SEARCH · Engineering Papers

Results for “CFD simulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Experimental and Theoretical Evaluation of Feed Flow Collar Design for Shell Fed Hollow Fiber Membrane Modules

An experimental and theoretical study of module collar design is presented here. Hollow fiber membranes are prepared by dip coating a poly(vinylidene) (PVDF) support with a polydimethylsiloxane (PDMS) gutter layer and a Pebax 2533 selective layer. Fiber bundles with a well-defined fiber packing are prepared using a 3D printed module. A parallel fiber bundle consisting of 4-9 uniformly spaced fibers is created with printed tabs that align the fibers and create a tubesheet. The tabs are sealed within a printed case that possesses a series of external ports for gas introduction and removal. Uniquely, both port location and the use of a collar to assist fluid distribution in the shell can be varied for the same fiber bundle. Experimental measurements are compared to computational fluid dynamics (CFD) simulations. The experimental module design allows high-fidelity representation of the fiber bundle and module case in the simulations. Comparisons between experiment and simulation are in good agreement over a broad range of experimental conditions. The detrimental effect of having ports located too close, leading to stagnation regions, is captured as well as the beneficial effects of using a collar for shell-side fluid distribution around the fiber bundle. Such results help validate the use of CFD to develop high-performance module designs.

Tran, Thien↗

DOE OSTI2020

ECAR-5067 Computational Evaluation on Effect of Edge-rounding in Circular to Annular Flow Transitions within a Hexagonal Duct

In this ECAR, the computational fluid dynamics (CFD) simulation of the duct with a cross-section varying from circle to annulus was performed to evaluate the effect of edge-rounding of the internal edges. The edge of circular channel and the edge of inner annular channel were rounded with the radius of curvature ranged from 0 mm to 20 mm. The CFD results show that the pressure loss of the duct can be reduced by increasing the radius of the rounded edge. Case-A results showed that the pressure drop can be significantly reduced by the edge-rounding, e.g., the pressure drop was reduced approximately 56% by the radius of curvature of 5.0mm, and reduced 70% by the radius of curvature of 20.0 mm although its effectiveness would be attenuated as the radius of curvature of edge increases. Results from Case-B showed the impact of rounding the inlet edge was practically negligible compared to the outlet edge. This ECAR could provide a guideline to determine the optimum inlet module design of the VTR fuel rod bundle.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2022

Parametric Study of Panel PCM–Air Heat Exchanger Designs

Heat exchangers, devices for the transfer of heat between two or more working fluids, are extensively used in cooling applications and heating applications. Heat exchangers in buildings are typically components of space-conditioning systems, as well as of water-heating applications. Heat exchangers are also sometimes used in applications that require storage and release of energy at specific times. Phase change materials (PCMs) enhance these heat-exchange processes, given their ability to melt and solidify at a fixed range of temperatures, absorbing or releasing significant amounts of latent heat. Five different configurations of PCM–air heat exchangers for thermal control in buildings are analyzed in this work. The heat exchangers were fitted with PCM encapsulated in plastic and composite pouches of various shapes, and packaged in stackable panel layers. Three-dimensional computational fluid dynamics (CFD) modeling of coupled incompressible fluid and conjugate heat transfer were performed on the designs. The phase change process was numerically modelled using the apparent heat capacity method. Steady-state CFD simulations provided quantification of pressure drop as a function of air flow velocity. Transient simulation results describe the thermal evolution of PCM in the pouches, helping to determine the best performing configuration with respect to total thermal charging time.

