Results for “CT” — Page 10

NASA NTRSDate not supplied

Experimental Observations of Damage States in Unnotched and Notched 3D Orthogonal Woven Coupons Loaded in Tension

This paper describes a series of unnotched and notched tensile tests on two 3D orthogonal woven architectures. Dog bone specimens were used for the unnotched tests, and open-hole specimens were used for the notched tests. For each architecture and test type, two specimens were loaded under monotonic displacement control to failure and two specimens were incrementally loaded to failure in five steps. X-ray computed tomography (CT) was used to characterize the woven architecture and defects on each specimen prior to testing. Digital image correlation (DIC) images were obtained from both sides of the specimen throughout the loading and unloading. Acoustic emission (AE) data were also continuously acquired throughout the loading. For the incremental tests, X-ray CT was used to document the damage progression after each load increment. The damage progression was analyzed based on the results from these three techniques. The results for both architectures and test specimens followed a pattern where matrix cracks formed at the surface perpendicular to the tensile load direction. New surface cracks formed continuously throughout the loading and cracks extended in depth and width. In general, fiber failure was not detected until specimen failure.

Wade C Jackson↗

NASA NTRSDate not supplied

Initial analysis of “stone” size Ryugu samples: current status

As a part of the initial analysis of the Ryugu samples, we perform a variety of analyses of millimeter-sized "stones". Our goals are to elucidate the entire formation process of C-type asteroid Ryugu from the viewpoint of petrology and mineralogy ande obtain necessary information by sample analysis, and then simulate the formation of Ryugu based on the evidencef obtained rom sample analysis. Eighteen stones (8 from Room A and 10 from Room C) were received from the ISAS curation facility on June 1, 2021, and brought into a fully nitrogen-displaced glove box at Tohoku University. At the same time, we also received the powder samples from Room A and Room C. To completely block the atmosphere from leaking into the container, all samples were put in the sample transport containers prepared by ISAS, transferred from the main chamber to the glovebox at ISAS, and then all containers were completely sealed in plastic bags with moisture and oxygen absorbers. No moisture or oxygen was detected when the bags were opened in the glove box at Tohoku University, so it was confirmed that there was no exposure to the atmosphere during transport. To date, a number of analyses have been carried out successfully and almost on schedule. The analysis started with the measurement of reflectance spectra, which are sensitive to atmospheric oxidation, hydroxylation, and adsorbed water. The visible, near-infrared, and mid-infrared reflectance spectra were measured while the samples were kept airtight. The spectra of powder samples and stone samples (as aggregates and as single stone) were successfully obtained. A major feature of the stone team's analysis is the use of synchrotron radiation facilities around the world. Since this analysis is non-destructive, stone samples whose reflectance spectra were measured were sent to KEK, SPring-8, ESRF (France), SOLEIL (France), DESY (Germany), and APS (USA). Using these synchrotron radiation facilities, high spatial resolution and sensitivity XRD, STXM, XANES, CT [1], IR-CT, FT-IR [2, 3], XRF, and Mössbauer analyses were performed. Most of the analyses were carried out under air-tight conditions on the stone samples and the particulates separated from the stone samples. These analyses allowed us to determine the three-dimensional distribution of minerals and elements, redox state, density and porosity of the stone samples. Furthermore, as a characteristic analysis of the stone team, light elemental analysis using negative Muon was performed at the MLF facility of J-PARC with an exceptionally long allocation of machine time. This is the only non-destructive method to measure the concentration of light elements in the whole (not the surface) of stone samples. Because the characteristic X-rays produced by muon irradiation are much higher in energy than the fluorescent X-rays produced by X-ray irradiation, there is little effect of self-absorption by the sample, and therefore, the concentration of light elements such as carbon, oxygen, and Na in the entire "stone" sample can be determined. Some stone samples are currently being measured for heat and strength physical properties in order to understand the physical properties of asteroid Ryugu. The data obtained from these measurements are useful for interpreting the remote-sensing data data taken from the surface layer of the asteroid Ryugu [4-7]. It is also important for understanding the behavior of the Ryugu material during impact events. The surfaces of many stone samples were observed by electron microscopy and other techniques, especially on natural “flat” surfaces formed on 5 stomes. As a result, characteristric mineral aggregates formed by the reactions with water and characteiristic impact features were observed on some of the samples. Based on the observations of surfaces and the synchrotron measurements of the whole stones, important objects such as characteristic structures and specific crystal aggregates for understanding the formation history of the asteroid were identified, and these parts were separated from the stone samples using an Xe beam (pFIB) and analyzed by various methods including transmission electron microscopy and synchrotron radiation analysis. Many stone samples, from which important objects have been separated, are embedded in epoxy resin and cut to produce many polished sections. Electron microscopy and spectroscopic measurements of the polished surfaces are being carried out to reveal the detailed mineralogical properties and elemental distribution inside the stone samples. In the fall, machine time for synchrotron radiation will begin, and we plan to analyze single crystals and characteristic objects separated from the stone samples.

