Results for “CFD simulations” — Page 10

NASA NTRS1994

Computational Methods for HSCT-Inlet Controls/CFD Interdisciplinary Research

A program aimed at facilitating the use of computational fluid dynamics (CFD) simulations by the controls discipline is presented. The objective is to reduce the development time and cost for propulsion system controls by using CFD simulations to obtain high-fidelity system models for control design and as numerical test beds for control system testing and validation. An interdisciplinary team has been formed to develop analytical and computational tools in three discipline areas: controls, CFD, and computational technology. The controls effort has focused on specifying requirements for an interface between the controls specialist and CFD simulations and a new method for extracting linear, reduced-order control models from CFD simulations. Existing CFD codes are being modified to permit time accurate execution and provide realistic boundary conditions for controls studies. Parallel processing and distributed computing techniques, along with existing system integration software, are being used to reduce CFD execution times and to support the development of an integrated analysis/design system. This paper describes: the initial application for the technology being developed, the high speed civil transport (HSCT) inlet control problem; activities being pursued in each discipline area; and a prototype analysis/design system in place for interactive operation and visualization of a time-accurate HSCT-inlet simulation.

Cole, Gary L.↗

DOE OSTI2025

Dominant balance-based adaptive mesh refinement for incompressible fluid flows

This work introduces a novel adaptive mesh refinement (AMR) method that utilizes dominant balance analysis (DBA) for efficient and accurate grid adaptation in computational fluid dynamics (CFD) simulations. The proposed method leverages a Gaussian mixture model (GMM) to classify grid cells into active and passive regions based on the dominant physical interactions within the equation space. By modeling truncation error probabilistically from discretized terms, the method identifies regions of high interaction where numerical accuracy is most sensitive to resolution. Unlike traditional AMR strategies, this approach does not rely on heuristic-based sensors or user-defined thresholds, providing a fully automated and problem-independent framework for AMR. Applied to the incompressible Navier-Stokes equations for steady and unsteady flow past a cylinder, the DBA-based AMR method achieves comparable accuracy to high-resolution grids while reducing computational costs by up to 70 %. The validation highlights the method’s effectiveness in capturing complex flow features while minimizing grid cells, directing computational resources toward regions with the most critical dynamics. This modular and scalable strategy is adaptable to a wide range of applications, presenting a promising tool for efficient high-fidelity simulations in CFD and other multiphysics domains.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS2000

Construction and Utilization of a Beowulf Computing Cluster: A User's Perspective

Lockheed Martin Space Operations - Stennis Programs (LMSO) at the John C Stennis Space Center (NASA/SSC) has designed and built a Beowulf computer cluster which is owned by NASA/SSC and operated by LMSO. The design and construction of the cluster are detailed in this paper. The cluster is currently used for Computational Fluid Dynamics (CFD) simulations. The CFD codes in use and their applications are discussed. Examples of some of the work are also presented. Performance benchmark studies have been conducted for the CFD codes being run on the cluster. The results of two of the studies are presented and discussed. The cluster is not currently being utilized to its full potential; therefore, plans are underway to add more capabilities. These include the addition of structural, thermal, fluid, and acoustic Finite Element Analysis codes as well as real-time data acquisition and processing during test operations at NASA/SSC. These plans are discussed as well.

Woods, Judy L.↗

DOE OSTI2021

Application of an automated machine learning-genetic algorithm (AutoML-GA) coupled with computational fluid dynamics simulations for rapid engine design optimization

In recent years, the use of machine learning-based surrogate models for computational fluid dynamics (CFD) simulations has emerged as a promising technique for reducing the computational cost associated with engine design optimization. However, such methods still suffer from drawbacks. One main disadvantage is that the default machine learning (ML) hyperparameters are often severely suboptimal for a given problem. This has often been addressed by manually trying out different hyperparameter settings, but this solution is ineffective in case of a high-dimensional hyperparameter space. Besides this problem, the amount of data needed for training is also not known a priori. In response to these issues that need to be addressed, the present work describes and validates an automated active learning approach, AutoML-GA, for surrogate-based optimization of internal combustion engines. In this approach, a Bayesian optimization technique is used to find the best machine learning hyperparameters based on an initial dataset obtained from a small number of CFD simulations. Subsequently, a genetic algorithm is employed to locate the design optimum on the ML surrogate surface. In the vicinity of the design optimum, the solution is refined by repeatedly running CFD simulations at the projected optima and adding the newly obtained data to the training dataset. It is demonstrated that AutoML-GA leads to a better optimum with a lower number of CFD simulations, compared to the use of default hyperparameters. The proposed framework offers the advantage of being a more hands-off approach that can be readily utilized by researchers and engineers in industry who do not have extensive machine learning expertise.