10 SYNTHETIC FUELS↗

DOE OSTI2023

Airfoil Computational Fluid Dynamics - 9k shapes, 2 AoA's

This dataset contains aerodynamic quantities - including flow field values (momentum, energy, and vorticity) and summary values (coefficients of lift, drag, and momentum) - for 8,996 airfoil shapes, computed using the HAM2D CFD (computational fluid dynamics) model. The airfoil shapes were designed using the separable shape tensor parameterization that encodes two-dimensional shapes as elements of the Grassmann manifold. This data-driven approach learns two independent spaces of parameter from a collection of sample airfoils. The first captures large-scale, linear perturbations, and the second defines small-scale, higher-order perturbations. For this data, we used the G2Aero database of over 19,000 airfoil shapes to learn a parameter space that captured a wide array of shape characteristics. We fixed the linear deformations to be the mean over the database and sampled new shapes over a four-dimensional parameter space of higher-order perturbation. This sampling approaches allows for isolated analysis of non-linear airfoil shape deformations while holding other aspects (e.g., airfoil thickness) approximately constant. The aerodynamic quantities for the generated airfoil were obtained using the HAM2D code, which is a finite-volume Reynolds-averaged Navier-Stokes (RANS) flow solver. We employ a fifth-order WENO scheme for spatial reconstruction with Roe's flux difference scheme for inviscid flux and second-order central differencing for viscous flux. A preconditioned GMRES method is applied for implicit integration. The Spalart-Allmaras 1-eq turbulence model is used for the turbulence closure, and the Medida-Baeder 2-eq transition model is applied to account for the effects of laminar turbulent transition. The airfoil grid is generated with a total of 400 points on the airfoil surface, the initial wall-normal spacing of y+ = 1, and an outer boundary located at 300 chord lengths away from the wall. The CFD simulations are performed at a freestream Mach number of 0.1, Reynolds number of 9M, and at two angles of attack, 4 deg. and 12 deg. The simulations were performed using the Bridges-2 system at the Pittsburgh Supercomputing Center in February 2023 as part of the INTEGRATE project funded by the Advanced Research Projects Agency - Energy in the U.S. Department of Energy. The data was collected, reformatted, and preprocessed for this OEDI submission in July 2023 under the Foundational AI for Wind Energy project funded by the U.S. Department of Energy Wind Energy Technologies Office. This dataset is intended to serve as a benchmark against which new artificial intelligence (AI) or machine learning (ML) tools may be tested. Baseline AI/ML methods for analyzing this dataset have been implemented, and a link to their repository containing those models has been provided. The .h5 data file structure can be found in the GitHub Repository resource under explore_airfoil_9k_data.ipynb.

9k↗

DOE OSTI2022

Multiscale Experiments and Multiphysics Simulation of Multiphase Flow for Transportable Small Modular Reactors

A new type of safe, small, transportable nuclear reactor would address the intense and ever-growing global demand for energy produced via a resilient, carbon-free energy source. In this regard, transportable small modular reactors (SMRs) are being designed and developed for electricity generation within small/micro-grid/off-grid isolated systems, as well as for heat generation in industrial/residential applications. These reactors feature the capability to be fully factory fabricated and then directly transported to utilities’ sites as “plug-and-play” systems. Research and development (R&D) programs are underway at Idaho National Laboratory (INL) to successfully design, develop, and demonstrate such safe-by-design mobile reactor technologies, in collaboration with partner organizations. Multiscale experimental facilities and multiphysics simulation tools are required for reactor design verification and validation (V&V), and licensing. These advanced reactors are intended to feature passive safety systems such as passive containment cooling systems (PCCS), which consist of multiphase flows and multispecies distributions. This seminar talk will focus on designing and analyzing transportable SMR PCCS by using multiscale experiments and multiphysics computational fluid dynamics (CFD) simulations to support reactor licensing and safety. The corresponding research challenges are addressed via supportive verification and validation results generated by the models and simulation tools in combination with selective parametric and uncertainty analysis. This solution approach could blaze the trail for commercial adoption of such technologies. The facilities, simulation capabilities, and research opportunities available at INL in regard to such reactors and the integrated energy systems with which they go hand in hand are also discussed briefly, and may spark interest in deeper research as well as new collaborative projects.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

Expansion dynamics of femtosecond laser-induced plasmas: Influence of thermophysical plasma properties

This study investigates the expansion dynamics of femtosecond laser-induced plasmas, emphasizing the impact of plasma thermophysical properties and ambient gas composition. Through shadowgraphy experiments and multiphase computational fluid dynamics (CFD) simulations, the influence of parameters such as heat capacity, molecular weight, and thermal conductivity on plume morphology, shockwave evolution, and energy dissipation mechanisms is examined. A mixture multiphase model is implemented to capture the interaction between the plasma and the surrounding gas. Simulation results reveal that plasma expansion is strongly inertia-driven. Results show that differences in plasma properties and ambient conditions affect the shape and temperature distribution of the expanding plume. The early-stage dynamics are primarily dictated by pressure forces, whereas thermal and viscous effects play a growing role in the plume's behavior during later stages of expansion. The CFD findings show the necessity of accurate initial condition characterization, including crater geometry and plasma pressure and temperature, for reliable modeling of plasma evolution in laser ablation processes.

