Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aerosol Observing System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Overview of the MOSAiC expedition—Atmosphere

With the Arctic rapidly changing, the needs to observe, understand, and model the changes are essential. To support these needs, an annual cycle of observations of atmospheric properties, processes, and interactions were made while drifting with the sea ice across the central Arctic during the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition from October 2019 to September 2020. An international team designed and implemented the comprehensive program to document and characterize all aspects of the Arctic atmospheric system in unprecedented detail, using a variety of approaches, and across multiple scales. These measurements were coordinated with other observational teams to explore cross-cutting and coupled interactions with the Arctic Ocean, sea ice, and ecosystem through a variety of physical and biogeochemical processes. This overview outlines the breadth and complexity of the atmospheric research program, which was organized into 4 subgroups: atmospheric state, clouds and precipitation, gases and aerosols, and energy budgets. Atmospheric variability over the annual cycle revealed important influences from a persistent large-scale winter circulation pattern, leading to some storms with pressure and winds that were outside the interquartile range of past conditions suggested by long-term reanalysis. Similarly, the MOSAiC location was warmer and wetter in summer than the reanalysis climatology, in part due to its close proximity to the sea ice edge. The comprehensiveness of the observational program for characterizing and analyzing atmospheric phenomena is demonstrated via a winter case study examining air mass transitions and a summer case study examining vertical atmospheric evolution. Overall, the MOSAiC atmospheric program successfully met its objectives and was the most comprehensive atmospheric measurement program to date conducted over the Arctic sea ice. The obtained data will support a broad range of coupled-system scientific research and provide an important foundation for advancing multiscale modeling capabilities in the Arctic.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Indications of a Decrease in the Depth of Deep Convective Cores with Increasing Aerosol Concentration during the CACTI Campaign

Abstract An aerosol indirect effect on deep convective cores (DCCs), by which increasing aerosol concentration increases cloud-top height via enhanced latent heating and updraft velocity, has been proposed in many studies. However, the magnitude of this effect remains uncertain due to aerosol measurement limitations, modulation of the effect by meteorological conditions, and difficulties untangling meteorological and aerosol effects on DCCs. The Cloud, Aerosol, and Complex Terrain Interactions (CACTI) campaign in 2018–19 produced concentrated aerosol and cloud observations in a location with frequent DCCs, providing an opportunity to examine the proposed aerosol indirect effect on DCC depth in a rigorous and robust manner. For periods throughout the campaign with well-mixed boundary layers, we analyze relationships that exist between aerosol variables (condensation nuclei concentration > 10 nm, 0.4% cloud condensation nuclei concentration, 55–1000-nm aerosol concentration, and aerosol optical depth) and meteorological variables [level of neutral buoyancy (LNB), convective available potential energy, midlevel relative humidity, and deep-layer vertical wind shear] with the maximum radar-echo-top height and cloud-top temperature (CTT) of DCCs. Meteorological variables such as LNB and deep-layer shear are strongly correlated with DCC depth. LNB is also highly correlated with three of the aerosol variables. After accounting for meteorological correlations, increasing values of the aerosol variables [with the exception of one formulation of aerosol optical depth (AOD)] are generally correlated at a statistically significant level with a warmer CTT of DCCs. Therefore, for the study region and period considered, increasing aerosol concentration is mostly associated with a decrease in DCC depth.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Modeling the Impact of the Organic Aerosol Phase State on Multiphase OH Reactive Uptake Kinetics and the Resultant Heterogeneous Oxidation Timescale of Organic Aerosol in the Amazon Rainforest

