Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AC resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Characterization of Magnetoacoustic Emission Related to Structural Properties of Ferromagnets

An extensive study of magnetoacoustic emission (MAE) properties has been performed over the past several years. As a result, the dependence of the spectral characteristics of MAE on certain microstructural variations and uniaxially applied stress in a particular type of low carbon steel are now well known. The embrittlement-causing concentration of certain atomic species, e. g., tin, sulphur, phosphorous etc., at the grain boundaries of this steel creates strong potential barriers resisting the motion of non-180 domain walls which is the source of MAE. (Since the only type of non-180 domain walls in this material are 90 domain walls, the term 90 domain wall will be used throughout this paper in place of non-180 domain wall.) An MAE burst produced during one-half cycle of a hysteresis loop at a low AC magnetic field frequency (e. g., 0.7 Hz) shows two sub-peaks; the leading peak is usually sharp and short-lived, while the trailing peak is usually smooth and long-lasting. It has been shown that the enhanced domain wall-defect interaction, due to the strengthened potential barriers, causes an increase in the asymmetry of the MAE signal by suppressing the leading sub-peak and amplifying the trailing sub-peak. This phenomena is due to the delayed motion of the 90 domain walls. The effect of a tensile stress applied parallel to the external AC magnetic field is to diminish the MAE. On the other hand, the amplitude of the MAE burst has been shown to be a non-monotonic function of the stress amplitude. Recently, our study has concentrated on obtaining quantitative values for parameters computed from the MAE spectra averaged over a sufficient number of cycles to achieve statistical stability. Nevertheless, certain fundamental elements of the MAE characteristics remain unexplained.

Namkung, M.↗
DOE OSTI2021

Polaronic transport and thermoelectricity in Mn 3 Si 2 Te 6 single crystals

Here, we carried out a comprehensive study of the structural, electrical transport, thermal, and thermodynamic properties in ferrimagnetic Mn 3 Si 2 Te 6 single crystals. Mn and Te K -edge x-ray absorption spectroscopy and synchrotron powder x-ray diffraction were measured to provide information on the local atomic environment and the average crystal structure. The dc and ac magnetic susceptibility measurements indicate a second-order paramagnetic to ferrimagnetic transition at T c ~ 74 K, which is further confirmed by the specific heat measurement. Mn 3 Si 2 Te 6 exhibits semiconducting behavior along with a large negative magnetoresistance of -87% at T c and a relatively high value of thermopower up to ~10 mV/K at 5 K. Besides the rapidly increasing resistivity ρ(T) and thermopower S(T) below 20 K, the large discrepancy between the activation energy for resistivity E ρ and thermopower E S above 20 K indicates the polaronic transport mechanism. Furthermore, the thermal conductivity κ(T) of Mn 3 Si 2 Te 6 is notably rather low, comparable to Cr 2 Si 2 Te 6 , and is strongly suppressed in the magnetic field across T c , indicating the presence of strong spin-lattice coupling, also similar with Cr 2 Si 2 Te 6 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

A High-Frequency Planar Transformer with Medium-Voltage Isolation

This paper presents the design of a low-loss, high-frequency planar transformer having medium-voltage (10’s of kV) isolation capability while transformer primary and secondary windings are interleaved to reduce losses. Medium-voltage isolation between adjacent printed circuit board (PCB) layers is extremely challenging using traditional PCB dielectrics. The isolation requirement is met using PCB with 7 kV/mil polyimide (Panasonic Felios RF775) as the dielectric, and by an appropriate layout of the windings and the inter-winding vias. The transformer is used to implement a dual active bridge (DAB) converter in a stackable dc-ac architecture where the dc port is connected to a photovoltaic (PV) string and ac outputs are connected in series to achieve direct PV string-to-medium voltage conversion without the need for low-voltage collection or a bulky line frequency transformer. Since each DAB transformer processes time-varying power, a design methodology is developed to minimize line-cycle-averaged losses. Experimental results are presented for a 1:1 planar transformer in a 7.5 kW SiC-based dc-to-ac module operating at 200 kHz. Isolation of 26 kV between the primary and secondary layers and between the windings and the core is verified using a hipot tester.

