SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
HOMAR is computer code using homotopic procedure to produce two-dimensional grids in cross-sectional planes, which grids then stacked to produce quasi-three-dimensional grid systems for aerospace configurations. Program produces grids for use in both Euler and Navier-Stokes computation of flows. Written in FORTRAN 77.
The effect of triangular tabs, placed at the nozzle exit, on the evolution of free jets is investigated. The effect, a large distortion of the jet cross section and a resultant increase in mixing downstream, has been inferred before to be due to a pair of streamwise vortices originating from each tab. In this paper, the generation mechanism of the stream wise vorticity (omega sub x) is considered first. Two sources are postulated. One is the upstream 'pressure hill', produced by the tab, which appears to be the dominant source. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. In the case of a 'delta-tab', a triangular tab with its apex leaning downstream, vorticity from the two sources explain the stronger effect in that configuration. Data on the vorticity evolution for the effect of two delta-tabs are presented, up to twelve jet diameters from the exit, which show that the streamwise vortices persist even at the farthest measurement station. The magnitude of omega sub x-maximum decays continually with distance from the nozzle, its ratio to azimuthal vorticity maximum is found to be about 1/5 everywhere. The relative effect of a delta-tab on jets from an axisymmetric nozzle and a 8:1 rectangular nozzle is also studied. The mixing layer distortion is found to be less pronounced in the rectangular case. The jet mixing, as manifested by the mass flux measured at a downstream station, is increased in the axisymmetric jet but it is decreased in the rectangular jet under consideration by the delta-tab.
The effect of triangular tabs, placed at the nozzle exit, on the evolution of free jets is investigated. The effect, a large distortion of the jet cross section and a resultant increase in mixing downstream, has been inferred before to be due to a pair of streamwise vortices originating from each tab. In this paper, the generation mechanism of the streamwise vorticity (omega sub x) is considered first. Two sources are postulated. One is the upstream 'pressure hill', produced by the tab, which appears to be the dominant source. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. In the case of a 'delta-tab', a triangular tab with its apex leaning downstream, vorticity from the two sources explain the stronger effect in that configuration. Data on the vorticity evolution for the effect of two delta-tabs are presented, up to twelve jet diameters from the exit, which show that the streamwise vortices persist even at the farthest measurement station. The magnitude of omega sub x-maximum decays continually with distance from the nozzle, its ratio to azimuthal vorticity maximum is found to be about 1/5 everywhere. The relative effect of a delta-tab on jets from an axisymmetric nozzle and a 8:1 rectangular nozzle is also studied. The mixing layer distortion is found to be less pronounced in the rectangular case. The jet mixing, as manifested by the mass flux measured at a downstream station, is increased in the axisymmetric jet but it is decreased in the rectangular jet under consideration by the delta-tab.
The understanding and analysis of three dimensional fluid behavior around reentry vehicles, like the Space Shuttle Orbiter, is of considerable importance for flight applications. Vehicle designers need pressure, heat transfer, and shear distributions to support design activities. Traditionally these have been obtained by experimental data. Significant reduction in design costs can be obtained if the calculated results based on finite difference procedures are used to verify and supplement experimental results. Computing the flow field over Space Shuttle Orbiter, which has complex cross sectional geometries is a major problem. A first step in this direction is development of body definition and grid generation procedure. In this project a digitized body definition and grid generation procedure, developed earlier at JSC, is modified and applied to the Shuttle Orbiter X24C-10D. Two dimensional grid and body definition for various sections of the space vehicle is obtained using the differential equation method. This study demonstrates that this geometry and grid generation procedure can be applied to other aerospace vehicles such as aerospaceplanes.