Accurate predictions of chemical lifetime, i.e., oxidation timescale and change in the mass of organic aerosols (OAs) in atmospheric models, are critical to quantify the impacts of OA on aerosol–cloud interactions, radiative forcing, and air quality. The heterogeneous oxidation of OA by hydroxyl (OH) radicals is a key process governing OA mass changes during their oxidation. Recently, laboratory observations of the OH uptake coefficient (γ OH ) and heterogeneous reaction rate (k het,OH ) for different OA systems with varying phase states have been combined to develop a new parameterization of γ OH and k het,OH as a function of the OA phase state, i.e., viscosity (η OA ). Here, in this work, we use a recently published viscosity prediction framework to analyze the new γ OH and k het,OH parameterization with a box model. Subsequently, we implement this box model to predict γ OH and k het,OH over the Amazon rainforest in the dry-to-wet transition season with both significant biomass burning and biogenic influences. Relevant parameters within our box model are specified based on detailed regional model simulations over the Amazon using the Weather Research and Forecasting model coupled with Chemistry (WRF-Chem). η OA is predicted as a function of species volatility, OA composition (including water uptake) along with ambient relative humidity (RH), and temperature. Based on ambient conditions simulated by WRF-Chem over the entire atmospheric column, we use the box model to predict the upper bounds of the heterogeneous oxidation timescale of OA. Based on previous laboratory measurements, we assume that this heterogeneous OH oxidation causes fragmentation (carbon loss) of OA, followed by the evaporation of the fragmented molecules that results in the exponential decay of OA. We predict that the oxidation timescale of OA is ~1 month near the Earth’s surface in the pristine Amazonian background because of low OH concentrations. But OA is oxidized more rapidly within urban and wildfire plumes near the Earth’s surface with an order of magnitude higher OH concentrations compared to the pristine background, causing the simulated oxidation timescale of OA to be much shorter, ~3–4 days. At 3–5 km altitudes where biomass burning OA is predicted to be semisolid, the heterogeneous oxidation timescale is estimated as ~6 days to 3 weeks and decreases with increasing OH concentrations within plumes. We show that the simulated mass loss of OA is strongly size-dependent, where smaller particles oxidize more rapidly compared to larger particles due to their greater per-particle surface area-to-volume ratio. Increasing urbanization and deforestation in the Amazon in the future might increase OH concentrations in the background Amazon, causing faster oxidation of OA. At higher altitudes above liquid clouds, especially in the upper troposphere where temperatures approach ~250 K, future measurements are needed to reduce the uncertainties related to the mass loss of OA at colder temperatures and low relative humidity conditions due to its heterogeneous OH oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Observations of supermicron-sized aerosols originating from biomass burning in southern Central Africa

During the 3 years of the ObseRvations of Aerosols above CLouds and their intEractionS (ORACLES) campaign, the NASA Orion P-3 was equipped with a 2D stereo (2D-S) probe that imaged particles with maximum dimension (D) ranging from 10 < D < 1280 µm. The 2D-S recorded supermicron-sized aerosol particles (SAPs) outside of clouds within biomass burning plumes during flights over the southeastern Atlantic off Africa's coast. Numerous SAPs with 10 < D < 1520 µm were observed in 2017 and 2018 at altitudes between 1230 and 4000 m, 1000 km from the coastline, mostly between 7–11° S. No SAPs were observed in 2016 as flights were conducted further south and further from the coastline. Number concentrations of refractory black carbon (rBC) measured by a single particle soot photometer ranged from 200 to 1200 cm –3 when SAPs were observed. Transmission electron microscopy images of submicron particulates, collected on Holey carbon grid filters, revealed particles with potassium salts, black carbon (BC), and organics. Energy-dispersive X-ray spectroscopy spectra also detected potassium, a tracer for biomass burning. These measurements provided evidence that the submicron particles originated from biomass burning. NOAA Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) 3 d back trajectories show a source in northern Angola for times when large SAPs were observed. Fire Information for Resource Management System (FIRMS) Moderate Resolution Imaging Spectroradiometer (MODIS) 6 active fire maps showed extensive biomass burning at these locations. Given the back trajectories, the high number concentrations of rBC, and the presence of elemental tracers indicative of biomass burning, it is hypothesized that the SAPs imaged by the 2D-S are examples of BC aerosol, ash, or unburned plant material.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Analysis of secondary organic aerosol simulation bias in the Community Earth System Model (CESM2.1)

