Engineering Papers⌕ Search

DOE OSTI · 923209

Final Scientific Report

Abstract

NanoDynamics Inc. has undertaken a study to develop and demonstrate an anode-supported solid oxide fuel cell capable of generating a minimum of 20 W per cell on hydrogen. The cell technology will also be assed for operation on renewable hydrocarbon-based fuels such as biomass gas, as well its applicability for larger-scale power production. The project was divided into five sub-tasks, the first of which was the development and refinement of the cell manufacturing processes of gel-casting and paste extrusion for the fabrication of planar and tubular anode supports. These methods exhibited high production yields with excellent reproducibility. Using a conventional YSZ-based cell as a performance benchmark, new materials-sets and cell configurations were developed. Three prototype configurations were implemented, the best generating an average of 10 W per cell, and exhibiting excellent potential for further development and scale-up. Using a variety of techniques such as modifying the materials-set, microstructure, and cell configuration, cells with an average power output of 22.7 W were demonstrated, 13.5% in excess of the 20 W project goal. Thermal cycling was performed on such cells, and it was found that over a regime of 150 cycles (approximately 300 h), the cell power increased by 1.8%. So-called “short-stacks” comprised of up to 6 cells were fabricated to study the feasibility of further stack scale-up. Such a 6-cell short-stacks operated on dry hydrogen exhibited power outputs of 80 W, a 6.4% power increase from their constituent cells, showing that the cells had excellent potential for further scale-up. Optimized Rev A cells were built into a 3-cell stack, and found to produce 63.42 W operating on hydrogen, and 58.18 W on methane. The feasibility of a biogas-fed SOFC was also investigated. Utilizing in-house developed catalysts, methane conversion and hydrogen yield was found to be 98 and 42%, respectively. By incorporating this catalyst material into prototype Rev A cells, long-term stability tests showed that for over 200 h of operation, the cell power increased by approximately 10%. It can be concluded that the technology developed by NanoDynamics during this project exceeded the project goal of 20 W/cell by 13.5%, and exhibits excellent potential for further development and scale-up.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Finnerty, Caine. 2008-01-14. Final Scientific Report. https://doi.org/10.2172/923209. https://engineeringpapers.com/record/osti%3A923209/final-scientific-report

Citations retain the original authors and DOI and include this site’s record URL. If this discovery service contributed to your research, you can also cite Engineering Papers by Indiciae: BibTeX · RIS.

KEEP EXPLORING

Related reports

Hydrotreating pine-derived catalytic fast pyrolysis oil to jet fuel: Process durability and impact of operating conditions

Hydrotreating woody biomass-derived catalytic fast pyrolysis (CFP) oil to jet fuel has the potential to enhance energy security due to the large abundance of forest and woody resources. CFP oil produced from pine over ZSM-5 was hydrotreated over sulfided NiMo/Al 2 O 3 for 410 h to study the impact of hydrotreating conditions (pressure, temperature, and weight hourly space velocity (WHSV)). The degree of deoxygenation remained high across the tested hydrotreating conditions, and the products contained < 0.01 wt% oxygen. Increasing hydrotreating pressure from 84 to 125 bar enhanced hydrogenation of aromatic rings and the formation of cycloalkanes and increasing the temperature from 385 to 400 degrees C enhanced cracking and the formation of jet-range molecules. Decreasing the weight hourly space velocity from 0.2 to 0.1 g/(g cat h) further enhanced cracking and led to higher gasoline- and lower jet fuel-range fractions. The highest jet fuel fraction (49 wt%) was obtained at 400 degrees C, 125 bar, 0.2 g/(g cat h) WHSV. CFP oils produced from pine over phosphorous-modified ZSM-5 were hydrotreated at this condition for 588 h to investigate the process durability. The hydrogenation performance of the catalyst gradually stabilized in approximately 300 h after which the product composition remained constant. Of the final hydrotreated CFP oil, 53 wt% fell in the jet fuel range with most of the tested fuel properties meeting ASTM D4054 and/or ASTM D7566 specifications. The freeze points were < -50 degrees C vs. guideline of < -40 degrees C and the viscosities at -20 degrees C were 3.8-4.1 mm 2 /s vs guideline of 8 mm 2 /s. Increasing the fraction of cycloalkanes could increase the cetane number and heating value, which did not meet the guidelines.

09 BIOMASS FUELS↗

Suppressing CO formation in low-temperature methanol steam reforming via Ce-modified CuZnGa layered oxide catalysts

Cu-based layered double hydroxides (LDHs) are widely recognized as effective catalysts for low-temperature methanol steam reforming, yet achieving high hydrogen productivity together with near-complete suppression of CO formation remains challenging. Here, we report the synthesis and evaluation of a series of CuZnGa LDH-derived catalysts and Ce-modified analogues prepared via an aqueous miscible organic method, which enables high metal dispersion and precise structural control. The optimized CuZnGa catalyst exhibits a hydrogen production rate of 16.9 µmol H 2 ·g cat −1 ·s −1 at 180 °C with an H 2 /CO ratio exceeding 3500, outperforming many state-of-the-art low-temperature systems. Importantly, the incorporation of small amounts of Ce further suppresses CO formation while maintaining high hydrogen productivity. Combined spectroscopic characterization and density functional theory calculations reveal that Ce is incorporated into the LDH lattice by substituting Ga 3+ sites up to a critical threshold, beyond which highly dispersed CeO x species are formed. These species provide mobile lattice oxygen that participates in a Mars-van Krevelen-type pathway, selectively oxidizing CO and suppressing the reverse water-gas shift reaction. This study establishes a clear relationship between Ce speciation, oxygen mobility, and catalytic selectivity in LDH-derived systems. The resulting catalysts demonstrate the potential of interface-engineered Cu-based materials for efficient low-temperature hydrogen production with minimal CO contamination.

09 BIOMASS FUELS↗

Graphitization of banana peel – synergistic effect of Ca and other elements of the biomass on carbon structure transformation

Recently, growing interest has been observed in using calcium as an effective catalyst for graphitizing disordered carbon materials derived from biomass and bioprecursors, such as cellulose and lignin, at relatively low tem peratures (<2000 °C). Herein, it is demonstrated that in the presence of elements such as calcium, silicon, sulfur, and potassium, which are abundant in banana peel composed of cellulose and lignin base, graphitization occurs much more effectively. The addition of external calcium source, in the form of calcium carbonate, to the banana peel-derived carbon and heat-treatment of the mixture under protective atmosphere up to 1750 °C results in a significant increase in the degree of the graphitization order and local formation of graphite crystals, whereas the same preparation and heat-treatment procedure applied to carbon material derived from pristine cellulose does not lead to such effective graphitization. It is indicated that the graphitization of banana peel carbon occurs due to the synergistic effect of the external Ca-based catalyst and the internal elements present in the raw biomass, supporting the transformation of the disordered graphene-like layers into graphitic structures. These findings are important for the future production of green graphite from biomass

09 BIOMASS FUELS↗