Design trade off studies for 13 different superconducting magnet systems were carried out. Based on these results, preliminary design characteristics were prepared for several superconducting magnet systems suitable for use with a combustion driven MHD generator. Each magnet generates a field level of 8 T in a volume 1.524 m (60 in.) long with a cross section 0.254 m x 0.254 m (10 in. x 10 in.) at the inlet and 0.406 m x .406 m (16 in. x 16 in.) at the outlet. The first design involves a racetrack coil geometry intended for operation at 4.2 K; the second design uses a racetrack geometry at 2.0 K; and the third design utilizes a rectangular saddle geometry at 4.2 K. Each case was oriented differently in terms of MHD channel axis and main field direction relative to gravity in order to evaluate fabrication ease. All cases were designed such that the system could be disassembled to allow for alteration of field gradient in the MHD channel by changing the angle between coils. Preliminary design characteristics and assembly drawings were generated for each case.
Because Jupiter possesses a magnetic field, auroral activity is very likely. The auroral emissions due to electron precipitation are estimated for a model atmosphere with and without helium. The incident primary electrons, which are characterized by representative spectra, are degraded in energy by applying the continuous slow down approximation. All secondaries, tertiaries, and higher generation electrons are assumed to be absorbed locally. A compilation of excitation, dissociation, and ionization cross section data for H, H2, and He are used to model all aspects of the energy deposition process. Volume emission rates are calculated from the total direct excitation rates, and appropriate corrections for cascading are applied. Helium emissions are relatively small because the majority of electrons are absorbed above the region of maximum He concentration.
The vacuum of space presents special problems for optical image sensors. Metallic objects in this environment can produce intense specular reflections and deep shadows. By combining the polarized RCS with an incomplete camera image, it has become possible to better determine the shape of some simple three-dimensional objects. The radar data are used in an iterative procedure that generates successive approximations to the target shape by minimizing the error between computed scattering cross-sections and the observed radar returns. Favorable results have been obtained for simulations and experiments reconstructing plates, ellipsoids, and arbitrary surfaces.
A unique plug-type heat flux gage probe was tested in the NASA Ames Research Center 2x9 turbulent flow duct facility. The probe was fabricated by welding a miniature dual active surface heat flux gage body to the end of a hollow metal cylindrical bolt containing a metal inner tube. Cooling air flows through the inner tube, impinges onto the back of the gage body and then flows out through the annulus formed between the inner tube and the hollow bolt wall. Heat flux was generated in the duct facility with a Huels arc heater. The duct had a rectangular cross section and one wall was fabricated from 2.54 centimeter thick thermal insulation rigid surface material mounted onto an aluminum plate. To measure heat flux, the probe was inserted through the plate and insulating materials with the from of the gage located flush with the hot gas-side insulation surface. Absorbed heat fluxes measured with the probe were compared with absorbed heat fluxes measured with six water-cooled reference calorimeters. These calorimeters were located in a water-cooled metal duct wall which was located across from the probe position. Correspondence of transient and steady heat fluxes measured with the reference calorimeters and heat flux gage probe was generally within a satisfactory plus or minus 10 percent. This good correspondence was achieved even though the much cooler probe caused a large surface temperature disruption of 1000K between the metal gage and the insulation. However, this temperature disruption did not seriously effect the accuracy of the heat flux measurement. A current application for dual active surface heat flux gages is for transient and steady absorbed heat flux, surface temperature and heat transfer coefficient measurements on the surface of an oxidizer turbine inlet deflector operating in a space shuttle test bed engine.
NASA fs investigations of the upper atmosphere and ionosphere require measurements of composition of the neutral air and ions. NASA is able to undertake these observations, but the instruments currently in use have their limitations. NASA has extended the scope of its research in the atmosphere and now requires more measurements covering more of the atmosphere. Out of this need, NASA developed multipoint measurements using miniaturized satellites, also called nanosatellites (e.g., CubeSats), that require a new generation of spectrometers that can fit into a 4 ~4 in. (.10 ~10 cm) cross-section in the upgraded satellites. Overall, the new mass spectrometer required for the new depth of atmospheric research must fulfill a new level of low-voltage/low-power requirements, smaller size, and less risk of magnetic contamination. The Low-Voltage Gated Electrostatic Mass Spectrometer (LVGEMS) was developed to fulfill these requirements. The LVGEMS offers a new spectrometer that eliminates magnetic field issues associated with magnetic sector mass spectrometers, reduces power, and is about 1/10 the size of previous instruments. LVGEMS employs the time of flight (TOF) technique in the GEMS mass spectrometer previously developed. However, like any TOF mass spectrometer, GEMS requires a rectangular waveform of large voltage amplitude, exceeding 100 V -- that means that the voltage applied to one of the GEMS electrodes has to change from 0 to 100 V in a time of only a few nanoseconds. Such electronic speed requires more power than can be provided in a CubeSat. In the LVGEMS, the amplitude of the rectangular waveform is reduced to about 1 V, compatible with digital electronics supplies and requiring little power.