Owoyele, Opeoluwa↗

DOE OSTI2020

An error-controlled adaptive time-stepping method for particle advancement in coupled CFD-DEM simulations

Coupled Computational-Fluid-Dynamics (CFD) and Discrete-Element-Method (DEM) models provide an accurate description of multiphase physical systems where a solid granular particle phase exists in an underlying gaseous continuous medium. The time integration of the granular phase in these simulations is typically handled using an explicit scheme with a constant time-step among all particles that is invariant in time to resolve inter-particle collisions. A locally third-order accurate adaptive time integration technique for particles that employs an embedded locally second-order scheme for error determination is presented in this work. The particle time-step size is dynamically adapted based on solution error, thus leading to significant savings in computational time. The efficacy of our scheme is quantified using four test cases of varying complexity (binary collision, homogeneous cooling system, fluidized bed and hopper discharge). The adaptive time-stepping method exhibits improved performance (~ 2–3 times in most of the cases studied) compared to three commonly used non-adaptive time-step methods (first-order Euler-explicit, second-order Adams-Bashforth and third-order Runge-Kutta schemes), while maintaining the same level of accuracy and parallel scalability.

42 ENGINEERING↗

NASA NTRS2014

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Gorazd Medic↗

NASA NTRS2014

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Gorazd Medic↗

NASA NTRS2017

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Centrifugal compressor↗

NASA NTRSDate not supplied

Wind-US Simulations of the NASA 1507 Inlet Test Case

Steady-state, Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) simulations were performed of the NASA 1507 Inlet Test Case from the 6th AIAA Propulsion Aerodynamics Workshop (PAW) held in January 2023 using the Wind-US CFD solver. The simulations were performed with bleed regions modeled as surface patches and the Slater bleed boundary condition models were applied within those regions. Both the constant-plenum-pressure and the fixed-plenum-exit bleed models where applied. The vortex generators were modeled using the Bender-Anderson-Yagle (BAY) vortex generator model. The CFD simulations were performed for inlet engine-face flow ratios varying from supercritical to subcritical inlet operation until inlet unstart. The results of the CFD simulations were compared to wind-tunnel data which included boundary layer profiles, axial static pressure distributions, bleed rates, total pressure recovery performance curves, and engine-face total pressure rake profiles. The CFD simulations were able to match most of the boundary layer rake data near the geometric throat, but the boundary layers on the centerbody were thinner than indicated by the wind-tunnel data. For the supercritical CFD simulations, the engine-face flow ratio was at least 2% to 2.5% lower than indicated by the wind-tunnel data, but still consistent with the level of supercritical bleed. The engine-face flow rates of the wind-tunnel tests had an uncertainty of ±2% which could explain the differences. The supercritical engine-face flow rates of the wind-tunnel data indicated a 5% supercritical bleed rate rather than the reported 7.18% bleed rate. The CFD simulations were able to calculate the maximum total pressure recovery of pt2/pt = 0.907 as observed for the wind-tunnel data. The CFD simulations with the constant-pressure bleed model were able to obtain a much lower engine-face total pressure ratio than indicated by both the wind-tunnel data and the CFD simulations using a fixed-plenum-exit bleed model. The CFD simulations indicated a sharp static pressure rise for the terminal shock rather than a more gradual rise indicated by the wind-tunnel data. The CFD simulations were not able to accurately compute the total pressure variation across the engine-face total pressure rake.

Supersonics↗

NASA NTRS2020

Sketch-to-Solution: A Case Study in RCS Aerodynamic Interaction

Thanks to recent advances in the fields of anisotropic grid adaptation, error estimation, and geometry modeling, a sketch-to-solution work flow is now possible for viscous computational fluid dynamic (CFD) simulations. With this workflow, a CFD application engineer provides geometry, boundary conditions, and flow parameters; and the sketch-to-solution process yields a CFD simulation through automatic, error-based, grid adaptation. To explore the benefits of this nascent capability, a conventional manual grid generation work flow is compared to this new automatic grid generation work flow for a given engineering question: What are the aerodynamic interactions caused by the reaction control system (RCS) on an entry vehicle? This case study indicates that while the automatic grid generation sketch-to- solution process is not yet mature, it is preferred over a manual grid generation work flow because it greatly reduces manual labor, eliminates many opportunities for human error, and provides grid sensitivity information.