insulation resistance↗
NASA NTRS2001

Characterization of Transducers and Resonators under High Drive Levels

In many applications, piezoelectric transducers are driven at AC voltage levels well beyond the level for which the material was nominally characterized. In this paper we describe an experimental setup that allows for the determination of the main transducer or resonator properties under large AC drive. A sinusoidal voltage from a waveform generator is amplified and applied across the transducer/resonator in series with a known high power resistor. The amplitude of applied voltage and the amplitude and the relative phase of the current through the resistor are monitored on a digital scope. The frequency of the applied signal is swept through resonance and the voltage/current signals are recorded. After corrections for the series resistance and parasitic elements the technique allows for the determination of the complex impedance spectra of the sample as a function of frequency. In addition, access to the current signal allows for the direct investigation of non-linear effects through the application of Fourier transform techniques on the current signal. Our results indicate that care is required when interpreting impedance data at high drive level due to the frequency dependence of the dissipated power. Although the transducer/resonator at a single frequency and after many cycles may reach thermal equilibrium, the spectra as a whole cannot be considered an isothermal measurement due to the temperature change with frequency. Methods to correct for this effect will be discussed. Results determined from resonators of both soft and hard PZT and a ultrasonic horn transducer are presented.

transducers↗
NASA NTRS2015

A Fiber-Optic Current Sensor for Lightning Measurement Applications

An optical-fiber sensor based on Faraday Effect is developed for measuring total lightning electric current. It has many unique capabilities not possible with traditional current sensors. Designed for aircraft installation, the sensor is lightweight, non-conducting, structure-conforming, and is immune to electromagnetic interference, hysteresis and saturation. It can also be used on windmills, lightning towers, and can help validate lightning detection network measurements. Faraday Effect causes light polarization to rotate when the fiber is exposed to a magnetic field in the direction of light propagation. Thus, the magnetic field strength can be determined from the light polarization change. By forming closed fiber loops and applying Ampere's law, measuring the total light rotation yields the total current enclosed. The broadband, dual-detector, reflective polarimetric scheme allows measurement of both DC component and AC waveforms with about 60 dB dynamic range. Three sensor systems were built with different sensitivities from different laser wavelengths. Operating at 850nm, the first system uses twisted single-mode fiber and has a 150 A - 150 KA range. The second system operates at 1550nm, uses spun polarization maintaining fiber, and can measure 400 A - 400 KA. Both systems were validated with rocket-triggered lightning measurements and achieved excellent results when compared to a resistive shunt. The third system operates at 1310nm, uses spun polarization maintaining fiber, and can measure approximately 300 A - 300 KA. High current measurements up to 200 KA were demonstrated at a commercial lightning test facility. The system was recently installed on an aircraft and flown near icing weather conditions.

Nguyen, Truong X.↗
DOE OSTI2021

A High-Frequency Planar Transformer with Medium-Voltage Isolation: Preprint

This paper presents the design of a low-loss, high-frequency planar transformer having medium-voltage (10's of kV) isolation capability while transformer primary and secondary windings are interleaved to reduce losses. Medium-voltage isolation between adjacent printed circuit board (PCB) layers is extremely challenging using traditional PCB dielectrics. The isolation requirement is met using PCB with $7$\,kV/mil polyimide (Panasonic Felios RF775) as the dielectric, and by an appropriate layout of the windings and the inter-winding vias. The transformer is used to implement a dual active bridge (DAB) converter in a stackable dc-ac architecture where the dc port is connected to a photovoltaic (PV) string and ac outputs are connected in series to achieve direct PV string-to-medium voltage conversion without the need for low-voltage collection or a bulky line frequency transformer. Since each DAB transformer processes time-varying power, a design methodology is developed to minimize line-cycle-averaged losses. Experimental results are presented for a 1:1 planar transformer in a 7.5\,kW SiC-based dc-to-ac module operating at 200 kHz. Isolation of 26 kV between the primary and secondary layers and between the windings and the core is verified using a hipot tester.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

Packaging Development for a 1200V SiC BiDFET Switch Using Highly Thermally Conductive Organic Epoxy Laminate

A novel 1.2 kV/10A, 4H-SiC monolithic, bidirectional switch has been developed for use in cycloconverter applications to facilitate high-frequency direct AC-to-AC power conversion and enables new power converter topologies. A new packaging solution, utilizing a 100 µm flexible polyimide organic laminate substrate is developed to mitigate thermo-mechanical stress during power cycling and enable smaller form factor and lower cost. Multiphysics simulations and static tests were conducted to show performance characterization of the module and compare it against metallic substrates. A new organic laminate epoxy resin composite dielectric (ERCD) is also evaluated for superior thermal performance and shows 63% reduction in junction to case resistance compared to DBC substrates.