Organic aerosol (OA) has been considered as one of the most important uncertainties in climate modeling due to the complexity in presenting its chemical production and depletion mechanisms. To better understand the capability of climate models and probe into the associated uncertainties in simulating OA, we evaluate the Community Earth System Model version 2.1 (CESM2.1) configured with the Community Atmosphere Model version 6 (CAM6) with comprehensive tropospheric and stratospheric chemistry representation (CAM6-Chem) through a long-term simulation (1988–2019) with observations collected from multiple datasets in the United States. We find that CESM generally reproduces the interannual variation and seasonal cycle of OA mass concentration at surface layer with a correlation of 0.40 compared to ground observations and systematically overestimates (69%) in summer and underestimates (-19%) in winter. Through a series of sensitivity simulations, we reveal that modeling bias is primarily related to the dominant fraction of monoterpene-formed secondary organic aerosol (SOA), and a strong positive correlation of 0.67 is found between monoterpene emission and modeling bias in the eastern US during summer. In terms of vertical profile, the model prominently underestimates OA and monoterpene concentrations by 37%–99% and 82%–99%, respectively, in the upper air (>500 m) as validated against aircraft observations. Our study suggests that the current volatility basis set (VBS) scheme applied in CESM might be parameterized with monoterpene SOA yields that are too high, which subsequently results in strong SOA production near the emission source area. We also find that the model has difficulty in reproducing the decreasing trend of surface OA in the southeastern US probably because of employing pure gas VBS to represent isoprene SOA which is in reality mainly formed through multiphase chemistry; thus, the influence of aerosol acidity and sulfate particle change on isoprene SOA formation has not been fully considered in the model. This study reveals the urgent need to improve the SOA modeling in climate models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Impacts of sea ice leads on sea salt aerosols and atmospheric chemistry in the Arctic

Abstract. The processes contributing to Arctic cold-season (November–April) sea salt aerosols (SSAs) remain uncertain. Observations from coastal Alaska suggest that emissions from open leads in sea ice, which are not included in climate models, may play a dominant role. Their Arctic-wide significance has not yet been quantified. Here, we create an emission parameterization of SSAs from leads by combining satellite data of lead area (the Advanced Microwave Scanning Radiometer–Earth Observation System (AMSR-E) product) and a chemical transport model (GEOS-Chem) to quantify pan-Arctic SSA emissions from leads during the cold season from 2002 to 2008 and to predict their impacts on atmospheric chemistry, evaluating the results of our simulated SSAs against in situ observations. The AMSR-E product detects large leads with certainty (> 3 km in size), and, hence, our study is limited to quantifying emissions from large leads. Lead emissions vary seasonally and interannually. Simulated total monthly SSA emissions increase by 1.1 %–1.8 % (≥60° N latitude) and 5.6 %–7.5 % (≥75° N) for the 2002–2008 cold seasons. SSA concentrations primarily increase at the location of leads, where standard model concentrations are low. GEOS-Chem overestimates SSA concentrations at Arctic sites compared to ground observations, even when lead emissions are not included, suggesting underestimation of SSA sinks and/or uncertainties in SSA emissions from blowing snow and the open ocean. Multi-year monthly mean surface bromine atom (Br) concentrations increase by 2.8 %–8.8 % due to SSAs from leads for the 2002–2008 cold seasons. Changes in ozone concentrations are negligible. While leads contribute < 10 % to Arctic-wide SSA emissions in the years 2002–2008, these emissions occur in regions of low background aerosol concentrations. Leads may increase in frequency under future climate change, which could increase SSA emissions from leads.

