Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Crystal Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Evaluation of Optimum HgZnTe Crystal Growth Parameters and USML-2 Flight Support

Work associated with contract provided support for the approved flight experiment 'Crystal Growth of Selected 2-6 Semiconducting Alloys by Directional Solidification.' General activities included ground-based melt studies, compositional and microstructure characterization of the grown crystals, and participation in the continuing assessment of the program. Specifically, work was performed to determine the optimum furnace translation rate at which a HgZnTe sample could be removed from the crystal growth furnace to avoid shrinkage cavities. Additionally, nine HgZnTe ampoules were prepared and delivered to Marshall Space Flight Center for Ground Control Experiment Laboratory Testing.

Scripa, Rosalia N.↗
NASA NTRS2016

Modeling and Control of Liquid Crystal Imager

In this paper, we present some ideas regarding the modeling and the control aspects of liquid crystal-based imaging systems. We address the challenges of building and deploying a liquid crystal imager by: a) considering the dynamics and control aspects, such as pointing and wavefront error control of large lightweight apertures synthesized by liquid crystal elements, and b) conducting experimental characterization of a prototype electrically-switchable liquid crystal lens.

Quadrelli, Marco B.↗
NASA NTRS1979

Advanced methods for preparation and characterization of infrared detector materials

Crystal growth of Hg sub 1-x Cd sub x Te and density measurements of ingot slices are discussed. Radial compositional variations are evaluated from the results of infrared transmission edge mapping. The pseudo-binary HgTe-CdTe phase diagram is examined with reference to differential thermal analysis measurements. The phase equilibria calculations, based on the 'regular association solution' theory (R.A.S.) are explained and, using the obtained R.A.S. parameters, the activities of Hg, Cd, and Te vapors and their partial pressures over the pseudo-binary melt are calculated.

Lehoczy, S. L.↗
NASA NTRS1983

Advanced methods for preparation and characterization of infrared detector materials

Crystals were prepared by the Bridgman-Stockbarger method with a wide range of crystal growth rates and temperature gradients adequate to prevent constitutional supercooling under diffusion-limited, steady-state, growth conditions. The longitudinal compositional gradients for different growth conditions and alloy compositions were calculated and compared with experimental data to develop a quantitative model of solute redistribution during the crystal growth of the alloys. Measurements were performed to ascertain the effect of growth conditions on radial compositional gradients. The pseudobinary HgTe-CdTe constitutional phase diagram was determined by precision differential-thermal-analysis measurements and used to calculate the segregation coefficient of Cd as a function of x and interface temperature. Experiments were conducted to determine the ternary phase equilibria in selected regions of the Hg-Cd-Te constitutional phase diagram. Electron and hole mobilities as functions of temperature were analyzed to establish charge-carrier scattering probabilities. Computer algorithms specific to Hg(1-x)CdxTe were developed for calculations of the charge-carrier concentration, charge-carrier mobilities, Hall coefficient, and Dermi Fermi energy as functions of x, temperature, ionized donor and acceptor concentrations, and neutral defect concentrations.

Broerman, J. G.↗
NASA NTRS1986

Characterization of hydrogen embrittlement in nickel base superalloy single crystals

In order to study the role of CMSX2 single crystal microstructure on the combined stress-hydrogen environment effects, hydrogen was introduced by cathodic charging. Concentration measurements were carried out to investigate the dependence of hydrogen solubility and trapping on microstructure. Mechanical properties were measured at room temperature on smooth tensile specimens as a function of heat treatment, crystal orientation and H charging conditions. SEM and TEM allow to study H induced cracks initiation and propagation. A large amount of hydrogen can be dissolved and trapped in CMSX2 single crystals when exposed to a high hydrogen fugacity environment. The strong H trapping evidenced in voids explains the predominant role of these defects as crack initiation sites. The strong detrimental effect of hydrogen on the material tenacity is discussed.

Chene, J.↗
NASA NTRS2001

Liquid Crystals Derived from 2-phenyl-isoindoles: Synthesis and Characterization

2-Phenyl-isoindole was investigated as the rigid core unit in a series of asymmetric mesogenic molecules. When the 2-phenyl-isoindole core was terminated with a hexyl tail, no mesophase formation could be observed. When 4-n-(tridecafluorohexyl) was used, however, we observed both monotropic and enantiotropic phase behavior. We found that most functionalities at the anhydride 5-position results in the formation of smectic A (SmA) phases in the temperature range of 70-180 C. Functionalities at the anhydride 4-position suppress mesophase formation. Large substituents (-Br, -NO2) and symmetric substitution patterns (5,6-dichloro, 4,7-dichloro and 4,5,6,7-tetrachloro) on the anhydride moiety increase the melting point and destabilize the mesophase. Temperature dependent X-ray diffraction experiments suggest an interdigitated SmA packing for this family of compounds.