Silicon Carbide, Bi-directional switch, BiDFET, MO↗
NASA NTRS1993

Effect of cycling on the lithium/electrolyte interface in organic electrolytes

Nondestructive methods such as ac impedance spectroscopy and microcalorimetry are used to study the effect of cell cycling on the lithium/electrolyte interface. The reactivity of both uncycled and cycled lithium towards various electrolytes is examined by measuring the heat evolved from the cells under open-circuit conditions at 25 C by microcalorimetry. Cycled cells at the end of charge/discharge exhibited considerably higher heat output compared with the uncycled cells. After 30 d of storage, the heat output of the cycled cells is similar to that of the uncycled cells. The cell internal resistance increases with cycling, and this is attributed to the degradation of the electrolyte with cycling.

Surampudi, S.↗
DOE OSTI2021

Advances in Processing, Manufacturing, and Applications of Magnetic Materials

Magnetic materials are increasingly important for many green energy technologies. Probably, the best known of these are permanent magnets. They are used to supply a magnetic field and are widely used in actuators, motors, generators, data storage, and sensors. These are “hard magnets,” meaning that they retain a large permanent magnetization (difficult to be demagnetized), which is what makes them so useful in motors where an opposing magnetic field can be used to push against them. A coercivity (resistance to demagnetization) of ~400 Oe (32,000 A/m) or more is typically the threshold value for a hard magnet and is typical of isotropic sintered ferrite (SrFe 12 O 19 ) such as found in many “refrigerator magnets.” Comparably important soft magnets are useful for directing magnetic fields and can be very easily (de)magnetized. As such, they typically have a coercivity < 12.5 Oe (1000 A/m), and specialized very soft magnets can have coercivities < 0.00125 Oe (1 A/m). Some common applications include coil cores, transformer cores, and magnetic shielding. Additionally, they are important for many AC electrical applications such as inductors, filters, and resonators, particularly at high frequencies up to and including microwaves.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Frequency-dependent characteristics and trap studies of lattice-matched (x = 0.53) and strained (x greater than 0.53) In(0.52)Al(0.48)As/In(x)Ga(1-x)As HEMT's

The low-frequency characteristics of InAlAs/In(x)Ga(1-x)As high-electron-mobility transistors (HEMTs) are studied, and trap densities are evaluated. The HEMTs' transconductance g(m) and output resistance R(ds) dispersion are smallest for 60 percent indium (In) content and largest for 53 percent In. The maximum dispersion for the 53 percent In sample is about 6 percent for g(m) and about 13.3 percent for R(ds), corresponding to lower values than observed in MESFETs. The R(ds) dispersion characteristics are weaker than in AlGaAs/GaAs HEMTs and manifest themselves primarily up to 100 kHz. An analysis of the dispersion results indicates that, unlike in the case of MESFETs, the channel region under the gate rather than the access regions is responsible for the dispersion. Interface state densities were extracted by the AC conductance method and were found to follow the same trend as the g(m) and R(ds) dispersion.

Ng, Geok-Ing↗
NASA NTRS2013

A Particle-in-Cell Simulation for the Traveling Wave Direct Energy Converter (TWDEC) for Fusion Propulsion

A Particle-in-cell simulation model has been developed to study the physics of the Traveling Wave Direct Energy Converter (TWDEC) applied to the conversion of charged fusion products into electricity. In this model the availability of a beam of collimated fusion products is assumed; the simulation is focused on the conversion of the beam kinetic energy into alternating current (AC) electric power. The model is electrostatic, as the electro-dynamics of the relatively slow ions can be treated in the quasistatic approximation. A two-dimensional, axisymmetric (radial-axial coordinates) geometry is considered. Ion beam particles are injected on one end and travel along the axis through ring-shaped electrodes with externally applied time-varying voltages, thus modulating the beam by forming a sinusoidal pattern in the beam density. Further downstream, the modulated beam passes through another set of ring electrodes, now electrically oating. The modulated beam induces a time alternating potential di erence between adjacent electrodes. Power can be drawn from the electrodes by connecting a resistive load. As energy is dissipated in the load, a corresponding drop in beam energy is measured. The simulation encapsulates the TWDEC process by reproducing the time-dependent transfer of energy and the particle deceleration due to the electric eld phase time variations.

Chap, Andrew↗
DOE OSTI2021

Lithium thiostannate spinels: air-stable cubic semiconductors.