Tomoki Nakamura↗

NASA NTRSDate not supplied

Aqueous alteration of Cb-type asteroid Ryugu

The samples from the asteroid Ryugu, which returned to Earth in the winter of 2020 [1], were stored under pure Nitrogen conditions at the Extraterrestrial Materials Curation Center of ISAS. After basic description [2-3], they were distributed to six initial analysis teams in Japan in June 2021. The initial analysis "Stone" team, which was responsible for the analysis of coarse particles (>1 mm in size), consisted of about 150 scientists from Japan and abroad, and conducted a series of analyses We analyzed sixteen coarse Ryugu particles 1 ~ 8 mm in size: six from the 1st touch-down site and ten from the 2nd touch-down site. Individual coarse samples were cut by Xe-FIB or wire-saw to expose particular objects or textures to be exposed on the surface based on 3D structure and element distribution obtained by synchrotron X-ray CT analysis and XRF analysis, respectively. FE-SEM/EDS and FE-EPMA/WDS analysis were made on all polished sections. TEM observation of many FIB sections was made to see microstructures and to compare with carbonaceous chondrites. Many other analyses were carried out to characterize mineralogical and compositional properties and summary of the analysis procedures is described in [4]. X-ray CT analysis showed that all sixteen Ryugu particles are composed of fine-grained material, with no chondrules and CAIs larger than 100 μm in size. FE-EPMA observation showed that Ryugu samples are breccias, consisting of many small rock fragments of different compositions, lithologies, and histories. The most common lithology includes Mg-rich saponite and serpentine, dolomite, magnesite, hydroxyapatite, pyrrhotite, and magnetite as main constituents. The mineralogy of this major lithology supports the classification of Ryugu samples as CI chondrites, which experienced extensive aqueous alteration in Ryugu’s parent asteroid. Based on the obtained mineralogical properties, we performed chemical modeling of aqueous alteration of Ryugu’s parent asteroid [5]. Numerical simulations [6-8] to reproduce thermal history and impact-induced destruction of the Ryugu’s parent asteroid were also carried out using mineralogical and physical properties of the Ryugu samples. In the talk, I would like to explain the conditions of aqueous alteration occurred in the parent asteroid of Ryugu in order to show how the water in the asteroid changed the mineralogy and chemistry of the nebular dust.

T. Nakamura↗

NASA NTRSDate not supplied

Space Launch System: SLS Real Time Rollout Monitoring for MPCV

The NASA Space Launch System (SLS) rocket, Orion spacecraft, and Mobile Launcher (ML) are transported to Pad 39B from the Vehicle Assembly Building on a large, tracked vehicle known as the Crawler Transporter (CT). The CT is a holdover from the Apollo and Space Shuttle programs but has been extensively upgraded to accommodate the SLS. The Dynamic Rollout Test (DRT) on March 17, 2022 marked the first full rollout of the SLS and ML. Analysis indicated that loads and vibrations would be well below design limits, but out of an abundance of caution it was decided to monitor the response in real time during the rollout to assure that loads remained within predicted limits. This first rollout was outfitted with extensive test instrumentation such as accelerometers, pressure sensors, and strain gauges. This instrumentation remained in place following the integrated vehicle modal test and was being used for additional Operational Modal Analysis (OMA) during the rollout in addition to the real-time monitoring. This presentation discusses the specific loads and accelerations monitored during the rollout, how and why those responses were chosen, and how the system was implemented. Finally, a post-rollout loads reconstruction is used to assess the process and the analysis tools used for the rollout analysis.

