative for comparison. This study suggests that the backbone electronic conductivity is key for good electrochemical performance as well as for boosting cell durability. Highly electronically conductive nanoparticles, especially nickel, were observed to irreversibly agglomerate driven by thermal conditions, whereas CGO proved to be a very stable electrocatalyst. At the fuel side, CGO (LSFNT) electrode showed lower ASR and degradation rate than Ni:CGO(ScYSZ) configuration with measured values of 0.50 Ω cm2 and 11 %/1000 h (at 0.60 A/cm2), and 0.70 Ω cm2 and 26 %/1000 h (at 0.50 A/cm2) at 1.30 V, respectively (700 °C, 50 % steam in hydrogen at the fuel side and air at the oxygen electrode side, LSC(ScYSZ) oxygen electrode).

25 ENERGY STORAGE↗
DOE OSTI2025

Effect of high scandium doping in barium zirconate on nickel diffusion and performance of proton-conducting solid oxide electrolyzer cells

Proton-conducting solid oxide electrolyzer cells (p-SOECs) are emerging but promising technologies for hydrogen production. However, due to the lack of a robust electrolyte, p-SOECs struggle simultaneously to display high performance, Faradaic efficiency, and durability. Motivated by its high proton concentrations and stability as a barium zirconate, we have investigated BaZr 0.6 Sc 0.4 O 3-δ (BZSc40) as a potential next-generation p-SOEC electrolyte. Here, we found elevated levels of NiO diffusion through BZSc40 electrolytes during high-temperature sintering, attributed to the large oxygen vacancy concentrations present in BZSc40, as revealed by first-principle computational results. Controlling NiO diffusion is critical, as it can facilitate densification and grain size growth, but it may also detrimentally impact performance by causing electronic leakage. By optimizing sintering temperature when fabricating BZSc40 cells, we successfully controlled NiO diffusion, achieving sufficient electrolyte densification along with high performance and Faradaic efficiency. BZSc40 cells reached −0.99 A/cm 2 at 1.3 V and 600 °C and exhibited enhanced durability with a 3.37 mV/kh degradation rate at −0.8 A/cm 2 over a 200-h testing period. BZSc40 electrolytes demonstrated superior performance over BaZr 0.8 Y 0.2 O 3-δ (BZY20). In addition to elevated current densities and grain sizes, BZSc40 cells achieved Faradaic efficiencies of 76 % compared to 54 % for BZY20 at −0.2 A/cm 2 and 600 °C. This work lays the foundation for BZSc40 as a potential electrolyte due to its advantages over BZY20 while demonstrating the significance of controlling NiO diffusion when fabricating p-SOECs.

Electrolyzer↗
DOE OSTI2023

CdTe-based thin film photovoltaics: Recent advances, current challenges and future prospects

Cadmium telluride (CdTe)-based cells have emerged as the leading commercialized thin film photovoltaic technology and has intrinsically better temperature coefficients, energy yield, and degradation rates than Si technologies. More than 30 GW peak (GWp) of CdTe-based modules are installed worldwide, multiple companies are in production, modules are shipping at up to 18.6% efficiency, and lab cell efficiency is above 22%. We review developments in the science and technology that have occurred over approximately the past decade. These achievements were enabled by manufacturing innovations and scaling module production, as well as maximizing photocurrent through window layer optimization and alloyed CdSe x Te 1-x (CST) absorbers. Improved chlorine passivation processes, film microstructure, and serendipitous Se defect passivation significantly increased minority carrier lifetime. Efficiencies >22% have been realized for both Cu and As doped CST-based cells. The path to further efficiency gains hinges primarily on increasing open circuit voltage (V oc ) and fill factor (FF) through innovations in materials, fabrication methods, and device stacks. Replacing the longstanding Cu doping with As doping is resulting in better module stability and is being translated to large-scale production. To realize 25% efficiency and >1 V V oc , research and development is needed to increase the minority carrier lifetime beyond 100 ns, reduce grain boundary and interface recombination, and tailor band diagrams at the front and back interfaces. Many of these goals have been realized separately however combining them together using scalable manufacturing approaches has been elusive to date. We review these achievements and outstanding opportunities for this remarkable photovoltaic technology.

