NASA NTRS · 20210018710
Overview of high-temperature materials and thermal protection systems used by NASA.
Explore connections, maps & timelines
Stan Bouslog. High-Temperature Materials. https://ntrs.nasa.gov/citations/20210018710
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
This presentation will update the community on the development of conformal ablative TPS. As described at IPPW-10, in FY12, the CA-TPS element focused on establishing materials requirements based on MSL-type and COTS Low Earth orbit (LEO) conditions (q 250 Wcm2) to develop and deliver a conformal ablative TPS. This involved downselecting, manufacturing and testing two of the best candidate materials, demonstrating uniform infiltration of resins into baseline 2-cm thick carbon felt, selecting a primary conformal material formulation based on novel arc jet and basic material properties testing, developing and demonstrating instrumentation for felt-based materials and, based on the data, developing a low fidelity material response model so that the conformal ablator TPS thickness for missions could be established. In addition, the project began to develop Industry Partnerships. Since the nominal thickness of baseline carbon felts was only 2-cm, a partnership with a rayon felt developer was made in order to upgrade equipment, establish the processes required and attempt to manufacture 10-cm thick white goods. A partnership with a processing house was made to develop the methodology to carbonize large pieces of the white goods into 7.5-cm thick carbon felt.In FY13, more advanced testing and modeling of the downselected conformal material was performed. Material thermal properties tests and structural properties tests were performed. The first 3 and 4-point bend tests were performed on the conformal ablator as well as PICA for comparison and the conformal ablator had outstanding behavior compared to PICA. Arc jet testing was performed with instrumented samples of both the conformal ablator and standard PICA at heating rates ranging from 40 to 400 Wcm2 and shear as high as 600 Pa. The results from these tests showed a remarkable improvement in the thermal penetration through the conformal ablator when compared to PICAs response. The data from these tests were used to develop a mid-fidelity thermal response model. Additional arc jet testing in the same conditions on various seam designs were very successful in showing that the material could be joined with a minimum of adhesive and required no complicated gap and gap filler design for installation. In addition, the partnership with industry to manufacture thicker rayon felt was very successful. The vendor made a 2-m wide by 30-m long sample of 10-cm thick rayon felt. When carbonized, the resulting thickness was over 7.5-cm thick, nearly 4 times the thickest off-the-shelf carbon felt. In FY14, the project has initiated a partnership with another vendor to begin the scale-up manufacturing effort. This year, the vendor will duplicate the process and manufacture at the current scale for comparison with NASA-processed materials. Properties testing and arc jet testing will be performed on the vendor-processed materials. Planning for manufacturing large, 1-m x 1-m, panels will begin as well. In FY15, the vendor will then manufacture large panels and the project will build a 2-m x 2-m Manufacturing Demonstration Unit (MDU).
On February 18th, 2021, the Mars 2020 entry vehicle delivered the Perseverance rover to the surface of Mars. The entry vehicle carried a set of instrumentation installed on the heatshield and backshell to measure aerodynamic and aerothermal performance, named the Mars Entry, Descent, and Landing Instrumentation 2. This set of instrumentation included pressure transducers, thermocouples, heatflux sensors, and a radiometer, as well as a dedicated sensor support electronics system. All MEDLI2 hardware operated as expected during cruise and entry. MEDLI2 sensors gathered accurate pressure measurements in hypersonic through supersonic regimes to reconstruct vehicle attitude and atmospheric profiles. MEDLI2 on the heatshield sensors indicated that surface temperatures, caused by turbulent heating beginning 70 seconds after entry, remained at or below 1430 °C, while heatshield bondline temperatures rose less than 45 °C. Backshell surface TPS temperatures peaked at 630 °C, which was caused primarily by radiative heating measured by several separate sensors. The MEDLI2 temperature and pressure measurements enabled further detailed characterization of the Mars 2020 entry performance, and the flight dataset will provide a wealth of information for the EDL community and future mission designers.
The Mars Sample Return Earth Entry System (MSR-EES) project has selected 3-D Woven Mid-Density Carbon Phenolic (3MDCP) as the baseline thermal protection system (TPS) material for the capsule that will return Martian soil samples to Earth sometime in the 2030’s. A series of experiments in the NASA Ames AHF and IHF arcjets will be used to characterize the performance of 3MDCP and to develop and refine material response models for it. The test objectives for these experiments include obtaining in-depth and surface temperature data, mass loss and surface recession measurements, and char depth measurements. To provided pre- and post-test support for the arcjet experiments, a combined CFD/material response was performed using the DPLR and Icarus code. Pre-and post-test analysis on the 3MDCP arcjet experiments was performed using the DPLR CFD and Icarus material response codes. The codes were not tightly coupled, but boundary condition data required by Icarus (e.g., heat transfer coefficients and surface pressures), were extracted from the CFD solutions. This poster shows comparisons between DPLR/Icarus and the experimental data taken during arcjet experiment AHF-348 where 4-inch diameter iso-q models made from 3MDCP were tested in the 12-inch nozzle of the AHF arcjet. This poster also includes a top-level overview of the CFD/material response arcjet simulation process. Best-practices for running CFD solutions of arcjet experiments including how to determine the inflow conditions for the CFD solution from the arc heater settings are discussed. The required inputs to the material response solver are presented, as well as a discussion of how they can be extracted from the CFD solution.