Engineering Papers⌕ Search

DOE OSTI · 1581139

Initial DOE SNF Standardized Canister Storage Configuration Alternatives Study

Abstract

This study looks at storage configuration alternatives for United States Department of Energy (DOE) Spent Nuclear Fuel (SNF) Standardized Canisters loaded with DOE-owned SNF. The focus of the study is for the DOE SNF Standardized Canisters that would be packaged in the Idaho Nuclear Technology and Engineering Center (INTEC) area at Idaho National Laboratory (INL), but its general findings are useful across the DOE Complex. The study considered storage in existing facilities, modified existing facilities, new facilities, and new modular systems. The existing INTEC facilities considered in the study include the CPP-603 Irradiated Fuel Storage Facility (IFSF), the CPP-749 Underground Fuel Storage Facility (UFSF), the CPP-666 SNF Wet Storage Basin Facility, CPP-1774 Three Mile Island (TMI) Independent Spent Fuel Storage Facility (ISFSF), and the CPP-2707 Cask Pad Facility. The new facilities considered in the study include the Foster Wheeler designed Idaho Spent Fuel (ISF) Independent Spent Fuel Storage Installation (ISFSI) and some conceptual designs. The new modular systems considered in the study include Holtec International’s HI-STAR/HI-STORM, NAC International’s MAGNASTOR/UMS/MPC and Orano TN’s MATRIX/NUHOMS. Based on considerations of various factors, including but not limited to capacity, impact to facility operations, capital costs, expenditure rate, licensing issues, agreements with the State of Idaho, and road ready conditions, new modular storage systems from commercial vendors may have clear advantages over other storage alternatives. This is further supported by recent experience with West Valley Demonstration Project (WVDP) storage project for High Level Waste Glass canisters.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Thomas, Daniel Albert. 2019-09-30. Initial DOE SNF Standardized Canister Storage Configuration Alternatives Study. https://doi.org/10.2172/1581139

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