Emme, Erin J. (ORCID:0000000268406352)↗
DOE OSTI2020

Understanding Biomass Burning Aerosol via Integrated Analyses of Aerosol Mass Spectrometry Data from DOE Campaigns and ACRF Long Term Measurements

Biomass burning (BB) is one of the largest sources of aerosol particles in the atmosphere and a significant source of trace gases important to atmospheric chemistry. Organic aerosols from biomass burning sources (BBOA) are an important but poorly characterized component of the earth’s climate system. BBOA composition and life cycle processes are associated with enormous complexities and contribute significantly to model uncertainties. Hence it is important to improve the ability to simulate the concentration and properties (chemical, optical, and hygroscopic) of BBOA and the atmospheric aging processes that affect these properties. Here, we propose to analyze ambient data collected from the DOE Biomass Burning Observation Project (BBOP) field campaign and from a long term measurement site of the Atmospheric Radiation Measurement (ARM) program – the Southern Great Plains (SGP), where transported BB plumes and elevated BBOA episodes were frequently observed. This project is aimed at 1) gaining detailed, quantitative understanding of the chemical and physical properties of BBOA and their chemical changes during atmospheric aging via advanced analysis of aerosol measurement data acquired at the summit of Mt. Bachelor (MBO) during the BBOP campaign and through integration with concurrent measurements of trace gases, particle properties, and meteorological conditions performed at MBO and from the G-1 aircraft; 2) gaining better understanding of BBOA properties and its roles in radiative forcing via analysis of routine data from the ARM long-term measurement sites; and 3) integrating the results from 1) and 2) into a global database of aerosol mass spectrometry and collaborate with modelers on evaluating and improving numerical model performance as part of the ASR program.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Subtask 2.6 – Optimization of Aerosol Mitigation Technology for Postcombustion CO 2 Capture

Growing concerns over the impact of CO 2 emissions from combustion sources on global climate change have prompted numerous research and development projects aimed at developing cost-effective technologies for CO 2 capture. One family of technologies being demonstrated at pilot and full scale globally is postcombustion CO 2 capture (PCCC) systems that employ amine-based solvents. The captured CO 2 can be compressed and permanently stored underground or used for enhanced oil recovery (EOR). The proximity of North Dakota’s lignite-fired fleet of power plants to potential CO 2 storage options creates a unique atmosphere for PCCC within the state. However, the aerosols present in lignite flue gas present a challenge for large-scale PCCC at North Dakota power plants. Aerosols can negatively impact the long-term performance of amine-based solvents for CO 2 capture. Amine-based solvents are volatile, and aerosols provide nucleation sites where amine vapors can condense. Because aerosols cannot be easily captured at the column outlet using conventional technologies, the amine-laden aerosols escape the system and lead to accelerated solvent losses. Moreover, aerosol components can chemically react with amines to form degradation products that can permanently deactivate the amine, cause fouling, and lead to hazardous emissions. Many of the elements that have been shown to catalyze solvent degradation are present in lignite coals and can exacerbate solvent replacement economics. Understanding this issue is critical to the implementation of solvent-based CO 2 capture systems as applied to lignite-fired generation systems. The Energy & Environmental Research Center (EERC) designed and carried out this project to optimize aerosol mitigation technology for PCCC at a lignite-fired power plant. To meet the goal of this project, the following objectives