Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BaSiC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Perception of linear horizontal self-motion induced by peripheral vision /linearvection/ - Basic characteristics and visual-vestibular interactions

The basic characteristics of the sensation of linear horizontal motion have been studied. Objective linear motion was induced by means of a moving cart. Visually induced linear motion perception (linearvection) was obtained by projection of moving images at the periphery of the visual field. Image velocity and luminance thresholds for the appearance of linearvection have been measured and are in the range of those for image motion detection (without sensation of self motion) by the visual system. Latencies of onset are around 1 sec and short term adaptation has been shown. The dynamic range of the visual analyzer as judged by frequency analysis is lower than the vestibular analyzer. Conflicting situations in which visual cues contradict vestibular and other proprioceptive cues show, in the case of linearvection a dominance of vision which supports the idea of an essential although not independent role of vision in self motion perception.

Berthoz, A.↗
NASA NTRS1976

Basic limits on protocol information in data communications networks

The paper considers basic limitations on the amount of protocol information that must be transmitted in a data communication network to keep track of source and receiver addresses and of the starting and stopping of messages. Assuming Poisson message arrivals between each communicating source-receiver pair, a lower bound is found on the required protocol information for message. This lower bound is the sum of two terms, one for the message-length information, which depends only on the distribution of message lengths, and the other for the message-start information, which depends only on the product of the source-receiver pair arrival rate and the expected delay for transmitting the message. Two strategies are developed which, in the limit of large numbers of sources and receivers, almost meet the lower bound on protocol information.

Gallager, R. G.↗
NASA NTRS1976

Long-duration exposure facility - A new capability for space testing and basic research

The reusable Long-Duration Exposure Facility (LDEF), which can accommodate experiments requiring large exposure surface areas, large volumes and/or massive hardware, offers to researchers a new inexpensive opportunity to conduct extended technology and basic research testing in the space environment. Many researchers with interest varying from medical research to astrophysics research will have their experiments performed in the 80 large experiment trays on the first LDEF flight. This paper describes the LDEF and a number of experiments now being developed for the first mission. In particular, this paper illustrates the value of the LDEF features which allow the return of the experiment hardware and repeated flights.

Dibattista, J. D.↗
NASA NTRS1977

Design and fabrication of a basic mass analyzer and vacuum system

A two-inch hyperbolic rod quadrupole mass analyzer with a mass range of 400 to 200 amu and a sensitivity exceeding 100 packs per billion has been developed and tested. This analyzer is the basic hardware portion of a microprocessor-controlled quadrupole mass spectrometer for a Gas Analysis and Detection System (GADS). The development and testing of the hyperbolic-rod quadrupole mass spectrometer and associated hardware are described in detail.

Judson, C. M.↗
NASA NTRS1976

Introduction to basic solar cell measurements

The basic approaches to solar cell performance and diagnostic measurements are described. The light sources, equipment for I-V curve measurement, and the test conditions and procedures for performance measurement are detailed. Solar cell diagnostic tools discussed include analysis of I-V curves, series resistance and reverse saturation current determination, spectral response/quantum yield measurement, and diffusion length/lifetime determination.

Brandhorst, H. W., Jr.↗
NASA NTRS1976

On the magnetic mirroring as the basic cause of parallel electric fields

Among the different proposed mechanisms for generating parallel electric fields, magnetic mirroring of charged particles seems to be the most plausible. In the present paper, it is suggested that magnetic mirroring is the basic cause of parallel electric fields in the magnetosphere and that the magnetic mirroring effect may be able to form the basis of an auroral theory that can remove a major portion of the ambiguity of observations. In the model proposed, the parallel electric field is due to a magnetic confinement of a negatively charged hot collision-free plasma. A transfer of electron gyroenergy into wave energy tends to weaken this confinement; if this energy transfer becomes too strong, the parallel potential gradient will break down. Hence, from this model, in contrast to certain other models of parallel electric fields, only a small fraction of the total auroral particle energy may be expected to be transformed into electromagnetic wave energy during the acceleration process.

Lennartsson, W.↗
NASA NTRS1976

Basic aspects of superalloy design for crack growth resistance

It is pointed out that the major difficulty concerning an understanding of the flaw growth resistance properties of superalloys is related to the lack of basic theories. An attempt is made to develop these theories, taking into account their use for the identification of tentative alloy design guidelines for flaw growth resistance. A brief review of the fatigue crack growth literature is provided. Attention is given to continuous fatigue crack growth theory, threshold fatigue crack growth, planar slip superalloy fatigue crack growth, and aspects of creep crack growth resistance.

Tien, J. K.↗
NASA NTRS1977

Basic coaxial mass driver construction and testing

A basic coaxial mass driver has been constructed by a group of students to verify performance predictions in the acceleration range envisaged for the first lunar device. The bucket is guided by four copper tubes which also supply direct current excitation for its single aluminum coil, and is accelerated by twenty coaxial coils along a 2 m track, followed by a deceleration section. The coils are individually energized by electrolytic photoflash capacitors triggered by solid state switches on the basis of bucket position.