SLS↗

NASA NTRSDate not supplied

Three-Dimensional Reconstruction of Defects and Structures in Additively Manufactured Parts with Automated Serial Sectioning

Metal additive manufacturing (AM) processes have been demonstrated to be effective at reducing costs and lead times associated with complex components for space flight applications. Laser powderbed fusion (L-PBF) is a commonly used AM technology due to the ability to produce complex parts with fine feature resolution in a wide variety of alloys and applications. L-PBF, like many other manufacturing processes, can produce minor flaws in parts when in nominal operation as well as process-escape defects when process abnormalities occur. The effects of the flaws and methods of detecting the flaws are a subject of interest to understand the difficulties in detecting these flaws with current technology and how much risk the flaws or defects pose to potential flight parts. Using a RoboMet.3D automated serial sectioning system, seeded defects as well as minor process flaws can be imaged and reconstructed in three dimensions to compare to non-destructive evaluation (NDE) techniques, such as x-ray computed tomography (CT), neutron CT, and in-situ monitoring. The RoboMet automates the metallography process by automatically grinding, polishing, and imaging samples in a single system and providing the control data for NDE comparisons to know the real size of defects built into coupons. These comparisons provide an understanding behind the technological limitations of the NDE techniques for different alloys. The same serial sectioning methods have also been utilized to characterize the surfaces of parts to reconstruct the surfaces and take measurements of internal features not easily examined with non-destructive methods. Using the RoboMet, fine lattice structures built with L-PBF have been characterized to determine the actual thicknesses of struts and density of the lattice structures. These structures have been used as finer build supports for the L-PBF process, designs for fine catalysts, and other design considerations for small components. The RoboMet data helps to inform the modeling and design efforts around these fine components.

additive manufacturing↗

NASA NTRSDate not supplied

In-situ Imaging of Pyrolyzing Aerospace Materials

Tracking morphological changes of materials during heating is crucial to understand its response in fire protection, biofuel production, thermal protection systems (TPS) for hypersonic flight. As materials are heated, they undergo physical and chemical changes due to water loss, stretching or shrinking, pyrolysis and chemical reactions in the ambient environment. The effects of these changes can have a profound impact on the material’s performance, indicated by changes in on the porosity and volume. While materials such as wood shrink as they pyrolyze and lose mass, others swell due to their inherent characteristics when exposed to heat [1]. This study focuses on experiments conducted at the Advanced Light Source (ALS) beamline 8.3.2, where in situ micro-computed tomography (µ-CT) is performed on materials as they are being pyrolyzed. Through in situ µ-CT, the change in total volume and porosity can be obtained in real-time, allowing for better understanding of the underlying thermophysical and chemical processes as a function of temperature. This study also focuses on the implementation of the Porous Microstructure Analysis software (PuMA) [2] to obtain thermal conductivity, permeability, and other properties of the material from the 3D tomographies. The information gained from these tomographies will supplement microscale model development of material morphological change and will aid macroscale modeling for high-temperature applications. For this study, Room Temperature Vulcanizing silicone (RTV) [3-5] is heated from room temperature to 1000°C using an infrared lamp heating system, and tomographies are continuously collected as the sample is heated. The tomographies are then segmented to obtain solid and void phases, from which estimates of pore size, porosity and total volume are extracted as a function of temperature. PuMA is deployed on the segmented tomographies to obtain thermal conductivity, permeability, and other properties as a function of temperature. Preliminary results show that RTV first intumesces (swells) as pyrolysis begins, due to build-up of pyrolysis gases in closed pores, and then shrinks significantly as more open pores are formed and the pyrolysis gases outgas. Pore network visualization of the tomographies using OpenPNM [6] showed the increase in pore connectivity with increase in temperature. Future work will focus on using PuMA to obtain macroscopic properties of RTV as a function of temperature.

Tomography↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

The present computational study investigates the aerodynamic design and analysis of cruise slotted wings with natural laminar flow for transonic transport aircraft. The cruise slotted wing is a multielement wing concept that features an intermediate slot to achieve greater aft loading relative to supercritical wings for the potential benefit of reduced shock strength and pressure drag. Transonic near-cruise, off-design assessments have also shown improved drag rise characteristics due to the ability of the slot to mitigate boundary layer separation on the aft flap component. However, due to the decreased Reynolds number of the flap, the cruise slotted wing has historically incurred a skin-friction drag penalty relative to a conventional supercritical wing. To offset this penalty, a cruise slotted wing with the forward main element and aft flap element shaped to achieve natural laminar flow is desired. Toward this effort, a knowledge-based aerodynamic design method, CDISC, has been leveraged to design a partial-span cruise slotted wing with natural laminar flow for a Mach-0.8 variant of the Common Research Model. Drag comparisons will be provided at cruise and near-cruise, off-design conditions relative to both fully turbulent and natural laminar flow conventional wing designs. It is anticipated that pairing natural laminar flow technology with the cruise slotted wing architecture will allow for cruise drag performance similar to conventional laminar flow wings with improved drag rise characteristics and more limited laminar-flow sensitivity at off-design conditions. Preliminary results for a cruise slotted wing with laminar flow on the outboard wing section only have shown a 10-ct cruise drag reduction relative to a conventional supercritical wing, but a 8-ct penalty relative to the conventional NLF wing. The final paper will include results for a cruise slotted wing design with laminar flow on both the inboard and outboard wing sections.

