Engineering Papers⌕ Search

DOE OSTI · 1905579

The Cypress Sandstone Seal System

Abstract

The Cypress Sandstone is the youngest and shallowest unit in the Illinois Basin that was featured in the United States Carbon Utilization and Storage Atlas IV as a target for saline carbon storage with an estimated 0.2 to 2.3 GT of storage potential. Additional research on a residual oil zone (ROZ) developed within the Cypress Sandstone has delineated 27 prospects with approximately 290.8 million m3 (1.8 billion barrels) of oil in place. 21 to 31 million m 3 (144 to 196 million barrels) of oil is estimated to be recoverable using carbon dioxide enhanced oil recovery (CO 2 -EOR). Storage of CO 2 associated with EOR in these ROZ prospects alone, not accounting for associated main pay zones (MPZs), underlying brine formation, or intervals adjacent to or between prospects, is estimated to be up to 10.4 billion tonnes. The Cypress Sandstone is thus well understood to be a CO 2 injection target, both for EOR and associated storage. However, the seal system overlying the Cypress Sandstone is poorly understood. Unlike deeper formations such as the Mt. Simon Sandstone or the St. Peter Sandstone which are either in use as a CO 2 sink or being characterized for prospective storage, respectively, the Cypress is not overlain by hundreds of feet of impermeable shale. Rather, the Cypress is overlain by a lithologically variable interval that is composed generally of shales and limestones with some sandstone in the part of the Basin where the Cypress is deep enough to facilitate CO 2 storage. Also, due to its status as one of the shallowest and most prolific oil reservoirs in the Basin, the seal system overlying the Cypress Sandstone has a relatively high number of legacy well penetrations. The purpose of this report is to characterize the Cypress Sandstone seal system using well logs and available core. Gross thickness, lithology (facies), and mineralogy of seals is described and mapped across the Basin. The column height of CO 2 that can be held is calculated using capillary pressure data from a representative core.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Webb, Nathan D., Willette, Donna C.. 2022-12-16. The Cypress Sandstone Seal System. https://doi.org/10.2172/1905579

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Carbon Capture and Utilization for Protein and Fatty Acids

The unlimited release version of the final report for the "Carbon Capture and Utilization for Protein and Fatty Acids" project. This project advanced an integrated open raceway algae cultivation and processing system to engineering scale for carbon capture and utilization (CCU) from the flue gas of a naphtha-fired power plant.

02 PETROLEUM↗

Oil in Alaska North Slope Gas Hydrate Reservoir: Micro-CT and Flow Simulation Insights into Permeability

Gas hydrate-bearing sands on the Alaska North Slope (ANS) host minor volumes of crude oil whose impact on formation permeability has never been quantified relative to a gas hydrate reservoir system. Here, we combine in situ pressure-core microcomputed-tomography (μ-CT), thermogravimetric analysis (TGA), gas-chromatography–mass-spectrometry (GC–MS), scanning-electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), and Stokes-flow simulation to (i) quantify oil saturation, (ii) infer its source, and (iii) evaluate its influence on permeability after gas-hydrate dissociation. μ-CT and SEM-EDS imaging identify the host sediment as silty, with some grain-coating clay present. Eight representative 3003-voxel subvolumes extracted from a preserved pressure core (Core 15P-3c, from the B1 sand (unit B), HYDRATE 02 Geo Data Well (GDW), 886.96–887.29 m measured depth, MD) exhibit porosities of 0.34–0.37 and an average oil saturation of 0.09 ± 0.03, in comparison to an independent TGA-based estimate of 0.16. GC-MS fingerprints obtained from an adjacent depressurized core (Core 17P-1, 891.37–891.44 m MD), together with oil pore habit revealed by μ-CT, suggest that the oil is partly native but also includes contributions from mineral oil-based drilling fluid contamination. Further analysis of oil–porewater interactions and flushing tests confirms that native oil saturation in the analyzed samples ranges from 0.04 to 0.08 with an average of approximately 0.06, and the oil is highly immobile. Flow simulations demonstrate that the native oil saturation of ≈0.06 reduces permeability by approximately 50% due to both pore blockage and increased flow-path tortuosity. These findings reveal the potential presence of native oil within the ANS gas hydrate reservoir and suggest that future simulation models may need to account for its impact on permeability to improve long-term performance predictions of gas and water production.

02 PETROLEUM↗

Quantum Enhanced Fiber Sensing for Oil and Gas Applications (Final Technical Report)

The major goal of the project was to develop a quantum sensing approach compatible with current infrastructure in the oil and gas industry that could provide a quantum enhancement, with a focus towards pipeline leak detection. The proposed approach to achieving this goal consisted of the use of quantum states of light to enhance the sensitivity of fiber optic sensors beyond the classical limit. To address the limitations of existing commercial leak detection, the project focused on the study of two technologies: distributed acoustic sensors (DAS) and fiber Bragg grating (FBG)-based sensors. The initial phase of the project centered around the identification and mitigation of dominant sources of classical noise to enable operation at the classical shot noise limit (SNL). The second phase focused on the use of quantum resources to obtain sensitivities beyond the classical SNL. The final phase sought to combine quantum noise reduction techniques with advanced dynamical classical noise cancelation approaches.

02 PETROLEUM↗