Bill Kleb↗

DOE OSTI2022

Latent Space Simulation for Carbon Capture Design Optimization

The CO2 capture efficiency in solvent-based carbon capture systems (CCSs) critically depends on the gas-solvent interfacial area (IA), making maximization of IA a foundational challenge in CCS design. While the IA associated with a particular CCS design can be estimated via a computational fluid dynamics (CFD) simulation, using CFD to derive the IAs associated with numerous CCS designs is prohibitively costly. However, previous works such as Deep Fluids (Kim et al., 2019) show that large simulation speed-ups and low error are achievable by replacing CFD simulators with neural-network (NN) surrogates that mimic the CFD simulation process. This raises the possibility for a fast, accurate replacement for a CFD simulator, and thus computationally feasible IA-based CCS-design optimization. As such, here, we explore whether an existing NN-surrogate approach (and variants we develop) can successfully be applied to our complex carbon-capture CFD simulations, with the ultimate goal of obtaining a fast and accurate simulator for our CCS-design application. Our experiments build on the Deep Fluids approach and find that resulting surrogates can produce large speed ups (4000x) while maintaining IA relative errors as low as 4% on unseen CCS configurations (interpolating between configurations seen during training). Thus, despite less faithfulness to the underlying physics of the problem, NN surrogates may be a promising tool for our CCS design optimization problem. Notably, though, the Deep Fluids approach has limitations for our application (such as model non-transferability to CCS-packing changes), which we discuss. We conclude with potential directions for future work that may, like innovations we introduced here (e.g., transformer-based dynamics prediction), improve performance on our complicated dataset of CCS CFD simulations.

AI Surrogate Simulation, Carbon Capture, design op↗

DOE OSTI2023

A reduced-order model of concentration polarization in reverse osmosis systems with feed spacers

Feed spacers in reverse osmosis systems generate complex fluid flows that limit computational fluid dynamics (CFD) simulations to small length and time scales. That limits our ability to simulate mineral scaling and other membrane fouling phenomena, which occur over longer length and time scales. Thus motivated, we develop a reduced model that replaces the CFD simulation of the velocity field with an analytical model that mimics spacers. This focuses the remaining numerical effort on simulating the advection–diffusion equation governing solute transport. We motivate and validate the model with CFD simulations and bench-scale experiments of spacer filaments in three different arrangements, including cases of unsteady vortex shedding. We show that the model produces a roughly 10,000-fold speedup compared to CFD, and accurately reproduces CFD predictions of not only the average and maximum concentrations, but also the local concentration distribution along the membrane. Here, we also demonstrate the model for simulating a feed channel with a length-to-height ratio of 200. The model provides a simple testbed for exploratory studies of multispecies transport, precipitation, and membrane fouling phenomena for which simulating spacers is often prohibitive.

Computational fluid dynamics↗

NASA NTRS2001

Development of Advanced Casing Treatments for Flow Control

Under the Base R&T and Ultra Efficient Engine Technology programs, the NASA-Goddard Space Flight Center Compressor Branch is investigating flow control strategies required to increase the loading and efficiency of core compressors while maintaining current levels of operability. Flow-control strategies being studied include advanced casing treatments, wall jet injection, and blade-tip injection for compressor stability enhancement, directed jets for surface boundary layer control, and vortex-generating devices. The use of computational fluid dynamics (CFD) simulations to assess the effectiveness of flow-control devices and to guide their design is a key element in this research. CFD simulations serve to screen potential flow-control concepts at a lower cost than executing physical experiments in turbomachinery facilities. CFD simulations also provide guidance in designing physical experiments for those flow control concepts, which appear promising.

Keith, Theo G., Jr.↗

NASA NTRS2004

Automated Extraction of Flow Features

Computational Fluid Dynamics (CFD) simulations are routinely performed as part of the design process of most fluid handling devices. In order to efficiently and effectively use the results of a CFD simulation, visualization tools are often used. These tools are used in all stages of the CFD simulation including pre-processing, interim-processing, and post-processing, to interpret the results. Each of these stages requires visualization tools that allow one to examine the geometry of the device, as well as the partial or final results of the simulation. An engineer will typically generate a series of contour and vector plots to better understand the physics of how the fluid is interacting with the physical device. Of particular interest are detecting features such as shocks, recirculation zones, and vortices (which will highlight areas of stress and loss). As the demand for CFD analyses continues to increase the need for automated feature extraction capabilities has become vital. In the past, feature extraction and identification were interesting concepts, but not required in understanding the physics of a steady flow field. This is because the results of the more traditional tools like; iso-surface, cuts and streamlines, were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of a great deal of interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one "snapshot" of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for (co-processing environments). Methods must be developed to abstract the feature of interest and display it in a manner that physically makes sense.