Lithium chalcogenide materials have been studied less than other alkali metal analogs and are of interest as ion conductors and semiconductors capable of thermal neutron detection. Herein, we describe the structural, thermal, magnetic, electronic, and ionic properties of a new family of cubic lithium thiospinels Li2MSn3S8 (M = Mg, Fe, Mn, Ni, Co) and Li1.66CuSn3.33S8. All compounds crystallize in the Fd (3) over barm space group and exhibit site occupancy disorder with Sn and M on the octahedral site for M = Mg, Fe, Mn, Ni, Co. The Li1.66CuSn3.33S8 compound also exhibits occupancy disorder on the tetrahedral sites between Li and Cu, as well as on the octahedral sites between Li and Sn. We demonstrate the ability to tune the physical properties of the compounds by changing their composition. By tuning the identity of the transition metal in the structure, the optical band gaps can vary between 0.91(2) and 2.19(2) eV, and electrical resistivities between 2.8 x 10(3) Omega-cm and 2.2 x 10(7)Omega-cm can be achieved. Density functional theory calculations for Li2MgSn3S8 and Li1.66CuSn3.33S8 suggest that both materials have indirect band gaps and significantly dispersive conduction bands. A bandwidth dispersion of 0.75 and 0.70 eV along the Gamma -> M direction in the conduction band are predicted for Li2MgSn3S8 and Li1.66CuSn3.33S8, respectively, with an electron effective mass of 0.49 and 0.55 m(e) at the Gamma point. The hole effective mass in the valence band is calculated to be 1.25 me at the M point and 0.75 me at the L point for Li2MgSn3S8 and Li1.66CuSn3.33S8, respectively. The ionic/electronic conductivity of each compound was determined using AC electrochemical impedance spectroscopy.

Quintero, Michael A.↗
NASA NTRS1987

AC impedance analysis of polypyrrole thin films

The AC impedance spectra of thin polypyrrole films were obtained at open circuit potentials from -0.4 to 0.4 V vs SCE. Two limiting cases are discussed for which simplified equivalent circuits are applicable. At very positive potentials, the predominantly nonfaradaic AC impedance of polypyrrole is very similar to that observed previously for finite porous metallic films. Modeling of the data with the appropriate equivalent circuit permits effective pore diameter and pore number densities of the oxidized film to be estimated. At potentials from -0.4 to -0.3 V, the polypyrrole film is essentially nonelectronically conductive and diffusion of polymer oxidized sites with their associated counterions can be assumed to be linear from the film/substrate electrode interface. The equivalent circuit for the polypyrrole film at these potentials is that previously described for metal oxide, lithium intercalation thin films. Using this model, counterion diffusion coefficients are determined for both semi-infinite and finite diffusion domains. In addition, the limiting low frequency resistance and capacitance of the polypyrrole thin fims was determined and compared to that obtained previously for thicker films of the polymer. The origin of the observed potential dependence of these low frequency circuit components is discussed.

Penner, Reginald M.↗
NASA NTRS1977

Observations of intense velocity shear and associated electrostatic waves near an auroral arc

Simultaneous measurements of energetic particles and ac electric fields made by the javelin sounding rocket NASA 8:56 during the late expansion phase of a magnetic storm have revealed an intense shear in plasma flow of magnitude 20 (m/s)/m at the edge of an auroral arc. Structure with two characteristic scales sizes is displayed in the region of shear. Larger structures are of the order of several kilometers in size. Intense irregularities with characteristic wavelengths smaller than the scale size of the shear have also been detected. The large-scale changes in the orientation of the charge sheet at the edge of the arc may be due to the Kelvin-Helmholtz branch; shorter-wavelength modes may be related to the shear driven resistive drift wave. Observations are consistent with the suggestion that velocity shear instabilities may play a role in the formation of high-latitude irregularities.

Kelley, M. C.↗
DOE OSTI2021

Increase resistance for efficient heating

Conductors for use in heating systems are provided. The conductors are configured to have an extended current path for the current and increased resistance as seen by the current. The heating system may be an induction system. For example, the conductor may comprise a conductive material having a surface which faces an induction coil of an oscillating circuit. This surface may have a predetermined pattern of peaks and valleys. The peaks and valleys form a non-linear current path for the induced current when exposed to an electromagnetic field generated by the oscillating circuit. Other conductors such as a heat pipe may be used. The pipe may have walls with varying thicknesses over its length. The varying thicknesses may include a first thickness and a second thickness which alternate. The heat pipe may be used in an induction or direct contact heating system where AC is directly applied to the pipe.