were identified: Determine the effectiveness of a wet electrostatic precipitator (WESP) on collection of aerosols at a low-rank coal-fired power station. Determine the impact of aerosols on the efficiency and degradation products of amine-based carbon capture systems fired with low-rank fuels. Work was conducted at Minnkota Power Cooperative’s (MPC’s) Milton R. Young (MRY) Station Unit 2 using a slipstream of flue gas from the outlet of the plant’s flue gas desulfurization (FGD) unit. To gather initial data for sizing and specifying a WESP for this system, a temporary pilot-scale WESP was rented and installed on-site. Several different conditions were tested to examine the impact of flow rate, voltage, and current on WESP performance. The WESP was effective at removing large particulate (>200 nm) but caused an increase in fine particulate (<75 nm). Fine particulate material at the inlet and outlet of the WESP was collected, analyzed, and showed that crystalline sulfates carried over from the plant’s FGD unit were being converted to fine aerosols and SO 2 was being converted to SO 3 through the WESP. Additionally, the high moisture content of the flue gas stream at this sample location also contributed to an overall increase in aerosol mass under some of the test conditions. Using the results from the rented WESP, the project team installed a smaller-scale WESP upstream of the EERC’s slipstream CO 2 capture system. Flue gas was routed through a pilot-scale FGD unit to remove SO 2 to very low levels (~1 ppm) and then through a direct contact cooler (DCC) to further cool the gas and to remove moisture. The gas exiting the DCC was then routed through the new WESP before passing to the CO 2 absorber columns. Fluor’s amine-based solvent was used to scrub CO 2 from the slipstream through a set of two absorber columns. The rich solvent was regenerated in a stripper column by heating to drive off captured CO 2 . The system operated using a catch-and-release method where the CO 2 was separated to provide data on the process, but the captured CO 2 was released back into the host site stack. Aerosols and sulfur species were measured at multiple locations throughout the pilot-scale system. The inlet FGD and DCC removed much of the particulate matter and gaseous sulfur upstream of the WESP. With this configuration, the WESP achieved >95% particulate capture. The new WESP did not show any of the increases in SO 3 or other aerosol species that had been consistently observed with the larger-scale WESP installed immediately downstream of the plant’s full-scale FGD unit. Particulate samples captured and analyzed from the WESP inlet did not show any presence of crystalline sulfate materials, indicating that the pilot-scale FGD and DCC were efficient at reducing carryover from the plant’s full-scale FGD unit. A set of parametric tests were conducted on the new WESP to assess the impacts of flow rate, voltage, number of online WESP fields, and gas-phase sulfur content on aerosol and sulfur transformations. The results showed that the WESP performed similarly well at all sets of conditions. Sulfur and particulate matter exiting the WESP were further reduced through the absorber column as the amine-based solvent captured some of the residual contaminants. Solvent analysis showed that these species were slowly concentrating in the solvent over the duration of the test. When the WESP was taken offline and the sulfur slip through the FGD allowed to rise, the sulfate content in the solvent rose sharply, showing that the extra FGD and WESP were effective at reducing sulfate and cation uptake. This would be expected to extend amine-based solvent life by slowing the formation of heat-stable salts and other degradation products. This subtask was cofunded through the EERC–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission and MPC.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Detection of Aerosols at Microbar Pressures in an Exoplanet Atmosphere