Capsule Parachute Assembly System (CPAS) flight tests regularly stage a helicopter to observe inflation of 116 ft D o ringsail Main parachutes. These side views can be used to generate 3-D models of inflating canopies to estimate enclosed volume. Assuming a surface of revolution is inadequate because reefed canopies in a cluster are elongated due to mutual aerodynamic interference. A method was developed to combine the side views with upward looking HD video to account for non-circular cross sections. Approximating the cross sections as elliptical greatly improves accuracy. But since that correction requires manually tracing projected outlines, the actual irregular shapes can be used to generate high fidelity models. Compensation is also made for apparent tilt angle. Validation was accomplished by comparing perimeter and projected area with known line lengths and/or high quality photogrammetry.
Emissions in the vacuum ultraviolet Lyman-Birge-Hopfield (LBH) bands of N2 were observed at night from the S3-4 spacecraft and from the Space Shuttle. No atmospheric source of this emission was identified. Conway et al. have reported that the intensity of the S3-4 LBH emission varied as the cube power of the N2 or N2O concentration. A vehicle-atmosphere interaction was suggested as the source but it was found that the needed excitation cross section would have to be unacceptably large. Recent models of the gas concentration build-up around large space vehicles predict concentrations that may be consistent with the observe LBH intensity variation with altitude. The emission in the model is generated primarily by secondary collisional excitation by ambient N2 and/or O of desorbed metastable molecular constituents. A Chapman-like production function in the induced gaseous environment results in the observed cube power of the N2 concentration altitude variation. A cross section of approximately 2.5 x 10(-18) sq cm is required for excitation of desorbed metastable N2(A) to the N2 (a 1 Pi g) state to account for the observed intensities.
A panel method is used to calculate incompressible flow about arbitrary three-dimensional inlets with or without centerbodies for four fundamental flow conditions: unit onset flows parallel to each of the coordinate axes plus static operation. The computing time is scarcely longer than for a single solution. A linear superposition of these solutions quite rigorously gives incompressible flow about the inlet for any angle of attack, angle of yaw, and mass flow rate. Compressibility is accounted for by applying a well-proven correction to the incompressible flow. Since the computing times for the combination and the compressibility correction are small, flows at a large number of inlet operating conditions are obtained rather cheaply. Geometric input is aided by an automatic generating program. A number of graphical output features are provided to aid the user, including surface streamline tracing and automatic generation of curves of curves of constant pressure, Mach number, and flow inclination at selected inlet cross sections. The inlet method and use of the program are described. Illustrative results are presented.
Supersonic annular flow passages exist in propulsion applications that include dual combustion ramjet engines where a supersonic annular flow (the outer flow) mixes with a sonic (or supersonic) gas generator flow (the inner flow) in the shock expansion zone downstream of the gas generator nozzle exit. Other engine designs include components in the form of annular ducts whose cross-sectional area varies in the streamwise flow direction. In some of these configurations, it is necessary to support the outer shroud (cowl) by means of struts positioned between the cowl and centerbody. To investigate the distorting influence of these struts on the local flow structure, it is first necessary to ensure that the intrinsic flow without struts is free of wave reflections and the effects of upstream disturbances. It is also necessary to demonstrate that the intrinsic flow exhibits the characteristics of a well-defined turbulent boundary layer flow, so that changes in the local flow structure induced by the presence of struts can be interpreted properly. The purpose of this Note is to demonstrate that a supersonic flow facility that meets these objectives has been developed.