Kisner, Roger A.↗
DOE OSTI2024

Magnetic anisotropy in single-crystalline antiferromagnetic Mn 2 Au

Multiple recent studies have identified the metallic antiferromagnet Mn 2 ⁢Au to be a candidate for spintronic applications due to apparent in-plane anisotropy, preserved magnetic properties above room temperature, and current-induced Néel vector switching. Crystal growth is complicated by the fact that Mn 2 ⁢Au melts incongruently. We present a bismuth flux method to grow millimeter-scale bulk single crystals of Mn 2 ⁢Au in order to examine the intrinsic anisotropic electrical and magnetic properties. Flux quenching experiments reveal that the Mn 2 ⁢Au crystals precipitate below 550°⁢C, about 100⁢°⁢C below the decomposition temperature of Mn 2 ⁢Au. Bulk Mn 2 ⁢Au crystals have a room-temperature resistivity of 16–19 µ⁢Ωcm and a residual resistivity ratio of 41. Mn 2 ⁢Au crystals have a dimensionless susceptibility on the order of 10 –4 (SI units), comparable to calculated and experimental reports on powder samples. Single-crystal neutron diffraction confirms the in-plane magnetic structure. The tetragonal symmetry of Mn 2 ⁢Au constrains the ab-plane magnetic susceptibility to be constant, meaning that χ 100 =χ 110 in the low-field limit, below any spin-flop transition. We find that three measured magnetic susceptibilities χ 100 , χ 110 , and χ 001 are the same order of magnitude and agree with the calculated prediction, meaning the low-field susceptibility of Mn 2 ⁢Au is quite isotropic, despite clear differences in ab-plane and ac-plane magnetocrystalline anisotropy. Mn 2 ⁢Au is calculated to have an extremely high in-plane spin-flop field above 30 T, which is much larger than that of another in-plane antiferromagnet, Fe 2 ⁢As (less than 1 T). Finally, the subtle anisotropy of intrinsic susceptibilities may lead to dominating effects from shape, crystalline texture, strain, and defects in devices that attempt spin readout in Mn 2⁢ Au.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Multi–length scale characterization of point defects in thermally oxidized, proton irradiated iron oxides

A key for the success of safe nuclear power generation system is to consider structural materials that are economical, meet mechanical property needs, possess good corrosion resistance, and are radiation tolerant. Nevertheless, fundamental insights that elucidate the details of radiation damage on materials corrosion performance are lacking. This includes the behavior of surface oxides which often regulate corrosion. For example, it is unclear how non-equilibrium point defects, oxide structure, mass transport in oxides, and subsequent oxidation behavior are altered by the radiation. Here, in this work, some of the effects of proton irradiation on the attributes of point defects, iron oxide microstructures, and the physical nature of the oxidation product were correlated with corrosion behavior. Iron oxides, fabricated by thermal oxidation in air at 400°C and 800°C for 1 h, were subjected to 200 keV, 0.03 dpa (displacements per atom) of proton irradiation, and subjected to corrosion reactivity assessment using AC and DC electrochemical methods. Experimental methods that target materials information at different length scales, such as positron annihilation spectroscopy (atomistic), transmission electron microscopy (mesoscopic), and electrochemical methods (macroscopic), were coupled to shed light on the impact of radiation-induced defect modifications and structural changes in oxides on corrosion reactivity which ultimately affects durability in harsh environments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Power Analysis of an ePump Applied to the Linear Functions of an Agricultural Planter

Like many other industries, the agricultural industry has recently ex-perienced pressure to reduce vehicle emissions while improving productivity. Electric actuation is perceived as a viable solution to replace or augment hydrau-lic and mechanical actuation. However, electrification presents challenges with regards to linear functions, where hydraulic actuators have advantages in terms of compactness, tolerance to contamination and resistance to shocks. A combined electro-hydraulic actuation architecture can leverage the benefits of both electric and hydraulic actuation, while reducing the drawbacks of both approaches. This work investigates the potential of a centralized electric driven pump (ePump) system powering the pressure-controlled linear functions of an agricul-tural planter, with the goal of improving the operating point of the main supply pump. In this application, the rotary functions are hydraulically actuated, alt-hough such a solution could be applied also to electric rotary actuation. This is accomplished by setting the ePump to boost the pressure supplied by the tractor to the level required by the linear functions. An accumulator is used to stabilize the flow requirements of the linear functions, and control the pressure supplied to the actuators. Two control schemes are proposed for the regulation of the ac-cumulator pressure, one favoring an efficient operating point for the ePump, the other favoring stable steady state operation. A simulation model of the baseline system and proposed system is developed and validated using experimental data from a full-scale machine. Using the vali-dated simulation, both control architectures are then evaluated for improvement in system power consumption and dynamic requirements on the ePump to assess their effectiveness. Both systems demonstrate significant improvement in power consumption over the baseline system, with the best solution improving effi-ciency by 64%.

24 POWER TRANSMISSION AND DISTRIBUTION↗