The formation of hazes at microbar pressures has been explored by theoretical models of exoplanet atmospheres to explain Rayleigh scattering and/or featureless transmission spectra; however observational evidence of aerosols in the low-pressure formation environments has proved elusive. Here, we show direct evidence of aerosols existing at ~1 microbar pressures in the atmosphere of the warm sub-Saturn WASP-69b using observations taken with the Space Telescope Imaging Spectrograph and Wide Field Camera 3 instruments on the Hubble Space Telescope. The transmission spectrum shows a wavelength-dependent slope induced by aerosol scattering that covers 11 scale heights of spectral modulation. Drawing on the extensive studies of haze in our solar system, we model the transmission spectrum based on a scaled version of Jupiter’s haze-density profile to show that the WASP-69b transmission spectrum can be produced by scattering from an approximately constant density of particles extending throughout the atmospheric column from 40 millibar to microbar pressures. These results are consistent with theoretical expectations based on microphysics of the aerosol particles that have suggested haze can exist at microbar pressures in exoplanet atmospheres.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Utilizing a Storm-Generating Hotspot to Study Convective Cloud Transitions: The CACTI Experiment

The Cloud, Aerosol, and Complex Terrain Interactions (CACTI) field campaign was designed to improve understanding of orographic cloud life cycles in relation to surrounding atmospheric thermodynamic, flow, and aerosol conditions. The deployment to the Sierras de Córdoba range in north-central Argentina was chosen because of very frequent cumulus congestus, deep convection initiation, and mesoscale convective organization uniquely observable from a fixed site. The C-band Scanning Atmospheric Radiation Measurement (ARM) Precipitation Radar was deployed for the first time with over 50 ARM Mobile Facility atmospheric state, surface, aerosol, radiation, cloud, and precipitation instruments between October 2018 and April 2019. An intensive observing period (IOP) coincident with the RELAMPAGO field campaign was held between 1 November and 15 December during which 22 flights were performed by the ARM Gulfstream-1 aircraft. A multitude of atmospheric processes and cloud conditions were observed over the 7-month campaign, including numerous orographic cumulus and stratocumulus events; new particle formation and growth producing high aerosol concentrations; drizzle formation in fog and shallow liquid clouds; very low aerosol conditions following wet deposition in heavy rainfall; initiation of ice in congestus clouds across a range of temperatures; extreme deep convection reaching 21-km altitudes; and organization of intense, hail-containing supercells and mesoscale convective systems. These comprehensive datasets include many of the first ever collected in this region and provide new opportunities to study orographic cloud evolution and interactions with meteorological conditions, aerosols, surface conditions, and radiation in mountainous terrain.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Ship-based Observations and Climate Model Simulations of Cloud Phase over the Southern Ocean

The Southern Ocean (SO) clouds exert a significant influence on the Earth’s radiation budget. Here we analyzed ship-based remote sensing observations of SO clouds over a five-month long DOE ARM Measurements of Aerosols, Radiation and Clouds over the Southern Oceans (MARCUS) field campaign to better understand cloud phase variability. We developed a method to classify eight categories of hydrometeors (ice, liquid, mixed phase, rain, drizzle, snow, aerosols, and clear sky) based on measurements of lidar, radar and radiosondes. Cloud thermodynamic phases (liquid, ice and mixed phase) at coarser scales were further derived to compare with the DOE Energy Exascale Earth System Model version 1 (E3SMv1) simulation and the Earth Model Column Collaboratory (EMC 2 ) instrument simulator. For a scale-aware comparison with climate model simulations, we found that spatially averaging the raw remote sensing data (e.g., backscatter, reflectivity) results in increased cloud cover and cloud liquid, whereas, directly averaging cloud phase from higher to lower resolution maintains clear air regions and is thus recommended for in-cloud frequency comparisons. For cloud thermodynamic phases in stratiform clouds, the E3SM underestimates cloud ice and overestimates cloud liquid at temperatures between -40 and 0°C. When latitudes increase, both observations and simulations show a transition of dominant phase from liquid to ice for cloud tops as well as for the entire cloud columns, but the model underestimation of ice phase is more severe at higher latitudes. Such model bias is unlikely caused by spatial scale differences or lack of heterogeneity in cloud vertical structure in the simulation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Evaluation of E3SM Simulated Aerosols and Aerosol‐Cloud Interactions Across GCM and Convection‐Permitting Scales

This paper introduces an Earth system modeling testbed for predicting aerosols and aerosol‐cloud interactions (ACIs) at convection‐permitting scales. Using the Energy Exascale Earth System Model (E3SM) version 2 with a four‐mode Modal Aerosol Module, we conduct simulations at 3.25 km resolution on a regionally refined mesh (RRM) across four regions with distinct aerosol and cloud regimes. Results are compared with the standard 100 km E3SM configuration and evaluated against satellite, aircraft, and ground‐based observations. We find that increasing model resolution improves heavy precipitation simulation but amplifies positive bias in light drizzle at coarse resolution. These resolution‐induced changes affect cloud and aerosol properties to varying degrees across regions. Generally, cloud cover and liquid water path (LWP) show better agreement with satellite retrievals at 3.25 km, though surface‐based comparisons suggest otherwise. Aerosol composition remains poorly represented at both resolutions. The RRM increases Aitken mode aerosol number concentrations via enhanced new particle formation. However, accumulation mode aerosols are decreased at higher resolution as aerosol removals become more efficient. This partially contributes to fewer cloud condensation nuclei (CCN) and lower cloud droplet number concentrations (N d ), which produces larger model biases in some scenarios. These findings suggest that solely increasing horizontal resolution to kilometer scales is insufficient to broadly improve aerosol and cloud predictions without concurrent advancements in physical and chemical process representations. Nonetheless, the RRM moderately improves key ACI relationships such as CCN‐N d correlation, reflecting enhanced aerosol activation representation. The LWP‐N d relationship is also better captured by RRM, suggesting a better characterization of LWP adjustment.