14 SOLAR ENERGY↗
DOE OSTI2022

Exponential Water Uptake in Ionomer Membranes Results from Polymer Plasticization

Water content is the most influential factor in the performance of ion-exchange membranes (IEMs), controlling their mechanical rigidity, ionic conductivity, and degradation rates. Membranes absorb water exponentially at high water activity (a w ), making that region of the sorption isotherm the most influential on membrane properties. Plasticization of the polymer by water has been proposed to cause this exponential uptake at high a w . However, an integrated microscopic picture of the structure, thermodynamic, and mechanical properties of IEMs as a function of a w has remained elusive. In this work, we use large-scale molecular simulations validated with experimental measurements to compute the sorption isotherms, Young’s modulus, polymer dynamics, and structure of IEMs. The simulations unveil that the exponential increase in water uptake (WU) coincides in all cases with the glass to rubber transition of the membrane, as measured through its Young’s modulus and segmental polymer dynamics. Functionalization of the polymer with alkyl groups further contributes to its plasticization, increasing the WU at a given a w and ion-exchange capacity (IEC). The alkyl chains act synergistically with water to plasticize the polymer matrix and allow water penetration in the membrane. The simulations reveal that the width of the water channels depends on the ratio λ of water to ions in the polymer but is independent of its IEC. We conclude that differences in the polymer matrix–not the water channels–are responsible for the distinct uptake response of IEMs to the thermodynamic driving force of water activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Designing the Platinum Catalyst Layer for Improved Performance and Durability in Anion Exchange Membrane Water Electrolysis

To lower the cost of hydrogen produced by anion exchange membrane water electrolysis (AEMWE), it is critical to reduce the use of platinum group metal (PGM) catalysts within the device. While iridium has been successfully replaced with PGM-free catalysts at the anode, platinum-based (Pt) cathode catalysts are still required to meet the activity and durability targets. This study investigates the impact of commercial Pt/C catalyst loading, ionomer type and content, and electrode fabrication method on the cathode catalyst layer properties and AEMWE performance with the aim of determining the feasibility of reduced Pt loadings. While increased Pt loading is found to improve beginning-of-life performance, the effects are minimal above 0.6 mg/cm 2 . Ink characterization shows that ionomer type and content affect the ink stability, particle size, and percent of unbound ionomer, which further impact the homogeneity of the sprayed catalyst layers. The 5% PiperION cathode exhibited the highest performance, which may be attributed to a balance between the small particle size and the low proportion of unbound ionomer, minimizing kinetic and transport losses. Theoretical calculations show that the ionomers interact differently with the Pt surface, causing different surface charges and water adsorption strength and activating different mechanisms for hydrogen evolution. Pt-PiperION lowered the enthalpy of water-splitting by 0.1 eV compared to Pt alone and allowed for equal site access between adsorbed H* and OH* (both adsorbed at circa −2.2 eV). Although catalyst-coated membrane (CCM) fabrication techniques are desirable for scale-up, no performance enhancement is observed compared with the catalyst-coated substrate approach. Durability, as measured by degradation rates, Pt loss, and catalyst layer restructuring, was found to improve with increased Pt loadings, higher ionomer content, and CCM architectures. These findings provide important insight into the significant role of the cathode in AEMWE and strategies for maintaining the performance with low Pt loading or PGM-free catalysts.

08 HYDROGEN↗
DOE OSTI2026

Enhancing Oxygen Evolution Reaction and Stability in Proton-Conducting Solid Oxide Electrolysis Cells (p-SOECs) via a Porous Gadolinium-Doped Ceria Interlayer

Proton-conducting solid oxide electrolysis cells (p-SOECs) offer a promising pathway for intermediate temperature (400-600 °C) hydrogen production. However, they still face critical challenges related to sluggish oxygen evolution reaction (OER) kinetics and low Faradaic efficiencies. Here, in this work, we demonstrate that introducing a thin (~0.8 µm) porous Gd 0.1 Ce 0.9 O 1.95 (GDC) interlayer between a BaCo 0.8 Zr 0.1 Zn 0.1 O 3-δ (BCZZ) oxygen electrode and electrolyte significantly enhances p-SOEC performance. The GDC interlayer reduces polarization resistance by 48% (0.54 to 0.28 O cm 2 ) and increases Faradaic efficiency from 63% to 81% at -0.8 A/cm 2 and 600 °C. GDC interlayer p-SOECs display elevated effective H 2 current densities compared to control p-SOECs and reach up to -1.22 A/cm 2 at 1.3 V. Mechanistic studies on the interactions between GDC and BCZZ reveal that GDC intrinsically promotes OER kinetics by significantly reducing the polarization activation energy (Ea p ), dropping from 1.45 to 1.22 eV for full p-SOECs and 0.98 to 0.76 eV for symmetric cells. This promotional effect is localized in the electrochemically active region near the electrolyte interface. Durability testing for over 1500 hours under 50% H 2 O conditions indicates that the GDC interlayer also improves long-term stability, with a degradation rate 53% lower than control p-SOECs. By pinpointing the interfacial region where GDC exerts its promotional effect, highlighting its role in enhancing OER kinetics, and establishing interlayer engineering as a powerful technique, this work provides a unified pathway to simultaneously improve p-SOEC activity, Faradaic efficiency, and durability.

