Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additive Manufacture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Tensile properties, strain rate sensitivity, and activation volume of additively manufactured 316L stainless steels [Tensile properties of 316L stainless steels made by laser powder-bed-fusion additive manufacturing]

The tensile properties of additively manufactured (AM) metals and alloys are among the most important variables that impact the potential applications of these materials. Here we examine and report on the tensile properties of AM 316L stainless steels fabricated by the laser powder-bed-fusion (L-PBF) technique, via twelve sets of optimized laser processing parameters that produce materials with density >98.8 ± 0.10%. A heterogeneous microstructure is observed in all L-PBF samples, including microscopic features such as dislocations, cellular walls, elemental segregations, local misorientations, impurities, precipitates, and a large fraction of low-angle grain boundaries (2-10°, ~40–60%). The derived average grain size defined by high-angle grain boundaries (>10°) is ~30–50 μm. Tensile testing reveals a yield strength ranging from 552 to 635 MPa and a tensile-elongation-to-failure (TEF) of 0.09–0.42 for directly-printed samples, whereas these values are 592–690 MPa and 0.29–0.50 for samples machined from the as-built rectangular thin plates. In all samples, we observe a variation of tensile yield strength within ~15% but not the TEF, suggesting marginal microstructural changes despite a wide range of laser processing parameters. The large scatter of TEF in directly-printed samples originates from the sensitivity of thin gauge geometry (~2 mm 2 cross-section area) to the built-in flaws. We measured a substantially higher strain rate sensitivity (m~0.02–0.03) of L-PBF 316L compared to the coarse-grained counterparts (~0.006), together with a small activation volume of ~20–30b3 (where b is the Burgers vector of 316L). In conclusion, these deformation kinetics parameters suggest that the tensile plasticity of L-PBF 316L is controlled by a much finer microstructural length scale than the measured grain size, consistent with the high strength and juxtaposed nano- to macro-structures seen in these materials. Strategies to optimize the tensile properties of AM materials are discussed.

36 MATERIALS SCIENCE↗

ODI notebook additive_manufacturing_video_2022

Additive Manufacturing, video dataset Two-photon lithography (TPL) is a widely used 3D nanoprinting technique that uses laser light to create objects. Challenges to large-scale adoption of this additive manufacturing method include identifying light dosage parameters and monitoring during fabrication. A research team from LLNL, Iowa State University, and Georgia Tech is applying machine learning models to tackle these challenges-i.e., accelerate the process of identifying optimal light dosage parameters and automate the detection of part quality. Funded by LLNL's Laboratory Directed Research and Development Program, the project team has curated a video dataset of TPL processes for parameters such as light dosages, photo-curable resins, and structures. Both raw and labeled versions of the datasets are available on the links in the Open Data Initiative page. The code uses the labeled dataset. Notebook compiled by Nisha Mulakken (mulakken1@llnl.gov) for LLNL Open Data Initiative, Summer 2022. Original code provided by research team. Publications: X.Y. Lee, S.K. Saha, S. Sarkar, B. Giera. "Automated detection of part quality during two-photon lithography via deep learning." Additive Manufacturing 36, December 2020: doi.org/10.1016/j.addma.2020.101444 X.Y. Lee, S.K. Saha, S. Sarkar, B. Giera. "wo Photon lithography additive manufacturing: Video dataset of parameter sweep of light dosages, photo-curable resins, and structures." Data in Brief 32, October 2020. doi.org/10.1016/j.dib.2020.106119.

Mulakken, NishaJ↗

Fabrication of highly dense isotropic Nd-Fe-B nylon bonded magnets via extrusion-based additive manufacturing [Fabrication of highly dense isotropic Nd-Fe-B bonded magnets via extrusion-based additive manufacturing]

Magnetically isotropic bonded magnets with a high loading fraction of 70 vol.% Nd-Fe-B are fabricated via an extrusion-based additive manufacturing, or 3D printing system that enables rapid production of large parts. The density of the printed magnet is ~5.2 g/cm 3 . The room temperature magnetic properties are: intrinsic coercivity H ci = 8.9 kOe (708.2 kA/m), remanence B r = 5.8 kG (0.58 T), and energy product (BH)max = 7.3 MGOe (58.1 kJ/m 3 ). The as-printed magnets are then coated with two types of polymers, both of which improve the thermal stability as revealed by flux aging loss measurements. Tensile tests performed at 25 °C and 100 °C show that the ultimate tensile stress (UTS) increases with increasing loading fraction of the magnet powder, and decreases with increasing temperature. AC magnetic susceptibility and resistivity measurements show that the 3D printed Nd-Fe-B bonded magnets exhibit extremely low eddy current loss and high resistivity. Lastly, we demonstrate the performance of the 3D printed magnets in a DC motor configuration via back electromotive force measurements.