Huang, Meng [Pacific Northwest National Laboratory↗
DOE OSTI2024

Opinion: The importance of historical and paleoclimate aerosol radiative effects

Abstract. Estimating past aerosol radiative effects and their uncertainties is an important topic in climate science. Aerosol radiative effects propagate into large uncertainties in estimates of how present and future climate evolves with changing greenhouse gas emissions. A deeper understanding of how aerosols affected the atmospheric energy budget under past climates is hindered in part by a lack of relevant paleo-observations and in part because less attention has been paid to the problem. Because of the lack of information we do not seek here to determine the change in the radiative forcing due to aerosol changes but rather to estimate the uncertainties in those changes. Here we argue that current uncertainties from emission uncertainties (90 % confidence interval range spanning 2.8 W m−2) are just as large as model spread uncertainties (2.8 W m−2) in calculating preindustrial to present-day aerosol radiative effects. There are no estimates of radiative forcing for important aerosols such as wildfire and dust aerosols in most paleoclimate time periods. However, qualitative analysis of paleoclimate proxies suggests that changes in aerosols between different past climates are similar in magnitude to changes in aerosols between the preindustrial and present day; plus, there is the added uncertainty from the variability in aerosols and fires in the preindustrial. From the limited literature we crudely estimate a paleoclimate aerosol uncertainty for the Last Glacial Maximum relative to preindustrial of 4.8 W m−2, and we estimate the uncertainty in the aerosol feedback in the natural Earth system over the paleoclimate (Last Glacial Maximum to preindustrial) to be about 3.2 W m−2 K−1. In order to more accurately assess the uncertainty in historical aerosol radiative effects, we propose a new model intercomparison project, which would include multiple plausible emission scenarios tested across a range of state-of-the-art climate models over the historical period. These emission scenarios would then be compared to the available independent aerosol observations to constrain which are most probable. In addition, future efforts should work to characterize and constrain paleo-aerosol forcings and uncertainties. Careful propagation of aerosol uncertainties in the literature is required to ensure an accurate quantification of uncertainties in projections of future climate changes.

Environmental Sciences & Ecology↗
DOE OSTI2023

Aerosol Hygroscopic Growth, Mixing State, and Cloud Condensation Nuclei Activity during TRACER (Field Campaign Report)

Convective clouds play a critical role in the Earth’s climate system. Recent research has shown that a realistic representation of convective processes is critical to constraining climate sensitivity in global climate models. Theoretical and modeling studies showed that aerosols could have strong dynamic feedback to convection in warm and humid environments through enhancing ice-related processes and condensational growth. A few observation-based studies also suggested the influence of aerosols on convective cloud and precipitation properties. However, robust observational quantification of an aerosol effect on convective clouds isolated from other factors remains elusive. Understanding the impact of aerosol on convective clouds requires knowledge of the cloud condensation nuclei (CCN) spectrum, which represents the number of particles that uptake water and form cloud droplets as a function of supersaturation. The water uptake by aerosol is also of critical importance for the direct interaction of aerosol with radiation (i.e., aerosol direct effect) due to light scattering and absorption by aerosol. While both droplet activation under supersaturated conditions (i.e., relative humidity RH > 100%) and the hygroscopic growth under sub-saturated conditions (i.e., RH < 100%) are strongly influenced by particle hygroscopicity, the thermodynamic regimes and measurement methods are quite different. Aerosol particles, especially organic particles, can exhibit higher hygroscopicity for droplet activation than that for hygroscopic growth. In the subsaturated regime, the hygroscopicity of organic particles can also vary strongly with RH. However, global climate models usually treat organic species in aerosols with a constant hygroscopicity, potentially introducing substantial uncertainties in the quantification of aerosol radiative effects.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