In this paper, we summarize our initial findings from K(a)- and K(u)-band scatterometers which include: a scaling law for backscattered power as a function of rain rate; a linear superposition model for light rains and low wind speeds; evidence of the importance of scattering from rain-generated ring-waves; and progress towards development of a scattering model for computing normalized radar cross sections from wind and rain roughened water surfaces.
A computational procedure for describing transport of electrons in condensed media has been formulated for application to effects and exposures from spectral distributions typical of electrons trapped in planetary magnetic fields. The procedure is based on earlier parameterizations established from numerous electron beam experiments. New parameterizations have been derived that logically extend the domain of application to low molecular weight (high hydrogen content) materials and higher energies (approximately 50 MeV). The production and transport of high energy photons (bremsstrahlung) generated in the electron transport processes have also been modeled using tabulated values of photon production cross sections. A primary purpose for developing the procedure has been to provide a means for rapidly performing numerous repetitive calculations essential for electron radiation exposure assessments for complex space structures. Several favorable comparisons have been made with previous calculations for typical space environment spectra, which have indicated that accuracy has not been substantially compromised at the expense of computational speed.
The Solid Modeling Aerospace Research Tool (SMART) is a computer aided design tool used in aerospace vehicle design. Modeling of structural components using SMART includes the representation of the transverse or cross-wise elements of a vehicle's fuselage, ringframes, and bulkheads. Ringframes are placed along a vehicle's fuselage to provide structural support and maintain the shape of the fuselage. Bulkheads are also used to maintain shape, but are placed at locations where substantial structural support is required. Given a Bezier curve representation of a cross sectional cut through a vehicle's fuselage and/or an internal tank, this project produces a first-guess Bezier patch representation of a ringframe or bulkhead at the cross-sectional position. The grid produced is later used in the structural analysis of the vehicle. The graphical display of the generated patches allows the user to edit patch control points in real time. Constraints considered in the patch generation include maintaining 'square-like' patches and placement of longitudinal, or lengthwise along the fuselage, structural elements called longerons.
The VANS successive approximation numerical method was extended to the computation of three dimensional, viscous, transonic flows in turbomachines. A cross-sectional computer code, which conserves mass flux at each point of the cross-sectional surface of computation was developed. In the VANS numerical method, the cross-sectional computation follows a blade-to-blade calculation. Numerical calculations were made for an axial annular turbine cascade and a transonic, centrifugal impeller with splitter vanes. The subsonic turbine cascade computation was generated in blade-to-blade surface to evaluate the accuracy of the blade-to-blade mode of marching. Calculated blade pressures at the hub, mid, and tip radii of the cascade agreed with corresponding measurements. The transonic impeller computation was conducted to test the newly developed locally mass flux conservative cross-sectional computer code. Both blade-to-blade and cross sectional modes of calculation were implemented for this problem. A triplet point shock structure was computed in the inducer region of the impeller. In addition, time-averaged shroud static pressures generally agreed with measured shroud pressures. It is concluded that the blade-to-blade computation produces a useful engineering flow field in regions of subsonic relative flow; and cross-sectional computation, with a locally mass flux conservative continuity equation, is required to compute the shock waves in regions of supersonic relative flow.
A fast and versatile procedure for algebraically generating boundary conforming computational grids for use with finite-volume Euler flow solvers is presented. A semi-analytic homotopic procedure is used to generate the grids. Grids generated in two-dimensional planes are stacked to produce quasi-three-dimensional grid systems. The body surface and outer boundary are described in terms of surface parameters. An interpolation scheme is used to blend between the body surface and the outer boundary in order to determine the field points. The method, albeit developed for analytically generated body geometries is equally applicable to other classes of geometries. The method can be used for both internal and external flow configurations, the only constraint being that the body geometries be specified in two-dimensional cross-sections stationed along the longitudinal axis of the configuration. Techniques for controlling various grid parameters, e.g., clustering and orthogonality are described. Techniques for treating problems arising in algebraic grid generation for geometries with sharp corners are addressed. A set of representative grid systems generated by this method is included. Results of flow computations using these grids are presented for validation of the effectiveness of the method.