36 MATERIALS SCIENCE↗

Additively manufactured tantalum microstructures

Additively manufacturing tantalum is a challenging process in which obstacles are stemming from the high melting temperature and susceptibility to oxidation of tantalum. In this paper, several combinations of deposition parameters were considered in an effort to obtain fully dense additively manufactured tantalum produced on an EOSINT M280 DMLS system. Deposition parameters significantly affect the resulting microstructure of additively manufactured tantalum, altering grain morphology, grain size, crystallographic preferred orientation, and deposition porosity. Due to the nature of the laser sintering process applied, which implies large directional temperature gradients, the resulting microstructures were strongly columnar along the building direction. Microstructural differences for different deposition conditions manifested themselves in both grain morphology and preferred crystal orientations in the columnar grains. Deposition speed and laser power were important parameters to consider for obtaining porosity-free material. Finally, stripe width had the most significant effect on grain growth.

36 MATERIALS SCIENCE↗

AFRL Additive Manufacturing Modeling Series: Challenge 4, In Situ Mechanical Test of an IN625 Sample with Concurrent High-Energy Diffraction Microscopy Characterization

In this work, we describe 3D characterization of an additively manufactured Inconel 625 nickel-base superalloy specimen conducted during a uniaxial tension test using a suite of nondestructive x-ray techniques. High-energy diffraction microscopy in both near- and far-field modalities are employed in situ to track evolution of the material orientation and stress–strain fields at six points during the mechanical test, and these data streams are registered with micro-computed tomography reconstructions which probe the material density. This data volume was matched to a multi-modal serial sectioning characterization of the specimen taken after loading, described in this article’s companion. Twenty-eight grains which were monitored throughout the experiment were selected to form the basis for AFRL AM Modeling Series Challenge 4, Microscale Structure-to-Properties.

36 MATERIALS SCIENCE↗

Microstructure Alignment Effects from Engineered Cooling during Additive Manufacturing of Alnico Magnets from Prealloyed Powder

Alnico is a rare-earth free; permanent magnet (PM) which maintains its saturation magnetization while at temperatures up to 550°C but lacks the coercivity and energy product needed for a wide range of demanding applications. With an optimal set of processing and manufacturing techniques, Alnico could replace Dy-free Nd-Fe-B magnets in certain applications if the microstructure is textured in a $\langle$001$\rangle$ direction. Additive manufacturing (AM) of near-net-shape magnets may provide such texture. To investigate the possibility, directed-energy deposition (DED) in conjunction with an actively cooled substrate was used to build samples with a compositionally modified, gas-atomized, Alnico 8 alloy. The resulting samples were solutionized and quenched, followed by magnetic annealing and a heat treatment. Magnetic properties and microstructures are compared to previous work.

36 MATERIALS SCIENCE↗

CHARACTERIZATION ON ANISOTROPIC THERMAL CONDUCTIVITY FOR BIG AREA ADDITIVE MANUFACTURING WITH POLYMERS

Additive manufacturing with polymers has been used mainly for prototyping. A recent development of Big Area Additive Manufacturing (BAAM) at Oak Ridge National Laboratory has opened its applications in the mold and die industry. A numerical simulation and prediction for a mold heating performance requires accurate anisotropic thermal properties of the printed material, which are challenging to obtain, and often requires the use of multiple techniques. The transient plane source (TPS) technique has been widely used due to its ability to measure the thermal properties of an extensive range of materials (solids, liquids, powder). Despite the capability to characterize thermal conductivity k of isotropic and anisotropic materials, the measurements of latter materials are limited to the cases, where the samples have the same thermal conductivity k along x- and y-axis that form the radial plane. In this work, the method for a characterization of k in all three dimensions is developed, and the application of TPS is extended to the determination of thermal properties along the x-, y-, and z-axis individually. The materials are represented by additively manufactured polymers including polylactic acid (PLA) and styrene maleic anhydride (SMA). The developed method consists of (1) a determination of the heat capacity of the polymers by means of TPS in combination with the developed in this work data analysis procedure, (2) a machining three types of cylindrical samples from the same material, with the height corresponding either to x-, y-, or z-direction of printing, and (3) a determination of axial thermal conductivity employing anisotropic model and using previously determined heat capacity

Trofimov, Artem↗

Creep suppression and fatigue in bio-based composites manufactured via conventional and large format additive manufacturing processes

The emergence of novel extrusion-based additive manufacturing (AM) processes has prompted the development of new thermoplastic composite feedstocks, and broadening sustainability initiatives have driven the development of bio-based and recyclable material for AM feedstocks. Poly(lactic acid) (PLA) with wood flour (WF) is one composite system that has been demonstrated in numerous AM applications, as well as traditional processing methods (i.e., compression and injection molding); however, there has been a need to understand how the variation in processing methodology impacts the material performance of these bio-based feedstocks from a fundamental perspective, with particular emphasis on creep for an extended application use-life. Herein, PLA/WF is explored as a feedstock material for large format additive manufacturing (LFAM) and the performance of additively manufactured materials is compared to those produced via more traditional processing methods. It is also demonstrated that the addition of WF decreases the material’s coefficient of thermal expansion (CTE) while increasing its Young’s modulus, susceptibility to water uptake, and creep fatigue resistance. Essentially, the addition of 20 wt% WF results in a 92 % decrease in rubbery regime CTE while simultaneously resulting in a 14 % increase in modulus, 190 % increase in water uptake, and a 31 % decrease in residual strain after cyclic creep tests. The processing method was also found to play a large role in the final part performance, with the printed material increasing the crystallinity by 183 % and 214 % compared to its compression and injection molded counterparts. Furthermore, the porosity of printed samples increased by two orders of magnitude compared to samples prepared via traditional processing methods.