CFD modeling↗

DOE OSTI2024

LES and RANS Spray Combustion Analysis of OME 3-5 and n-Dodecane

Clean-burning oxygenated and synthetic fuels derived from renewable power, so-called e-fuels, are a promising pathway to decarbonize compression–ignition engines. Polyoxymethylene dimethyl ethers (PODEs or OMEs) are one candidate of such fuels with good prospects. Their lack of carbon-to-carbon bonds and high concentration of chemically bound oxygen effectively negate the emergence of polycyclic aromatic hydrocarbons (PAHs) and even their precursors like acetylene (C 2 H 2 ), enabling soot-free combustion without the soot-NO x trade-off common for diesel engines. The differences in the spray combustion process for OMEs and diesel-like reference fuels like n-dodecane and their potential implications on engine applications include discrepancies in the observed ignition delay, the stabilized flame lift-off location, and significant deviations in high-temperature flame morphology. For CFD simulations, the accurate modeling and prediction of these differences between OMEs and n-dodecane proved challenging. This study investigates the spray combustion process of an OME 3 − 5 mixture and n-dodecane with advanced optical diagnostics, Reynolds-Averaged Navier–Stokes (RANS), and Large-Eddy Simulations (LESs) within a constant-volume vessel. Cool-flame and high-temperature combustion were measured simultaneously via high-speed (50 kHz) imaging with formaldehyde (CH 2 O) planar laser-induced fluorescence (PLIF) representing the former and line-of-sight OH* chemiluminescence the latter. Both RANS and LES simulations accurately describe the cool-flame development process with the formation of CH 2 O. However, CH 2 O consumption and the onset of high-temperature reactions, signaled by the rise of OH* levels, show significant deviations between RANS, LES, and experiments as well as between n-dodecane and OME. A focus is set on the quality of the simulated results compared to the experimentally observed spatial distribution of OH*, especially in OME fuel-rich regions. The influence of the turbulence modeling is investigated for the two distinct ambient temperatures of 900 K and 1200 K within the Engine Combustion Network Spray A setup. The capabilities and limitations of the RANS simulations are demonstrated with the initial cool-flame propagation and periodic oscillations of CH 2 O formation/consumption during the quasi-steady combustion period captured by the LES.

CFD↗

DOE OSTI2024

Simulate Wind Loading on RUTE SunTracker: Cooperative Research and Development (Final Report)

RUTE produces and delivers efficient, sustainable structural foundation systems for the wind and solar industries, instrumental in the effort to lower the cost of clean electricity and reduce CO2. RUTE's SunTracker is a high-clearance agrivoltaic solar array. The system uses raised cables, providing support with less materials and cost. These cables can provide tracking for increased energy generation and greater revenue, allowing the land beneath to be used for other means simultaneously. RUTE provided data files that NREL will use to perform computational fluid dynamics (CFD) simulations to characterize and predict wind loading on the 6x6 RUTE SunTracker photovoltaic (PV) array. Varying both the panel orientations and wind speeds provides information on how the array can manage a variety of weather conditions. These results, in turn, inform RUTE's design and construction of these arrays.

14 SOLAR ENERGY↗

DOE OSTI2021

Arctic observations and numerical simulations of surface wind effects on Multi-Angle Snowflake Camera measurements

Abstract. Ground-based measurements of frozen precipitation are heavily influenced by interactions of surface winds with gauge-shield geometry. The Multi-Angle Snowflake Camera (MASC), which photographs hydrometeors in free-fall from three different angles while simultaneously measuring their fall speed, has been used in the field at multiple midlatitude and polar locations both with and without wind shielding. Here, we present an analysis of Arctic field observations – with and without a Belfort double Alter shield – and compare the results to computational fluid dynamics (CFD) simulations of the airflow and corresponding particle trajectories around the unshielded MASC. MASC-measured fall speeds compare well with Ka-band Atmospheric Radiation Measurement (ARM) Zenith Radar (KAZR) mean Doppler velocities only when winds are light (≤5ms-1) and the MASC is shielded. MASC-measured fall speeds that do not match KAZR-measured velocities tend to fall below a threshold value that increases approximately linearly with wind speed but is generally <0.5ms-1. For those events with wind speeds ≤1.5ms-1, hydrometeors fall with an orientation angle mode of 12∘ from the horizontal plane, and large, low-density aggregates are as much as 5 times more likely to be observed. Simulations in the absence of a wind shield show a separation of flow at the upstream side of the instrument, with an upward velocity component just above the aperture, which decreases the mean particle fall speed by 55 % (74 %) for a wind speed of 5 m s−1 (10 m s−1). We conclude that accurate MASC observations of the microphysical, orientation, and fall speed characteristics of snow particles require shielding by a double wind fence and restriction of analysis to events where winds are light (≤5ms-1). Hydrometeors do not generally fall in still air, so adjustments to these properties' distributions within natural turbulence remain to be determined.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Understanding flow dynamics in membrane distillation: Effects of reactor design on polarization