CFD↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

The present computational study investigates the aerodynamic design and analysis of cruise slotted wings with natural laminar flow for transonic transport aircraft. The cruise slotted wing is a multielement wing concept that features an intermediate slot to achieve greater aft loading relative to supercritical wings for the potential benefit of reduced shock strength and pressure drag. Transonic near-cruise, off-design assessments have also shown improved drag rise characteristics due to the ability of the slot to mitigate boundary layer separation on the aft flap component. However, due to the decreased Reynolds number of the flap, the cruise slotted wing has historically incurred a skin-friction drag penalty relative to a conventional supercritical wing. To offset this penalty, a cruise slotted wing with the forward main element and aft flap element shaped to achieve natural laminar flow is desired. Toward this effort, a knowledge-based aerodynamic design method, CDISC, has been leveraged to design a partial-span cruise slotted wing with natural laminar flow for a Mach-0.8 variant of the Common Research Model. Drag comparisons will be provided at cruise and near-cruise, off-design conditions relative to both fully turbulent and natural laminar flow conventional wing designs. It is anticipated that pairing natural laminar flow technology with the cruise slotted wing architecture will allow for cruise drag performance similar to conventional laminar flow wings with improved drag rise characteristics and more limited laminar-flow sensitivity at off-design conditions. Preliminary results for a cruise slotted wing with laminar flow on the outboard wing section only have shown a 10-ct cruise drag reduction relative to a conventional supercritical wing, but a 8-ct penalty relative to the conventional NLF wing. The final paper will include results for a cruise slotted wing design with laminar flow on both the inboard and outboard wing sections.

Natural Laminar Flow↗

NASA NTRSDate not supplied

Fabrication and Characterization of A Lunar Simulant-Based Sintered Construction Material

In-situ resource utilization (ISRU) is critical to enable future efforts to have a long-term human presence on the Moon as well as Mars. ISRU technologies are being developed for radiation protection, dust mitigation, thermal insulation, and other applications. One such ISRU technology for creating construction materials out of lunar and Martian regolith is sintering, which is a thermal-based construction process that bonds finely grained material together at temperatures below the melting point. However, the conditions employed during the sintering, such as temperature, atmospheric composition, duration of the process, and pressure, can have a significant impact on the quality and strength of the resulting materials. In parallel, the development of methods for characterizing the quality, porosity, density, and other properties of these materials is critical. X-ray computed tomography (X-ray CT) can image large changes in density within a material, such as the presence of pores throughout an otherwise uniform medium, with relatively high spatial resolution. Similarly, Terahertz time-domain spectroscopic (THz-TDS) imaging is sensitive to density variations within samples, but is restricted to non-conducting materials. Specifically, previous work has shown that the refractive index (n eff ) values obtained through the analysis of THz-TDS images increases with increasing density within plastic samples. Even further, this work showed that it is possible to create a calibration curve for a given material from samples of different, but known density, which can enable one to directly convert n eff to density for samples having the same composition, but unknown density. Here, we report on the fabrication of a lunar simulant-based sintered construction material using vacuum hot pressed (VHP) sintering, then show X-ray CT and THz-TDS imaging results of the sample, which show spatial variations in the material. This has important implications for efforts to improve these types of lunar construction material processes and verify the quality of these materials in terms of consolidation. To the best of our knowledge, there is no previous work utilizing VHP sintering to make lunar simulant-based construction materials or exploring the feasibility of THz imaging to spatially map the density variation through a lunar simulant-based construction material.