Fine, K.↗
NASA NTRS1976

Basic mechanisms governing solar-cell efficiency

The efficiency of a solar cell depends on the material parameters appearing in the set of differential equations that describe the transport, recombination, and generation of electrons and holes. This paper describes the many basic mechanisms occurring in semiconductors that can control these material parameters.

Lindholm, F. A.↗
NASA NTRS1977

Design considerations in mechanical face seals for improved performance. 1: Basic configurations

Basic assembly configurations of the mechanical face seal are described and some advantages associated with each are listed. The various forms of seal components are illustrated, and functions pointed out. The technique of seal pressure balancing and its application are described; and the concept of the PV factor, its different forms and limitations are discussed. Brief attention is given to seal lubrication since it is covered in detail in a companion paper. Finally, the operating conditions for various applications of low pressure seals (aircraft transmissions) are listed, and the seal failure mode of a particular application is discussed.

Ludwig, L. P.↗
NASA NTRS1972

Wind-tunnel investigation of basic aerodynamic characteristics of a supercritical-wing research airplane configuration

Transonic pressure tunnel and transonic tunnel tests were performed to determine the aerodynamic characteristics of a 0.087 scale model of a supercritical wing research airplane configuration at Mach numbers from 0.25 to 1.30. The investigation included tests to determine the basic longitudinal aerodynamic characteristics, the lateral-directional aerodynamic characteristics for sideslip angles of 0 deg and + or - 2.5 deg, and the effects of Reynolds number and aeroelasticity.

Dennis W Bartlett↗
NASA NTRS1977

Basic linear algebra subprograms for FORTRAN usage

A package of 38 low level subprograms for many of the basic operations of numerical linear algebra is presented. The package is intended to be used with FORTRAN. The operations in the package are dot products, elementary vector operations, Givens transformations, vector copy and swap, vector norms, vector scaling, and the indices of components of largest magnitude. The subprograms and a test driver are available in portable FORTRAN. Versions of the subprograms are also provided in assembly language for the IBM 360/67, the CDC 6600 and CDC 7600, and the Univac 1108.

Lawson, C. L.↗
NASA NTRS1977

Design considerations in mechanical face seals for improved performance. I - Basic configurations

Basic assembly configurations of the mechanical face seal are described and some advantages associated with each are listed. The various forms of seal components (the primary seal, secondary seal, etc.) are illustrated, and functions pointed out. The technique of seal pressure balancing and its application is described; and the concept of the PV factor, its different forms and limitations are discussed. Brief attention is given to seal lubrication since it is covered in detail in a companion paper. Finally, the operating conditions for various applications of low pressure seals (aircraft transmissions) are listed, and the seal failure mode of a particular application is discussed.

Ludwig, L. P.↗
NASA NTRS1978

Effectiveness of basic display augmentation in vehicular control by visual field cues

The paper investigates the effectiveness of different basic display augmentation concepts - fixed reticle, velocity vector, and predicted future vehicle path - for RPVs controlled by a vehicle-mounted TV camera. The task is lateral manual control of a low flying RPV along a straight reference line in the presence of random side gusts. The man-machine system and the visual interface are modeled as a linear time-invariant system. Minimization of a quadratic performance criterion is assumed to underlie the control strategy of a well-trained human operator. The solution for the optimal feedback matrix enables the explicit computation of the variances of lateral deviation and directional error of the vehicle and of the control force that are used as performance measures.

Grunwald, A. J.↗
NASA NTRS1978

Basic avionics module design for general aviation aircraft

The design of an advanced digital avionics system (basic avionics module) for general aviation aircraft operated with a single pilot under IFR conditions is described. The microprocessor based system provided all avionic functions, including flight management, navigation, and lateral flight control. The mode selection was interactive with the pilot. The system used a navigation map data base to provide operation in the current and planned air traffic control environment. The system design included software design listings for some of the required modules. The distributed microcomputer uses the IEEE 488 bus for interconnecting the microcomputer and sensors.

Smyth, R. K.↗
NASA NTRS1978

JSC interactive basic accounting system

Design concepts for an interactive basic accounting system (IBAS) are considered in terms of selecting the design option which provides the best response at the lowest cost. Modeling the IBAS workload and applying this workload to a U1108 EXEC 8 based system using both a simulation model and the real system is discussed.

Spitzer, J. F.↗
NASA NTRS1980

Development of basic theories and techniques for determining stresses in rotating turbine or compressor blades

A method for measuring in-plane displacement of a rotating structure by using two laser speckle photographs is described. From the displacement measurements one can calculate strains and stresses due to a centrifugal load. This technique involves making separate speckle photographs of a test model. One photograph is made with the model loaded (model is rotating); the second photograph is made with no load on the model (model is stationary). A sandwich is constructed from the two speckle photographs and data are recovered in a manner similar to that used with conventional speckle photography. The basic theory, experimental procedures of this method, and data analysis of a simple rotating specimen are described. In addition the measurement of in-plane surface displacement components of a deformed solid, and the application of the coupled laser speckle interferometry and boundary-integral solution technique to two dimensional elasticity problems are addressed.

Chien, C. H.↗