Optimization and design of full-scale membrane distillation (MD) systems usually require Sherwood and Nusselt correlations that are developed from lab-scale systems. However, entrance effects in lab-scale systems can significantly impact heat, mass and momentum transfer in the reactor, therefore affect the accuracy of the developed experimental Sherwood and Nusselt correlations. Here, Computational Fluid Dynamics (CFD) simulations using OpenFOAM are performed to understand the effects of right-angled bends and inlet design on flow dynamics, temperature and concentration polarization in MD systems. Simulation results show that the presence of right-angled bends and inlets with sudden expansions lead to the formation of Dean vortices. Dean vortices enhance perpendicular mixing in MD systems and reduce both temperature and concentration polarization. Temperature and concentration polarization coefficients in MD systems with right-angled bends and inlets with sudden expansions vary significantly for the same volumetric flow rate. Our studies show that lab-scale systems with the same volumetric flow rate but different designs lead to significantly different Nusselt and Sherwood correlations. Here, this study demonstrates the importance of CFD-informed design of lab-scale systems to minimize entrance effects and suppress Dean vortices for consistent model development and calibration across multiple scales.

42 ENGINEERING↗

DOE OSTI2024

Computational study on the impact of gasoline-ethanol blending on autoignition and soot/NO x emissions under low-load gasoline compression ignition conditions

Here, in the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine are performed to investigate the impact of gasoline-ethanol blending on autoignition, nitrogen oxide (NO x ), and soot emissions under low-load conditions. In order to represent the test gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF)+ethanol (ETPRF) surrogate (with 10% ethanol by volume; E10) is employed. A three-dimensional (3D) engine CFD model employing finite-rate chemistry with a skeletal kinetic mechanism (including NO x sub-mechanism), adaptive mesh refinement (AMR), and hybrid method of moments (HMOM) is adopted to capture the in-cylinder combustion phenomena and soot/NO x emissions. The engine CFD model is validated against experimental data for three gasoline-ethanol blends: E10, E30 and E100, with varying ethanol content by volume. Model validation is carried out for a broad range of start-of-injection (SOI) timings (−21, −27, −36, and −45 crank angle degrees (°CA) after top-dead-center (aTDC)) with respect to in-cylinder pressure, heat release rate, combustion phasing, NO x and soot emissions. For relatively later injection timings (−21 and −27 °CA aTDC), E30 yields higher amount of soot than E10; while the trend reverses for early injection cases (−36 and −45 °CA aTDC ). On the other hand, E100 yields the lowest amount of soot among all fuels irrespective of SOI timing. Further, E10 shows a non-monotonic trend in soot emissions with SOI timing: SOI-36>SOI-45>SOI-21>SOI-27, while soot emissions from E30 exhibit monotonic decrease with advancing SOI timing. NO x emissions from various fuels follow a trend of E10>E30>E100. On the other hand, NO x emissions increase as SOI timing is advanced for all fuels, with an anomaly for E10 and E100 where NO x decreases when SOI is advanced beyond −36 °CA aTDC. Detailed analysis of the numerical results is performed to investigate the soot/NO x emission trends and elucidate the impact of chemical composition and physical properties on autoignition and emissions characteristics.

Computational fluid dynamics↗

DOE OSTI2021

Simulation of Premixed and Partially Premixed Jet-in-Crossflow Flames at High Pressure

In this paper, we explore the operational map of a lean axial-staged combustor of premixed and partially premixed reacting jet-in-crossflow flames at high -pressure (5 atm). This study attempts to expand the data to relatively high pressure and could significantly aid scaling to real gas turbine engine conditions at 20–30 atm. High-speed camera, particle image velocimetry (PIV), CH* chemiluminescence, temperature, and pressure measurements were taken and processed to allow accurate reconstruction of six operating points relative to computational fluid dynamics (CFD) simulations under minimal adjustments. Variation of lean main stage (φ = 0.575 and 0.73) and rich jet (φ = 1.1, 4, and 8) equivalence ratio has been investigated for a four mm axial jet. The fully premixed flames were found to be controlled by the crossflow temperature before ignition and the crossflow oxygen content during combustion. Analysis of flame shape and position for the partially premixed operating points describes a lee stabilized as well as a more unsteady windward flame branch. Adjustment of added jet fuel and crossflow temperature along with its corresponding oxygen level is required to attain a compact flame body. Here, the risk of delaying combustion progress is significantly increased at a richer jet φ = 8 and an overshooting, spatially divided flame was attained with a main stage φ = 0.73. Control toward a compact flame body is critical to allow combustion at reasonable reaction rate.