Jow, Kenny G.↗
NASA NTRS2004

Characterization of Individual Aerosol Particles Associated with Clouds (CRYSTAL-FACE)

The aim of our research was to obtain data on the chemical and physical properties of individual aerosol particles from near the bottoms and tops of the deep convective systems that lead to the generation of tropical cirrus clouds and to provide insights into the particles that serve as CCN or IN. We used analytical transmission electron microscopy (ATEM), including energy-dispersive X-ray spectrometry (EDS) and electron energy-loss spectroscopy (EELS), and field-emission electron microscopy (FESEM) to compare the compositions, concentrations, size distributions, shapes, surface coatings, and degrees of aggregation of individual particles from cloud bases and the anvils near the tropopause. Aggregates of sea salt and mineral dust, ammonium sulfate, and soot particles are abundant in in-cloud samples. Cirrus samples contain many H2SO4 droplets, but acidic sulfate particles are rare at the cloud bases. H2SO4 probably formed at higher altitudes through oxidation of SO2 in cloud droplets. The relatively high extent of ammoniation in the upper troposphere in-cloud samples appears to have resulted from vertical transport by strong convection. The morphology of H2SO4 droplets indicates that they had been at least yartiy ammoniated at the time of collection. They are internally mixed with organic materials, metal sulfates, and solid particles of various compositions. Ammoniation and internal mixing of result in freezing at higher temperature than in pure H2SO4 aerosols. K- and S-bearing organic particles and Si-Al-rich particles are common throughout. Sea salt and mineral dust were incorporated into the convective systems from the cloud bases and worked as ice nuclei while being vertically transported. The nonsulfate particles originated from the lower troposphere and were transported to the upper troposphere and lower stratosphere.

Buseck, Peter R.↗
NASA NTRS1997

Photorefractivity in a Titanium Doped ZnCdTe Crystal

Single crystals of Zn(.04)Cd(.96)Te was grown by horizontal physical vapor transport (PVT) method and doped by annealing with TiTe2 powder at 600 C for six days. Photorefractive two-beam coupling, along with photoluminescence and absorption spectroscopy, were used to characterize the ZnCdTe:Ti crystal. At 1.32 micrometers, the photorefractive gain has been measured as a function of the grating period. A gain of about 0.16/cm was obtained at an intensity of about 0.1 W/sq cm. The results of this titanium doped ZnCdTe crystal are compared to that of vanadium-doped CdTe crystals reported previously.

Davis, M.↗
NASA NTRS2018

Deep Space Observations of Sun Glint from Oceans

Every hour or two, the Earth Polychromatic Imaging Camera (EPIC) onboard the DSCOVR satellite provides unique full-color images of the sunlit side of the Earth from the L1 Lagrangian point, which is four times farther the Moon. Casual glances at such images often reveal bright colorful spots that stand out markedly from their surroundings. Such spots often appear not only over ocean but also over land. Tracking the colorful spots using an automated image analysis algorithm reveals that they are caused by specular reflection of sunlight, sometimes from ocean surfaces and other times from clouds containing horizontally oriented ice crystals. The presented study characterizes these spots in terms of prevalence, location, color, and brightness, and provides insights into the factors that lead to their appearance.

ice crystals↗
NASA NTRS2004

Kinetic Roughening and Energetics of Tetragonal Lysozyme Crystal Growth: A Preliminary Atomic Force Microscopy Investigation

We examined particulars of crystal growth from measurements obtained at both microscopic and molecular levels. The crystal growth measurements performed at the microscopic level are well characterized by a model that balances the flux of macromolecules towards the crystal surface with the flux of the crystal surface. Numerical evaluation of model with measurements of crystal growth, in time, provided accurate estimates for the average growth velocities. Growth velocities thus obtained were also interpreted using well-established phenomenological theories. Moreover, we find that microscopic measurements of growth velocity measurements obtained as a function of temperature best characterizes changes in crystal growth modes, when present. We also examined the possibility of detecting a change in crystal growth modes at the molecular level using atomic force microscopy, AFM. From preliminary AFM measurements performed at various supersaturations, we find that magnitude of surface height fluctuations, h(x), increases with supersaturation. Further examination of surface height fluctuations using methods established for fluctuation spectroscopy also enabled the discovery of the existence of a characteristic length, c, which may possibly determine the mode of crystal growth. Although the results are preliminary, we establish the non- critical divergence of 5 and the root-mean-square (rms) magnitude of height-height fluctuations as the kinetic roughening transition temperatures are approached. Moreover, we also examine approximate models for interpreting the non-critical behavior of both 6 and rms magnitude of height-height fluctuations, as the solution supersaturation is increased towards the kinetic roughening supersaturation.