Terahertz time-domain spectroscopic imaging↗

NASA NTRSDate not supplied

Thermo-Poro-Mechanical Modeling of RTV Intumescence

Room temperature vulcanizing (RTV) silicone is a high-temperature adhesive used as a gap-filler between heatshield tiles in numerous entry missions. Its propensity to intumesce, or swell upon exposure to heat, is a well-known effect that needs to be carefully quantified during design. At tile interfaces of charring ablators, intumescence, combined with differential recession, could cause the gap filler to protrude past the ablator outer mold line, forming a “fence”. Fencing can in turn cause transition to turbulence of the flow wetting the heat shield, leading to augmented surface heating. Recent experiments conducted at the Plasmatron X facility, the high enthalpy wind tunnel of the Center for Hypersonics and Entry Systems Studies, have shown prominent fencing of RTV gap fillers in PICA, under both nitrogen and air plasmas. Similar observations are well known in the arcjet literature. Further experiments under controlled environment, performed using in situ X-ray micro-computed tomography (micro-CT) at the Advanced Light Source (ALS), have shown heating rate-dependent swelling and shrinkage of RTV during pyrolysis. To simulate RTV intumescence, a novel model was introduced in the Porous Materials Analysis Toolbox based on OpenFOAM, PATO, to account for pore-pressure buildup within both closed- and open-pores. The governing equation for the thermo-poro-mechanical response were developed, assuming linear elasticity for the charring silicone. A new multi-pyrolysis model that tracks non-monotonic advancement of material properties with pyrolysis was proposed. This model addresses the limitations of state-of-the-art ablator models to capture the different stages of thermal degradation and coupled thermomechanics. Swelling of RTV was simulated using the new thermo-poro-mechanical model and compared against in situ micro-CT data. Results showed good agreement in intumescence height and temperature profiles at all heating rates, indicating that the key factor contributing to RTV swelling is the internal pressure build-up within closed- and open-pores. As RTV is cured into a soft (rubbery) compound with low-porosity and permeability, initial temperature increase and pyrolysis gas production cause a significant increase of internal pressure, causing a pronounced volume growth. As thermal degradation progresses, rigidization of the silicone occurs due to char hardening which counteract volume shrinkage after gas pressure relief. Overall, our model shows that accounting for changes in properties such porosity, permeability and key thermomechanical coefficients is crucial for capturing the RTV volume change during ablation and enable a predictive capability for heatshield tile interface response. A plan for future calibration of thermomechanical properties evolution during degradation is discussed, as a key next step to close the new model.

RTV↗

NASA NTRSDate not supplied

Thermo-Poro-Mechanical Modeling of RTV Intumescence

Room temperature vulcanizing (RTV) silicone is a high-temperature adhesive used as a gap-filler between heatshield tiles in numerous entry missions. Its propensity to intumesce, or swell upon exposure to heat, is a well-known effect that needs to be carefully quantified during design. At tile interfaces of charring ablators, intumescence, combined with differential recession, could cause the gap filler to protrude past the ablator outer mold line, forming a “fence”. Fencing can in turn cause transition to turbulence of the flow wetting the heat shield, leading to augmented surface heating. Recent experiments conducted at the Plasmatron X facility, the high enthalpy wind tunnel of the Center for Hypersonics and Entry Systems Studies, have shown prominent fencing of RTV gap fillers in PICA, under both nitrogen and air plasmas. Similar observations are well known in the arcjet literature. Further experiments under controlled environment, performed using in situ X-ray micro-computed tomography (micro-CT) at the Advanced Light Source (ALS), have shown heating rate-dependent swelling and shrinkage of RTV during pyrolysis. To simulate RTV intumescence, a novel model was introduced in the Porous Materials Analysis Toolbox based on OpenFOAM, PATO, to account for pore-pressure buildup within both closed- and open-pores. The governing equation for the thermo-poro-mechanical response were developed, assuming linear elasticity for the charring silicone. A new multi-pyrolysis model that tracks non-monotonic advancement of material properties with pyrolysis was proposed. This model addresses the limitations of state-of-the-art ablator models to capture the different stages of thermal degradation and coupled thermomechanics. Swelling of RTV was simulated using the new thermo-poro-mechanical model and compared against in situ micro-CT data. Results showed good agreement in intumescence height and temperature profiles at all heating rates, indicating that the key factor contributing to RTV swelling is the internal pressure build-up within closed- and open-pores. As RTV is cured into a soft (rubbery) compound with low-porosity and permeability, initial temperature increase and pyrolysis gas production cause a significant increase of internal pressure, causing a pronounced volume growth. As thermal degradation progresses, rigidization of the silicone occurs due to char hardening which counteract volume shrinkage after gas pressure relief. Overall, our model shows that accounting for changes in properties such porosity, permeability and key thermomechanical coefficients is crucial for capturing the RTV volume change during ablation and enable a predictive capability for heatshield tile interface response. A plan for future calibration of thermomechanical properties evolution during degradation is discussed, as a key next step to close the new model.

silicone intumescence↗

NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook - Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. Techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delaminations, voids, Automated Fiber Placement (AFP) defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency and limitations. This presentation will describe key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability to the NDE community of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members is discussed.