Dorney, Suzanne↗

NASA NTRS2005

Automated Extraction of Flow Features

Computational Fluid Dynamics (CFD) simulations are routinely performed as part of the design process of most fluid handling devices. In order to efficiently and effectively use the results of a CFD simulation, visualization tools are often used. These tools are used in all stages of the CFD simulation including pre-processing, interim-processing, and post-processing, to interpret the results. Each of these stages requires visualization tools that allow one to examine the geometry of the device, as well as the partial or final results of the simulation. An engineer will typically generate a series of contour and vector plots to better understand the physics of how the fluid is interacting with the physical device. Of particular interest are detecting features such as shocks, re-circulation zones, and vortices (which will highlight areas of stress and loss). As the demand for CFD analyses continues to increase the need for automated feature extraction capabilities has become vital. In the past, feature extraction and identification were interesting concepts, but not required in understanding the physics of a steady flow field. This is because the results of the more traditional tools like; isc-surface, cuts and streamlines, were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of a great deal of interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one "snapshot" of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for co-processing environments). Methods must be developed to abstract the feature of interest and display it in a manner that physically makes sense.

Dorney, Suzanne↗

DOE OSTI2024

ECAR-7932 Rev 0 Large Eddy Simulation of MARVEL Reactor Core Subchannel to Evaluate Model Uncertainty of Reynolds-Averaged Navier-Stokes Equation Based Computational Fluid Dynamics Analysis

In the previous work (ECAR-7210), the peak cladding temperature of the MARVEL microreactor has been evaluated by steady-state Reynolds-Averaged Navier-Stokes (RANS) based computational fluid dynamics (CFD) simulations. Although numerical uncertainties of RANS-based CFD simulations has been assessed in ECAR-7210, the model uncertainty of RANS turbulence models must be investigated to resolve the issues related to inaccurate prediction of turbulent heat flux and flow pulsation in a tight lattice rod bundle using the steady-state RANS simulations. Consequently, this ECAR conducted a high-fidelity CFD analysis utilizing Large Eddy Simulation (LES) to generate reference data and investigated the model uncertainty of RANS-based CFD simulations.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

NASA NTRS2016

NASA ERA Integrated CFD for Wind Tunnel Testing of Hybrid Wing-Body Configuration

The NASA Environmentally Responsible Aviation (ERA) Project explored enabling technologies to reduce impact of aviation on the environment. One project research challenge area was the study of advanced airframe and engine integration concepts to reduce community noise and fuel burn. To address this challenge, complex wind tunnel experiments at both the NASA Langley Research Center's (LaRC) 14'x22' and the Ames Research Center's 40'x80' low-speed wind tunnel facilities were conducted on a BOEING Hybrid Wing Body (HWB) configuration. These wind tunnel tests entailed various entries to evaluate the propulsion-airframe interference effects, including aerodynamic performance and aeroacoustics. In order to assist these tests in producing high quality data with minimal hardware interference, extensive Computational Fluid Dynamic (CFD) simulations were performed for everything from sting design and placement for both the wing body and powered ejector nacelle systems to the placement of aeroacoustic arrays to minimize its impact on vehicle aerodynamics. This paper presents a high-level summary of the CFD simulations that NASA performed in support of the model integration hardware design as well as the development of some CFD simulation guidelines based on post-test aerodynamic data. In addition, the paper includes details on how multiple CFD codes (OVERFLOW, STAR-CCM+, USM3D, and FUN3D) were efficiently used to provide timely insight into the wind tunnel experimental setup and execution.

Computational Fluid Dynamics↗

DOE OSTI2021

An out-of-distribution-aware autoencoder model for reduced chemical kinetics

While detailed chemical kinetic models have been successful in representing rates of chemical reactions in continuum scale computational fluid dynamics (CFD) simulations, applying the models in simulations for engineering device conditions is computationally prohibitive. To reduce the cost, data-driven methods, e.g., autoencoders, have been used to construct reduced chemical kinetic models for CFD simulations. Despite their success, data-driven methods rely heavily on training data sets and can be unreliable when used in out-of-distribution (OOD) regions (i.e., when extrapolating outside of the training set). In this paper, we present an enhanced autoencoder model for combustion chemical kinetics with uncertainty quantification to enable the detection of model usage in OOD regions, and thereby creating an OOD-aware autoencoder model that contributes to more robust CFD simulations of reacting flows.Here, we first demonstrate the effectiveness of the method in OOD detection in two well-known datasets, MNIST and Fashion-MNIST, in comparison with the deep ensemble method, and then present the OOD-aware autoencoder for reduced chemistry model in syngas combustion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