Gorti, Sridhar↗
NASA NTRS1990

The growth of zinc selenide single crystals by physical vapor transport in microgravity

Growth and characterization studies will be performed on zinc selenide single crystals. The high temperature outgassing behavior of the silica ampoule material will be studied in order to develop a cleaning and bake-out procedure that will minimize the amount of impurities introduced into the vapor from the ampoule materials and in particular during the seal-off procedure. The outgassing behavior of the ZnSe starting material will be studied during high vacuum refinement at elevated temperatures in order to develop a temperature pressure program that will optimize the removal of impurities while minimizing a shift in stoichiometry due to preferred evaporation of the higher fugacity component. The mass spectrometer system was completed, and after calibration, will be used to perform the above tasks. The system and its operation is described in detail.

Anderson, Elmer E.↗
NASA NTRS1993

Growth of ZnTe by Physical Vapor Transport and Traveling Heater Method

ZnTe crystals were grown by horizontal physical vapor transport (PVT) and a Te-solution vertical traveling heater method (THM). The grown crystals were examined by X-ray Laue diffraction technique and Hall measurements to determine the growth orientation and the electrical properties of the crystals. They were also characterized by low temperature infrared (IR) absorption measurements. Several sets of distinct peaks were observed in the IR absorption spectra for the THM samples and were identified as resulting from CU(2+) impurities. Similar measurements on vapor grown ZnTe showed featureless absorption spectra. Chemical analyses were carried out to measure the impurity content in various ZnTe samples and synchrotron radiation topography was used to Study crystalline microstructure of the (111) ZnTe single crystals grown by PVT.

Su, Ching-Hua↗
NASA NTRS2000

Preparation and Analysis of RNA Crystals

The crystallization of RiboNucleic Acids (RNA) was studied from the standpoint of mechanisms of crystal growth in three tasks: (1) preparation of high-quality crystals of oligonuclotides for X-ray diffraction, (2) finding pathways to the growth of high-quality crystals for X-ray diffraction and (3) investigation of mechanisms of action of inertial acceleration on crystal growth. In these tasks: (1) RNA crystals were prepared and studied by X-ray diffraction; (2) a pathway to high-quality crystals was discovered and characterized; a combination of kinetic and equilibrium factors could be optimized as described below; and (3) an interplay between purity and gravity was found in a combination of space and ground experiments with nucleic acids and proteins. Most significantly, the rate of concentration of precipitant and RNA can be controlled by membrane-based methods of water removal or by diffusion of multivalent cations across an interface stabilized by a membrane. Oligonucleotide solutions are electrokinetically stabilized colloids, and crystals can form by the controlled addition of multivalent cations.

Todd, Paul↗
NASA NTRSDate not supplied

Detached Melt and Vapor Growth of InI in SUBSA hardware

Indium iodide (InI) single crystals, grown by the Bridgman process, have shown a significant promise as room temperature detector material for X-rays and γ-rays due to the large, close to ideal, bandgap of Eg = 2 eV, and high electrical resistivity. Yet the transport properties of the charge and the detector performance remain inadequate. The Bridgman growth of semiconductor crystals in microgravity have typically resulted in partial dewetting and Marangoni convection, which disturbed the diffusion-controlled growth and produced nonuniform dopant distribution. However, unconfined or partially confined solidification drastically reduced the number of stress-induced defects compared to the confined growth in crucibles on Earth.The goal of the present investigation was to explore melt growth of a heavy metal halide in microgravity, focusing on dewetting, in order to improve the crystalline perfection, i.e., to reduce the number of stress-related defects. InI was chosen because it is non-toxic and has a low melting point of only 365 C (~150 C below the melting point of InSb, used in the SUBSA experiments in 2002). Furthermore, InI melts and evaporates congruently, making it suitable for both growth by directional solidification and growth from the vapor phase. In preparation for the flight experiments, ground-based experiments were conducted in the SUBSA ground unit, consisting of 4 melt growth and 2 vapor growth experiments. The crystals were grown by a gradient freeze method by lowering the setpoint of the furnace. The transparent section of the SUBSA furnace did not allow observations of the solid-liquid interface. Contrary to our expectations, the possible occurrence of dewetting during growth could not be observed. We will present i) the ampoule design and preparation, ii) the experiments conducted in the SUBSA ground unit, iii) the images obtained during the microgravity experiments and iv) the results of the characterization of the grown crystals and detector fabrication.