ARM TBS and TigerShark deployment data in 2021

In 2021, observational data collected using ARM platforms, including seven TigerShark UAS flights and 133 tethered balloon system (TBS) flights, were archived by the ARM Data Center and made publicly available to the user community.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Physicochemical and Molecular Insights into the Boundary Layer and Free Troposphere Aerosol Interactions over the Southern Great Plains

Ambient aerosols’ vertical profiles are critical for evaluating the role of aerosols in atmospheric chemistry and radiative transfer, but limited data on these profiles hinders our ability to fully assess their impact on the Earth's radiative balance. Here, in this study, we investigated the size-, time-, and altitude resolved composition of individual particles and bulk molecular composition of particle samples collected by an uncrewed aerial system–ArcticShark over the Southern Great Plains. Single particle microanalysis shows that, the free tropospheric (FT) samples are dominated (56-66%) by carbonaceous sulfate particles, while boundary layer (BL) samples are dominated (57-74%) by carbonaceous particles. Back trajectory simulations suggest that FT particles are likely influenced by long-range transport and have undergone aqueous-phase processing. Conversely, in-situ size distribution data shows evidence of particle growth in the upper BL and just below the FT. This observation may indicate vertical transport of particles from an elevated aerosol layer in the FT, possibly linked to a new particle formation event. This observation is further supported by high resolution molecular composition data, which reveals particle volatility increasing with increasing size, which aligns with the growth event. This study aids in fundamental understanding of the compositional and molecular specificity of vertically resolved organic aerosols to provide insights into particle size evolution for future atmospheric models.

ArcticShark↗
DOE OSTI2025

A Comparative Study of Cloud Properties Between Northern and Southern High Latitudes Based on ARM Observations and EAMv2 Simulations

Earth's high-latitude regions show a considerable amount of cloud coverage, which significantly affects global radiation budgets. Here, in this study, we examine ground- and ship-based remote sensing observations from two Atmospheric Radiation Measurement (ARM) field campaigns conducted in the high-latitude regions of Northern and Southern Hemispheres (NH and SH). A comparison of macrophysical properties for low, mid-level, high, and deep clouds shows that the cloud top heights and thickness values are higher in the Arctic for each cloud type compared with the Southern Ocean and Antarctic regions, possibly due to higher sea surface temperatures in the north Atlantic. The Arctic also shows lower ice phase occurrence frequencies compared with the SH high latitudes for low clouds. For high, mid-level and deep clouds, the cloud phase distributions as a function of temperature show small geographical variabilities. The observations are then compared with the Department of Energy (DOE) Energy Exascale Earth System Model (E3SM) to evaluate the representations of these cloud properties. Here, the results show that the model captures cloud base and top heights well and reproduces the differences in cloud macrophysical properties between the two hemispheres. But the model underestimates ice phase frequencies for all cloud types. Such model cloud phase bias is strongly correlated with positive relative humidity biases and negative aerosol number concentration biases, indicating an important role of relative humidity and aerosols in modulating cloud phase partitioning in the model.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Understanding effects of printhead geometry in aerosol jet printing

Aerosol jet printing offers a versatile, high-resolution digital patterning capability broadly relevant to flexible and printed electronic systems. Despite its promise and numerous demonstrations, the theoretical principles driving process outputs have not been thoroughly explored. In this study, a custom-built, modular printing system is developed to provide a head-to-head comparison of two print nozzle geometries to better understand the technology. Print resolution data from a range of process parameters are analyzed using a support vector machine framework. The linear deposition rate is identified as a key variable, which can confound careful studies of printing performance. Taking this into account, a clear difference is observed between the printheads, corresponding to a difference in resolution of 57% ± 11% under typical conditions. Models to understand differences in aerodynamic and mass transport effects identify enhanced drying within the NanoJet printhead as a likely cause of this difference. Overall, this study provides improved understanding of the aerosol jet printing process, including valuable insight to inform process optimization, robust data analysis, ink formulation, and printer geometric design.

42 ENGINEERING↗