36 MATERIALS SCIENCE↗

Grinding of additively manufactured silicon carbide surfaces for optical applications

Many of the properties of Silicon carbide (SiC) are advantageous for optical applications, such as telescope mirrors and industrial laser systems. However, the base shapes of complex components are costly and difficult to manufacture. Leveraging additive manufacturing, near net complex components are readily processed. In this work, we investigate the post processing of additively manufactured SiC (AM SiC) compared to chemical vapor deposited (CVD) SiC. The specific grinding energy for the AM SiC was lower than CVD, however the trends were the same. A specular finish was observed on both materials but the AM SiC finish was limited due to residual porosity.

36 MATERIALS SCIENCE↗

A review of materials used in tomographic volumetric additive manufacturing

Abstract Volumetric additive manufacturing is a novel fabrication method allowing rapid, freeform, layer-less 3D printing. Analogous to computer tomography (CT), the method projects dynamic light patterns into a rotating vat of photosensitive resin. These light patterns build up a three-dimensional energy dose within the photosensitive resin, solidifying the volume of the desired object within seconds. Departing from established sequential fabrication methods like stereolithography or digital light printing, volumetric additive manufacturing offers new opportunities for the materials that can be used for printing. These include viscous acrylates and elastomers, epoxies (and orthogonal epoxy-acrylate formulations with spatially controlled stiffness) formulations, tunable stiffness thiol-enes and shape memory foams, polymer derived ceramics, silica-nanocomposite based glass, and gelatin-based hydrogels for cell-laden biofabrication. Here we review these materials, highlight the challenges to adapt them to volumetric additive manufacturing, and discuss the perspectives they present. Graphical abstract

36 MATERIALS SCIENCE↗

DETERMINATION OF THE SOLID-STATE RESISTANCE-WELDABILITY OF ADDITIVELY MANUFACTURED 304L STAINLESS STEEL

Additive manufacturing of pressure-containing boundaries is of interest to numerous industries, so a project was initiated to develop several different methods to join and weld additively manufactured materials. The approach investigated in this study was a low energy, solid state spot weld. This general approach has been routinely used for conventionally prepared tubing and is now being expanded to additively manufactured components. Additively manufactured 304L stainless steel sheets, semi-tubes, and tubes were resistance spot welded and compared to comparable welds in conventionally manufactured tubing. Radiographic computed tomography and metallography were used to evaluate the suitability of the welds using three criteria: weld closure length, thickness, and width. All additively manufactured test welds closely matched the conventional tubing for these criteria

additive manufacturing↗

Machining of Thin-Walled Structures From Stiffness-Driven Additively Manufactured Preform Geometry

Additive manufacturing provides the means to build component preforms with reduced excess material to create functional parts. In the case of aero-structural and aero-engine components, additive manufacturing technologies offer the possibility to substantially reduce the volume of material to be removed by machining operations. To achieve this objective, the preform must be built with the minimum material necessary to contain the final geometry and simultaneously provide enough stiffness to withstand the magnitude of the machining forces. This work describes a computationally efficient method to calculate the geometry required from the preform to reliably manufacture typical thin-walled structures via finish machining processes. This is achieved by defining the preform with near constant static stiffness across the width of the preform, in combination with a prescribed magnitude of stiffness at the top edge of the preform. The prescribed static stiffness is the function of the machining force magnitude, a direct consequence of the preselected cutting conditions. In conclusion, this article illustrates the application of the method to a straight single boundary thin-walled structure as an introduction case and for ease of description.

Additive manufacturing↗

A coupled fluid-mechanical workflow to simulate the directed energy deposition additive manufacturing process

Simulation of additive manufacturing processes can provide essential insight into material behavior, residual stress, and ultimately, the performance of additively manufactured parts. In this work, we describe a new simulation based workflow utilizing both solid mechanics and fluid mechanics based formulations within the finite element software package SIERRA (Sierra Solid Mechanics Team in Sierra/Solid Mechanics 4.52 User’s Guide SAND2019-2715. Technical report, Sandia National Laboratories, 2011) to enable integrated simulations of directed energy deposition (DED) additive manufacturing processes. In this methodology, a high-fidelity fluid mechanics based model of additive manufacturing is employed as the first step in a simulation workflow. This fluid model uses a level set field to track the location of the boundary between the solid material and background gas and precisely predicts temperatures and material deposition shapes from additive manufacturing process parameters. Next, the resulting deposition shape and temperature field from the fluid model are then mapped into a solid mechanics formulation to provide a more accurate surface topology for radiation and convection boundary conditions and a prescribed temperature field. Solid mechanics simulations are then conducted to predict the evolution of material stresses and microstructure within a part. By combining thermal history and deposition shape from fluid mechanics with residual stress and material property evolutions from solid mechanics, additional fidelity and precision are incorporated into additive manufacturing process simulations providing new insight into complex DED builds.

36 MATERIALS SCIENCE↗