08 - HYDROGEN↗
DOE OSTI2023

Effects of the Hydrophobic Block Length Ratio of Poly(vinylbenzyl N -methylpiperidinium carbonate)- b -polyethylene- b -poly(vinylbenzyl N -methylpiperidinium carbonate) Block Copolymers for Anion Exchange Membrane Electrolysis

Electrolysis of water to produce hydrogen from renewable electricity is an extremely attractive strategy to reduce energy dependence on fossil fuels. Development of membrane and ionomer materials that maintain high performance with long lifetimes is needed. We developed and investigated the performance and durability of a series of polyethylene-based ABA triblock copolymer anion exchange ionomer and membrane (AEI, AEM) materials for anion exchange membrane water electrolysis. Poly(vinylbenzyl N-methylpiperidinium carbonate)-b-polyethylene-b-poly(vinylbenzyl N-methylpiperidinium carbonate) was synthesized with different hydrophobic/hydrophilic block ratios (1.02:1, 2.58:1, and 4.46:1) resulting in a range of ion exchange capacities (1.1–1.8 meq g –1 ) and water swelling (23–154%) characteristics. All AEMs showed full anionic dissociation, as evidenced by linear Arrhenius correlations, and excellent carbonate conductivity of 8–94 mS cm –1 at 50 °C. Hydrophilic phase separation may offer superior chemical durability by only wetting the ion-conducting region of the polymer and avoiding attack at the nonwetted backbone. We evaluated the performance and durability of these AEMs as a function of hydrophobic polyethylene (PE) content. The AEM containing the least amount of PE displayed the highest performance of 1 A cm –2 at 2.3 V but degraded at 40 mV h –1 before catastrophically failing after <3 h at 0.5 A cm –2 . With greater PE-containing AEMs, the degradation rate was reduced by 3 orders of magnitude with only a 0.2 V increase in voltage. Constant current electrolysis for 50 h resulted in a voltage change of 0.3 mV h –1 in a single-cell water electrolyzer and 1 M potassium carbonate. In a 600 h test, the voltage change in the final 200 h was impressively low for an experimental film, 58 μV h –1 . Postmortem analysis indicated that the membrane did not thin and that water becomes more tightly hydrogen-bound in the polymer after electrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Enhancing Acidic Oxygen Evolution Activity by Supporting Iridium Electrocatalysts on Tantalum Carbide

For a high-performance proton exchange membrane water electrolyzer (PEMWE), acidic oxygen evolution reaction (OER) electrocatalysts require highly dispersed iridium oxide (IrO x ) nanoparticles. Although carbon-based materials have been explored as promising supports for IrO x nanoparticles, their limited stability under harsh oxidative and acidic PEMWE conditions remains a significant challenge. Here, in this study, we report the synthesis and in situ characterization of active and durable IrOx electrocatalysts supported on electrochemically stable and electrically conducting tantalum carbide (TaC). When applied in a PEMWE, the IrO x /TaC electrocatalyst achieves a cell voltage of 1.71 V at 1.0 A cm –2 , outperforming the commercial IrO 2 catalyst (1.82 V at 1.0 A cm –2 ). Furthermore, the IrO x /TaC catalyst maintains a stable operation for 200 h at 0.5 A cm –2 with a low degradation rate of 36 μV h –1 . Density functional theory calculations further confirm that Ir–O–Ta bond formation at the IrO x /TaC interface reduces the overpotential of the OER compared to IrO 2 . This study underscores the pivotal role of supporting IrO x over stable and conducting metal carbides, providing guidance for the design of advanced acidic OER catalysts.