Nondestructive Evaluation↗

NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook - Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. Techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delaminations, voids, Automated Fiber Placement (AFP) defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency and limitations. This paper describes key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability to the NDE community of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members is discussed.

nondestructive evaluation↗

NASA NTRS1975

The geometric approach to sets of ordinary differential equations and Hamiltonian dynamics

The calculus of differential forms is used to discuss the local integration theory of a general set of autonomous first order ordinary differential equations. Geometrically, such a set is a vector field V in the space of dependent variables. Integration consists of seeking associated geometric structures invariant along V: scalar fields, forms, vectors, and integrals over subspaces. It is shown that to any field V can be associated a Hamiltonian structure of forms if, when dealing with an odd number of dependent variables, an arbitrary equation of constraint is also added. Families of integral invariants are an immediate consequence. Poisson brackets are isomorphic to Lie products of associated CT-generating vector fields. Hamilton's variational principle follows from the fact that the maximal regular integral manifolds of a closed set of forms must include the characteristics of the set.

Estabrook, F. B.↗

NASA NTRS1979

Some aspects of a free jet phenomena to 105 L/D in a constant area duct

Under certain conditions, inlets with a Borda type geometry were shown to exhibit sufficiently strong separation effects to permit the working fluid to flow through the duct as if it were a free jet. Mass limiting flow data and associated pressure profiles for tubes of 14, 53, 64, 73, and 105 L/D with a Borda type inlet were taken to determine bounds of the free jet phenomena. For a given tube roughness, the limits appear to be one dimensional and dependent only on inlet stagnation conditions. For smooth tubes the upper L/D boundary is related by P sub R roughly equal to CT to the 17th power and sub R, C roughly equal to 00017 (L/D) to the 2.5 power where F sub R = P/P sub c is reduced pressure and T sub R = T/T sub c is reduced temperature. The lower bound appears to be saturation conditions at the inlet. Similar free jet effects were found for fluid hydrogen indicating that fluid jetting may be common to all fluids. While limited data on surface roughness show a decrease in the upper L/D limit, nevertheless fluid jetting still occurred.

Hendricks, R. C.↗

NASA NTRS1979

Spectra of Fe-Ti silicate glasses - Implications to remote-sensing of planetary surfaces

Optical spectra of synthetic Fe-Ti silicate glasses and the temperature variations of the spectral features were investigated. The spectra are assigned to absorptions due to crystal field (CF) transitions in Ti(3+), Fe(2+) in octahedral coordination, and Fe(2+) in tetrahedral coordination, and to metal-metal and oxygen-metal charge transfer (CT) transitions which contribute to the near ultraviolet absorption edge. Temperature variations of the optical bands have been studied to explore implications for remote sensing. Caution is urged in the use of the absorption edge as a measure of TiO2 concentrations on planetary surfaces and in regolith samples.

Nolet, D. A.↗

NASA NTRS1982

Use of optimization to predict the effect of selected parameters on commuter aircraft performance

The relationships between field length and cruise speed and aircraft direct operating cost were determined. A gradient optimizing computer program was developed to minimize direct operating cost (DOC) as a function of airplane geometry. In this way, the best airplane operating under one set of constraints can be compared with the best operating under another. A constant 30-passenger fuselage and rubberized engines based on the General Electric CT-7 were used as a baseline. All aircraft had to have a 600 nautical mile maximum range and were designed to FAR part 25 structural integrity and climb gradient regulations. Direct operating cost was minimized for a typical design mission of 150 nautical miles. For purposes of C sub L sub max calculation, all aircraft had double-slotted flaps but with no Fowler action.

Wells, V. L.↗

NASA NTRS1983

Computed tomographic analysis of meteorite inclusions

The feasibility of obtaining nondestructively a cross-sectional display of very dense heterogeneous rocky specimens, whether lunar, terrestrial or meteoritic, by using a fourth generation computed tomographic (CT) scanner, with modifications to the software only, is discussed. A description of the scanner, and of the experimental and analytical procedures is given. Using this technique, the interior of heterogeneous materials such as Allende can be probed nondestructively. The regions of material with high and low atomic numbers are displayed quickly; the object can then be cut to obtain for analysis just the areas of interest. A comparison of this technique with conventional industrial and medical techniques is made in terms of image resolution and density distribution display precision.

Arnold, J. R.↗