Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSOR BLADE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 2: Data and performance for stage A

Stage A, comprised of a conventional rotor and stator, was designed and tested to establish a performance baseline for comparison with the results of subsequent tests planned for two tandem-blade stages. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. At design equivalent rotor speed, rotor A achieved a maximum adiabatic efficiency of 85.1 percent at a pressure ratio of 1.29. The stage maximum adiabatic efficiency was 78.6 percent at a pressure ratio of 1.27.

Brent, J. A.↗
NASA NTRS1972

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 3: Data and performance for stage C

Stage C, comprised of tandem-airfoil rotor C and tandem-airfoil stator B, was designed and tested to establish performance data for comparison with the performance of conventional single-airfoil blading. Velocity diagrams and blade leading and trailing edge metal angles selected for the conventional rotor and stator blading were used in the design of the tandem blading. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. At design equivalent rotor speed, rotor C achieved a maximum adiabatic efficiency of 91.8% at a pressure ratio of 1.31. The stage maximum adiabatic efficiency was 86.5% at a pressure ratio of 1.31.

Brent, J. A.↗
NASA NTRS1972

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 1: Analysis and design of stages A, B, and C

A conventional rotor and stator, two dual-airfoil tandem rotors, and one dual-airfoil tandem stator were designed. The two tandem rotors were each designed with different percentages of the overall lift produced by the front airfoil. Velocity diagrams and blade leading and trailing edge metal angles selected for the conventional rotor and stator blading were used in the design of the tandem blading. Rotor inlet hub/tip ratio was 0.8. Design values of rotor tip velocity and stage pressure ratio were 757 ft/sec and 1.30, respectively.

Brent, J. A.↗
NASA NTRS1992

Numerical simulation of compressor endwall and casing treatment flow phenomena

A numerical study is presented of the flow in the endwall region of a compressor blade row, in conditions of operation with both smooth and grooved endwalls. The computations are first compared to velocity field measurements in a cantilevered stator/rotating hub configuration to confirm that the salient features are captured. Computations are then interrogated to examine the tip leakage flow structure since this is a dominant feature of the endwall region. In particular, the high blockage that can exist near the endwalls at the rear of a compressor blade passage appears to be directly linked to low total pressure fluid associated with the leakage flow. The fluid dynamic action of the grooved endwall, representative of the casing treatments that have been most successful in suppressing stall, is then simulated computationally and two principal effects are identified. One is suction of the low total pressure, high blockage fluid at the rear of the passage. The second is energizing of the tip leakage flow, most notably in the core of the leakage vortex, thereby suppressing the blockage at its source.

Crook, A. J.↗
NASA NTRS1972

Reynolds number effect on overall performance of a 10.8-centimeter (4.25-inch) sweptback bladed centrifugal compressor

The performance data were taken at 50,000 rpm, using argon gas. As the Reynolds number was reduced from near design value to 30 percent of design, the maximum efficiency decreased about 1.5 percentage points. Reducing the Reynolds number from 30 percent to approximately 10 percent of design caused the maximum efficiency to decrease another 2.5 percentage points. The variation in loss with Reynolds number is compared with inverse power relation of loss with Reynolds number.

Weigel, C.↗
NASA NTRS1980

Three dimensional mean flow and turbulence characteristics of the near wake of a compressor rotor blade

The investigation was carried out using the rotating hot wire technique. Measurements were taken inside the end wall boundary layer to discern the effect of annulus and hub wall boundary layer, secondary flow, and tip leakage on the wake structure. Static pressure gradients across the wake were measured using a static stagnation pressure probe insensitive to flow direction changes. The axial and the tangential velocity defects, the radial component of velocity, and turbulence intensities were found to be very large as compared to the near and far wake regions. The radial velocities in the trailing edge region exhibited characteristics prevalent in a trailing vortex system. Flow near the blade tips found to be highly complex due to interaction of the end wall boundary layers, secondary flows, and tip leakage flow with the wake. The streamwise curvature was found to be appreciable near the blade trailing edge. Flow properties in the trailing edge region are quite different compared to that in the near and far wake regions with respect to their decay characteristics, similarity, etc. Fourier decomposition of the rotor wake revealed that for a normalized wake only the first three coefficients are dominant.

Ravindranath, A.↗
NASA NTRS1981

The boundary layer on compressor cascade blades

Some redesign of the cascade facility was necessary in order to incoporate the requirements of the LDA system into the design. Of particular importance was the intended use of a combination of suction upstream of the blade pack with diverging pack walls, as opposed to blade pack suction alone, for spanwise dimensionality control. An ARL blade was used to redo some tests using this arrangement. Preliminary testing and boundary layer measurements began on the double circular arc blades.

Deutsch, S.↗
NASA NTRS1981

Interaction of compressor rotor blade wake with wall boundary layer/vortex in the end-wall region

This paper reports the experimental study of the three-dimensional characteristics of the mean velocity of the rotor wake inside the annulus- and hub-wall boundary layers. The measurements were taken with a rotating three-sensor hot wire behind the rotor. This set of measurements probably represents the first set of comprehensive measurements taken inside the annulus- and hub-wall boundary layers. The wake was surveyed at several radial locations inside the boundary layer region and at several axial locations. Interaction of the wake with the annulus-wall boundary layer, secondary flow, tip-leakage flow, and the trailing vortex system results in slower decay and larger width of the wake. The presence of a strong vortex and its merger with the wake is also observed. The end-wall boundary layers and the secondary flow were found to have a substantial effect on both the decay characteristics and the profile of the wake. These and other measurements are reported and interpreted in this paper.

Lakshminarayana, B.↗
NASA NTRS1986

Case histories involving fatigue and fracture mechanics; Proceedings of the Symposium, Charleston, SC, Mar. 21, 22, 1985

Papers are presented on cracking at nozzle corners in the nuclear pressure vessel industry, applied fracture mechanics for assessing defect significance in a crude oil pipeline, failure analysis of a large wind-tunnel compressor blade, analysis of a compressor-wheel failure, and preventing fracture by inspection and analysis. Consideration is also given to the fatigue crack growth predictions of welded aircraft structures containing flaws in the residual stress field, the fatigue and fracture mechanics analysis of a compression loaded aircraft structure, fracture of an aircraft horizontal stabilizer, fatigue life analysis of fuel tank skins under combined loads, and aircraft structural maintenance recommendations based on fracture mechanics analysis. Additional papers discuss an analysis of two metal-forming die failures, an analysis of a failed saw arbor, and the role of fracture mechanics in assessing the effect on fatigue life of design changes in welded fabrications.

Hudson, C. Michael↗