03 NATURAL GAS↗

DOE OSTI2022

Effect of fuel composition and EGR on spark-ignited engine combustion with LPG fueling: Experimental and numerical investigation

This paper presents an experimental and numerical investigation of a spark-ignited (SI) cooperative fuel research (CFR) engine fueled with different liquefied petroleum gas (LPG) fuels and exhaust gas recirculation (EGR). Here, the effects of LPG fuel composition on engine combustion characteristics are initially evaluated at two different compression ratios (CR). Results show normal combustion at CR 7 and heavy knocking combustion at CR 10 for all the tested fuels, with a more substantial impact for the LPG fuel with high proportions of n-butane species. The Livengood-Wu (LW) integral method is then used to analyze the knock occurrence risk of individual fuel based on the reactivity of the tested fuels. The introduction of EGR then demonstrates the potential of knock intensity reduction below the borderline knock limit. A zonal-based kinetic interactions study is also performed to understand the knock mitigation effectiveness of EGR over the pressure–temperature domain relevant to SI engine operation. Finally, a multidimensional, computational fluid dynamics (CFD) simulation model is shown to predict the LPG combustion characteristics and presents the evolution of in-cylinder temperature and chemical species to demonstrate the development of end-gas autoignition events without and with EGR.

02 PETROLEUM↗

DOE OSTI2020

Real Fuel Modeling for Gasoline Compression Ignition Engine

Increasing regulatory demand for efficiency has led to development of novel combustion modes such as HCCI, GCI and RCCI for gasoline light duty engines. In order to realize HCCI as a compression ignition combustion mode system, in-cylinder compression temperatures must be elevated to reach the autoignition point of the premixed fuel/air mixture. This should be co-optimized with appropriate fuel formulations that can autoignite at such temperatures. CFD combustion modeling is used to model the auto ignition of gasoline fuel under compression ignition conditions. Using the fully detailed fuel mechanism consisting of thousands of components in the CFD simulations is computationally expensive. To overcome this challenge, the real fuel is represented by few major components of create a surrogate fuel mechanism. In this study, 9 variations of gasoline fuel sets were chosen as candidates to run in HCCI combustion mode. A study detailing the development of the gasoline real fuel model was performed and various surrogates for gasoline fuel were investigated. The gasoline real fuel model will be used in subsequent CFD modelling activities for the development of an advanced mixed mode combustion system as part of the Department of Energy funded project DE-EE0008478.

Gasoline Compression Ignition, real fuel modeling,↗

DOE OSTI2026

Integrated Neutronics Modeling for Inertial Fusion Energy Systems: Development and Application to LD-FIRST

Lawrence Livermore National Laboratory (LLNL) is proposing a new Laser Driven Fusion Integration Research and Science Test Facility (LD-FIRST) with the goal of providing an experimental testbed for future Inertial Fusion Energy (IFE) systems. However, IFE systems require detailed and accurate multiphysics modeling to quantify material damage, thermal loading, and tritium breeding within complex chamber environments. This article presents the first step in an integrated multiphysics framework that couples meshed CAD-based geometry within Monte Carlo neutronic simulations to enable high-fidelity analysis of IFE chamber concepts, with future coupling to external codes. The neutronics workflow utilizes OpenMC and its third-party capability to use CAD-based geometries through DAGMC and tally on unstructured meshes with Libmesh to evaluate neutron transport behavior, geometric fidelity, and material performance under reactor-relevant conditions. The use of tailored tallies on unstructured meshes in this framework allows direct transfer without interpolating to CFD simulation tools. Two IFE chambers were evaluated, both conceived by LLNL: HYLIFE-II and Laser IFE (LIFE). This work produced high-fidelity conformal surface and volumetric meshes of the HYLIFE-II and LIFE chambers with mapped spatial insight into material damage, thermal loading, and tritium breeding. The HYLIFE-II model was built utilizing available resources and used as a test case to verify that the neutronics framework can handle complex geometries. The LIFE chamber CAD was provided by LLNL and was the main focus of this work. This work analyzes multiple ternary alloy breeding materials for the LIFE chamber, across different 6 Li enrichments to produce data relevant to the LD-FIRST project. This work also investigates the level of model fidelity for the LIFE chamber, and results show that inclusion of detailed first wall and coolant structures increased the predicted tritium breeding ratio (TBR) by ~30%, highlighting the sensitivity of tritium breeding and the need for a high-fidelity simulation framework for IFE chambers. These developments provide a scalable toolset for the design and optimization of next-generation IFE chambers, forming a solid foundation for future coupled multiphysics analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Prediction of local concentration fields in porous media with chemical reaction using a multi scale convolutional neural network