Crystal Growth↗
NASA NTRS1987

Highly Non-Linear Optical (NLO) organic crystals

This research project involves the synthesis and characterization of organic materials having powerful nonlinear optical (NLO) properties and the growth of highly ordered crystals and monomolecular films of these materials. Research in four areas is discussed: theoretical design of new materials, characterization of NLO materials, synthesis of new materials and development of coupling procedures for forming layered films, and improvement of the techniques for vapor phase and solution phase growth of high quality organic crystals. Knowledge gained from these experiments will form the basis for experiments in the growth of these crystals.

Harris, J. Milton↗
NASA NTRS1974

Influence of gravity-free solidification on microsegregation

Single crystalline germanium has been grown for the first time in space aboard Skylab Mission No. 2. The crystal growth experiment, designed to characterize the influence of gravity-free solidification on microsegregation of a semiconductor material, contained three crystals. One was doped with Ga; the second with Sb; and the third with B. Portions of the germanium crystals were remelted and subsequently resolidified at 5 microns per second under controlled conditions by the gradient freeze technique. Detailed spreading resistance measurements made on the Ga doped Ge crystals indicate that microsegregation in space is reduced by two to five-fold in the bulk and eight-fold near the surface, while macrosegregation in space is reduced by six-fold in the bulk. The effective segregation coefficient for Ga in Ge was analyzed extensively and was found to be larger for space solidification. This has the implication that the solute boundary layer at the growth interface in space is correspondingly thinner. The solidification interface is significantly smoother and is found to be initially convex toward the melt in space. A convective mixing model has been advanced to explain the absence of gravity on convective mixing and solute segregation during solidification.

Yue, J. T.↗
NASA NTRS2014

Crystal Growth of Ternary Compound Semiconductors in Low Gravity Environment

A low gravity material experiment will be performed in the Material Science Research Rack (MSRR) on International Space Station (ISS). There are two sections of the flight experiment: (I) crystal growth of ZnSe and related ternary compounds, such as ZnSeS and ZnSeTe, by physical vapor transport (PVT) and (II) melt growth of CdZnTe by directional solidification. The main objective of the project is to determine the relative contributions of gravity-driven fluid flows to the compositional distribution, incorporation of impurities and defects, and deviation from stoichiometry observed in the grown crystals as results of buoyancy-driven convection and growth interface fluctuations caused by irregular fluid-flows on Earth. The investigation consists of extensive ground-based experimental and theoretical research efforts and concurrent flight experimentation. This talk will focus on the ground-based studies on the PVT crystal growth of ZnSe and related ternary compounds. The objectives of the ground-based studies are (1) obtain the experimental data and conduct the analyses required to define the optimum growth parameters for the flight experiments, (2) perfect various characterization techniques to establish the standard procedure for material characterization, (3) quantitatively establish the characteristics of the crystals grown on Earth as a basis for subsequent comparative evaluations of the crystals grown in a low-gravity environment and (4) develop theoretical and analytical methods required for such evaluations. ZnSe and related ternary compounds have been grown by vapor transport technique with real time in-situ non-invasive monitoring techniques. The grown crystals have been characterized extensively by various techniques to correlate the grown crystal properties with the growth conditions.

Su, Ching-Hua↗
NASA NTRS1988

Electronic materials high-T(sub c) superconductivity polymers and composites structural materials surface science and catalysts industry participation

The fifth year of the Center for Advanced Materials was marked primarily by the significant scientific accomplishments of the research programs. The Electronics Materials program continued its work on the growth and characterization of gallium arsenide crystals, and the development of theories to understand the nature and distribution of defects in the crystals. The High Tc Superconductivity Program continued to make significant contributions to the field in theoretical and experimental work on both bulk materials and thin films and devices. The Ceramic Processing group developed a new technique for cladding YBCO superconductors for high current applications in work with the Electric Power Research Institute. The Polymers and Composites program published a number of important studies involving atomistic simulations of polymer surfaces with excellent correlations to experimental results. The new Enzymatic Synthesis of Materials project produced its first fluorinated polymers and successfully began engineering enzymes designed for materials synthesis. The structural Materials Program continued work on novel alloys, development of processing methods for advanced ceramics, and characterization of mechanical properties of these materials, including the newly documented characterization of cyclic fatigue crack propagation behavior in toughened ceramics. Finally, the Surface Science and Catalysis program made significant contributions to the understanding of microporous catalysts and the nature of surface structures and interface compounds.

Source record↗