58 GEOSCIENCES↗
DOE OSTI2021

On the crystallography and reversibility of lithium electrodeposits at ultrahigh capacity

Abstract Lithium metal is a promising anode for energy-dense batteries but is hindered by poor reversibility caused by continuous chemical and electrochemical degradation. Here we find that by increasing the Li plating capacity to high values ( e.g ., 10–50 mAh cm −2 ), Li deposits undergo a morphological transition to produce dense structures, composed of large grains with dominantly (110) Li crystallographic facets. The resultant Li metal electrodes manifest fast kinetics for lithium stripping/plating processes with higher exchange current density, but simultaneously exhibit elevated electrochemical stability towards the electrolyte. Detailed analysis of these findings reveal that parasitic electrochemical reactions are the major reason for poor Li reversibility, and that the degradation rate from parasitic electroreduction of electrolyte components is about an order of magnitude faster than from chemical reactions. The high-capacity Li electrodes provide a straightforward strategy for interrogating the solid electrolyte interphase (SEI) on Li —with unprecedented, high signal to noise. We find that an inorganic rich SEI is formed and is primarily concentrated around the edges of lithium particles. Our findings provide straightforward, but powerful approaches for enhancing the reversibility of Li and for fundamental studies of the interphases formed in liquid and solid-state electrolytes using readily accessible analytical tools.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Predicting synthetic mRNA stability using massively parallel kinetic measurements, biophysical modeling, and machine learning

Abstract mRNA degradation is a central process that affects all gene expression levels, though it remains challenging to predict the stability of a mRNA from its sequence, due to the many coupled interactions that control degradation rate. Here, we carried out massively parallel kinetic decay measurements on over 50,000 bacterial mRNAs, using a learn-by-design approach to develop and validate a predictive sequence-to-function model of mRNA stability. mRNAs were designed to systematically vary translation rates, secondary structures, sequence compositions, G-quadruplexes, i-motifs, and RppH activity, resulting in mRNA half-lives from about 20 seconds to 20 minutes. We combined biophysical models and machine learning to develop steady-state and kinetic decay models of mRNA stability with high accuracy and generalizability, utilizing transcription rate models to identify mRNA isoforms and translation rate models to calculate ribosome protection. Overall, the developed model quantifies the key interactions that collectively control mRNA stability in bacterial operons and predicts how changing mRNA sequence alters mRNA stability, which is important when studying and engineering bacterial genetic systems.

Cetnar, Daniel P.↗
DOE OSTI2026

Organic carbon oxidation state shapes fermentative methanogenic microbiomes and controls greenhouse gas fluxes

Organic compounds with a negative nominal oxidation state of carbon (NOSC) are thermodynamically recalcitrant in anaerobic ecosystems, but few studies have measured the influence of NOSC on carbon degradation rates, gaseous product yields, or microbiome composition. We amended anaerobic rice paddy sediment microcosms with water-soluble monomeric organic carbon compounds varying in NOSC. Consistent with thermodynamic and stoichiometric predictions, negative NOSC compounds are catabolized more slowly but produce more methane per mole of carbon. Negative NOSC microbiomes have higher alpha diversity, more syntrophs and methanogens, and fewer fermentative bacteria. Strikingly, fermentative bacterial taxa display genomically encoded NOSC catabolic preferences both in the lab and field. Negative NOSC-preferring fermenters have longer predicted doubling times, consistent with the thermodynamic recalcitrance of their preferred substrates. We propose that microbial NOSC catabolic preferences may reflect the thermodynamic niche of microorganisms and we anticipate that extending research on microbial catabolic preferences to a greater variety of organic carbon substrates and diverse microbiomes will improve our understanding of microbial carbon cycling and trait evolution.

Hu, Ruiwen↗
DOE OSTI2021

Performance and durability of anion exchange membrane water electrolyzers using down-selected polymer electrolytes

Over the last decade, several stable anion exchange polymer electrolytes have been developed for electrochemical devices. Herein, we investigate how chemical structure and physical properties of polymer electrolytes affect performance and durability of anion exchange membrane water electrolyzers (AEMWEs). We select polymer electrolytes with high alkaline stability and consider their polymer properties including conductivity, mechanical/chemical stability, and material interactions to interpret the performance and durability of AEMWEs. Here, the AEMWE with a poly(phenylene) membrane and a poly(fluorene) ionomeric binder exhibited the best performance among those tested in this study; the AEMWE showed ~1 A cm –2 at 2 V under 1 wt% K 2 CO 3 -fed conditions. The voltage degradation rate was 270–550 μV h –1 for several hundred operating hours at a constant current density of 750 mA cm –2 and a differential pressure of 100 pounds per square inch gauge. Based on these results, we discuss research needs of polymer electrolytes for practical AEMWEs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