The study of solute transport in porous media is of interest in many chemical engineering systems. Some example applications include packed bed catalytic reactors, filtration devices, and batteries. The pore scale modeling of these systems is time consuming and may require large computing resources, for this reason computational fluid dynamics (CFD) simulations are not practical if a large number of simulations is required, like in multiscale modeling, where a model at a large scale calls for pore scale simulations. It has been shown that neural networks can be trained with a dataset of flow simulations and then predict fields orders of magnitude faster, and with less computational resources, in new domains. However, it is crucial to provide the neural network with an effective description of the domain and the undergoing operating conditions to be able to train models that generalize accurately in unseen samples. Therefore, research is needed to employ neural networks in new complex systems. The appropriate training of a network for predicting coupled flow and solute transport processes is an outstanding problem due to the complex interplay between geometry and operating conditions. In this work, we train a multi scale convolutional neural network (MSNet) with a diverse dataset of simulations of transport and chemical reaction in porous media to predict the local concentration fields in images of porous media. Our dataset contains a wide diversity of sphere pack arrangements under different operating conditions (Péclet and Reynolds numbers). Further, we train a robust model by employing different input descriptors that represent the medium and the different operating conditions of each system. Our trained model is able to provide nearly instantaneous predictions, compared to around twenty hours of the CFD workflow, with less than 3.5% error on new geometries and transport conditions. Thus the model could be easily integrated in a multiscale workflow where fast response is needed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

An Investigation of the Effects of Volume Fraction on Drag Coefficient of Non-Spherical Particles Using PR-DNS

Prediction of the drag coefficient is required in gas-particle multiphase flow modeling and simulation. Experimental data and correlations on the fixed-bed system of spherical particles with high volume fractions for various possible arrangements are available in the literature. However, the effect of volume fraction on the drag coefficient of non-spherical particles is not well studied. In solving the momentum equation, the volume fraction plays a vital role in determining the flow resistances. In this paper, we study the impact of volume fraction in the range of 0.069 to 0.65 on the drag coefficient using the computational fluid dynamics (CFD) simulation of air for Reynold number in the range of 10 to 10000 using particle resolved direct numerical solution (PR-DNS). Regular non-spherical particles such as a cube, tetrahedron, and spheroids are used in this study since their single particle’s drag coefficient data are available in the literature for comparison. For this work, the simulations are carried out in the Ansys Fluent using polyhedral mesh, which consumes significantly less computational time and power. The study showed the sphericity and volume fraction have significant impact on the bed pressure drop and average drag coefficient of the particles in the bed especially in high Reynolds number regime. The bed of the spheroid experiences the lowest drag being the most streamlined particle, and the particles with the edges result in a large drag coefficient due to flow separation at the discontinuity. The vector plots verify this behavior where large wake regions are observed behind the tetrahedron particle.

Mahyawansi, Pratik↗

DOE OSTI2021

A two-equation soot-in-flamelet modeling approach applied under Spray A conditions

Soot production (including formation and oxidation) is studied in the transient, high-pressure and turbulent n-dodecane Spray A flames from the Engine Combustion Network (ECN) using computational fluid dynamics (CFD) simulations. A two-equation soot-in-flamelet modeling approach is applied within the framework of the Unsteady Flamelet Progress Variable (UFPV) model and results are validated against experimental data. Equations for soot mass fraction and soot number density derived in the mixture fraction space are solved in the context of detailed flamelet calculations. Source terms for the different steps in the soot chemistry are tabulated and incorporated in the flamelet manifold. For the reference condition, the modeling approach based on the tabulated flamelet manifold reduces the computational cost of a CFD calculation by approximately 40 times compared to a non-tabulated well-mixed (WM) modeling approach. The soot-in-flamelet approach is then extended to study the effect of ambient oxygen concentration, ambient mixture composition and ambient temperature on soot production. Results show that the modeling approach is able to capture the experimental trends for the soot volume fraction (SVF) with good quantitative agreement, especially in the soot ramp-up region.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